DES6500-SWL2MGMT-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view

Tables

Rows

Columns

swL2PortCtrlTable

table

.1.3.6.1.4.1.171.11.78.1.2.3.2 · 1 row entry · 6 columns

Open in standard view

A table that contains control information about every port.

swL2PortCtrlEntry entry .1.3.6.1.4.1.171.11.78.1.2.3.2.1

A list of control information for each port of the device.

Indexes

swL2PortCtrlPortIndex

Column Syntax OID

swL2PortCtrlPortIndex

This object indicates the module's port number.(1..Max port
number in the module)

Integer32

Constraints:
range: 0-65535

.1.3.6.1.4.1.171.11.78.1.2.3.2.1.1

swL2PortCtrlUnitIndex

Indicates ID of the unit in the device

Integer32

Constraints:
range: 0-65535

.1.3.6.1.4.1.171.11.78.1.2.3.2.1.2

swL2PortCtrlAdminState

This object decide the port enabled or disabled.

Enumerationr/w

Enumerated Values:

1	other
2	disabled
3	enabled

.1.3.6.1.4.1.171.11.78.1.2.3.2.1.3

swL2PortCtrlNwayState

Chose the port speed, duplex mode, and N-Way function mode.

Enumerationr/w

Enumerated Values:

1	other
2	nway-enabled
3	nway-disabled-10Mbps-Half
4	nway-disabled-10Mbps-Full
5	nway-disabled-100Mbps-Half
6	nway-disabled-100Mbps-Full
7	nway-disabled-1Gigabps-Half
8	nway-disabled-1Gigabps-Full-none
9	nway-disabled-1Gigabps-Full-master
10	nway-disabled-1Gigabps-Full-slave

.1.3.6.1.4.1.171.11.78.1.2.3.2.1.4

swL2PortCtrlFlowCtrlState

The flow control mechanism is different between full duplex
mode and half duplex mode. For half duplex mode, the jamming
signal is asserted. For full duplex mode, IEEE 802.3x flow
control function sends PAUSE frames a…

Enumerationr/w

Enumerated Values:

1	other
2	disabled
3	enabled

.1.3.6.1.4.1.171.11.78.1.2.3.2.1.5

swL2PortCtrlLockState

This object decide the port is locked or not.

Enumerationr/w

Enumerated Values:

1	other
2	disabled
3	enabled

.1.3.6.1.4.1.171.11.78.1.2.3.2.1.6

swL2QOSBandwidthControlTable

table

.1.3.6.1.4.1.171.11.78.1.2.6.1 · 1 row entry · 3 columns

Open in standard view

swL2QOSBandwidthControlEntry entry .1.3.6.1.4.1.171.11.78.1.2.6.1.1

A list of information contained in swL2QOSBandwidthControlTable.

Indexes

swL2QOSBandwidthPortIndex

Column	Syntax	OID
swL2QOSBandwidthPortIndex Indicates the port .	Integer32 Constraints: `range: 1-768`	`.1.3.6.1.4.1.171.11.78.1.2.6.1.1.1`
swL2QOSBandwidthRxRate Indicates RX Rate(Mbit/sec) of the specifed port. Value 1000 means no limit. Value 10000 means no limit for 10G port.	Integer32r/w Constraints: `range: 1-10000`	`.1.3.6.1.4.1.171.11.78.1.2.6.1.1.2`
swL2QOSBandwidthTxRate Indicates TX Rate(Mbit/sec) of the specifed port. Value 1000 means no limit. Value 10000 means no limit for 10G port.	Integer32r/w Constraints: `range: 1-10000`	`.1.3.6.1.4.1.171.11.78.1.2.6.1.1.3`

swL2QOSSchedulingTable

table

.1.3.6.1.4.1.171.11.78.1.2.6.2 · 1 row entry · 3 columns

Open in standard view

swL2QOSSchedulingEntry entry .1.3.6.1.4.1.171.11.78.1.2.6.2.1

A list of information contained in swL2QOSSchedulingTable.

