cpwVcEnetPortIfIndex

CISCO-IETF-PW-ENET-MIB · .1.3.6.1.4.1.9.10.108.1.1.1.5
Commands MIB view Table view

Object

column r/w IF-MIBInterfaceIndexOrZero 
This object is used to specify the ifIndex of the ETHERNET 
port associated with this VC for point-to-point Ethernet  
service, or the ifIndex of the virtual interface of the VPLS  
instance associated with the PW if the service is VPLS. Two  
rows in this table can point to the same ifIndex only if: 
              
1) It is required to support multiple COS on a MPLS PSN  
   for the same service (i.e.: a combination of ports and  
   VLANs) by the use of multiple VC, each with a different 
   COS. 
              
2) There is no overlap of VLAN values specified in  
   cpwVcEnetPortVlan that are associated with this port. 
              
A value of zero indicate that association to an ifIndex is 
not yet known.

Context

MIB
CISCO-IETF-PW-ENET-MIB
OID
.1.3.6.1.4.1.9.10.108.1.1.1.5
Type
column
Access
readwrite
Status
current
Parent
cpwVcEnetEntry
Groups
1

Net-SNMP examples

How SNMP and these commands work

Walk the column to discover its indexed instances, or supply every index to read one instance.

Walk the column
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-IETF-PW-ENET-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-IETF-PW-ENET-MIB::cpwVcEnetPortIfIndex'
More examples
Read one indexed instance
/usr/bin/snmpget -v2c -c '<community>' -Pud -Ir -OQUv -m 'CISCO-IETF-PW-ENET-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-IETF-PW-ENET-MIB::cpwVcEnetPortIfIndex.<cpwVcIndex>.<cpwVcEnetPwVlan>'
Translate to a numeric OID
/usr/bin/snmptranslate -Pud -Ir -On -m 'CISCO-IETF-PW-ENET-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'CISCO-IETF-PW-ENET-MIB::cpwVcEnetPortIfIndex'

Syntax

IF-MIBInterfaceIndexOrZero
Source
IF-MIBInterfaceIndexOrZero
Base type
Integer32
Display format
d
Type Description
This textual convention is an extension of the
InterfaceIndex convention.  The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system.  This extension permits the
additional value of zero.  the value zero is object-specific
and must therefore be defined as part of the description of
any object which uses this syntax.  Examples of the usage of
zero might include situations where interface was unknown,
or when none or all interfaces need to be referenced.

Values & Constraints

Type Constraints
range: 0..2147483647

Conformance

Member of
cpwVcEnetGroup