RUGGEDCOM-SERIAL-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
8
Rows
8
Columns
68

rcSerialPortTable

table
.1.3.6.1.4.1.15004.4.6.1.1 · 1 row entry · 10 columns
Open in standard view 
A list of port entries. The number of entries might be
retreived as the value of object 'rs232Number' from RFC1659.
rcSerialPortEntry entry .1.3.6.1.4.1.15004.4.6.1.1.1
Status and configuration parameters for a port.
Indexes
rcSerialPortNumber
Column Syntax OID
rcSerialPortNumber
The physical Serial Port Number of the device for which this Entry
contains configuration settings.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.1.1.1.1
rcSerialPortIfIndex
The value of ifIndex for the port. This value is same as
'rs232PortIndex' which is the index used for 'rs232PortTable'
in RS-232-MIB.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.15004.4.6.1.1.1.2
rcSerialProtocol
A Serial Protocol supported on the Serial Port represented
by this entry.
RcSerProtocolr/w
Textual Convention: RcSerProtocol Enumeration
Type Values:
1noProtocol
2rawSock
3modbusServer
4modbusClient
5itcsWIN
6itcsTIN
7microlok
8dnp
9dnpRawSock
10mirrorBits
11preemptRawSock
12telnetComport
 .1.3.6.1.4.1.15004.4.6.1.1.1.3
rcSerialPortType
A Serial Port Type supported on the Serial Port represented
by this entry.
RcSerPortTyper/w
Textual Convention: RcSerPortType Enumeration
Type Values:
0none
1rs232
2rs485
3rs422
4tpc
5fiber
 .1.3.6.1.4.1.15004.4.6.1.1.1.4
rcSerialForceHD
Enables forcing half duplex mode of operation on the Serial Port.

While sending data out of the serial port all received data are ignored.
This mode of operation is available only on ports that operate …
Enumerationr/w
Enumerated Values:
1on
2off
3notApplicable
 .1.3.6.1.4.1.15004.4.6.1.1.1.5
rcSerialTurnAround
The amount of delay between the transmission of individual messages
out of the serial port.

For 'rcSerialProtocol' object value modbusServer(3) this value must be non-zero.
It represents delay between se…
millisecondsInteger32r/w
Constraints:
range: 0-1000
 .1.3.6.1.4.1.15004.4.6.1.1.1.6
rcSerialPostTxDelay
The number of bits needed to generate required delay with configured
baudrate('rs232PortOutSpeed') after the last bit of the packet was
sent out before serial UART starts listening to the RX line .

This …
bitsInteger32r/w
Constraints:
range: 0-15
 .1.3.6.1.4.1.15004.4.6.1.1.1.7
rcSerialHoldTime
The maximum amount of time in ms that serial packet can be held in the
queue before being sent to the serial line.

Time is measured from the moment the packet is received from the IP
layer.
millisecondsInteger32r/w
Constraints:
range: 0-15000
 .1.3.6.1.4.1.15004.4.6.1.1.1.8
rcSerialDscp
The value of DS byte to be set in the IP header.

DS byte setting is supported in the egress direction only.
Integer32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.15004.4.6.1.1.1.9
rcSerialRxtoTxDelay
The minimum amount of time in ms that the transmission of a new
message should delay after the last message is received through the
serial port.

This parameter is useful, especially for the half duplex …
millisecondsInteger32r/w
Constraints:
range: 0-1000
 .1.3.6.1.4.1.15004.4.6.1.1.1.10

rcMbServerTable

table
.1.3.6.1.4.1.15004.4.6.2.1 · 1 row entry · 5 columns
Open in standard view 
This table provides configuration options for the ports when 
'rcSerialProtocol'equals modbusServer(3).
rcMbServerEntry entry .1.3.6.1.4.1.15004.4.6.2.1.1
List of all the configuration options for a port for which
'rcSerialProtocol' equals modbusServer(3).
Indexes
rcMbServerPort
Column Syntax OID
rcMbServerPort
The physical Serial Port Number for which this Entry contains the
Modbus Server Protocol configuration settings.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.2.1.1.1
rcMbServerRespTimer
The allowable time to wait for the RTU to start to respond.
millisecondsInteger32r/w
Constraints:
range: 50-10000
 .1.3.6.1.4.1.15004.4.6.2.1.1.2
rcMbServerAuxTcpPort
The alternative TCP port number where a 'rcMbServerPort' may listen
to incoming TCP conncetions.

