VDSL2-LINE-MIB Table View

The table xdsl2LineTable contains configuration, command and
status parameters of the VDSL2/ADSL/ADSL2 or ADSL2+ line.
          
Several objects in this table MUST be maintained in a persistent
manner.

xdsl2LineEntry row .1.3.6.1.2.1.10.251.1.1.1.1

The index of this table is an interface index where the
interface has an ifType of vdsl2(251).

Indexes

IF-MIBifIndex

Column	Syntax	OID
xdsl2LineConfTemplate The value of this object identifies the row in the xDSL2 Line Configuration Template Table, xdsl2LineConfTemplateTable, that applies for this line. This object MUST be maintained in a persistent manner.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.2.1.10.251.1.1.1.1.1
xdsl2LineConfFallbackTemplate This object is used to identify the template that will be used if the xDSL2 line fails to operate using the primary template. The primary template is identified using the xdsl2LineConfTemplate object. Fo…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.2.1.10.251.1.1.1.1.2
xdsl2LineAlarmConfTemplate The value of this object identifies the row in the xDSL2 Line Alarm Configuration Template Table, xdsl2LineAlarmConfTemplateTable, which applies to this line. This object MUST be maintained in a persisten…	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.2.1.10.251.1.1.1.1.3
xdsl2LineCmndConfPmsf Power management state forced (PMSF). Defines the line states to be forced by the near-end xTU on this line. This object MUST be maintained in a persistent manner.	VDSL2-LINE-TC-MIBXdsl2ConfPmsForcer/w Type Values: 0 l3toL0 2 l0toL2 3 l0orL2toL3	.1.3.6.1.2.1.10.251.1.1.1.1.4
xdsl2LineCmndConfLdsf Loop diagnostic state forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end xTU of this line. Note that a loop diagnostic may be initiated by the far-end xTU at any tim…	VDSL2-LINE-TC-MIBXdsl2LineLdsfr/w Type Values: 0 inhibit 1 force	.1.3.6.1.2.1.10.251.1.1.1.1.5
xdsl2LineCmndConfLdsfFailReason The status of the most recent occasion when the loop diagnostics state forced (LDSF) command was issued for the associated line.	VDSL2-LINE-TC-MIBXdsl2LdsfResult Type Values: 1 none 2 success 3 inProgress 4 unsupported 5 cannotRun 6 aborted 7 failed 8 illegalMode 9 adminUp 10 tableFull 11 noResources	.1.3.6.1.2.1.10.251.1.1.1.1.6
xdsl2LineCmndConfBpsc Request a bits-per-subcarrier measurement to be made. A request for a bits-per-subcarrier measurement is made by setting this object to the value of 'measure'. Upon completion of the measurement request,…	VDSL2-LINE-TC-MIBXdsl2LineBpscr/w Type Values: 1 idle 2 measure	.1.3.6.1.2.1.10.251.1.1.1.1.7
xdsl2LineCmndConfBpscFailReason The status of the most recent bits-per-subcarrier measurement request issued for the associated line.	VDSL2-LINE-TC-MIBXdsl2BpscResult Type Values: 1 none 2 success 3 inProgress 4 unsupported 5 failed 6 noResources	.1.3.6.1.2.1.10.251.1.1.1.1.8
xdsl2LineCmndConfBpscRequests Measurement request counter. This counter is incremented by one every time a request for a bits-per-subcarrier measurement is made. A measurement request is made by modifying the xdsl2LineCmndConfBpsc ob…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.1.1.1.9
xdsl2LineCmndAutomodeColdStart Automode cold start forced. This parameter is defined in order to improve testing of the performance of xTUs supporting automode when it is enabled in the MIB. Change the value of this parameter to 'true' to indicate a…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.251.1.1.1.1.10
xdsl2LineCmndConfReset Request a line reset to occur. If this object is set to the value of 'reset', then force the line to reset (i.e., the modems will retrain). When the line has successfully reset, the SNMP agent will set the value of this…	VDSL2-LINE-TC-MIBXdsl2LineResetr/w Type Values: 1 idle 2 reset	.1.3.6.1.2.1.10.251.1.1.1.1.11
xdsl2LineStatusActTemplate This object is used to identify the template that is currently in use for this line. This object is updated when a successful line initialization occurs. This object indicates if the primary template (xdsl2LineConfTempl…	OctetString Constraints: range: 0-32	.1.3.6.1.2.1.10.251.1.1.1.1.12
xdsl2LineStatusXtuTransSys The xTU Transmission System (xTS) in use. It is coded in a bitmap representation with one bit set to '1' (the selected coding for the DSL line). This parameter may be derived from the handshaking procedu…	VDSL2-LINE-TC-MIBXdsl2TransmissionModeType Type Values: 0 ansit1413 1 etsi 2 g9921PotsNonOverlapped 3 g9921PotsOverlapped 4 g9921IsdnNonOverlapped 5 g9921isdnOverlapped 6 g9921tcmIsdnNonOverlapped 7 g9921tcmIsdnOverlapped 8 g9922potsNonOverlapped 9 g9922potsOverlapped 10 g9922tcmIsdnNonOverlapped 11 g9922tcmIsdnOverlapped 12 g9921tcmIsdnSymmetric 13 reserved1 14 reserved2 15 reserved3 16 reserved4 17 reserved5 18 g9923PotsNonOverlapped 19 g9923PotsOverlapped 20 g9923IsdnNonOverlapped 21 g9923isdnOverlapped 22 reserved6 23 reserved7 24 g9924potsNonOverlapped 25 g9924potsOverlapped 26 reserved8 27 reserved9 28 g9923AnnexIAllDigNonOverlapped 29 g9923AnnexIAllDigOverlapped 30 g9923AnnexJAllDigNonOverlapped 31 g9923AnnexJAllDigOverlapped 32 g9924AnnexIAllDigNonOverlapped 33 g9924AnnexIAllDigOverlapped 34 g9923AnnexLMode1NonOverlapped 35 g9923AnnexLMode2NonOverlapped 36 g9923AnnexLMode3Overlapped 37 g9923AnnexLMode4Overlapped 38 g9923AnnexMPotsNonOverlapped 39 g9923AnnexMPotsOverlapped 40 g9925PotsNonOverlapped 41 g9925PotsOverlapped 42 g9925IsdnNonOverlapped 43 g9925isdnOverlapped 44 reserved10 45 reserved11 46 g9925AnnexIAllDigNonOverlapped 47 g9925AnnexIAllDigOverlapped 48 g9925AnnexJAllDigNonOverlapped 49 g9925AnnexJAllDigOverlapped 50 g9925AnnexMPotsNonOverlapped 51 g9925AnnexMPotsOverlapped 52 reserved12 53 reserved13 54 reserved14 55 reserved15 56 g9932AnnexA 57 g9932AnnexB 58 g9932AnnexC 59 reserved16 60 reserved17 61 reserved18 62 reserved19 63 reserved20	.1.3.6.1.2.1.10.251.1.1.1.1.13
xdsl2LineStatusPwrMngState The current power management state.	VDSL2-LINE-TC-MIBXdsl2PowerMngState Type Values: 1 l0 2 l1 3 l2 4 l3	.1.3.6.1.2.1.10.251.1.1.1.1.14
xdsl2LineStatusInitResult Indicates the result of the last full initialization performed on the line.	VDSL2-LINE-TC-MIBXdsl2InitResult Type Values: 0 noFail 1 configError 2 configNotFeasible 3 commFail 4 noPeerAtu 5 otherCause	.1.3.6.1.2.1.10.251.1.1.1.1.15
xdsl2LineStatusLastStateDs The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line.	VDSL2-LINE-TC-MIBXdsl2LastTransmittedState Type Values: 0 atucG9941 1 atucQuiet1 2 atucComb1 3 atucQuiet2 4 atucComb2 5 atucIcomb1 6 atucLineprob 7 atucQuiet3 8 atucComb3 9 atucIComb2 10 atucMsgfmt 11 atucMsgpcb 12 atucQuiet4 13 atucReverb1 14 atucTref1 15 atucReverb2 16 atucEct 17 atucReverb3 18 atucTref2 19 atucReverb4 20 atucSegue1 21 atucMsg1 22 atucReverb5 23 atucSegue2 24 atucMedley 25 atucExchmarker 26 atucMsg2 27 atucReverb6 28 atucSegue3 29 atucParams 30 atucReverb7 31 atucSegue4 32 atucShowtime 100 aturG9941 101 aturQuiet1 102 aturComb1 103 aturQuiet2 104 aturComb2 105 aturIcomb1 106 aturLineprob 107 aturQuiet3 108 aturComb3 109 aturIcomb2 110 aturMsgfmt 111 aturMsgpcb 112 aturReverb1 113 aturQuiet4 114 aturReverb2 115 aturQuiet5 116 aturReverb3 117 aturEct 118 aturReverb4 119 aturSegue1 120 aturReverb5 121 aturSegue2 122 aturMsg1 123 aturMedley 124 aturExchmarker 125 aturMsg2 126 aturReverb6 127 aturSegue3 128 aturParams 129 aturReverb7 130 aturSegue4 131 aturShowtime 200 vtucG9941 201 vtucQuiet1 202 vtucChDiscov1 203 vtucSynchro1 204 vtucPilot1 205 vtucQuiet2 206 vtucPeriodic1 207 vtucSynchro2 208 vtucChDiscov2 209 vtucSynchro3 210 vtucTraining1 211 vtucSynchro4 212 vtucPilot2 213 vtucTeq 214 vtucEct 215 vtucPilot3 216 vtucPeriodic2 217 vtucTraining2 218 vtucSynchro5 219 vtucMedley 220 vtucSynchro6 221 vtucShowtime 300 vturG9941 301 vturQuiet1 302 vturChDiscov1 303 vturSynchro1 304 vturLineprobe 305 vturPeriodic1 306 vturSynchro2 307 vturChDiscov2 308 vturSynchro3 309 vturQuiet2 310 vturTraining1 311 vturSynchro4 312 vturTeq 313 vturQuiet3 314 vturEct 315 vturPeriodic2 316 vturTraining2 317 vturSynchro5 318 vturMedley 319 vturSynchro6 320 vturShowtime	.1.3.6.1.2.1.10.251.1.1.1.1.16
