xdsl2LineCmndConfLdsf

VDSL2-LINE-MIB · .1.3.6.1.2.1.10.251.1.1.1.1.5
MIB view Table view

Object

column r/w VDSL2-LINE-TC-MIBXdsl2LineLdsf 
Loop diagnostic state forced (LDSF).
Defines whether the line should be forced into the loop
diagnostics mode by the near-end xTU of this line.  Note that
a loop diagnostic may be initiated by the far-end xTU at any
time.
              
Only when the xdsl2LineStatusPwrMngState object is in the
'l3' state and the xdsl2LineCmndConfPmsf object is in the
'l0orL2toL3' state, can the line be forced into loop diagnostic
mode procedures.  Upon successful completion of the loop
diagnostic mode procedures, the Access Node shall set this
object to 'inhibit', and xdsl2LineStatusPwrMngState will
remain in the 'l3' state.  The loop diagnostic data shall be
available at least until xdsl2LineCmndConfPmsf is set to the
'l3toL0' state.
              
The results of the loop diagnostic procedure are stored in the
tables xdsl2SCStatusTable, xdsl2SCStatusBandTable, and
xdsl2SCStatusSegmentTable.  The status of the loop diagnostic
procedure is indicated by xdsl2LineCmndConfLdsfFailReason.
              
As long as loop diagnostic procedures are not completed
successfully, attempts shall be made to do so, until the loop
diagnostic mode is no longer forced on the line through this
configuration parameter.

Context

MIB
VDSL2-LINE-MIB
OID
.1.3.6.1.2.1.10.251.1.1.1.1.5
Type
column
Access
readwrite
Status
current
Parent
xdsl2LineEntry
Table
xdsl2LineTable
Siblings
37

Syntax

VDSL2-LINE-TC-MIBXdsl2LineLdsf
Source
VDSL2-LINE-TC-MIBXdsl2LineLdsf
Base type
Enumeration