Note:TCP Modbus Server always listens on TCP port 502.
So this parameter allows the RuggedCom serial devi…
Integer32r/w
Constraints:
range: 1024-65535
 .1.3.6.1.4.1.15004.4.6.2.1.1.3
rcMbServerSendExcep
Allows the RuggedCom Serial Devices to enable or disable sending TCP
Modbus exception back to the master if response has not been
received from the RTU within expected time.
EnabledStatusr/w
Textual Convention: EnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.15004.4.6.2.1.1.4
rcMbServerLinkStats
Enables links statistics collection.
EnabledStatusr/w
Textual Convention: EnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.15004.4.6.2.1.1.5

rcRawSockTable

table
.1.3.6.1.4.1.15004.4.6.4.1 · 1 row entry · 12 columns
Open in standard view 
This table represents the entries for ports configured for Raw Socket
serial protocol on RuggedCom serial devices.
rcRawSockEntry entry .1.3.6.1.4.1.15004.4.6.4.1.1
List of all the configuration options available for a port configured
for Raw Socket serial protocol on Ruggedcom serial devices.
Indexes
rcRawSockPort
Column Syntax OID
rcRawSockPort
The physical Serial Port Number for which this Entry contains
the Raw Socket serial protocol configuration settings.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.4.1.1.1
rcRawSockPackChar
The character that can be used to force forwarding of accumulated
data to the network.

If a packetization character is not configured - object is set to the
value of '256', accumulated data will be forw…
Integer32r/w
Constraints:
range: 0-256
 .1.3.6.1.4.1.15004.4.6.4.1.1.2
rcRawSockPackTimer
The delay in ms from the last received character until when data is
forwarded.
millisecondsInteger32r/w
Constraints:
range: 3-1000
 .1.3.6.1.4.1.15004.4.6.4.1.1.3
rcRawSockPackSize
The maximum number of bytes received from serial port to be
forwarded.
bytesInteger32r/w
Constraints:
range: 64-1401
 .1.3.6.1.4.1.15004.4.6.4.1.1.4
rcRawSockFlowControl
The type of FlowControl to be used on the port.
RcFlowControlr/w
Textual Convention: RcFlowControl Enumeration
Type Values:
1none
2xonXoff
 .1.3.6.1.4.1.15004.4.6.4.1.1.5
rcRawSockTransport
A transport protocol used for IP traffic for protocol on this port.
RcTransportr/w
Textual Convention: RcTransport Enumeration
Type Values:
1udp
2tcp
 .1.3.6.1.4.1.15004.4.6.4.1.1.6
rcRawSockCallDir
Defines following:
- whether to accept an incoming connection 'in(0)' or
- to place an outgoing connection 'out(1)' or
- to place an outgoing connection and wait for incomming 'both(2)'

Note: This pa…
RcCallDirr/w
Textual Convention: RcCallDir Enumeration
Type Values:
0in
1out
2both
 .1.3.6.1.4.1.15004.4.6.4.1.1.7
rcRawSockMaxConn
The maximum number of allowed incoming TCP connections.
Integer32r/w
Constraints:
range: 1-64
 .1.3.6.1.4.1.15004.4.6.4.1.1.8
rcRawSockLocPort
The local IP port to listen to an incoming TCP connection or UDP
datagrams.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.4.1.1.9
rcRawSockRemPort
The remote IP port to use when placing an outgoing connection.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.4.1.1.10
rcRawSockIpAdd
Defines the IpAddress based on the following:
- For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)'
this is the remote IP address to communicate with.
- For incoming TCP connection (server), 'rcRawSoc…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.15004.4.6.4.1.1.11
rcRawSockLinkStats
Enables links statistics collection for RawSocket on this port.
EnabledStatusr/w
Textual Convention: EnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.15004.4.6.4.1.1.12