xdsl2LineStatusLastStateUs The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line.	VDSL2-LINE-TC-MIBXdsl2LastTransmittedState Type Values: 0 atucG9941 1 atucQuiet1 2 atucComb1 3 atucQuiet2 4 atucComb2 5 atucIcomb1 6 atucLineprob 7 atucQuiet3 8 atucComb3 9 atucIComb2 10 atucMsgfmt 11 atucMsgpcb 12 atucQuiet4 13 atucReverb1 14 atucTref1 15 atucReverb2 16 atucEct 17 atucReverb3 18 atucTref2 19 atucReverb4 20 atucSegue1 21 atucMsg1 22 atucReverb5 23 atucSegue2 24 atucMedley 25 atucExchmarker 26 atucMsg2 27 atucReverb6 28 atucSegue3 29 atucParams 30 atucReverb7 31 atucSegue4 32 atucShowtime 100 aturG9941 101 aturQuiet1 102 aturComb1 103 aturQuiet2 104 aturComb2 105 aturIcomb1 106 aturLineprob 107 aturQuiet3 108 aturComb3 109 aturIcomb2 110 aturMsgfmt 111 aturMsgpcb 112 aturReverb1 113 aturQuiet4 114 aturReverb2 115 aturQuiet5 116 aturReverb3 117 aturEct 118 aturReverb4 119 aturSegue1 120 aturReverb5 121 aturSegue2 122 aturMsg1 123 aturMedley 124 aturExchmarker 125 aturMsg2 126 aturReverb6 127 aturSegue3 128 aturParams 129 aturReverb7 130 aturSegue4 131 aturShowtime 200 vtucG9941 201 vtucQuiet1 202 vtucChDiscov1 203 vtucSynchro1 204 vtucPilot1 205 vtucQuiet2 206 vtucPeriodic1 207 vtucSynchro2 208 vtucChDiscov2 209 vtucSynchro3 210 vtucTraining1 211 vtucSynchro4 212 vtucPilot2 213 vtucTeq 214 vtucEct 215 vtucPilot3 216 vtucPeriodic2 217 vtucTraining2 218 vtucSynchro5 219 vtucMedley 220 vtucSynchro6 221 vtucShowtime 300 vturG9941 301 vturQuiet1 302 vturChDiscov1 303 vturSynchro1 304 vturLineprobe 305 vturPeriodic1 306 vturSynchro2 307 vturChDiscov2 308 vturSynchro3 309 vturQuiet2 310 vturTraining1 311 vturSynchro4 312 vturTeq 313 vturQuiet3 314 vturEct 315 vturPeriodic2 316 vturTraining2 317 vturSynchro5 318 vturMedley 319 vturSynchro6 320 vturShowtime	.1.3.6.1.2.1.10.251.1.1.1.1.17
xdsl2LineStatusXtur Indicates the current state (existing failures) of the xTU-R. This is a bitmap of possible conditions.	VDSL2-LINE-TC-MIBXdsl2LineStatus Type Values: 0 noDefect 1 lossOfFraming 2 lossOfSignal 3 lossOfPower 4 initFailure	.1.3.6.1.2.1.10.251.1.1.1.1.18
xdsl2LineStatusXtuc Indicates the current state (existing failures) of the xTU-C. This is a bitmap of possible conditions.	VDSL2-LINE-TC-MIBXdsl2LineStatus Type Values: 0 noDefect 1 lossOfFraming 2 lossOfSignal 3 lossOfPower 4 initFailure	.1.3.6.1.2.1.10.251.1.1.1.1.19
xdsl2LineStatusAttainableRateDs Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the xTU-C transmitter and the xTU-R receiver, coded in bit/s.	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.1.1.1.20
xdsl2LineStatusAttainableRateUs Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the xTU-R transmitter and the xTU-C receiver, coded in bit/s.	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.1.1.1.21
xdsl2LineStatusActPsdDs Actual Power Spectral Density (PSD) Downstream. The average downstream transmit PSD over the subcarriers used for downstream. It ranges from -900 to 0 units of 0.1 dBm/Hz (physical values are -90 to 0 dBm/Hz). A value …	0.1 dBm/HzInteger32 Constraints: range: -900-0 range: 2147483647-2147483647	.1.3.6.1.2.1.10.251.1.1.1.1.22
xdsl2LineStatusActPsdUs Actual Power Spectral Density (PSD) Upstream. The average upstream transmit PSD over the subcarriers used for upstream. It ranges from -900 to 0 units of 0.1 dBm/Hz (physical values are -90 to 0 dBm/Hz). A value of 0x7…	0.1 dBm/HzInteger32 Constraints: range: -900-0 range: 2147483647-2147483647	.1.3.6.1.2.1.10.251.1.1.1.1.23
xdsl2LineStatusActAtpDs Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the xTU-C at the U-C reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dBm (physical val…	0.1 dBmInteger32 Constraints: range: -310-310 range: 2147483647-2147483647	.1.3.6.1.2.1.10.251.1.1.1.1.24
xdsl2LineStatusActAtpUs Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the xTU-R at the U-R reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dBm (physical value…	0.1 dBmInteger32 Constraints: range: -310-310 range: 2147483647-2147483647	.1.3.6.1.2.1.10.251.1.1.1.1.25
xdsl2LineStatusActProfile The G.993.2 profile in use. The configuration parameter xdsl2LConfProfProfiles defines the set of allowed G.993.2 profiles. This parameter indicates the profile in use on this line. This parameter may be derived from t…	VDSL2-LINE-TC-MIBXdsl2LineProfiles Type Values: 0 profile8a 1 profile8b 2 profile8c 3 profile8d 4 profile12a 5 profile12b 6 profile17a 7 profile30a	.1.3.6.1.2.1.10.251.1.1.1.1.26
xdsl2LineStatusActLimitMask The Limit PSD mask and band plan in use. The configuration parameter xdsl2LConfProfLimitMask defines the set of allowed G.993.2 limit PSD masks. This parameter indicates the limit PSD mask in use on this line.	VDSL2-LINE-TC-MIBXdsl2LineLimitMask Type Values: 0 profile8Limit1 1 profile8Limit2 2 profile8Limit3 3 profile8Limit4 4 profile8Limit5 5 profile8Limit6 6 profile8Limit7 7 profile8Limit8 8 profile8Limit9 9 profile8Limit10 10 profile8Limit11 11 profile8Limit12 12 profile8Limit13 13 profile8Limit14 14 profile8Limit15 15 profile8Limit16 16 profile12Limit1 17 profile12Limit2 18 profile12Limit3 19 profile12Limit4 20 profile12Limit5 21 profile12Limit6 22 profile12Limit7 23 profile12Limit8 24 profile12Limit9 25 profile12Limit10 26 profile12Limit11 27 profile12Limit12 28 profile12Limit13 29 profile12Limit14 30 profile12Limit15 31 profile12Limit16 32 profile17Limit1 33 profile17Limit2 34 profile17Limit3 35 profile17Limit4 36 profile17Limit5 37 profile17Limit6 38 profile17Limit7 39 profile17Limit8 40 profile17Limit9 41 profile17Limit10 42 profile17Limit11 43 profile17Limit12 44 profile17Limit13 45 profile17Limit14 46 profile17Limit15 47 profile17Limit16 48 profile30Limit1 49 profile30Limit2 50 profile30Limit3 51 profile30Limit4 52 profile30Limit5 53 profile30Limit6 54 profile30Limit7 55 profile30Limit8 56 profile30Limit9 57 profile30Limit10 58 profile30Limit11 59 profile30Limit12 60 profile30Limit13 61 profile30Limit14 62 profile30Limit15 63 profile30Limit16	.1.3.6.1.2.1.10.251.1.1.1.1.27
xdsl2LineStatusActUs0Mask The US0 PSD mask in use. The configuration parameter xdsl2LConfProfUs0Mask defines the set of allowed US0 PSD masks. This parameter indicates the US0 PSD mask in use on this line. This parameter may be derived from the …	VDSL2-LINE-TC-MIBXdsl2LineUs0Mask Type Values: 0 eu32 1 eu36 2 eu40 3 eu44 4 eu48 5 eu52 6 eu56 7 eu60 8 eu64 9 eu128 10 reserved1 11 reserved2 12 reserved3 13 reserved4 14 reserved5 15 reserved6 16 adlu32 17 adlu36 18 adlu40 19 adlu44 20 adlu48 21 adlu52 22 adlu56 23 adlu60 24 adlu64 25 adlu128 26 reserved7 27 reserved8 28 reserved9 29 reserved10 30 reserved11 31 reserved12	.1.3.6.1.2.1.10.251.1.1.1.1.28
xdsl2LineStatusActSnrModeDs This parameter indicates if the transmitter-referred virtual noise is active on the line in the downstream direction. The configuration parameter xdsl2LConfProfSnrModeDs is used to configure referred virtual noise.	VDSL2-LINE-TC-MIBXdsl2LineSnrMode Type Values: 1 virtualNoiseDisabled 2 virtualNoiseEnabled	.1.3.6.1.2.1.10.251.1.1.1.1.29
xdsl2LineStatusActSnrModeUs This parameter indicates if the transmitter-referred virtual noise is active on the line in the upstream direction. The configuration parameter xdsl2LConfProfSnrModeUs is used to configure referred virtual noise.	VDSL2-LINE-TC-MIBXdsl2LineSnrMode Type Values: 1 virtualNoiseDisabled 2 virtualNoiseEnabled	.1.3.6.1.2.1.10.251.1.1.1.1.30
xdsl2LineStatusElectricalLength This parameter contains the estimated electrical length expressed in dB at 1 MHz, kl0. This is the final electrical length that would have been sent from the VTU-O to VTU-R if the electrical length was not forced by th…	0.1 dBUnsigned32 Constraints: range: 0-1280	.1.3.6.1.2.1.10.251.1.1.1.1.31
xdsl2LineStatusTssiDs The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1 (Downstream).	VDSL2-LINE-TC-MIBXdsl2Tssi Type Constraints: range: 0..96	.1.3.6.1.2.1.10.251.1.1.1.1.32
xdsl2LineStatusTssiUs The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1 (Upstream).	VDSL2-LINE-TC-MIBXdsl2Tssi Type Constraints: range: 0..96	.1.3.6.1.2.1.10.251.1.1.1.1.33
xdsl2LineStatusMrefPsdDs The MEDLEY Reference PSD status parameters in the downstream direction expressed as the set of breakpoints exchanged at initialization.	VDSL2-LINE-TC-MIBXdsl2MrefPsdDs Type Constraints: range: 0..192	.1.3.6.1.2.1.10.251.1.1.1.1.34
xdsl2LineStatusMrefPsdUs The MEDLEY Reference PSD status parameters in the upstream direction expressed as the set of breakpoints exchanged at initialization.	VDSL2-LINE-TC-MIBXdsl2MrefPsdUs Type Constraints: range: 0..128	.1.3.6.1.2.1.10.251.1.1.1.1.35
xdsl2LineStatusTrellisDs This parameter reports whether trellis coding is in use in the downstream direction.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.251.1.1.1.1.36
xdsl2LineStatusTrellisUs This parameter reports whether trellis coding is in use in the upstream direction.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.251.1.1.1.1.37
xdsl2LineStatusActualCe (ACTUALCE) This parameter reports the cyclic extension used on the line. It is coded as an unsigned integer from 2 to 16 in units of N/32 samples, where 2N is the Inverse Discrete Fourier Transform (IDFT) size.	N/32 samplesUnsigned32 Constraints: range: 2-16	.1.3.6.1.2.1.10.251.1.1.1.1.38

