CISCO-WAN-T38-FAXRELAY-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
1
Rows
1
Columns
15

t38FaxRelayGrpTable

table
.1.3.6.1.4.1.351.150.19.1.1.1 · 1 row entry · 15 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk t38FaxRelayGrpTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-WAN-T38-FAXRELAY-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-WAN-T38-FAXRELAY-MIB::t38FaxRelayGrpTable' 
This table contains configuration information
about various fax relay parameters used in
VoIP calls on voice interface.
t38FaxRelayGrpEntry row .1.3.6.1.4.1.351.150.19.1.1.1.1
An entry is created when a DS1 interface is
configured. An entry is deleted when a DS1
interface is removed. All configurations
information in an entry is applied to a VoIP
call when the VoIP call is placed on the D…
Indexes
Column Syntax OID
t38vismDs1Number
This object identifies the unique DS1 value for
a T1/E1 interface.
Integer32
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.351.150.19.1.1.1.1.1
t38MaxFaxTxRate
This object is used for configuring the maximum fax
transmission rate.

'fx2400bps' - maximum transmission rate in 2400 bps.
'fx4800bps' - maximum transmission rate in 4800 bps.
'fx7200bps' - maximum tr…
Enumerationr/w
Enumerated Values:
1fx2400bps
2fx4800bps
3fx7200bps
4fx9600bps
5fx12000bps
6fx14400bps
 .1.3.6.1.4.1.351.150.19.1.1.1.1.2
t38FaxInfoFieldSizedeprecated
This object is used to configure the fax information
field size in bytes.
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.150.19.1.1.1.1.3
t38HsDataPacketSize
This object specifies the size of primary high speed(HS)
- the data packet transmitted after the first phase of a T.38
call.

'tenms' - size of the HS in 10 millisecond.
'twentyms' - size of the HS in …
Enumerationr/w
Enumerated Values:
10tenms
20twentyms
30thirtyms
40fortyms
 .1.3.6.1.4.1.351.150.19.1.1.1.1.4
t38LsDataRedundancy
This object determines the extent of the internet fax
protocol(IFP) packet transmission redundancy for the
low-speed control information exchanged during the
first phase of a T.38 fax relay connection.

…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.150.19.1.1.1.1.5
t38HsDataRedundancy
This object determines the extent of the IFP packet
transmission redundancy for the high-speed control
and image information exchanged following the initial
low-speed phase of a T.38 fax relay connection.
…
Integer32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.351.150.19.1.1.1.1.6
t38TCFmethod
This object determines the method used to verify
the TCF(Training Check Field).

For UDP-based fax transport, its value should be set
to networkTCF. For TCP-based fax transport, its value
should be set …
Enumerationr/w
Enumerated Values:
1localTCF
2networkTCF
 .1.3.6.1.4.1.351.150.19.1.1.1.1.7
t38ErrCorrectiondeprecated
This object is used to enable/disable the FEC
scheme for UDP-based fax transport.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.351.150.19.1.1.1.1.8
t38NSFOverride
This object is used to enable/disable the gateway to
override the NSF(Non-Standard Facilities) code in the
following T.30 signals: NSF, NSC (Non-Standard Facilities
Command) and NSS (Non-Standard Facilities Set-up). Th…
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.351.150.19.1.1.1.1.9
t38NSFCountryCode
The Country Code in the NSF code is a
single-byte field identifying the country where
the group 3 fax equipment with non-standard
capabilities were manufactured.

There are un ratified proposals on the …
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.351.150.19.1.1.1.1.10
t38NSFVendorCode
The Vendor Code (also called the Terminal
Provider Code) in the NSF code is a two-byte
field identifying the manufacturer of the group
3 fax equipment with non-standard capabilities.

If the fax relay ca…
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.351.150.19.1.1.1.1.11
t38NseAckTimeOut
This object defines a timeout value in milliseconds for a
provision able timer. This timer is started after sending a
NSE(Named Signal Event) 200 while waiting for the NSE 201
acknowledgement or NSE 202 negative acknow…
millisecondsInteger32r/w
Constraints:
range: 250-10000
 .1.3.6.1.4.1.351.150.19.1.1.1.1.12
t38FxLCO
This object is a configurable default value for the
fx(fax option) in LCO(Local Connection Option). In
the absence of the MGCP fx LCO, this default value
will be used. The MGCP fx LCO will always override
this object.…
Enumerationr/w
Enumerated Values:
1gwAndPt
2gw
3ptAndGw
4pt
5off
 .1.3.6.1.4.1.351.150.19.1.1.1.1.13
t38Redundancydeprecated
This object is used to enable/disable the Redundancy
scheme for UDP-based fax transport.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.351.150.19.1.1.1.1.14
t38T30ECM
This object is used to enable/disable T.30
Error Correcting Mode(ECM). ECM is a feature
implemented by many new fax devices which
improves image quality and page compression
capabilities through a reliable image data …
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.351.150.19.1.1.1.1.15