rcPreemptRSTable

table
.1.3.6.1.4.1.15004.4.6.5.1 · 1 row entry · 12 columns
Open in standard view 
This Table defines the configuration options available for ports 
configured for PreEmptive Raw Socket serial protocol.
rcPreemptRSEntry entry .1.3.6.1.4.1.15004.4.6.5.1.1
A list of port entries with configuration options for ports configured
for PreEmptive Raw Socket protocol.
Indexes
rcPreemptRSPort
Column Syntax OID
rcPreemptRSPort
The physical Serial Port Number for which this Entry contains
the Preemptive Raw Socket serial protocol configuration settings.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.5.1.1.1
rcPreemptRSPackChar
The character that can be used to force forwarding of accumulated
data to the network.

If a packetization character is not configured - object is set to the
value of '256', accumulated data will be forw…
Integer32r/w
Constraints:
range: 0-256
 .1.3.6.1.4.1.15004.4.6.5.1.1.2
rcPreemptRSPackTimer
The delay in milliseconds from the last received character until
when data is forwarded.
millisecondsInteger32r/w
Constraints:
range: 3-1000
 .1.3.6.1.4.1.15004.4.6.5.1.1.3
rcPreemptRSPackSize
The Maximum number of bytes received from serial port to be packed
in one IP packet.
bytesInteger32r/w
Constraints:
range: 64-1400
 .1.3.6.1.4.1.15004.4.6.5.1.1.4
rcPreemptRSFlowControl
The type of FlowControl to be used on the port.
RcFlowControlr/w
Textual Convention: RcFlowControl Enumeration
Type Values:
1none
2xonXoff
 .1.3.6.1.4.1.15004.4.6.5.1.1.5
rcPreemptRSLocPort
The local IP port to listen to an incoming TCP connection or UDP
datagrams.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.5.1.1.6
rcPreemptRSRemPort
The remote TCP port to use when placing an outgoing connection.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.5.1.1.7
rcPreemptRSIpAdd
Defines the IpAddress based on the following:
- For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)'
this is the remote IP address to communicate with.
- For incoming TCP connection (server), 'rcRawSoc…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.15004.4.6.5.1.1.8
rcPreemptRSLinkStats
Enables links statistics collection.
EnabledStatusr/w
Textual Convention: EnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.15004.4.6.5.1.1.9
rcPreemptRSDynPackChar
The character that can be used to force forwarding of accumulated data
to the network for connection to dynamic master.

If a packetization character is not configured, accumulated data will
be forwarde…
Integer32r/w
Constraints:
range: 0-256
 .1.3.6.1.4.1.15004.4.6.5.1.1.10
rcPreemptRSDynPackTimer
The delay in milliseconds from the last received character until when
data is forwarded to the dynamic master.
millisecondsInteger32r/w
Constraints:
range: 3-1000
 .1.3.6.1.4.1.15004.4.6.5.1.1.11
rcPreemptRSDynTimeout
The time in seconds that is allowed to dynamic master to be idle
before it's connection is closed.
The protocol listens to the socket open to dymamic master, and if
no data are received within this time, conneciton w…
secondsInteger32r/w
Constraints:
range: 10-3600
 .1.3.6.1.4.1.15004.4.6.5.1.1.12

rcDnpRsTable

table
.1.3.6.1.4.1.15004.4.6.9.1 · 1 row entry · 8 columns
Open in standard view 
This table represents the set of parameters provide the ability to 
configure DNP over RawSocket protocol settings for serial ports. 
If no ports appear, then the DNP over RawSocket protocol must first be 
assigned to port(s)
rcDnpRsEntry entry .1.3.6.1.4.1.15004.4.6.9.1.1
List of ports with configuration parameters for DNP over RawSocket
serial protocol .
Indexes
rcDnpRsPort
Column Syntax OID
rcDnpRsPort
The physical Serial Port Number for which this Entry contains DNP over
Raw Socket serial protocol configuration settings.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.9.1.1.1
rcDnpRsCalllDir
Defines following:
- whether to accept an incoming connection 'in(0)' or
- to place an outgoing connection 'out(1)' or
- to place an outgoing connection and wait for incomming 'both(2)'