The table xdsl2LineBandTable contains the, per-band line
status parameters of the VDSL2/ADSL/ADSL2 or ADSL2+ line.
The parameters in this table are updated at line initialization
time and at Showtime.

xdsl2LineBandEntry row .1.3.6.1.2.1.10.251.1.1.2.1

One index of this table is an interface index where the
interface
has an ifType of vdsl2(251). A second index of this table is a
per-band index covering both VDSL2 and ADSL/ADSL2/ADSL2+.

Indexes

IF-MIBifIndex xdsl2LineBand

Column	Syntax	OID
xdsl2LineBand Identifies the band(s) associated with this line. For ADSL/ADSL2/ADSL2+, the values 'upstream' and 'downstream' will always be present. For VDSL2, a subset of {'us0', 'ds1', 'us1' ... 'ds4', 'us4' } will …	VDSL2-LINE-TC-MIBXdsl2Band Type Values: 1 upstream 2 downstream 3 us0 4 ds1 5 us1 6 ds2 7 us2 8 ds3 9 us3 10 ds4 11 us4	.1.3.6.1.2.1.10.251.1.1.2.1.1
xdsl2LineBandStatusLnAtten Line Attenuation. When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all subcarriers of that ba…	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.2.1.10.251.1.1.2.1.2
xdsl2LineBandStatusSigAtten Signal Attenuation. When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all subcarriers of that …	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.2.1.10.251.1.1.2.1.3
xdsl2LineBandStatusSnrMargin SNR Margin is the maximum increase in dB of the noise power received at the xTU (xTU-R for a band in the downstream direction and xTU-C for a band in the upstream direction), such that the BER requirements are met for a…	0.1 dBInteger32 Constraints: range: -640-630 range: 2147483646-2147483647	.1.3.6.1.2.1.10.251.1.1.2.1.4

The table xdsl2LineSegmentTable contains status parameters
of VDSL2/ADSL/ADSL2 and ADSL2+ subcarriers.
The parameters in this table are updated when a measurement
request is made using the xdsl2LineCmndConfBpsc object.
          
Note that a bits-per-subcarrier measurement is also performed
during a line diagnostic procedure.  This table provides an
additional mechanism to fetch the bits-per-subcarrier data.  This
additional mechanism is provided so that bits-per-subcarrier
data may be fetched without forcing the line into no power state.
This is useful because the bits-per-subcarrier allocation may be
adjusted at Showtime due to rate adaption and bit swapping.
          
The implementation of this additional mechanism for measuring
bits per subcarrier is not mandatory.

xdsl2LineSegmentEntry row .1.3.6.1.2.1.10.251.1.2.1.1

The table xdsl2LineSegmentEntry contains status parameters
of VDSL2/ADSL/ADSL2 and ADSL2+ subcarriers.

Objects in the table refer to NSus and NSds. For G.993.2, the
value of NSus and NSds are, respectively…

Indexes

IF-MIBifIndex xdsl2LineSegmentDirection xdsl2LineSegment

Column	Syntax	OID
xdsl2LineSegmentDirection The direction of the subcarrier either upstream or downstream.	VDSL2-LINE-TC-MIBXdsl2Direction Type Values: 1 upstream 2 downstream	.1.3.6.1.2.1.10.251.1.2.1.1.1
xdsl2LineSegment The segment of the subcarriers status information provided by this row. Status parameters in this table are retrieved in segments. The first segment of the status information is retrieved with xdsl2LineSegment=1, the se…	Unsigned32 Constraints: range: 1-8	.1.3.6.1.2.1.10.251.1.2.1.1.2
xdsl2LineSegmentBitsAlloc The bits allocation per subcarrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) subcarriers. When more than 512 subcarriers are supported, the status information is reported th…	bitsVDSL2-LINE-TC-MIBXdsl2BitsAlloc Type Constraints: range: 0..256	.1.3.6.1.2.1.10.251.1.2.1.1.3
xdsl2LineSegmentRowStatus Row Status. The SNMP agent will create a row in this table for storing the results of a measurement performed on the associated line, if the row does not already exist. The SNMP manager is not permitted …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.251.1.2.1.1.4

The table xdsl2ChannelStatusTable contains status
          
parameters of VDSL2/ADSL/ADSL2 or ADSL2+ channel.
This table contains live data from equipment.

xdsl2ChannelStatusEntry row .1.3.6.1.2.1.10.251.1.2.2.1

One index of this table is an interface index where the
interface has an ifType of a DSL channel. A second index of
this table is the termination unit.

Indexes

IF-MIBifIndex xdsl2ChStatusUnit

Column	Syntax	OID
xdsl2ChStatusUnit The termination unit.	VDSL2-LINE-TC-MIBXdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.2.1.10.251.1.2.2.1.1
xdsl2ChStatusActDataRate The actual net data rate at which the bearer channel is operating, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. The data rate is coded in bit/s.	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.2.2.1.2
xdsl2ChStatusPrevDataRate The previous net data rate that the bearer channel was operating at just before the latest rate change event. This could be a full or short initialization, fast retrain, DRA or power management transitions, excluding t…	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.2.2.1.3
xdsl2ChStatusActDelay The actual one-way interleaving delay introduced by the PMS-TC in the direction of the bearer channel, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. It is coded in ms (round…	millisecondsUnsigned32 Constraints: range: 0-8176	.1.3.6.1.2.1.10.251.1.2.2.1.4
xdsl2ChStatusActInp Actual impulse noise protection. This parameter reports the actual impulse noise protection (INP) on the bearer channel in the L0 state. In the L1 or L2 state, the parameter contains the INP in the previ…	0.1 symbolsUnsigned32 Constraints: range: 0-255	.1.3.6.1.2.1.10.251.1.2.2.1.5
xdsl2ChStatusInpReport Impulse noise protection reporting mode.	VDSL2-LINE-TC-MIBXdsl2ChInpReport Type Values: 1 inpComputedUsingFormula 2 inpEstimatedByXtur	.1.3.6.1.2.1.10.251.1.2.2.1.6
xdsl2ChStatusNFec Actual size of Reed-Solomon codeword. This parameter reports the actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. The value is coded in by…	bytesUnsigned32 Constraints: range: 0-255	.1.3.6.1.2.1.10.251.1.2.2.1.7
xdsl2ChStatusRFec Actual number of Reed-Solomon redundancy bytes. This parameter reports the actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. …	bitsUnsigned32 Constraints: range: 0-16	.1.3.6.1.2.1.10.251.1.2.2.1.8
xdsl2ChStatusLSymb Actual number of bits per symbol. This parameter reports the actual number of bits per symbol assigned to the latency path in which the bearer channel is transported. This value does not include trellis overhead. The …	bitsUnsigned32 Constraints: range: 0-65535	.1.3.6.1.2.1.10.251.1.2.2.1.9
xdsl2ChStatusIntlvDepth Actual interleaving depth. This parameter reports the actual depth of the interleaver used in the latency path in which the bearer channel is transported. The value ranges from 1 to 4096 in steps of 1. The value 1 indic…	Unsigned32 Constraints: range: 1-4096	.1.3.6.1.2.1.10.251.1.2.2.1.10
xdsl2ChStatusIntlvBlock Actual interleaving block length. This parameter reports the actual block length of the interleaver used in the latency path in which the bearer channel is transported. The value ranges from 4 to 255 in s…	Unsigned32 Constraints: range: 4-255	.1.3.6.1.2.1.10.251.1.2.2.1.11
xdsl2ChStatusLPath Actual latency path. This parameter reports the index of the actual latency path in which the bearer is transported. The valid values are 0, 1, 2 and 3. For G.992.1, the FAST path shall be mapped to the latency index 0,…	Unsigned32 Constraints: range: 0-3	.1.3.6.1.2.1.10.251.1.2.2.1.12
xdsl2ChStatusAtmStatus Indicates current state (existing failures) of the DSL channel in case its Data Path is ATM. This is a bitmap of possible conditions. In case the channel is not of ATM Data Path, the object is set to '0'.	VDSL2-LINE-TC-MIBXdsl2ChAtmStatus Type Values: 0 noDefect 1 noCellDelineation 2 lossOfCellDelineation	.1.3.6.1.2.1.10.251.1.2.2.1.13
xdsl2ChStatusPtmStatus Indicates current state (existing failures) of the DSL channel in case its Data Path is PTM (Packet Transfer Mode). This is a bitmap of possible conditions. In case the channel is not of PTM Data Path, the object is set…	VDSL2-LINE-TC-MIBXdsl2ChPtmStatus Type Values: 0 noDefect 1 outOfSync	.1.3.6.1.2.1.10.251.1.2.2.1.14

The table xdsl2SCStatusTable contains
status parameters for VDSL2/ADSL/ADSL2 and ADSL2+ that
provide information about the size of parameters in
xdsl2SCStatusSegmentTable.
The parameters in this table MUST be updated after a loop
diagnostic procedure, MAY be updated after a line
initialization, and MAY be updated at Showtime.

xdsl2SCStatusEntry row .1.3.6.1.2.1.10.251.1.2.3.1

One index of this table is an interface index where the
interface has an ifType of vdsl2(251). A second index of this
table is the transmission direction.