Indexes

swL2QOSSchedulingClassIndex

Column Syntax OID

swL2QOSSchedulingClassIndex

Indicates the hardware queue number.

Integer32

Constraints:
range: 0-7

.1.3.6.1.4.1.171.11.78.1.2.6.2.1.1

swL2QOSSchedulingMaxPkts

Indicates the maximum number of packets the hardware priority queue will be allowed
to transmit before allowing the next lowest priority queue to transmit its packets.
a value between 0 and 15 can be specified.

Integer32r/w

Constraints:
range: 0-15

.1.3.6.1.4.1.171.11.78.1.2.6.2.1.2

swL2QOSSchedulingMechanism

Indicates the mechanism of QOS scheduling.

Enumeration

Enumerated Values:

1	strict
2	roundrobin
3	weightfair

.1.3.6.1.4.1.171.11.78.1.2.6.2.1.3

swL2QOS8021pUserPriorityTable

table

.1.3.6.1.4.1.171.11.78.1.2.6.3 · 1 row entry · 2 columns

Open in standard view

swL2QOS8021pUserPriorityEntry entry .1.3.6.1.4.1.171.11.78.1.2.6.3.1

A list of information contained in swL2QOS8021pUserPriorityTable.

Indexes

swL2QOS8021pUserPriorityIndex

Column	Syntax	OID
swL2QOS8021pUserPriorityIndex The 802.1p user priority .	Integer32 Constraints: `range: 0-7`	`.1.3.6.1.4.1.171.11.78.1.2.6.3.1.1`
swL2QOS8021pUserPriorityClass The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).	Integer32r/w Constraints: `range: 0-6`	`.1.3.6.1.4.1.171.11.78.1.2.6.3.1.2`

swL2QOS8021pDefaultPriorityTable

table

.1.3.6.1.4.1.171.11.78.1.2.6.4 · 1 row entry · 2 columns

Open in standard view

swL2QOS8021pDefaultPriorityEntry entry .1.3.6.1.4.1.171.11.78.1.2.6.4.1

A list of information contained in swL2QOS8021pDefaultPriorityTable.

Indexes

swL2QOS8021pDefaultPriorityIndex

Column	Syntax	OID
swL2QOS8021pDefaultPriorityIndex Indicates the port number .	Integer32 Constraints: `range: 1-768`	`.1.3.6.1.4.1.171.11.78.1.2.6.4.1.1`
swL2QOS8021pDefaultPriority The priority value to assign to untagged packets received by the switch ports on the switch..	Integer32r/w Constraints: `range: 0-7`	`.1.3.6.1.4.1.171.11.78.1.2.6.4.1.2`

swL2PortSecurityControlTable

table

.1.3.6.1.4.1.171.11.78.1.2.7.1 · 1 row entry · 4 columns

Open in standard view

port security feature which controls the address leaning capability and the
traffic forwarding decision. Each port can have this function enabled or disabled.
When it is enabled and a number is given said N, which allows N addresses to be
learned at this port, the first N learned addresses are locked at this port as
static entry. When the learned addresses number reach N, any coming packet with
not learned source addresses are discarded (e.g. dropped) and no more new addresses
can be learned at this port.

swL2PortSecurityControlEntry entry .1.3.6.1.4.1.171.11.78.1.2.7.1.1

A list of information contained in swL2PortSecurityControlTable.

Indexes

swL2PortSecurityPortIndex

Column Syntax OID

swL2PortSecurityPortIndex

Indicates the secured port to lock address learning.

Integer32

Constraints:
range: 1-768

.1.3.6.1.4.1.171.11.78.1.2.7.1.1.1

swL2PortSecurityMaxLernAddr

Indicates allowable number of addresses to be learned at this port.