Note: This pa…
RcCallDirr/w
Textual Convention: RcCallDir Enumeration
Type Values:
0in
1out
2both
 .1.3.6.1.4.1.15004.4.6.9.1.1.2
rcDnpRsTransport
A transport protocol used for IP traffic for DNPRS on this port.
RcTransportr/w
Textual Convention: RcTransport Enumeration
Type Values:
1udp
2tcp
 .1.3.6.1.4.1.15004.4.6.9.1.1.3
rcDnpRsMaxConns
The maximum number of allowed incoming TCP connections.
Integer32r/w
Constraints:
range: 1-64
 .1.3.6.1.4.1.15004.4.6.9.1.1.4
rcDnpRsLocPort
The local IP port to listen to an incoming TCP connection or UDP
datagrams.
Integer32r/w
Constraints:
range: 1024-65535
 .1.3.6.1.4.1.15004.4.6.9.1.1.5
rcDnpRsRemPort
The remote TCP port to use when placing an outgoing connection.
Integer32r/w
Constraints:
range: 1024-65535
 .1.3.6.1.4.1.15004.4.6.9.1.1.6
rcDnpRsIpAdd
Defines the IpAddress based on the following:
- For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)'
this is the remote IP address to communicate with.
- For incoming TCP connection (server), 'rcRawSoc…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.15004.4.6.9.1.1.7
rcDnpRsLinkStats
Enables links statistics collection.
EnabledStatusr/w
Textual Convention: EnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.15004.4.6.9.1.1.8

rcMirrBitsTable

table
.1.3.6.1.4.1.15004.4.6.10.1 · 1 row entry · 6 columns
Open in standard view 
This table presents the list of ports with configuration options for 
configuring the Mirrirod Bits serial protocol on RuggedCom serial 
devices
rcMirrBitsEntry entry .1.3.6.1.4.1.15004.4.6.10.1.1
List of configuration options for all the ports configured for
Mirrored Bits serial protocol.
Indexes
rcMirrBitsPort
Column Syntax OID
rcMirrBitsPort
The physical Serial Port Number for which this Entry contains the
Mirrored Bits serial protocol configuration settings.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.10.1.1.1
rcMirrBitsTransport
A transport protocol used for IP traffic for MorroredBits on this
port.

This object is always set to the value of 'udp(2)'.
RcTransportr/w
Textual Convention: RcTransport Enumeration
Type Values:
1udp
2tcp
 .1.3.6.1.4.1.15004.4.6.10.1.1.2
rcMirrBitsLocPort
The local IP port to listen to UDP datagrams.
Integer32r/w
Constraints:
range: 1024-65535
 .1.3.6.1.4.1.15004.4.6.10.1.1.3
rcMirrBitsRemPort
The Remote port to which protocol on this port can exchange UDP
datagrams.
Integer32r/w
Constraints:
range: 1024-65535
 .1.3.6.1.4.1.15004.4.6.10.1.1.4
rcMirrBitsIpAdd
The IP Address of interface to listen to UDP datagrams.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.15004.4.6.10.1.1.5
rcMirrBitsLinkStats
Enables links statistics collection.
EnabledStatusr/w
Textual Convention: EnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.15004.4.6.10.1.1.6

rcTelnetComportTable

table
.1.3.6.1.4.1.15004.4.6.11.1 · 1 row entry · 10 columns
Open in standard view 
This table provides a list of port entries configured for TelnetPort 
Comport  serial protocolwith configuration options.
rcTelnetComportEntry entry .1.3.6.1.4.1.15004.4.6.11.1.1
List of ports with configuration options for TelnetPortComports serial
protocol.
Indexes
rcTelnetComportPort
Column Syntax OID
rcTelnetComportPort
Thephysical Serial Port Number for which this Entry contains the
TelnetPortComport serial protocol configuration settings.
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.15004.4.6.11.1.1.1
rcTelnetComportPackChar
The character that can be used to force forwarding of accumulated
data to the network.