Indexes

IF-MIBifIndex xdsl2SCStatusDirection

Column	Syntax	OID
xdsl2SCStatusDirection The direction of the subcarrier either upstream or downstream.	VDSL2-LINE-TC-MIBXdsl2Direction Type Values: 1 upstream 2 downstream	.1.3.6.1.2.1.10.251.1.2.3.1.1
xdsl2SCStatusLinScale The scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loop diagnostic procedure. It is represented as an unsigned in…	Unsigned32 Constraints: range: 1-65535	.1.3.6.1.2.1.10.251.1.2.3.1.2
xdsl2SCStatusLinScGroupSize Number of subcarriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4, and 8. For ADSL, this parameter is equal to one and, for VD…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.2.1.10.251.1.2.3.1.3
xdsl2SCStatusLogMt This parameter contains the number of symbols used to measure the Hlog(f) values. It is represented as an unsigned integer in the range from 1 to 2^16-1. After a loop diagnostic procedure, this parameter shall contain …	Unsigned32 Constraints: range: 1-65535	.1.3.6.1.2.1.10.251.1.2.3.1.4
xdsl2SCStatusLogScGroupSize Number of subcarriers per group used to report the H(f) logarithmic representation values for the respective transmission direction. The valid values are 1, 2, 4, and 8. For ADSL, this parameter is equal to 1, and for …	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.2.1.10.251.1.2.3.1.5
xdsl2SCStatusQlnMt This parameter contains the number of symbols used to measure the QLN(f) values. It is an unsigned integer in the range from 1 to 2^16-1. After a loop diagnostic procedure, this parameter shall contain the number of s…	Unsigned32 Constraints: range: 1-65535	.1.3.6.1.2.1.10.251.1.2.3.1.6
xdsl2SCStatusQlnScGroupSize Number of subcarriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4, and 8. For ADSL, this parameter is equal to 1, and for VDSL2, it is equ…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.2.1.10.251.1.2.3.1.7
xdsl2SCStatusSnrMtime This parameter contains the number of symbols used to measure the SNR(f) values. It is an unsigned integer in the range from 1 to 2^16-1. After a loop diagnostic procedure, this parameter shall contain the number of s…	symbolsUnsigned32 Constraints: range: 1-65535	.1.3.6.1.2.1.10.251.1.2.3.1.8
xdsl2SCStatusSnrScGroupSize Number of subcarriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4, and 8. For ADSL, this parameter is equal to 1, and for VDSL2, it is equal to the size…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.2.1.10.251.1.2.3.1.9
xdsl2SCStatusAttainableRate Maximum Attainable Data Rate. The maximum net data rate currently attainable by the xTU-C transmitter and xTU-R receiver (when referring to downstream direction) or by the xTU-R transmitter and xTU-C receiver (when ref…	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.2.3.1.10
xdsl2SCStatusRowStatus Row Status. The SNMP agent will create a row in this table for storing the results of a DELT performed on the associated line, if the row does not already exist. When a row is created in this table, the …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.251.1.2.3.1.11

The table xdsl2SCStatusBandTable contains subcarrier status
parameters for VDSL2/ADSL/ADSL2 and ADSL2+ that are grouped per-
band.
For ADSL/ADSL2/ADSL2+, there is a single upstream band and a
single downstream band.  For VDSL2, there are several downstream
bands and several upstream bands.
The parameters in this table are only available after a loop
diagnostic procedure.

xdsl2SCStatusBandEntry row .1.3.6.1.2.1.10.251.1.2.4.1

One index of this table is an interface index where the
interface

has an ifType of vdsl2(251). A second index of this table is the
transmission band.

Indexes

IF-MIBifIndex xdsl2SCStatusBand

Column	Syntax	OID
xdsl2SCStatusBand The transmission band.	VDSL2-LINE-TC-MIBXdsl2Band Type Values: 1 upstream 2 downstream 3 us0 4 ds1 5 us1 6 ds2 7 us2 8 ds3 9 us3 10 ds4 11 us4	.1.3.6.1.2.1.10.251.1.2.4.1.1
xdsl2SCStatusBandLnAtten When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all subcarriers during diagnostics mode. Whe…	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.2.1.10.251.1.2.4.1.2
xdsl2SCStatusBandSigAtten When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all subcarriers during Showtime after the di…	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.2.1.10.251.1.2.4.1.3

The table xdsl2SCStatusSegmentTable contains status
parameters of VDSL2/ADSL/ADSL2 and ADSL2+ subcarriers.
          
Several objects in the table refer to NSus and NSds.  For
G.993.2, the value of NSus and NSds are, respectively, the
indices of the highest supported upstream and downstream
subcarriers according to the selected implementation profile.
For ADSL, NSus is equal to NSCus-1 and NSds is equal to NSCds-1.
          
The parameters in this table MUST be updated after a loop
          
diagnostic procedure and MAY be updated after a line
initialization and MAY be updated at Showtime.

xdsl2SCStatusSegmentEntry row .1.3.6.1.2.1.10.251.1.2.5.1

One index of this table is an interface index where the
interface has an ifType of vdsl2(251). A second index of this
table is the transmission direction. A third index identifies
the specific segment of the subcarrie…

Indexes

IF-MIBifIndex xdsl2SCStatusDirection xdsl2SCStatusSegment

Column	Syntax	OID
xdsl2SCStatusSegment The segment of the subcarriers status information provided by this row. Several status parameters in this table are retrieved in segments. The first segment of the status information is retrieved with xdsl2SCStatusSegme…	Unsigned32 Constraints: range: 1-8	.1.3.6.1.2.1.10.251.1.2.5.1.1
xdsl2SCStatusSegmentLinReal An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) subcarrier groups and can be retrieved in a sin…	OctetString Constraints: range: 0-1024	.1.3.6.1.2.1.10.251.1.2.5.1.2
xdsl2SCStatusSegmentLinImg An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) subcarrier groups and can be retrieved in a sin…	OctetString Constraints: range: 0-1024	.1.3.6.1.2.1.10.251.1.2.5.1.3
xdsl2SCStatusSegmentLog An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) subcarrier groups and can be retrieved in a single seg…	dBOctetString Constraints: range: 0-1024	.1.3.6.1.2.1.10.251.1.2.5.1.4
xdsl2SCStatusSegmentQln An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) subcarrier groups and can be retrieved in a single segment. The number o…	dBm/HzOctetString Constraints: range: 0-512	.1.3.6.1.2.1.10.251.1.2.5.1.5
xdsl2SCStatusSegmentSnr The SNR Margin per subcarrier group, expressing the ratio between the received signal power and received noise power per subscriber group. It is an array of 512 octets, designed for supporting up to 512 (downstream) su…	0.5 dBOctetString Constraints: range: 0-512	.1.3.6.1.2.1.10.251.1.2.5.1.6
xdsl2SCStatusSegmentBitsAlloc The bits allocation per subcarrier. An array of 256 octets (512 nibbles) designed for supporting up to 512 (downstream) subcarriers. When more than 512 subcarriers are supported, the status information …	bitsVDSL2-LINE-TC-MIBXdsl2BitsAlloc Type Constraints: range: 0..256	.1.3.6.1.2.1.10.251.1.2.5.1.7
xdsl2SCStatusSegmentGainAlloc The gain allocation per subcarrier. An array of 512 16-bit values, designed for supporting up to 512 (downstream) subcarriers. When more then 512 subcarriers are supported, the status information is reported through m…	OctetString Constraints: range: 0-1024	.1.3.6.1.2.1.10.251.1.2.5.1.8

The table xdsl2LineInventoryTable contains an inventory of the
DSL termination unit.

xdsl2LineInventoryEntry row .1.3.6.1.2.1.10.251.1.3.1.1

One index of this table is an interface index where the
interface
has an ifType of vdsl2(251). A second index of this table is the
termination unit.

