t38MaxFaxTxRate

CISCO-WAN-T38-FAXRELAY-MIB · .1.3.6.1.4.1.351.150.19.1.1.1.1.2

MIB view Table view

Object

column r/w Enumeration

This object is used for configuring the maximum fax
transmission rate.
              
'fx2400bps'  - maximum transmission rate in 2400 bps.
'fx4800bps'  - maximum transmission rate in 4800 bps.
'fx7200bps'  - maximum transmission rate in 7200 bps.
'fx9600bps'  - maximum transmission rate in 9600 bps.
'fx12000bps' - maximum transmission rate in 12000 bps. 
'fx14400bps' - maximum transmission rate in 14400 bps.

Context

MIB: CISCO-WAN-T38-FAXRELAY-MIB
OID: .1.3.6.1.4.1.351.150.19.1.1.1.1.2
Type: column
Access: readwrite
Status: current
Parent: t38FaxRelayGrpEntry
Table: t38FaxRelayGrpTable
Siblings: 14

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	fx2400bps
`2`	fx4800bps
`3`	fx7200bps
`4`	fx9600bps
`5`	fx12000bps
`6`	fx14400bps

Related Objects

Sibling Objects

Object	Type	Syntax	OID
t38vismDs1Number This object identifies the unique DS1 value for a T1/E1 interface.	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.1`
t38NSFCountryCode The Country Code in the NSF code is a single-byte field identifying the country where the group 3 fax equipment with non-standard capabilities were manufactured. …	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.10`
t38NSFVendorCode The Vendor Code (also called the Terminal Provider Code) in the NSF code is a two-byte field identifying the manufacturer of the group 3 fax equipment with non-standard capabilit…	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.11`
t38NseAckTimeOut This object defines a timeout value in milliseconds for a provision able timer. This timer is started after sending a NSE(Named Signal Event) 200 while waiting for the NSE 201 ac…	column	milliseconds Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.12`
t38FxLCO This object is a configurable default value for the fx(fax option) in LCO(Local Connection Option). In the absence of the MGCP fx LCO, this default value will be used. The MGCP …	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.13`
t38Redundancy deprecated This object is used to enable/disable the Redundancy scheme for UDP-based fax transport.	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.14`
t38T30ECM This object is used to enable/disable T.30 Error Correcting Mode(ECM). ECM is a feature implemented by many new fax devices which improves image quality and page compression cap…	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.15`
t38FaxInfoFieldSize deprecated This object is used to configure the fax information field size in bytes.	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.3`
t38HsDataPacketSize This object specifies the size of primary high speed(HS) - the data packet transmitted after the first phase of a T.38 call. 'tenms' - size of the HS in 10 milli…	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.4`
t38LsDataRedundancy This object determines the extent of the internet fax protocol(IFP) packet transmission redundancy for the low-speed control information exchanged during the first phase of a T.3…	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.5`
t38HsDataRedundancy This object determines the extent of the IFP packet transmission redundancy for the high-speed control and image information exchanged following the initial low-speed phase of…	column	Integer32	`.1.3.6.1.4.1.351.150.19.1.1.1.1.6`
t38TCFmethod This object determines the method used to verify the TCF(Training Check Field). For UDP-based fax transport, its value should be set to networkTCF. For TCP-based …	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.7`
t38ErrCorrection deprecated This object is used to enable/disable the FEC scheme for UDP-based fax transport.	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.8`
t38NSFOverride This object is used to enable/disable the gateway to override the NSF(Non-Standard Facilities) code in the following T.30 signals: NSF, NSC (Non-Standard Facilities Command) and …	column	Enumeration	`.1.3.6.1.4.1.351.150.19.1.1.1.1.9`