If a packetization character is not configured - object is set to the
value of '256', accumulated data will be forw…
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.15004.4.6.11.1.1.2
rcTelnetComportPackTimer
The delay from the last received character until when data is
forwarded.
millisecondsInteger32r/w
Constraints:
range: 3-1000
 .1.3.6.1.4.1.15004.4.6.11.1.1.3
rcTelnetComportPackSize
The maximum number of bytes received from serial port to be packed
in one IP packet.
bytesInteger32r/w
Constraints:
range: 64-1400
 .1.3.6.1.4.1.15004.4.6.11.1.1.4
rcTelnetComportFlowControl
The type of FlowControl to be used on the port.
RcFlowControlr/w
Textual Convention: RcFlowControl Enumeration
Type Values:
1none
2xonXoff
 .1.3.6.1.4.1.15004.4.6.11.1.1.5
rcTelnetComportCallDir
Defines following:
- whether to accept an incoming connection 'in(0)' or
- to place an outgoing connection 'out(1)' or
- to place an outgoing connection and wait for incomming 'both(2)'.

This protocol…
RcCallDirr/w
Textual Convention: RcCallDir Enumeration
Type Values:
0in
1out
2both
 .1.3.6.1.4.1.15004.4.6.11.1.1.6
rcTelnetComportLocPort
The local IP port to listen to an incoming TCP connection.
Integer32r/w
Constraints:
range: 1024-65535
 .1.3.6.1.4.1.15004.4.6.11.1.1.7
rcTelnetComportRemPort
The remote TCP port to use when placing an outgoing connection.
Integer32r/w
Constraints:
range: 1024-65535
 .1.3.6.1.4.1.15004.4.6.11.1.1.8
rcTelnetComportIpAdd
Defines the IpAddress based on the following:
- For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)'
this is the remote IP address to communicate with.
- For incoming TCP connection (server), 'rcRawSoc…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.15004.4.6.11.1.1.9
rcTelnetComportLinkStats
Enables links statistics collection.
EnabledStatusr/w
Textual Convention: EnabledStatus Enumeration
Type Values:
1enabled
2disabled
 .1.3.6.1.4.1.15004.4.6.11.1.1.10

rcConnStatsTable

table
.1.3.6.1.4.1.15004.4.6.15.1 · 1 row entry · 5 columns
Open in standard view 
This table provides the statictics information for all active TCP 
connections on the RuggedCom serial device.
rcConnStatsEntry entry .1.3.6.1.4.1.15004.4.6.15.1.1
List of parameters providing the statictics information for all active TCP
connections on the RuggedCom serial device.
Indexes
rcConnStatsRemIp rcConnStatsRemPort rcConnStatsLocPort
Column Syntax OID
rcConnStatsRemIp
The remote IP address of the TCP connection.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.15004.4.6.15.1.1.1
rcConnStatsRemPort
The remote port number of the connection.
Integer32
Constraints:
range: 1024-65535
 .1.3.6.1.4.1.15004.4.6.15.1.1.2
rcConnStatsLocPort
The local port number of the connection.
Integer32
Constraints:
range: 1024-65535
 .1.3.6.1.4.1.15004.4.6.15.1.1.3
rcConnStatsRxPkts
The number of received packets.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.15004.4.6.15.1.1.4
rcConnStatsTxPkts
The number of transmitted packets.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.15004.4.6.15.1.1.5