Module Cold Start - a module has been plugged into a chassis

Module Power Applied - A power supply's cord was not supplying power
and now it is.  The supply is generating voltage.  (for chassis with
multiple supplies)

Remote Unit Lost.

Remote Unit Error Detected.

Remote Unit Good Detected.

The external clock source has been lost.

Serial Session Started.

Serial Session Stopped.

SFP is consuming too much power.

Remote Test Activation - test mode entered on remote device.

Remote Test Deactivation - test mode exited on remote device.

Local Test Activation - test mode entered on local device.

Data Manager Authentication Failure - The name and password supplied to
the SNMP agent did not match the ones configured into the data
manager's user-settings.

Local Test Deactivation - test mode exited on local device.

SSH Authentication Failure - Authentication type/password did not match
configured setting.

SSH Session Started - The management module has detected that a SSH
session has started.

SSH Session Stopped - The management module has detected that a SSH
session has stopped.

Configuration File Corrupted - The management module has detected a
corrupted configuration file.

Protection Switch - trap generated when a protection switch occurs.

Protection Configuration Mismatch - trap generated when a protection
configuration mismatch occurs.

Fan Rotation Not Detected - Detected no or low RPMs generated from the
fan.

Fan Rotation High Threshold - Detected fan rotation speed is high.

FPGA Failure - FPGA initialization failure.

Fan Rotation Normal - Detected normal fan rotation speed

1588 Synchronization - Synchronization with 1588 master is gained

1588 Synchronization - Synchronization with 1588 master is lost

1588 Master - Primary Master is Active

1588 Master - Primary Master Inactive

1588 Master - Secondary Master Active

1588 Master - Secondary Master Inactive

Synchronous Ethernet - Synchronous Ethernet Clock Source Gained

Synchronous Ethernet - Synchronous Ethernet Clock Source Lost

Synchronous Ethernet - Synchronous Ethernet Clock Holdover Lost

Chassis New - a new chassis has been added to the system

AIS State Change - OAM AIS reception or transmission state has changed

LCK State Change - OAM ETH-LCK  reception or transmission state has
changed

Threshold Crossing - Performance Criteria Measurement not met. This
trap should be generated at most once every 5 minutes.

Threshold Crossing - Performance Criteria Measurement met

TDM Clock Status Change - Status of TDM recovery clock changed

TDM Ethernet Frame Count - Incorrect number of Ethernet frames

SFP/XFP Receive CDR Loss of Lock

SFP/XFP transmitted loses CDR lock

DPoE Stage warning alarm. Alarm is sent when the alarm state changes to
either set or clear. Only one stage warning alarm can be set at one
time.

DPoE Stage failure alarm. Alarm is sent when the alarm state changes to
either set or clear.  Only one stage fail alarm can be set at one time.

Chassis Gone - a chassis has been removed from the system

SFP/XFP receiver gained CDR lock

SFP/XFP transmitted gained CDR lock

Module normal temperature

Module normal voltage range

Module data detected

802.3ah remote link normal

802.3ah local link normal

XFP/SFP normal

PoE PD Status Change

Generated when a Y.1731 probe priority changes.
          
Currently this is only valid for DMR reception.
          
'trapcode' indicates the probe instance number.

FTP Authentication Failure - Authentication type/password did not match
configured setting.

ACL denial. Access is not allowed by configured ACL's. This trap
only to be generated at most once a minute.

The module has detected Link OAM discovery completion on a port and is
generated when discovery completes.

The module has detected Link OAM discovery has been lost on a port and
is generated when a Link OAM discovery had previously been completed on
a port, but is now lost.

The module has initiated a Service Activation Test: either a 2544 or
ITU-T Y.1564 test.

The module has completed a Service Activation Test: either a 2544 or
ITU-T Y.1564 test.

The module has detected a utilization threshold violation on a port or
a bandwidth profile. trapcode of 1-99 indicate a port threshold
violation. trapcode of 101-164 indicate the bandwidth profile number
          
This trap can only be generated if the threshold has not been
violated for 5 seconds.

The module has detected a utilization threshold violation has cleared
on a port or a bandwidth profile number.
          
This trap can only be generated once a threshold violation has been
cleared for 5 seconds.

The module has detected loop condition and a loop prevention block on
the port has occurred.

The module has detected that a loop condition has been cleared and
the loop prevention block on the port has been removed.