Indexes

IF-MIBifIndex xdsl2LInvUnit

Column	Syntax	OID
xdsl2LInvUnit The termination unit.	VDSL2-LINE-TC-MIBXdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.2.1.10.251.1.3.1.1.1
xdsl2LInvG994VendorId The ADSL Transceiver Unit (ATU) G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed by a (regionally allocated) provider code, as…	OctetString Constraints: range: 8-8	.1.3.6.1.2.1.10.251.1.3.1.1.2
xdsl2LInvSystemVendorId The ATU System Vendor ID (identifies the xTU system integrator) as inserted in the Overhead Messages (both xTUs for G.992.3, G.992.4, G.992.5, and G.993.2) or in the Embedded Operations Channel (xTU-R in G.992.1 and G.9…	OctetString Constraints: range: 8-8	.1.3.6.1.2.1.10.251.1.3.1.1.3
xdsl2LInvVersionNumber The xTU version number (vendor-specific information) as inserted in the Overhead Messages (both xTUs for G.992.3, G.992.4, G.992.5, and G.993.2) or in the Embedded Operations Channel (xTU-R in G.992.1 and G.992.2). It …	OctetString Constraints: range: 0-16	.1.3.6.1.2.1.10.251.1.3.1.1.4
xdsl2LInvSerialNumber The xTU serial number (vendor-specific information) as inserted in the Overhead Messages (both xTUs for G.992.3, G.992.4, G.992.5, and G.993.2) or in the Embedded Operations Channel (xTU-R in G.992.1 and G.992.2). It i…	OctetString Constraints: range: 0-32	.1.3.6.1.2.1.10.251.1.3.1.1.5
xdsl2LInvSelfTestResult The xTU self-test result, coded as a 32-bit value. The most significant octet of the result is '0' if the self-test passed, and '1' if the self-test failed. The interpretation of the other octets is vendor discretiona…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.3.1.1.6
xdsl2LInvTransmissionCapabilities The xTU transmission system capability list of the different coding types. It is coded in a bitmap representation with 1 or more bits set. A bit set to '1' means that the xTU supports the respective coding. The value…	VDSL2-LINE-TC-MIBXdsl2TransmissionModeType Type Values: 0 ansit1413 1 etsi 2 g9921PotsNonOverlapped 3 g9921PotsOverlapped 4 g9921IsdnNonOverlapped 5 g9921isdnOverlapped 6 g9921tcmIsdnNonOverlapped 7 g9921tcmIsdnOverlapped 8 g9922potsNonOverlapped 9 g9922potsOverlapped 10 g9922tcmIsdnNonOverlapped 11 g9922tcmIsdnOverlapped 12 g9921tcmIsdnSymmetric 13 reserved1 14 reserved2 15 reserved3 16 reserved4 17 reserved5 18 g9923PotsNonOverlapped 19 g9923PotsOverlapped 20 g9923IsdnNonOverlapped 21 g9923isdnOverlapped 22 reserved6 23 reserved7 24 g9924potsNonOverlapped 25 g9924potsOverlapped 26 reserved8 27 reserved9 28 g9923AnnexIAllDigNonOverlapped 29 g9923AnnexIAllDigOverlapped 30 g9923AnnexJAllDigNonOverlapped 31 g9923AnnexJAllDigOverlapped 32 g9924AnnexIAllDigNonOverlapped 33 g9924AnnexIAllDigOverlapped 34 g9923AnnexLMode1NonOverlapped 35 g9923AnnexLMode2NonOverlapped 36 g9923AnnexLMode3Overlapped 37 g9923AnnexLMode4Overlapped 38 g9923AnnexMPotsNonOverlapped 39 g9923AnnexMPotsOverlapped 40 g9925PotsNonOverlapped 41 g9925PotsOverlapped 42 g9925IsdnNonOverlapped 43 g9925isdnOverlapped 44 reserved10 45 reserved11 46 g9925AnnexIAllDigNonOverlapped 47 g9925AnnexIAllDigOverlapped 48 g9925AnnexJAllDigNonOverlapped 49 g9925AnnexJAllDigOverlapped 50 g9925AnnexMPotsNonOverlapped 51 g9925AnnexMPotsOverlapped 52 reserved12 53 reserved13 54 reserved14 55 reserved15 56 g9932AnnexA 57 g9932AnnexB 58 g9932AnnexC 59 reserved16 60 reserved17 61 reserved18 62 reserved19 63 reserved20	.1.3.6.1.2.1.10.251.1.3.1.1.7

The table xdsl2PMLineCurrTable contains current Performance
Monitoring results for DSL lines.

xdsl2PMLineCurrEntry row .1.3.6.1.2.1.10.251.1.4.1.1.1

One index of this table is an interface index where the
interface has an ifType of vdsl2(251). A second index of this
table is the termination unit.

Indexes

IF-MIBifIndex xdsl2PMLCurrUnit

Column	Syntax	OID
xdsl2PMLCurrUnit The termination unit.	VDSL2-LINE-TC-MIBXdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.2.1.10.251.1.4.1.1.1.1
xdsl2PMLCurr15MValidIntervals The number of 15-minute PM intervals for which data was collected. The value will typically be equal to the maximum number of 15-minute intervals the implementation is planned to store (i.e., beyond the scope of this M…	Unsigned32 Constraints: range: 0-96	.1.3.6.1.2.1.10.251.1.4.1.1.1.2
xdsl2PMLCurr15MInvalidIntervals The number of 15-minute PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).	Unsigned32 Constraints: range: 0-96	.1.3.6.1.2.1.10.251.1.4.1.1.1.3
xdsl2PMLCurr15MTimeElapsed Total elapsed seconds in this interval.	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.2.1.10.251.1.4.1.1.1.4
xdsl2PMLCurr15MFecs Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.1.1.5
xdsl2PMLCurr15MEs Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >=1 OR LPR >= 1. xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >=1 OR…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.1.1.6
xdsl2PMLCurr15MSes Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: (FEBE anomalies in one or mor…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.1.1.7
xdsl2PMLCurr15MLoss Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R).	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.1.1.8
xdsl2PMLCurr15MUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the onset of 10 contiguous seconds with no severely errored secon…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.1.1.9
xdsl2PMLCurr1DayValidIntervals The number of 24-hour PM intervals for which data was collected. The value will typically be equal to the maximum number of 24-hour intervals the implementation is planned to store (i.e., beyond the scope of this MIB m…	Unsigned32 Constraints: range: 0-30	.1.3.6.1.2.1.10.251.1.4.1.1.1.10
xdsl2PMLCurr1DayInvalidIntervals The number of 24-hour PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).	Unsigned32 Constraints: range: 0-30	.1.3.6.1.2.1.10.251.1.4.1.1.1.11
xdsl2PMLCurr1DayTimeElapsed Total elapsed seconds in this interval.	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.2.1.10.251.1.4.1.1.1.12
xdsl2PMLCurr1DayFecs Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.1.1.13
xdsl2PMLCurr1DayEs Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.1.1.14
xdsl2PMLCurr1DaySes Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: (FEBE anomalies in one or mor…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.1.1.15
xdsl2PMLCurr1DayLoss Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R).	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.1.1.16
xdsl2PMLCurr1DayUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the onset of 10 contiguous seconds with no severely errored second…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.1.1.17

The table xdsl2PMLineInitCurrTable contains current
initialization counters for DSL lines.

xdsl2PMLineInitCurrEntry row .1.3.6.1.2.1.10.251.1.4.1.2.1

The index of this table is an interface index where the
interface has an ifType of vdsl2(251).

Indexes

IF-MIBifIndex

Column	Syntax	OID
xdsl2PMLInitCurr15MValidIntervals The number of 15-minute PM intervals for which data was collected. The value will typically be equal to the maximum number of 15-minute intervals the implementation is planned to store (i.e., beyond the scope of this M…	Unsigned32 Constraints: range: 0-96	.1.3.6.1.2.1.10.251.1.4.1.2.1.1
xdsl2PMLInitCurr15MInvalidIntervals The number of 15-minute PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).	Unsigned32 Constraints: range: 0-96	.1.3.6.1.2.1.10.251.1.4.1.2.1.2
xdsl2PMLInitCurr15MTimeElapsed Total elapsed seconds in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.2.1.3
xdsl2PMLInitCurr15MFullInits Count of full initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.2.1.4
xdsl2PMLInitCurr15MFailedFullInits Count of failed full initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.2.1.5
xdsl2PMLInitCurr15MShortInits Count of short initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.2.1.6
xdsl2PMLInitCurr15MFailedShortInits Count of failed short initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.2.1.7
xdsl2PMLInitCurr1DayValidIntervals The number of 24-hour PM intervals for which data was collected. The value will typically be equal to the maximum number of 24-hour intervals the implementation is planned to store (i.e., beyond the scope of this MIB m…	Unsigned32 Constraints: range: 0-30	.1.3.6.1.2.1.10.251.1.4.1.2.1.8
xdsl2PMLInitCurr1DayInvalidIntervals The number of 24-hour PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).	Unsigned32 Constraints: range: 0-30	.1.3.6.1.2.1.10.251.1.4.1.2.1.9
xdsl2PMLInitCurr1DayTimeElapsed Total elapsed seconds in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.2.1.10
xdsl2PMLInitCurr1DayFullInits Count of full initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.2.1.11
xdsl2PMLInitCurr1DayFailedFullInits Count of failed full initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.2.1.12
xdsl2PMLInitCurr1DayShortInits Count of short initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.2.1.13
xdsl2PMLInitCurr1DayFailedShortInits Count of failed short initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.2.1.14

The table xdsl2PMLineHist15MinTable contains PM line history
for 15-minute intervals of DSL line.

xdsl2PMLineHist15MinEntry row .1.3.6.1.2.1.10.251.1.4.1.3.1

One index of this table is an interface index where the
interface has an ifType of vdsl2(251). A second index of this
table is the transmission unit. The third index is the interval
number.

Indexes

IF-MIBifIndex xdsl2PMLHist15MUnit xdsl2PMLHist15MInterval

Column	Syntax	OID
xdsl2PMLHist15MUnit The termination unit.	VDSL2-LINE-TC-MIBXdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.2.1.10.251.1.4.1.3.1.1
xdsl2PMLHist15MInterval The interval number.	Unsigned32 Constraints: range: 1-96	.1.3.6.1.2.1.10.251.1.4.1.3.1.2
xdsl2PMLHist15MMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.3.1.3
xdsl2PMLHist15MFecs Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.3.1.4
xdsl2PMLHist15MEs Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.3.1.5
xdsl2PMLHist15MSes Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: (FEBE anomalies in one or mor…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.3.1.6
xdsl2PMLHist15MLoss Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R).	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.3.1.7
xdsl2PMLHist15MUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the onset of 10 contiguous seconds with no severely errored second…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.3.1.8
xdsl2PMLHist15MValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.251.1.4.1.3.1.9

The table xdsl2PMLineHist1DayTable contains PM line history
for 24-hour intervals of DSL line.

xdsl2PMLineHist1DayEntry row .1.3.6.1.2.1.10.251.1.4.1.4.1

One index of this table is an interface index where the
interface has an ifType of vdsl2(251). A second index of this
table is the transmission unit.The third index is the interval
number.

