t38HsDataRedundancy
CISCO-WAN-T38-FAXRELAY-MIB ·
.1.3.6.1.4.1.351.150.19.1.1.1.1.6
Object
column
r/w
Integer32
This object determines the extent of the IFP packet
transmission redundancy for the high-speed control
and image information exchanged following the initial
low-speed phase of a T.38 fax relay connection.
Depending on whether FEC is enabled via the
t38ErrorCorrection object, t38HsDataRedundancy
has different meanings.
If FEC is disabled, then t38HsDataRedundancy is the
maximum number of prior IFP packets within a UDPTL packet
carrying high speed information, not counting the primary
or current IFP packet.
If FEC is enabled, then t38HsDataRedundancy is the
maximum number of FEC messages within a UDPTL packet
carrying high speed information.
Context
- MIB
- CISCO-WAN-T38-FAXRELAY-MIB
- OID
.1.3.6.1.4.1.351.150.19.1.1.1.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- t38FaxRelayGrpEntry
- Table
- t38FaxRelayGrpTable
- Siblings
- 14
Syntax
Integer32
Values & Constraints
Object Constraints
range: 0-2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| t38vismDs1Number This object identifies the unique DS1 value for
a T1/E1 interface. | column | Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.1 |
| t38NSFCountryCode The Country Code in the NSF code is a
single-byte field identifying the country where
the group 3 fax equipment with non-standard
capabilities were manufactured.
… | column | Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.10 |
| t38NSFVendorCode The Vendor Code (also called the Terminal
Provider Code) in the NSF code is a two-byte
field identifying the manufacturer of the group
3 fax equipment with non-standard capabilit… | column | Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.11 |
| t38NseAckTimeOut This object defines a timeout value in milliseconds for a
provision able timer. This timer is started after sending a
NSE(Named Signal Event) 200 while waiting for the NSE 201
ac… | column | milliseconds Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.12 |
| t38FxLCO This object is a configurable default value for the
fx(fax option) in LCO(Local Connection Option). In
the absence of the MGCP fx LCO, this default value
will be used. The MGCP … | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.13 |
| t38Redundancy deprecated This object is used to enable/disable the Redundancy
scheme for UDP-based fax transport. | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.14 |
| t38T30ECM This object is used to enable/disable T.30
Error Correcting Mode(ECM). ECM is a feature
implemented by many new fax devices which
improves image quality and page compression
cap… | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.15 |
| t38MaxFaxTxRate This object is used for configuring the maximum fax
transmission rate.
'fx2400bps' - maximum transmission rate in 2400 bps.
'fx4800bps' - maximum transmission rat… | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.2 |
| t38FaxInfoFieldSize deprecated This object is used to configure the fax information
field size in bytes. | column | Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.3 |
| t38HsDataPacketSize This object specifies the size of primary high speed(HS)
- the data packet transmitted after the first phase of a T.38
call.
'tenms' - size of the HS in 10 milli… | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.4 |
| t38LsDataRedundancy This object determines the extent of the internet fax
protocol(IFP) packet transmission redundancy for the
low-speed control information exchanged during the
first phase of a T.3… | column | Integer32 | .1.3.6.1.4.1.351.150.19.1.1.1.1.5 |
| t38TCFmethod This object determines the method used to verify
the TCF(Training Check Field).
For UDP-based fax transport, its value should be set
to networkTCF. For TCP-based … | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.7 |
| t38ErrCorrection deprecated This object is used to enable/disable the FEC
scheme for UDP-based fax transport. | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.8 |
| t38NSFOverride This object is used to enable/disable the gateway to
override the NSF(Non-Standard Facilities) code in the
following T.30 signals: NSF, NSC (Non-Standard Facilities
Command) and … | column | Enumeration | .1.3.6.1.4.1.351.150.19.1.1.1.1.9 |