Integer32r/w

Constraints:
range: 0-64

.1.3.6.1.4.1.171.11.78.1.2.7.1.1.2

swL2PortSecurityMode

Indicates the mode of locking address.
In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer
expire. In this mode, when the locked address is aged
…

Enumerationr/w

Enumerated Values:

1	other
2	permanent
3	deleteOnTimeout
4	deleteOnReset

.1.3.6.1.4.1.171.11.78.1.2.7.1.1.3

swL2PortSecurityAdmState

Indicates administration state of locking address.

Enumerationr/w

Enumerated Values:

1	other
2	enable
3	disable

.1.3.6.1.4.1.171.11.78.1.2.7.1.1.4

swL2TrunkCtrlTable

table

.1.3.6.1.4.1.171.11.78.1.2.9.3 · 1 row entry · 7 columns

Open in standard view

This table specifys which ports group a set of ports(up to 8)
into a single logical link.

swL2TrunkCtrlEntry entry .1.3.6.1.4.1.171.11.78.1.2.9.3.1

A list of information specifies which ports group a set of
ports(up to 8) into a single logical link.

Indexes

swL2TrunkIndex

Column Syntax OID

swL2TrunkIndex

The index of logical port trunk. The trunk group number depend
on the existence of unit and module.

Integer32

Constraints:
range: 0-65535

.1.3.6.1.4.1.171.11.78.1.2.9.3.1.1

swL2TrunkName

The name of logical port trunk.

OctetStringr/w

Constraints:
range: 0-12

.1.3.6.1.4.1.171.11.78.1.2.9.3.1.2

swL2TrunkMasterPort

The object indicates the master port number of the port trunk
entry. When using Port Trunk, you can not configure the other
ports of the group except the master port.
Their configuration must be same as the master port…

Integer32r/w

Constraints:
range: 1-65535

.1.3.6.1.4.1.171.11.78.1.2.9.3.1.3

swL2TrunkMember

Indicate how many number of ports is included in this Trunk.
The trunk port number depend on the existence of module.
The maximum number of ports is 8 for one trunks.

PortListr/w

Textual Convention: PortList OctetString

Type Constraints:
range: 0..127

.1.3.6.1.4.1.171.11.78.1.2.9.3.1.4

swL2TrunkFloodingPort

The object indicates the flooding port number of the port trunk
entry. The first port of the trunk is implicitly configured to
be the flooding port.

Integer32

Constraints:
range: 1-65535

.1.3.6.1.4.1.171.11.78.1.2.9.3.1.5

swL2TrunkType

This object indicated that type of the trunk group.
static : is static trunk group
lacp : is LACP trunk group .

Enumerationr/w

Enumerated Values:

1	other
2	static
3	lacp

.1.3.6.1.4.1.171.11.78.1.2.9.3.1.6

swL2TrunkState

This object indicates the status of this entry.

SNMPv2-TCRowStatusr/w

Textual Convention: SNMPv2-TCRowStatus Enumeration

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

.1.3.6.1.4.1.171.11.78.1.2.9.3.1.7

swL2TrunkLACPPortTable

table

.1.3.6.1.4.1.171.11.78.1.2.9.5 · 1 row entry · 2 columns

Open in standard view

This table specifys which ports group a set of ports(up to 8)
into a single logical link.

swL2TrunkLACPPortEntry entry .1.3.6.1.4.1.171.11.78.1.2.9.5.1

A list of information specifies which ports group a set of
ports(up to 8) into a single logical link.

Indexes

swL2TrunkLACPPortIndex

Column Syntax OID

swL2TrunkLACPPortIndex

The index of logical port lacp.

Integer32

Constraints:
range: 0-65535

.1.3.6.1.4.1.171.11.78.1.2.9.5.1.1

swL2TrunkLACPPortState

The state of logical port lacp.

