t38vismDs1Number
CISCO-WAN-T38-FAXRELAY-MIB ·
.1.3.6.1.4.1.351.150.19.1.1.1.1.1
Object
column
Integer32
This object identifies the unique DS1 value for a T1/E1 interface.
Context
- MIB
- CISCO-WAN-T38-FAXRELAY-MIB
- OID
.1.3.6.1.4.1.351.150.19.1.1.1.1.1- Type
- column
- Access
- noaccess
- Status
- current
- Parent
- t38FaxRelayGrpEntry
- Table
- t38FaxRelayGrpTable
- Siblings
- 14
Syntax
Integer32
Values & Constraints
Object Constraints
range: 1-2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| t38NSFCountryCode The Country Code in the NSF code is a
single-byte field identifying the country where
the group 3 fax equipment with non-standard
capabilities were manufactured.
… | column | Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.10 |
| t38NSFVendorCode The Vendor Code (also called the Terminal
Provider Code) in the NSF code is a two-byte
field identifying the manufacturer of the group
3 fax equipment with non-standard capabilit… | column | Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.11 |
| t38NseAckTimeOut This object defines a timeout value in milliseconds for a
provision able timer. This timer is started after sending a
NSE(Named Signal Event) 200 while waiting for the NSE 201
ac… | column | milliseconds Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.12 |
| t38FxLCO This object is a configurable default value for the
fx(fax option) in LCO(Local Connection Option). In
the absence of the MGCP fx LCO, this default value
will be used. The MGCP … | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.13 |
| t38Redundancy deprecated This object is used to enable/disable the Redundancy
scheme for UDP-based fax transport. | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.14 |
| t38T30ECM This object is used to enable/disable T.30
Error Correcting Mode(ECM). ECM is a feature
implemented by many new fax devices which
improves image quality and page compression
cap… | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.15 |
| t38MaxFaxTxRate This object is used for configuring the maximum fax
transmission rate.
'fx2400bps' - maximum transmission rate in 2400 bps.
'fx4800bps' - maximum transmission rat… | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.2 |
| t38FaxInfoFieldSize deprecated This object is used to configure the fax information
field size in bytes. | column | Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.3 |
| t38HsDataPacketSize This object specifies the size of primary high speed(HS)
- the data packet transmitted after the first phase of a T.38
call.
'tenms' - size of the HS in 10 milli… | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.4 |
| t38LsDataRedundancy This object determines the extent of the internet fax
protocol(IFP) packet transmission redundancy for the
low-speed control information exchanged during the
first phase of a T.3… | column | Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.5 |
| t38HsDataRedundancy This object determines the extent of the IFP packet
transmission redundancy for the high-speed control
and image information exchanged following the initial
low-speed phase of… | column | Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.6 |
| t38TCFmethod This object determines the method used to verify
the TCF(Training Check Field).
For UDP-based fax transport, its value should be set
to networkTCF. For TCP-based … | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.7 |
| t38ErrCorrection deprecated This object is used to enable/disable the FEC
scheme for UDP-based fax transport. | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.8 |
| t38NSFOverride This object is used to enable/disable the gateway to
override the NSF(Non-Standard Facilities) code in the
following T.30 signals: NSF, NSC (Non-Standard Facilities
Command) and … | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.9 |