t38NseAckTimeOut

Object

column r/w milliseconds Integer32

This object defines a timeout value in milliseconds for a 
provision able timer. This timer is started after sending a
NSE(Named Signal Event) 200 while waiting for the NSE 201
acknowledgement or NSE 202 negative acknowledgement.
Expiration of the response timer will indicate that the
request to switch to T.38 has been rejected or discarded
by the far end. 
              
The default value is 1 second (1000 ms) and this value
can only be set in the increments of 250 ms.

Context

MIB: CISCO-WAN-T38-FAXRELAY-MIB
OID: .1.3.6.1.4.1.351.150.19.1.1.1.1.12
Type: column
Access: readwrite
Status: current
Units: milliseconds
Parent: t38FaxRelayGrpEntry
Table: t38FaxRelayGrpTable
Siblings: 14

Related Objects

Sibling Objects

Object	Type	Syntax	OID
t38vismDs1Number This object identifies the unique DS1 value for a T1/E1 interface.	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.1`
t38NSFCountryCode The Country Code in the NSF code is a single-byte field identifying the country where the group 3 fax equipment with non-standard capabilities were manufactured. …	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.10`
t38NSFVendorCode The Vendor Code (also called the Terminal Provider Code) in the NSF code is a two-byte field identifying the manufacturer of the group 3 fax equipment with non-standard capabilit…	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.11`
t38FxLCO This object is a configurable default value for the fx(fax option) in LCO(Local Connection Option). In the absence of the MGCP fx LCO, this default value will be used. The MGCP …	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.13`
t38Redundancy deprecated This object is used to enable/disable the Redundancy scheme for UDP-based fax transport.	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.14`
t38T30ECM This object is used to enable/disable T.30 Error Correcting Mode(ECM). ECM is a feature implemented by many new fax devices which improves image quality and page compression cap…	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.15`
t38MaxFaxTxRate This object is used for configuring the maximum fax transmission rate. 'fx2400bps' - maximum transmission rate in 2400 bps. 'fx4800bps' - maximum transmission rat…	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.2`
t38FaxInfoFieldSize deprecated This object is used to configure the fax information field size in bytes.	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.3`
t38HsDataPacketSize This object specifies the size of primary high speed(HS) - the data packet transmitted after the first phase of a T.38 call. 'tenms' - size of the HS in 10 milli…	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.4`
t38LsDataRedundancy This object determines the extent of the internet fax protocol(IFP) packet transmission redundancy for the low-speed control information exchanged during the first phase of a T.3…	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.5`
t38HsDataRedundancy This object determines the extent of the IFP packet transmission redundancy for the high-speed control and image information exchanged following the initial low-speed phase of…	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.6`
t38TCFmethod This object determines the method used to verify the TCF(Training Check Field). For UDP-based fax transport, its value should be set to networkTCF. For TCP-based …	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.7`
t38ErrCorrection deprecated This object is used to enable/disable the FEC scheme for UDP-based fax transport.	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.8`
t38NSFOverride This object is used to enable/disable the gateway to override the NSF(Non-Standard Facilities) code in the following T.30 signals: NSF, NSC (Non-Standard Facilities Command) and …	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.9`

Object

Context

Syntax

Values & Constraints

Related Objects