Indexes

IF-MIBifIndex xdsl2PMLHist1DUnit xdsl2PMLHist1DInterval

Column	Syntax	OID
xdsl2PMLHist1DUnit The termination unit.	VDSL2-LINE-TC-MIBXdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.2.1.10.251.1.4.1.4.1.1
xdsl2PMLHist1DInterval The interval number.	Unsigned32 Constraints: range: 1-30	.1.3.6.1.2.1.10.251.1.4.1.4.1.2
xdsl2PMLHist1DMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.4.1.3
xdsl2PMLHist1DFecs Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.4.1.4
xdsl2PMLHist1DEs Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.4.1.5
xdsl2PMLHist1DSes Count of seconds during this interval that there was: xTU-C: (CRC-8 anomalies in one or more of the received bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1. xTU-R: (FEBE anomalies in one or mor…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.4.1.6
xdsl2PMLHist1DLoss Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R).	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.4.1.7
xdsl2PMLHist1DUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely errored seconds, and ends at the onset of 10 contiguous seconds with no severely errored second…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.4.1.8
xdsl2PMLHist1DValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.251.1.4.1.4.1.9

The table xdsl2PMLineInitHist15MinTable contains PM line
initialization history for 15-minute intervals of DSL
line.

xdsl2PMLineInitHist15MinEntry row .1.3.6.1.2.1.10.251.1.4.1.5.1

One index of this table is an interface index where the
interface has an ifType of vdsl2(251). A second index is the
interval number.

Indexes

IF-MIBifIndex xdsl2PMLInitHist15MInterval

Column	Syntax	OID
xdsl2PMLInitHist15MInterval The interval number.	Unsigned32 Constraints: range: 1-96	.1.3.6.1.2.1.10.251.1.4.1.5.1.1
xdsl2PMLInitHist15MMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.5.1.2
xdsl2PMLInitHist15MFullInits Count of full initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.5.1.3
xdsl2PMLInitHist15MFailedFullInits Count of failed full initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.5.1.4
xdsl2PMLInitHist15MShortInits Count of short initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.5.1.5
xdsl2PMLInitHist15MFailedShortInits Count of failed short initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.5.1.6
xdsl2PMLInitHist15MValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.251.1.4.1.5.1.7

The table xdsl2PMLineInitHist1DayTable contains PM line
initialization history for 24-hour intervals for DSL
lines.

xdsl2PMLineInitHist1DayEntry row .1.3.6.1.2.1.10.251.1.4.1.6.1

One index of this table is an interface index where the
interface has an ifType of vdsl2(251). A second index is the
interval number.

Indexes

IF-MIBifIndex xdsl2PMLInitHist1DInterval

Column	Syntax	OID
xdsl2PMLInitHist1DInterval The interval number.	Unsigned32 Constraints: range: 1-30	.1.3.6.1.2.1.10.251.1.4.1.6.1.1
xdsl2PMLInitHist1DMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.6.1.2
xdsl2PMLInitHist1DFullInits Count of full initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.6.1.3
xdsl2PMLInitHist1DFailedFullInits Count of failed full initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.6.1.4
xdsl2PMLInitHist1DShortInits Count of short initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.6.1.5
xdsl2PMLInitHist1DFailedShortInits Count of failed short initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.1.6.1.6
xdsl2PMLInitHist1DValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.251.1.4.1.6.1.7

The table xdsl2PMChCurrTable contains current Performance
Monitoring results for DSL channels.

xdsl2PMChCurrEntry row .1.3.6.1.2.1.10.251.1.4.2.1.1

One index of this table is an interface index where the
interface has an ifType of a DSL channel. A second index of
this table is the termination unit.

Indexes

IF-MIBifIndex xdsl2PMChCurrUnit

Column	Syntax	OID
xdsl2PMChCurrUnit The termination unit.	VDSL2-LINE-TC-MIBXdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.2.1.10.251.1.4.2.1.1.1
xdsl2PMChCurr15MValidIntervals The number of 15-minute PM intervals for which data was collected. The value will typically be equal to the maximum number of 15-minute intervals the implementation is planned to store (i.e., beyond the scope of this M…	Unsigned32 Constraints: range: 0-96	.1.3.6.1.2.1.10.251.1.4.2.1.1.2
xdsl2PMChCurr15MInvalidIntervals The number of 15-minute PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).	Unsigned32 Constraints: range: 0-96	.1.3.6.1.2.1.10.251.1.4.2.1.1.3
xdsl2PMChCurr15MTimeElapsed Total elapsed seconds in this interval.	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.2.1.10.251.1.4.2.1.1.4
xdsl2PMChCurr15MCodingViolations Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) an…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.2.1.1.5
xdsl2PMChCurr15MCorrectedBlocks Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each relat…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.2.1.1.6
xdsl2PMChCurr1DayValidIntervals The number of 24-hour PM intervals for which data was collected. The value will typically be equal to the maximum number of 24-hour intervals the implementation is planned to store (i.e., beyond the scope of this MIB m…	Unsigned32 Constraints: range: 0-30	.1.3.6.1.2.1.10.251.1.4.2.1.1.7
xdsl2PMChCurr1DayInvalidIntervals The number of 24-hour PM intervals for which no data is available. The value will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).	Unsigned32 Constraints: range: 0-30	.1.3.6.1.2.1.10.251.1.4.2.1.1.8
xdsl2PMChCurr1DayTimeElapsed Total elapsed seconds in this interval.	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.2.1.10.251.1.4.2.1.1.9
xdsl2PMChCurr1DayCodingViolations Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.2.1.1.10
xdsl2PMChCurr1DayCorrectedBlocks Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each relat…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.2.1.1.11

The table xdsl2PMChHist15MinTable contains Performance
Monitoring (PM) history for 15-minute intervals for DSL channels
PM.

xdsl2PMChHist15MinEntry row .1.3.6.1.2.1.10.251.1.4.2.2.1

One index of this table is an interface index where the
interface has an ifType of a DSL channel. A second index of
this table is the transmission unit. The third index is the
interval number.

Indexes

IF-MIBifIndex xdsl2PMChHist15MUnit xdsl2PMChHist15MInterval

Column	Syntax	OID
xdsl2PMChHist15MUnit The termination unit.	VDSL2-LINE-TC-MIBXdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.2.1.10.251.1.4.2.2.1.1
xdsl2PMChHist15MInterval The interval number.	Unsigned32 Constraints: range: 1-96	.1.3.6.1.2.1.10.251.1.4.2.2.1.2
xdsl2PMChHist15MMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.2.2.1.3
xdsl2PMChHist15MCodingViolations Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) an…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.2.2.1.4
xdsl2PMChHist15MCorrectedBlocks Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each relat…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.2.2.1.5
xdsl2PMChHist15MValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.251.1.4.2.2.1.6

The table xdsl2PMChHist1DTable contains Performance
Monitoring (PM) history for 1-day intervals for DSL channels
PM.

xdsl2PMChHist1DEntry row .1.3.6.1.2.1.10.251.1.4.2.3.1

One index of this table is an interface index where the
interface has an ifType of a DSL channel. A second index of

this table is the transmission unit. The third index is the
interval number.

Indexes

IF-MIBifIndex xdsl2PMChHist1DUnit xdsl2PMChHist1DInterval

Column	Syntax	OID
xdsl2PMChHist1DUnit The termination unit.	VDSL2-LINE-TC-MIBXdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.2.1.10.251.1.4.2.3.1.1
xdsl2PMChHist1DInterval The interval number.	Unsigned32 Constraints: range: 1-30	.1.3.6.1.2.1.10.251.1.4.2.3.1.2
xdsl2PMChHist1DMonitoredTime Total seconds monitored in this interval.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.2.3.1.3
xdsl2PMChHist1DCodingViolations Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.2.3.1.4
xdsl2PMChHist1DCorrectedBlocks Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each relat…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.251.1.4.2.3.1.5
xdsl2PMChHist1DValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.251.1.4.2.3.1.6

The table xdsl2LineConfTemplateTable contains VDSL2/ADSL/
ADSL2 and ADSL2+ line configuration templates.
          
Note that this table is also used to configure the number of
bearer channels.
When the number of bearer channels is increased, the SNMP agent
SHOULD create rows in all tables indexed by a channel index.
When the number of bearer channels is decreased, the SNMP agent
SHOULD delete rows in all tables indexed by a channel index.
For example, if the value of xdsl2LConfTempChan4ConfProfile is
set to a non-null value, then rows SHOULD be created in
xdsl2ChannelStatusTable, xdsl2PMChCurrTable, and all other tables
indexed by a channel index.
          
For example, if the value of xdsl2LConfTempChan2ConfProfile is
set to a null value, then rows SHOULD be deleted in
xdsl2ChannelStatusTable, xdsl2PMChCurrTable, and all other
tables indexed by a channel index.
          
Entries in this table MUST be maintained in a persistent
manner.

xdsl2LineConfTemplateEntry row .1.3.6.1.2.1.10.251.1.5.1.1.1

A default template with an index of 'DEFVAL' will always
exist, and its parameters will be set to vendor-specific values,
unless otherwise specified in this document.