Enumerationr/w

Enumerated Values:

1	active
2	passive

.1.3.6.1.4.1.171.11.78.1.2.9.5.1.2

swL2IGMPSnoopingCtrlTable

table

.1.3.6.1.4.1.171.11.78.1.2.11.3 · 1 row entry · 11 columns

Open in standard view

The table controls the Vlan's IGMP function. Its scale depends
on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled
mode, there is only one entry in the table, with index 1. If 
VLAN is in Port-Base or 802.1q mode, the number of entries can 
be up to 12, with index range from 1 to 12.

swL2IGMPSnoopingCtrlEntry entry .1.3.6.1.4.1.171.11.78.1.2.11.3.1

The entry in IGMP control table (swL2IGMPSnoopingCtrlTable). The entry
is effective only when IGMP capture switch
(swL2DevCtrlIGMPSnooping) is enabled.

Indexes

swL2IGMPSnoopingCtrlVid

Column Syntax OID

swL2IGMPSnoopingCtrlVid

This object indicates the IGMP control entry's VLAN id. If VLAN
is disabled, the Vid is always 0 and cannot be changed by
management users. If VLAN is in Port-Base mode, the Vid is
arranged from 1 to 12, fixed form. If …

Integer32

Constraints:
range: 0-65535

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.1

swL2IGMPSnoopingQueryInterval

The frequency at which IGMP Host-Query packets are
transmitted on this switch.

Integer32r/w

Constraints:
range: 1-65535

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.2

swL2IGMPSnoopingMaxResponseTime

The maximum query response time on this switch.

Integer32r/w

Constraints:
range: 1-25

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.3

swL2IGMPSnoopingRobustness

The Robustness Variable allows tuning for the expected
packet loss on a subnet. If a subnet is expected to be
lossy, the Robustness Variable may be increased. IGMP is
robust to (Robustness Variable-1) packet losses.

Integer32r/w

Constraints:
range: 1-255

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.4

swL2IGMPSnoopingLastMemberQueryInterval

The Last Member Query Interval is the Max Response Time
inserted into Group-Specific Queries sent in response to
Leave Group messages, and is also the amount of time between
Group-Specific Query messages.

Integer32r/w

Constraints:
range: 1-25

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.5

swL2IGMPSnoopingHostTimeout

The timer value for sending IGMP query packet when none was
sent by the host in the LAN. The timer works in per-VLAN basis.
Our device will be activated to send the query message if the
timer is expired. Please refere…

Integer32r/w

Constraints:
range: 1-16711450

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.6

swL2IGMPSnoopingRouteTimeout

The Router Timeout is how long a host must wait after hearing
a Query before it may send any IGMPv2 messages.

Integer32r/w

Constraints:
range: 1-16711450

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.7

swL2IGMPSnoopingLeaveTimer

When a querier receives a Leave Group message for a group that
has group members on the reception interface, it sends
Group-Specific Queries every swL2IGMPLeaveTimer to the group
being left.

Integer32r/w

Constraints:
range: 1-16711450

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.8

swL2IGMPSnoopingQueryState

This object decide the IGMP query enabled or disabled.

Enumerationr/w

Enumerated Values:

1	other
2	disabled
3	enabled

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.9

swL2IGMPSnoopingCurrentState

This object indicates the current IGMP query state.

Enumeration

Enumerated Values:

1	other
2	querier
3	non-querier

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.10

swL2IGMPSnoopingCtrlState

This object indicates the status of this entry.

other(1) - this entry is currently in use but the conditions under
which it will remain so are different from each of the following
values.
disable(…

Enumerationr/w

Enumerated Values:

1	other
2	disable
3	enable

.1.3.6.1.4.1.171.11.78.1.2.11.3.1.11

swL2IGMPSnoopingQueryInfoTable

table

.1.3.6.1.4.1.171.11.78.1.2.11.4 · 1 row entry · 3 columns

Open in standard view

The table contains the number current IGMP query packets which
is captured by this device, as well as the IGMP query packets
sent by the device.

swL2IGMPSnoopingQueryInfoEntry entry .1.3.6.1.4.1.171.11.78.1.2.11.4.1

Information about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPSnoopingCtrState of associated VLAN
entry are all enabled.

