zhoneTacTestId

ZHONE-CARD-DIAGNOSTICS-MIB · .1.3.6.1.4.1.5504.3.3.7.1.4
MIB view Table view

Object

column r/w Enumeration 
This object is only valid for Tac Cards which
support the new Legerity Suite of tests.
              
This object identifies which test is to
be run, or can be set to abort the current test.
              
Test results are sent to the zhoneTacTestResultsTable.
              
There are 3 Legerity software packages: Basic Test (VCP-BT),
Advanced Test (VCP-AT), and Advanced Test Plus (VCP-ATP).
We currently support Basic Test package.
The following lists which tests are supported in each 
software package.
              
Calibration	VCP-ATP
Foreign DC Voltage Test	VCP-BT, VCP-AT, VCP-ATP
Foreign AC VoltageTest	VCP-BT, VCP-AT, VCP-ATP
DC Loop Resistance Test	VCP-BT, VCP-AT, VCP-ATP
Three-Element Insulation Resistance Test	VCP-BT, VCP-AT, VCP-ATP
Five-Element Insulation Resistance Test	VCP-ATP
Three-Element Capacitance Test	VCP-BT, VCP-AT
Receiver Off-Hook Test	VCP-BT, VCP-AT, VCP-ATP
Distance to Open Test 	VCP-BT, VCP-AT
Foreign AC Currents Test	VCP-BT, VCP-AT
Ringer Equivalency Number Test	VCP-BT, VCP-AT, VCP-ATP
DTMF and Pulse Digit Measurement Test	VCP-BT, VCP-AT
Noise Measurement Test	VCP-BT, VCP-AT, VCP-ATP
Signal to Noise Ratio Test	VCP-ATP
Arbitrary Single Tone Measurement Test	VCP-ATP
Tone Generation Test	VCP-BT, VCP-AT
Trans-Hybrid Loss Test	VCP-BT, VCP-AT, VCP-ATP
Draw and Break Dial Tone Test	VCP-BT, VCP-AT
Inward Current Test 	VCP-ATP
DC Feed Self-Test	VCP-BT, VCP-AT, VCP-ATP
On/Off Hook Self-Test	VCP-BT, VCP-AT, VCP-ATP
Ringing Self-Test 	VCP-BT, VCP-AT, VCP-ATP
Ringing Monitor Test	VCP-BT, VCP-AT, VCP-ATP
Metering Self-Test	VCP-BT, VCP-AT
Transmission Self-Test	VCP-BT, VCP-AT, VCP-ATP
Dialing Sef Test	VCP-BT, VCP-AT
Howler Test	VCP-BT, VCP-AT
Fuse Test	VCP-ATP
Read Loop and Battery Conditions	VCP-BT, VCP-AT, VCP-ATP

Context

MIB
ZHONE-CARD-DIAGNOSTICS-MIB
OID
.1.3.6.1.4.1.5504.3.3.7.1.4
Type
column
Access
readwrite
Status
current
Parent
zhoneTacTestEntry
Table
zhoneTacTestTable
Siblings
8

Syntax

Enumeration

Values & Constraints

Enumerated Values
1none
2runAllTests
3abortTest
4calibration
5foreignDCVoltage
6foreignACVoltage
7dcLoopResistance
8threeElementInsulationResistance
9fiveElementInsulationResistance
10threeElementCapacitance
11receiverOffHook
12distanceToOpen
13foreignACCurrents
14ringerEquivalencyNumber
15dtmfAndPulseDigitMeasurement
16noiseMeasurement
17signalToNoiseRatio
18arbitrarySignalToneMeasurement
19toneGeneration
20transHybridLoss
21drawAndBreakDialTone
22inwardCurrent
23dcFeedSelf
24onAndOffHookSelfTest
25ringingSelfTest
26ringingMonitor
27meteringSelfTest
28transmissionSelfTest
29dialingSelfTest
30howlerTest
31fuseTest
32readLoopAndBatteryConditions

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
zhoneTacIndex
This field is the index field for the tac test channel which will be connected on the external port. This device supports a maximum of two channels, one or both channels may be su…
columnInteger32.1.3.6.1.4.1.5504.3.3.7.1.1
zhoneTacInterfaceIndex
This field contains the InterfaceIndex of the physical line to be tested. If no line is currently being tested this value is 0. The ability of a physical line type …
columnIF-MIBInterfaceIndexOrZero.1.3.6.1.4.1.5504.3.3.7.1.2
zhoneTacTestMode
This field is used to set the mtac test mode for a given line. The options are: mtacModeBridge - All traffic on the given line is bridged across the mtac lines mtac…
columnEnumeration.1.3.6.1.4.1.5504.3.3.7.1.3
zhoneTacTestParam1
Optional Test Parameter #1
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.5504.3.3.7.1.5
zhoneTacTestParam2
Optional Test Paramerter #2
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.5504.3.3.7.1.6
zhoneTacTestParam3
Optional Test Parameter #3
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.5504.3.3.7.1.7
zhoneTacTestParam4
Optional Test Parameter #4
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.5504.3.3.7.1.8
zhoneTacTestParam5
Optional Test Parameter #5 Value: 0x00000001 Force Line-Test mode
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.5504.3.3.7.1.9