Indexes

xdsl2LConfTempTemplateName

Column	Syntax	OID
xdsl2LConfTempTemplateName This object identifies a row in this table.	OctetString Constraints: range: 1-32	.1.3.6.1.2.1.10.251.1.5.1.1.1.1
xdsl2LConfTempLineProfile The value of this object identifies the row in the VDSL2/ADSL/ADSL2 and ADSL2+ line configuration Profile Table (xdsl2LineConfProfTable) that applies for this DSL line.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.2.1.10.251.1.5.1.1.1.2
xdsl2LConfTempChan1ConfProfile The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to DSL bearer channel #1. The channel profile name specified her…	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.2.1.10.251.1.5.1.1.1.3
xdsl2LConfTempChan1RaRatioDs Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Min…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.251.1.5.1.1.1.4
xdsl2LConfTempChan1RaRatioUs Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minim…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.251.1.5.1.1.1.5
xdsl2LConfTempChan2ConfProfile The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to DSL bearer channel #2. If the channel is unused, then the obj…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.2.1.10.251.1.5.1.1.1.6
xdsl2LConfTempChan2RaRatioDs Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Min…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.251.1.5.1.1.1.7
xdsl2LConfTempChan2RaRatioUs Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minim…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.251.1.5.1.1.1.8
xdsl2LConfTempChan3ConfProfile The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to DSL bearer channel #3. If the channel is unused, then the obj…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.2.1.10.251.1.5.1.1.1.9
xdsl2LConfTempChan3RaRatioDs Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Min…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.251.1.5.1.1.1.10
xdsl2LConfTempChan3RaRatioUs Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #3 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minim…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.251.1.5.1.1.1.11
xdsl2LConfTempChan4ConfProfile The value of this object identifies the row in the VDSL2/ ADSL/ADSL2 and ADSL2+ channel configuration Profile Table (xdsl2ChConfProfileTable) that applies to DSL bearer channel #4. If the channel is unused, then the obj…	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.2.1.10.251.1.5.1.1.1.12
xdsl2LConfTempChan4RaRatioDs Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #4 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Min…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.251.1.5.1.1.1.13
xdsl2LConfTempChan4RaRatioUs Rate Adaptation Ratio. The ratio (in percent) that should be taken into account for the bearer channel #4 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minim…	percentUnsigned32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.251.1.5.1.1.1.14
xdsl2LConfTempRowStatus This object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. Before a profile can be deleted or taken out of service (by setti…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.251.1.5.1.1.1.15

The table xdsl2LineConfProfTable contains VDSL2/ADSL/
ADSL2 and ADSL2+ line configuration profiles.
          
Entries in this table MUST be maintained in a persistent
manner.

xdsl2LineConfProfEntry row .1.3.6.1.2.1.10.251.1.5.1.2.1

A default profile with an index of 'DEFVAL' will always
exist, and its parameters will be set to vendor-specific values,
unless otherwise specified in this document.