Values & Constraints

Type Values
0inhibit
1force

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
xdsl2LineConfTemplate
The value of this object identifies the row in the xDSL2 Line Configuration Template Table, xdsl2LineConfTemplateTable, that applies for this line. This object MUST…
columnOctetString.1.3.6.1.2.1.10.251.1.1.1.1.1
xdsl2LineCmndAutomodeColdStart
Automode cold start forced. This parameter is defined in order to improve testing of the performance of xTUs supporting automode when it is enabled in the MIB. Change the value o…
columnSNMPv2-TCTruthValue.1.3.6.1.2.1.10.251.1.1.1.1.10
xdsl2LineCmndConfReset
Request a line reset to occur. If this object is set to the value of 'reset', then force the line to reset (i.e., the modems will retrain). When the line has successfully reset, t…
columnVDSL2-LINE-TC-MIBXdsl2LineReset.1.3.6.1.2.1.10.251.1.1.1.1.11
xdsl2LineStatusActTemplate
This object is used to identify the template that is currently in use for this line. This object is updated when a successful line initialization occurs. This object indicates if …
columnOctetString.1.3.6.1.2.1.10.251.1.1.1.1.12
xdsl2LineStatusXtuTransSys
The xTU Transmission System (xTS) in use. It is coded in a bitmap representation with one bit set to '1' (the selected coding for the DSL line). This parameter may…
columnVDSL2-LINE-TC-MIBXdsl2TransmissionModeType.1.3.6.1.2.1.10.251.1.1.1.1.13
xdsl2LineStatusPwrMngState
The current power management state.
columnVDSL2-LINE-TC-MIBXdsl2PowerMngState.1.3.6.1.2.1.10.251.1.1.1.1.14
xdsl2LineStatusInitResult
Indicates the result of the last full initialization performed on the line.
columnVDSL2-LINE-TC-MIBXdsl2InitResult.1.3.6.1.2.1.10.251.1.1.1.1.15
xdsl2LineStatusLastStateDs
The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line.
columnVDSL2-LINE-TC-MIBXdsl2LastTransmittedState.1.3.6.1.2.1.10.251.1.1.1.1.16
xdsl2LineStatusLastStateUs
The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line.
columnVDSL2-LINE-TC-MIBXdsl2LastTransmittedState.1.3.6.1.2.1.10.251.1.1.1.1.17
xdsl2LineStatusXtur
Indicates the current state (existing failures) of the xTU-R. This is a bitmap of possible conditions.
columnVDSL2-LINE-TC-MIBXdsl2LineStatus.1.3.6.1.2.1.10.251.1.1.1.1.18
xdsl2LineStatusXtuc
Indicates the current state (existing failures) of the xTU-C. This is a bitmap of possible conditions.
columnVDSL2-LINE-TC-MIBXdsl2LineStatus.1.3.6.1.2.1.10.251.1.1.1.1.19
xdsl2LineConfFallbackTemplate
This object is used to identify the template that will be used if the xDSL2 line fails to operate using the primary template. The primary template is identified using the xdsl2Li…
columnOctetString.1.3.6.1.2.1.10.251.1.1.1.1.2
xdsl2LineStatusAttainableRateDs
Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the xTU-C transmitter and the xTU-R receiver, coded in bit/s.
columnbits/second SNMPv2-SMIUnsigned32.1.3.6.1.2.1.10.251.1.1.1.1.20
xdsl2LineStatusAttainableRateUs
Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the xTU-R transmitter and the xTU-C receiver, coded in bit/s.
columnbits/second SNMPv2-SMIUnsigned32.1.3.6.1.2.1.10.251.1.1.1.1.21
xdsl2LineStatusActPsdDs
Actual Power Spectral Density (PSD) Downstream. The average downstream transmit PSD over the subcarriers used for downstream. It ranges from -900 to 0 units of 0.1 dBm/Hz (physic…
column0.1 dBm/Hz Integer32.1.3.6.1.2.1.10.251.1.1.1.1.22
xdsl2LineStatusActPsdUs
Actual Power Spectral Density (PSD) Upstream. The average upstream transmit PSD over the subcarriers used for upstream. It ranges from -900 to 0 units of 0.1 dBm/Hz (physical val…
column0.1 dBm/Hz Integer32.1.3.6.1.2.1.10.251.1.1.1.1.23
xdsl2LineStatusActAtpDs
Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the xTU-C at the U-C reference point, at the instant of measurement. It ranges from -3…
column0.1 dBm Integer32.1.3.6.1.2.1.10.251.1.1.1.1.24
xdsl2LineStatusActAtpUs
Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the xTU-R at the U-R reference point, at the instant of measurement. It ranges from -310…
column0.1 dBm Integer32.1.3.6.1.2.1.10.251.1.1.1.1.25
xdsl2LineStatusActProfile
The G.993.2 profile in use. The configuration parameter xdsl2LConfProfProfiles defines the set of allowed G.993.2 profiles. This parameter indicates the profile in use on this li…