Module Remove - a module has been removed from chassis

Telnet Authentication Failure - Telnet user name and/or password did not
match.

The module has detected a Ring Protection port state change.

Primary Link up

Primary Link down

Secondary Link up

Module Reset - the module received a reset command from the chassis
data manager

Secondary Link down

Telnet Session Started

Telnet Session Stopped

FTP Session Started

FTP Session Stopped

Secondary Link Standby Up

Secondary Link Standby Down

Password Count Exceeded

Flash checksum error

Flash file type incorrect

Module Link Down - the module went from a link to a no link condition

Flash program failure

Flash file transmission error

Module programming completed OK

Power failure detected, system shutting down

Periodic trap to let management applications know device is still
active

Module VLAN information has been changed

AIS Detected

PRBS Detected

Management module has acquired mastership of the backplane

Module Link Up - the module went from no link to a link condition

Module has switched secure mode
trapcode 0: secure -> normal (NMM master)
trapcode 1: normal -> secure (NMM master)
trapcode 2: secure -> normal (secure proxy)
trapcode 3: normal -> secure (secure proxy)
trapcode 4: secure -> normal (secure slave)
trapcode 5: normal -> secure (secure slave)

Management module has relinquished mastership of the backplane

A SFP Device Inserted

A SFP Device Removed

AH Link Event has been generated

AH Link Event has been received

Contact closure status change detected

A link fault has been received over AH connection

A critical event has been generated

A critical event has been received

Module Dip Switch Change - the dip switches on the module were changed

Power failure detected from remote partner, system shutting down

Generated when an internal resource is fully allocated.  Specific
resource is defined by the Trap code.

Generated when the  T1/E1, T3/E3 remote module responds to a loopback
request

Generated when the T1/E1, T3/E3 remote module stops sending a loopback
reply

Generated when an 802.1ag MEP has a persistent defect condition,
trapcode has the port number

Generated when an 802.1ag loopback command has completed.

Generated when an 802.1ag Link Trace command has completed.

Generated when an 802.1ag MEP is discovered, service is restored, or
status of report port changes.

Generated when an 802.1ag MEP timeout occurs.

Generated when an 802.1ag service ID does not match the VLAN or is at
a lower MD level.

Module Configuration Change - the module configuration was changed by
external software and the hardware configuration may no longer
reflect its true state

Generated when an 802.1ag MEP receives its own CCM or MEPID.

Generated when an 802.1ag MEP receives an incorrect CCM.

Generated when all 802.1ag expected MEPs are up in time.

Generated when an 802.1ag CCM is received from an unexpected MEP.

Module Over Temperature - for modules with temperature sensing
capabilities this trap indicates the temperature is over the acceptable
limits for the module

Generated when the measured Tx power is less than the low threshold.

Generated when the measured Tx power is greater than the high
threshold.

Generated when the measured bias voltage is less than the low
threshold.

Generated when the measured bias voltage is greater than the high
threshold.

Generated when the measured voltage is less than the low threshold.

Generated when the measured voltage is greater than the high threshold.

Generated when the measured temperature is less than the low threshold.

Module Voltage Range - for modules with voltage sensing capabilities
this trap indicates the voltage is outside of the acceptable limits
defined for the voltage being sensed

Generated when the measured temperature is greater than the high
threshold.

Generated when the measured Aux 2 value is less than the low threshold.

Generated when the measured Aux 2 value is greater than the high
threshold.

Generated when the measured Aux 1 value is less than the low threshold.

Generated when the measured Aux 1 value is greater than the high
threshold.

Generated when the measured Rx power is less than the low threshold.

Generated when the measured Rx power is greater than the high
threshold.

Generated when the measured voltage is less than the low threshold.

Generated when the measured voltage is greater than the high threshold.

Generated when the measured voltage is less than the low threshold.

Module Power Removed - A power supply's cord is no longer supplying
power to it and the supply is no longer generating voltage. (For
chassis with multiple supplies)

Generated when the measured voltage is greater than the high threshold.

OST equivalent of the DS1 MIB dsx1LineStatusChange.

Configuration change has been committed to flash.

Loopback Activation - loopback mode entered on remote device.

Loopback Deactivation - normal mode entered on remote device.

Timing Error or Clock Slip.

Data Framing Overrun.

Data Framing Under run.

Remote Unit Found.

Module Hardware Failure