Indexes

xdsl2LConfProfProfileName

Column	Syntax	OID
xdsl2LConfProfProfileName This object identifies a row in this table.	OctetString Constraints: range: 1-32	.1.3.6.1.2.1.10.251.1.5.1.2.1.1
xdsl2LConfProfScMaskDs Subcarrier mask. A bitmap of 4096 bits that allows masking up to 4096 downstream subcarriers. If bit i (0 <= i < NSCds) is set to '1', the respective downstream subcarrier is masked, and if set to '0', the respective …	VDSL2-LINE-TC-MIBXdsl2ScMaskDsr/w Type Constraints: range: 0..512	.1.3.6.1.2.1.10.251.1.5.1.2.1.2
xdsl2LConfProfScMaskUs Subcarrier mask. A bitmap of 4096 bits that allows masking up to 4096 upstream subcarriers. If bit i (0 <= i < NSCus) is set to '1', the respective upstream subcarrier is masked, and if set to '0', the respective subc…	VDSL2-LINE-TC-MIBXdsl2ScMaskUsr/w Type Constraints: range: 0..512	.1.3.6.1.2.1.10.251.1.5.1.2.1.3
xdsl2LConfProfVdsl2CarMask VDSL2-specific subcarrier mask. This configuration parameter defines the restrictions, additional to the band plan, to determine the set of subcarriers allowed for transmission in both the upstream and downstream direc…	VDSL2-LINE-TC-MIBXdsl2CarMaskr/w Type Constraints: range: 0..128	.1.3.6.1.2.1.10.251.1.5.1.2.1.4
xdsl2LConfProfRfiBands For ITU-T Recommendation G.992.5, this configuration parameter defines the subset of downstream PSD mask breakpoints, as specified in xdsl2LConfProfPsdMaskDs (PSDMASKds), that shall be used to notch an RFI band. This s…	VDSL2-LINE-TC-MIBXdsl2RfiBandsr/w Type Constraints: range: 0..64	.1.3.6.1.2.1.10.251.1.5.1.2.1.5
xdsl2LConfProfRaModeDs The mode of operation of a rate-adaptive xTU-C in the transmit direction.	VDSL2-LINE-TC-MIBXdsl2RaModer/w Type Values: 1 manual 2 raInit 3 dynamicRa	.1.3.6.1.2.1.10.251.1.5.1.2.1.6
xdsl2LConfProfRaModeUs The mode of operation of a rate-adaptive xTU-R in the transmit direction.	VDSL2-LINE-TC-MIBXdsl2RaModer/w Type Values: 1 manual 2 raInit 3 dynamicRa	.1.3.6.1.2.1.10.251.1.5.1.2.1.7
xdsl2LConfProfRaUsNrmDs The Downstream Up-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. If the downstream noise margin is above this value, and stays above it, for more than the time specified by the …	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.251.1.5.1.2.1.8
xdsl2LConfProfRaUsNrmUs The Upstream Up-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. If the upstream noise margin is above this value, and stays above it, for more than the time specified by the xdsl…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.251.1.5.1.2.1.9
xdsl2LConfProfRaUsTimeDs The Downstream Up-Shift Time Interval, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. The interval of time that the downstream noise margin should stay above the Downstream Up-Shift Noise Margin before t…	secondsUnsigned32r/w Constraints: range: 0-16383	.1.3.6.1.2.1.10.251.1.5.1.2.1.10
xdsl2LConfProfRaUsTimeUs The Upstream Up-Shift Time Interval, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. The interval of time the upstream noise margin should stay above the Upstream Up-Shift Noise Margin before the xTU-C sh…	secondsUnsigned32r/w Constraints: range: 0-16383	.1.3.6.1.2.1.10.251.1.5.1.2.1.11
xdsl2LConfProfRaDsNrmDs The Downstream Down-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. If the downstream noise margin is below this value and stays below that value, for more than the time specifie…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.251.1.5.1.2.1.12
xdsl2LConfProfRaDsNrmUs The Upstream Downshift Noise Margin value, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. If the upstream noise margin is below this value and stays below that value, for more than the time specified by …	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.251.1.5.1.2.1.13
xdsl2LConfProfRaDsTimeDs The Downstream Downshift Time Interval, to be used when xdsl2LConfProfRaModeDs is set to 'dynamicRa'. The interval of time the downstream noise margin should stay below the Downstream Down-Shift Noise Margin before the…	secondsUnsigned32r/w Constraints: range: 0-16383	.1.3.6.1.2.1.10.251.1.5.1.2.1.14
xdsl2LConfProfRaDsTimeUs The Upstream Down-Shift Time Interval, to be used when xdsl2LConfProfRaModeUs is set to 'dynamicRa'. The interval of time the upstream noise margin should stay below the Upstream Down-Shift Noise Margin before the xTU-…	secondsUnsigned32r/w Constraints: range: 0-16383	.1.3.6.1.2.1.10.251.1.5.1.2.1.15
xdsl2LConfProfTargetSnrmDs The minimum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 31…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.251.1.5.1.2.1.16
xdsl2LConfProfTargetSnrmUs The minimum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 …	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.251.1.5.1.2.1.17
xdsl2LConfProfMaxSnrmDs The maximum Noise Margin the xTU-R receiver shall try to sustain. If the Noise Margin is above this level, the xTU-R shall request that the xTU-C reduce the xTU-C transmit power to get a noise margin below this limit (…	0.1 dBUnsigned32r/w Constraints: range: 0-310 range: 2147483647-2147483647	.1.3.6.1.2.1.10.251.1.5.1.2.1.18
xdsl2LConfProfMaxSnrmUs The maximum Noise Margin the xTU-C receiver shall try to sustain. If the Noise Margin is above this level, the xTU-C shall request that the xTU-R reduce the xTU-R transmit power to get a noise margin below this limit (…	0.1 dBUnsigned32r/w Constraints: range: 0-310 range: 2147483647-2147483647	.1.3.6.1.2.1.10.251.1.5.1.2.1.19
xdsl2LConfProfMinSnrmDs The minimum Noise Margin the xTU-R receiver shall tolerate. If the noise margin falls below this level, the xTU-R shall request that the xTU-C increase the xTU-C transmit power. If an increase to xTU-C transmit power is…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.251.1.5.1.2.1.20
xdsl2LConfProfMinSnrmUs The minimum Noise Margin the xTU-C receiver shall tolerate. If the noise margin falls below this level, the xTU-C shall request that the xTU-R increase the xTU-R transmit power. If an increase of xTU-R transmit power is…	0.1 dBUnsigned32r/w Constraints: range: 0-310	.1.3.6.1.2.1.10.251.1.5.1.2.1.21
xdsl2LConfProfMsgMinUs Minimum Overhead Rate Upstream. Defines the minimum rate of the message-based overhead that shall be maintained by the xTU in upstream direction. Expressed in bits per second and ranges from 4000 to 248000 bits/s.	bits/secondUnsigned32r/w Constraints: range: 4000-248000	.1.3.6.1.2.1.10.251.1.5.1.2.1.22
xdsl2LConfProfMsgMinDs Minimum Overhead Rate Downstream. Defines the minimum rate of the message-based overhead that shall be maintained by the xTU in the downstream direction. Expressed in bits per second and ranges from 4000 to 248000 bit…	bits/secondUnsigned32r/w Constraints: range: 4000-248000	.1.3.6.1.2.1.10.251.1.5.1.2.1.23
xdsl2LConfProfCeFlag This parameter is a bit that enables the use of the optional cyclic extension values.	VDSL2-LINE-TC-MIBXdsl2LineCeFlagr/w Type Values: 0 enableCyclicExtension	.1.3.6.1.2.1.10.251.1.5.1.2.1.24
xdsl2LConfProfSnrModeDs This parameter enables the transmitter-referred virtual noise in the downstream direction.	VDSL2-LINE-TC-MIBXdsl2LineSnrModer/w Type Values: 1 virtualNoiseDisabled 2 virtualNoiseEnabled	.1.3.6.1.2.1.10.251.1.5.1.2.1.25
xdsl2LConfProfSnrModeUs This parameter enables the transmitter-referred virtual noise in the upstream direction.	VDSL2-LINE-TC-MIBXdsl2LineSnrModer/w Type Values: 1 virtualNoiseDisabled 2 virtualNoiseEnabled	.1.3.6.1.2.1.10.251.1.5.1.2.1.26
xdsl2LConfProfTxRefVnDs This configuration parameter defines the downstream transmitter-referred virtual noise. The TXREFVNds shall be specified through a set of breakpoints. Each breakpoint shall consist of a subcarrier index t, with a subcar…	VDSL2-LINE-TC-MIBXdsl2LineTxRefVnDsr/w Type Constraints: range: 0..96	.1.3.6.1.2.1.10.251.1.5.1.2.1.27
xdsl2LConfProfTxRefVnUs This configuration parameter defines the upstream transmitter-referred virtual noise. The TXREFVNus shall be specified through a set of breakpoints. Each breakpoint shall consist of a subcarrier index t, with a subcarri…	VDSL2-LINE-TC-MIBXdsl2LineTxRefVnUsr/w Type Constraints: range: 0..48	.1.3.6.1.2.1.10.251.1.5.1.2.1.28
xdsl2LConfProfXtuTransSysEna xTU Transmission System Enabling (XTSE). A list of the different coding types enabled in this profile. It is coded in a bitmap representation with 1 or more bits set. A bit set to '1' means that the xTUs may apply th…	VDSL2-LINE-TC-MIBXdsl2TransmissionModeTyper/w Type Values: 0 ansit1413 1 etsi 2 g9921PotsNonOverlapped 3 g9921PotsOverlapped 4 g9921IsdnNonOverlapped 5 g9921isdnOverlapped 6 g9921tcmIsdnNonOverlapped 7 g9921tcmIsdnOverlapped 8 g9922potsNonOverlapped 9 g9922potsOverlapped 10 g9922tcmIsdnNonOverlapped 11 g9922tcmIsdnOverlapped 12 g9921tcmIsdnSymmetric 13 reserved1 14 reserved2 15 reserved3 16 reserved4 17 reserved5 18 g9923PotsNonOverlapped 19 g9923PotsOverlapped 20 g9923IsdnNonOverlapped 21 g9923isdnOverlapped 22 reserved6 23 reserved7 24 g9924potsNonOverlapped 25 g9924potsOverlapped 26 reserved8 27 reserved9 28 g9923AnnexIAllDigNonOverlapped 29 g9923AnnexIAllDigOverlapped 30 g9923AnnexJAllDigNonOverlapped 31 g9923AnnexJAllDigOverlapped 32 g9924AnnexIAllDigNonOverlapped 33 g9924AnnexIAllDigOverlapped 34 g9923AnnexLMode1NonOverlapped 35 g9923AnnexLMode2NonOverlapped 36 g9923AnnexLMode3Overlapped 37 g9923AnnexLMode4Overlapped 38 g9923AnnexMPotsNonOverlapped 39 g9923AnnexMPotsOverlapped 40 g9925PotsNonOverlapped 41 g9925PotsOverlapped 42 g9925IsdnNonOverlapped 43 g9925isdnOverlapped 44 reserved10 45 reserved11 46 g9925AnnexIAllDigNonOverlapped 47 g9925AnnexIAllDigOverlapped 48 g9925AnnexJAllDigNonOverlapped 49 g9925AnnexJAllDigOverlapped 50 g9925AnnexMPotsNonOverlapped 51 g9925AnnexMPotsOverlapped 52 reserved12 53 reserved13 54 reserved14 55 reserved15 56 g9932AnnexA 57 g9932AnnexB 58 g9932AnnexC 59 reserved16 60 reserved17 61 reserved18 62 reserved19 63 reserved20	.1.3.6.1.2.1.10.251.1.5.1.2.1.29
xdsl2LConfProfPmMode Power management state Enabling (PMMode). Defines the power states the xTU-C or xTU-R may autonomously transition to on this line. This is a set of bits, where any bit with a '1' value means that the xTU is allowed to …	VDSL2-LINE-TC-MIBXdsl2LinePmModer/w Type Values: 0 allowTransitionsToIdle 1 allowTransitionsToLowPower	.1.3.6.1.2.1.10.251.1.5.1.2.1.30
xdsl2LConfProfL0Time The minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds.	secondsUnsigned32r/w Constraints: range: 0-255	.1.3.6.1.2.1.10.251.1.5.1.2.1.31
xdsl2LConfProfL2Time The minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 state. It ranges from 0 to 255 seconds.	secondsUnsigned32r/w Constraints: range: 0-255	.1.3.6.1.2.1.10.251.1.5.1.2.1.32
xdsl2LConfProfL2Atpr The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB.	dBUnsigned32r/w Constraints: range: 0-31	.1.3.6.1.2.1.10.251.1.5.1.2.1.33
xdsl2LConfProfL2Atprt The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Requests (i.e., at transition of L0 to L2 state) and Power Trims.	dBUnsigned32r/w Constraints: range: 0-31	.1.3.6.1.2.1.10.251.1.5.1.2.1.34
xdsl2LConfProfProfiles The configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. It is coded in a bitmap representation (0 if not allowed, 1 if allowed).	VDSL2-LINE-TC-MIBXdsl2LineProfilesr/w Type Values: 0 profile8a 1 profile8b 2 profile8c 3 profile8d 4 profile12a 5 profile12b 6 profile17a 7 profile30a	.1.3.6.1.2.1.10.251.1.5.1.2.1.35
xdsl2LConfProfDpboEPsd This configuration parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as xdsl2LConfProfPsdMaskDs (PSDMASKds). The maximum number of breakpoints for …	VDSL2-LINE-TC-MIBXdsl2PsdMaskDsr/w Type Constraints: range: 0..96	.1.3.6.1.2.1.10.251.1.5.1.2.1.36
xdsl2LConfProfDpboEsEL This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectr…	0.5 dBUnsigned32r/w Constraints: range: 0-511	.1.3.6.1.2.1.10.251.1.5.1.2.1.37
xdsl2LConfProfDpboEsCableModelA The E-side Cable Model parameter A (DPBOESCMA) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally …	2^-8Unsigned32r/w Constraints: range: 0-640	.1.3.6.1.2.1.10.251.1.5.1.2.1.38
xdsl2LConfProfDpboEsCableModelB The E-side Cable Model parameter B (DPBOESCMB) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally …	2^-8Unsigned32r/w Constraints: range: 0-640	.1.3.6.1.2.1.10.251.1.5.1.2.1.39
xdsl2LConfProfDpboEsCableModelC The E-side Cable Model parameter C (DPBOESCMC) of the cable model (DPBOESCM) for cables connecting exchange-based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally …	2^-8Unsigned32r/w Constraints: range: 0-640	.1.3.6.1.2.1.10.251.1.5.1.2.1.40
xdsl2LConfProfDpboMus This configuration parameter defines the assumed Minimum Usable receive PSD mask (in dBm/Hz) for exchange-based services, used to modify parameter xdsl2LConfProfDpboFMax (DPBOFMAX) defined below (to determine the DPBO).…	0.5 dBm/HzUnsigned32r/w Constraints: range: 0-255	.1.3.6.1.2.1.10.251.1.5.1.2.1.41
xdsl2LConfProfDpboFMin This configuration parameter defines the minimum frequency from which the DPBO shall be applied. It ranges from 0 kHz (coded as 0) to 8832 kHz (coded as 2048) in steps of 4.3125 kHz. This parameter is used only for G.…	4.3125 kHzUnsigned32r/w Constraints: range: 0-2048	.1.3.6.1.2.1.10.251.1.5.1.2.1.42
xdsl2LConfProfDpboFMax This configuration parameter defines the maximum frequency at which DPBO may be applied. It ranges from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956) in steps of 4.3125 kHz. This parameter is used only for G.99…	4.3125 kHzUnsigned32r/w Constraints: range: 32-6956	.1.3.6.1.2.1.10.251.1.5.1.2.1.43
xdsl2LConfProfUpboKL This configuration parameter defines the electrical length expressed in dB at 1 MHz, kl0, configured by the CO-MIB. The value ranges from 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. This parameter is r…	0.1 dBUnsigned32r/w Constraints: range: 0-1280	.1.3.6.1.2.1.10.251.1.5.1.2.1.44
xdsl2LConfProfUpboKLF Defines the upstream power backoff force mode.	VDSL2-LINE-TC-MIBXdsl2UpboKLFr/w Type Values: 1 auto 2 override 3 disableUpbo	.1.3.6.1.2.1.10.251.1.5.1.2.1.45
xdsl2LConfProfUs0Mask The configuration parameter contains the US0 PSD masks to be allowed by the near-end xTU on the line. This parameter is only defined for G.993.2 Annex A. It is represented as a bitmap (0 if not allowed and 1 if allowe…	VDSL2-LINE-TC-MIBXdsl2LineUs0Maskr/w Type Values: 0 eu32 1 eu36 2 eu40 3 eu44 4 eu48 5 eu52 6 eu56 7 eu60 8 eu64 9 eu128 10 reserved1 11 reserved2 12 reserved3 13 reserved4 14 reserved5 15 reserved6 16 adlu32 17 adlu36 18 adlu40 19 adlu44 20 adlu48 21 adlu52 22 adlu56 23 adlu60 24 adlu64 25 adlu128 26 reserved7 27 reserved8 28 reserved9 29 reserved10 30 reserved11 31 reserved12	.1.3.6.1.2.1.10.251.1.5.1.2.1.46
xdsl2LConfProfForceInp This parameter, when set to 'true' indicates that the framer settings of the bearer shall be selected such that the impulse noise protection computed according to the formula specified in the relevant Recommendation is …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.251.1.5.1.2.1.47
xdsl2LConfProfRowStatus This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. Before a profile can be deleted or t…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.251.1.5.1.2.1.48