Indexes

swL2IGMPSnoopingInfoVid

Column	Syntax	OID
swL2IGMPSnoopingInfoVid This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPSnoopingCtrlVid in the associated entry of IGMP control table (swL2IGMPSnoopingCtrlTable).	Integer32 Constraints: `range: 0-65535`	`.1.3.6.1.4.1.171.11.78.1.2.11.4.1.1`
swL2IGMPSnoopingInfoQueryCount This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.	Integer32 Constraints: `range: 0-65535`	`.1.3.6.1.4.1.171.11.78.1.2.11.4.1.2`
swL2IGMPSnoopingInfoTxQueryCount This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.	Integer32 Constraints: `range: 0-65535`	`.1.3.6.1.4.1.171.11.78.1.2.11.4.1.3`

swL2IGMPSnoopingInfoTable

table

.1.3.6.1.4.1.171.11.78.1.2.11.5 · 1 row entry · 5 columns

Open in standard view

The table containing current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. Note
that the priority of IGMP table entries is lower than Filtering
Table, i.e. if there is a table hash collision between the 
entries of IGMP Table and Filtering Table inside the switch H/W
address table, then Filtering Table entry overwrite the 
colliding entry of IGMP Table. See swL2FilterMgmt description 
also.

swL2IGMPSnoopingInfoEntry entry .1.3.6.1.4.1.171.11.78.1.2.11.5.1

Information about current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnoopingSnooping and
swL2IGMPSnoopingCtrlState of associated VLAN entry are all enabled.

Indexes

swL2IGMPSnoopingVid swL2IGMPSnoopingGroupIpAddr

Column	Syntax	OID
swL2IGMPSnoopingVid This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.	Integer32 Constraints: `range: 0-65535`	`.1.3.6.1.4.1.171.11.78.1.2.11.5.1.1`
swL2IGMPSnoopingGroupIpAddr This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.	SNMPv2-SMIIpAddress Textual Convention: SNMPv2-SMIIpAddress `OctetString` Type Constraints: `range: 4`	`.1.3.6.1.4.1.171.11.78.1.2.11.5.1.2`
swL2IGMPSnoopingMacAddr This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.	MacAddress Textual Convention: MacAddress `OctetString` Type Constraints: `range: 6`	`.1.3.6.1.4.1.171.11.78.1.2.11.5.1.3`
swL2IGMPSnoopingPortMap This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered p…	PortList Textual Convention: PortList `OctetString` Type Constraints: `range: 0..127`	`.1.3.6.1.4.1.171.11.78.1.2.11.5.1.4`
swL2IGMPSnoopingIpGroupReportCount This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.	Integer32 Constraints: `range: 0-65535`	`.1.3.6.1.4.1.171.11.78.1.2.11.5.1.5`

swL2TrafficSegTable

table

.1.3.6.1.4.1.171.11.78.1.2.14.1 · 1 row entry · 2 columns

Open in standard view

This table specifys the port just can forward traffic to the 
specific port list.

swL2TrafficSegEntry entry .1.3.6.1.4.1.171.11.78.1.2.14.1.1

A list of information specifies the port with its traffic
forward list.

Indexes

swL2TrafficSegPort

Column	Syntax	OID
swL2TrafficSegPort The port number of the logical port.	Integer32 Constraints: `range: 0-65535`	`.1.3.6.1.4.1.171.11.78.1.2.14.1.1.1`
swL2TrafficSegForwardPorts The port list that the specific port can forward traffic.	PortListr/w Textual Convention: PortList `OctetString` Type Constraints: `range: 0..127`	`.1.3.6.1.4.1.171.11.78.1.2.14.1.1.2`