columnVDSL2-LINE-TC-MIBXdsl2LineProfiles.1.3.6.1.2.1.10.251.1.1.1.1.26
xdsl2LineStatusActLimitMask
The Limit PSD mask and band plan in use. The configuration parameter xdsl2LConfProfLimitMask defines the set of allowed G.993.2 limit PSD masks. This parameter indicates the limit…
columnVDSL2-LINE-TC-MIBXdsl2LineLimitMask.1.3.6.1.2.1.10.251.1.1.1.1.27
xdsl2LineStatusActUs0Mask
The US0 PSD mask in use. The configuration parameter xdsl2LConfProfUs0Mask defines the set of allowed US0 PSD masks. This parameter indicates the US0 PSD mask in use on this line.…
columnVDSL2-LINE-TC-MIBXdsl2LineUs0Mask.1.3.6.1.2.1.10.251.1.1.1.1.28
xdsl2LineStatusActSnrModeDs
This parameter indicates if the transmitter-referred virtual noise is active on the line in the downstream direction. The configuration parameter xdsl2LConfProfSnrModeDs is used t…
columnVDSL2-LINE-TC-MIBXdsl2LineSnrMode.1.3.6.1.2.1.10.251.1.1.1.1.29
xdsl2LineAlarmConfTemplate
The value of this object identifies the row in the xDSL2 Line Alarm Configuration Template Table, xdsl2LineAlarmConfTemplateTable, which applies to this line. This …
columnOctetString.1.3.6.1.2.1.10.251.1.1.1.1.3
xdsl2LineStatusActSnrModeUs
This parameter indicates if the transmitter-referred virtual noise is active on the line in the upstream direction. The configuration parameter xdsl2LConfProfSnrModeUs is used to …
columnVDSL2-LINE-TC-MIBXdsl2LineSnrMode.1.3.6.1.2.1.10.251.1.1.1.1.30
xdsl2LineStatusElectricalLength
This parameter contains the estimated electrical length expressed in dB at 1 MHz, kl0. This is the final electrical length that would have been sent from the VTU-O to VTU-R if th…
column0.1 dB Unsigned32.1.3.6.1.2.1.10.251.1.1.1.1.31
xdsl2LineStatusTssiDs
The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1 (Downstream).
columnVDSL2-LINE-TC-MIBXdsl2Tssi.1.3.6.1.2.1.10.251.1.1.1.1.32
xdsl2LineStatusTssiUs
The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1 (Upstream).
columnVDSL2-LINE-TC-MIBXdsl2Tssi.1.3.6.1.2.1.10.251.1.1.1.1.33
xdsl2LineStatusMrefPsdDs
The MEDLEY Reference PSD status parameters in the downstream direction expressed as the set of breakpoints exchanged at initialization.
columnVDSL2-LINE-TC-MIBXdsl2MrefPsdDs.1.3.6.1.2.1.10.251.1.1.1.1.34
xdsl2LineStatusMrefPsdUs
The MEDLEY Reference PSD status parameters in the upstream direction expressed as the set of breakpoints exchanged at initialization.
columnVDSL2-LINE-TC-MIBXdsl2MrefPsdUs.1.3.6.1.2.1.10.251.1.1.1.1.35
xdsl2LineStatusTrellisDs
This parameter reports whether trellis coding is in use in the downstream direction.
columnSNMPv2-TCTruthValue.1.3.6.1.2.1.10.251.1.1.1.1.36
xdsl2LineStatusTrellisUs
This parameter reports whether trellis coding is in use in the upstream direction.
columnSNMPv2-TCTruthValue.1.3.6.1.2.1.10.251.1.1.1.1.37
xdsl2LineStatusActualCe
(ACTUALCE) This parameter reports the cyclic extension used on the line. It is coded as an unsigned integer from 2 to 16 in units of N/32 samples, where 2N is the Inverse Discret…
columnN/32 samples Unsigned32.1.3.6.1.2.1.10.251.1.1.1.1.38
xdsl2LineCmndConfPmsf
Power management state forced (PMSF). Defines the line states to be forced by the near-end xTU on this line. This object MUST be maintained in a persistent manner.
columnVDSL2-LINE-TC-MIBXdsl2ConfPmsForce.1.3.6.1.2.1.10.251.1.1.1.1.4
xdsl2LineCmndConfLdsfFailReason
The status of the most recent occasion when the loop diagnostics state forced (LDSF) command was issued for the associated line.
columnVDSL2-LINE-TC-MIBXdsl2LdsfResult.1.3.6.1.2.1.10.251.1.1.1.1.6
xdsl2LineCmndConfBpsc
Request a bits-per-subcarrier measurement to be made. A request for a bits-per-subcarrier measurement is made by setting this object to the value of 'measure'. Upo…
columnVDSL2-LINE-TC-MIBXdsl2LineBpsc.1.3.6.1.2.1.10.251.1.1.1.1.7
xdsl2LineCmndConfBpscFailReason
The status of the most recent bits-per-subcarrier measurement request issued for the associated line.
columnVDSL2-LINE-TC-MIBXdsl2BpscResult.1.3.6.1.2.1.10.251.1.1.1.1.8
xdsl2LineCmndConfBpscRequests
Measurement request counter. This counter is incremented by one every time a request for a bits-per-subcarrier measurement is made. A measurement request is made b…
columnSNMPv2-SMICounter32.1.3.6.1.2.1.10.251.1.1.1.1.9