ZTE-AN-PON-REMOTE-ONU-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
15
Rows
15
Columns
140

zxAnPonRmOnuIfProtoConfTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.1.5 · 1 row entry · 3 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuIfProtoConfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuIfProtoConfTable' 
This table includes protocol configuration 
information of ONU's Ethernet UNI port.
zxAnPonRmOnuIfProtoConfEntry row .1.3.6.1.4.1.3902.1082.500.3.2.1.5.1
An entry in zxAnPonRmOnuIfProtoConfTable.this is not available
Indexes
Column Syntax OID
zxAnPonRmOnuIfIndex
This attribute specifies the index of ONU's interface.
ZTE-AN-PON-TC-MIBZxAnPonRmOnuIfIndex
Description:
ZxAnPonRmOnuIfIndex reprensents the index of interface in ONU.
The definition is as follows:
| MSB Byte 4 | Byte 3 | Byte 2 | Byte 1 LSB |
| Type | Reserved | …
 .1.3.6.1.4.1.3902.1082.500.3.2.1.5.1.1
zxAnPonRmOnuIfProtoPktsLimitPrf
Refers to 'zxAnPonRmProtoPktsLimitPrfName'.
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-64
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.1.5.1.2
zxAnPonRmOnuIfProtoEnablePrf
Refers to 'zxAnPonRmProtoEnablePrfName'.
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-64
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.1.5.1.3

zxAnPonRmPotsCallDataRecordTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.2.2 · 1 row entry · 22 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmPotsCallDataRecordTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmPotsCallDataRecordTable' 
PON ONU POTS calling data record table.
zxAnPonRmPotsCallDataRecordEntry row .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1
An entry in zxAnPonRmPotsCallDataRecordTable.this is not available
Indexes
Column Syntax OID
zxAnPonRmOnuUniIndex
This attribute indicates the index of UNI in ONU.
ZTE-AN-PON-TC-MIBZxAnPonRmOnuUniIndex
Description:
ZxAnPonRmOnuUniIndex reprensents the index of UNI in ONU.

|MSB Byte 2 | Byte 1 LSB|
|------------------------------+---------------------------|
| Slot No. …
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.1
zxAnPonRmPotsCdrIndex
VoIP calling record index.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.2
zxAnPonRmPotsCdrTotalNum
The total number of the call records.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.3
zxAnPonRmPotsCdrSequenceNum
Sequence number of call record.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.4
zxAnPonRmPotsCdrTime
The time of one call,
format is yyyy-mm-dd,HH:MM:SS. For example,2010-12-30,13:06:30.
SNMPv2-TCDateAndTime
Type Constraints:
range: 8
range: 11
Description:
A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.5
zxAnPonRmPotsCdrDuration
The duration of one call.
SecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.6
zxAnPonRmPotsCdrCalleeNumber
Callee number.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.7
zxAnPonRmPotsCdrCallerNumber
Caller number.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.8
zxAnPonRmPotsCdrTxRtpPkts
The total number of
RTP packets transmitted during the call.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.9
zxAnPonRmPotsCdrRxRtpPkts
The total number of RTP packets received during the call.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.10
zxAnPonRmPotsCdrLostRtpPkts
The total number of
RTP packets lost during the call.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.11
zxAnPonRmPotsCdrDiscardRtpPkts
The total number of
RTP packets discarded due to error.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.12
zxAnPonRmPotsCdrBufOverCount
Buffer overflow count.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.13
zxAnPonRmPotsCdrBufEmptyCount
Buffer empty count.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.14
zxAnPonRmPotsCdrRxAvgJitter
The average jitter for received packets.
MillisecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.15
zxAnPonRmPotsCdrFarEndRtcp
Whether or not the
far end participated in RTCP.
Enumeration
Enumerated Values:
1participated
2notParticipated
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.16
zxAnPonRmPotsCdrRxPeakJitter
The peak jitter for received packets.
MillisecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.17
zxAnPonRmPotsCdrRxAvgJtrBufDep
The average jitter buffer depth for received packets.
MillisecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.18
zxAnPonRmPotsCdrFarEndRtcpXr
Whether or not the
far end participated in RTCP-XR.
Enumeration
Enumerated Values:
1participated
2notParticipated
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.19
zxAnPonRmPotsCdrPeakRtDelay
The peak round-trip delay for a call.
MillisecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.20
zxAnPonRmPotsCdrAvgRtDelay
The average round-trip delay for the call.
MillisecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.21
zxAnPonRmPotsCdrAvgMos
The average mean opinion score.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.2.2.1.22

zxAnPonRmOnuRetrieveCmdTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.5.3 · 1 row entry · 3 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuRetrieveCmdTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuRetrieveCmdTable' 
EMS can send zxAnPonRmOnuRetrieveCmd to retrieve ONU monitoring
metrics which are not defined by ME of OMCI or OAM.
Otherwise, EMS can retrieve error messages of excution of
zxAnPonRmOnuConfCmd  in ONU.
          
The action is divided into two steps.
Step one:
   EMS sends zxAnPonRmOnuRetrieveCmdSessionId and
   zxAnPonRmOnuRetrieveCmd to OLT.
   The format of zxAnPonRmOnuRetrieveCmd is:
   'command head::[parameter 1]=P1,[parameter 2]=P2,
    ...[parameter n]=Pn;'
   the command head represents a configuration function 
   which is defined by EMS and ONU.
   parameters are followed by '::' and separated by ',',
   the end of the command must be ';'.
   Example:
    GET_WAN_CONF::WANID=1;                 
Step two:  
   The result is saved in zxAnPonRmOnuRetrieveCmdReply.
   EMS can retrieve result by zxAnPonRmOnuRetrieveCmdSessionId.
   The format of zxAnPonRmOnuRetrieveCmdReply is:
   'command head::[parameter 1]=P1,[parameter 2]=P2,
    ...[parameter n]=Pn;'
   the command head represents a configuration function 
   which is defined by EMS and ONU.
   parameters are followed by '::' and separated by ',',
   the end of the command must be ';'.
   Example:
    GET_WAN_CONF_RESULT::WANID=1,HOST=1,MODE=1,PPPUser=test,
      PPPPassword=test;
zxAnPonRmOnuRetrieveCmdEntry row .1.3.6.1.4.1.3902.1082.500.3.2.5.3.1
An entry in zxAnPonRmOnuRetrieveCmdTable.
Indexes
Column Syntax OID
zxAnPonRmOnuRetrieveCmdSessionId
This attribute identifies the session ID.
The session ID is generated by EMS and is unique in EMS.
Session ID can ensure that reply result does not conflicting.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3902.1082.500.3.2.5.3.1.1
zxAnPonRmOnuRetrieveCmd
This attribute identifies commands
which declared the information which EMS needs.
OctetStringr/w
Constraints:
range: 0-1024
 .1.3.6.1.4.1.3902.1082.500.3.2.5.3.1.2
zxAnPonRmOnuRetrieveCmdReply
This attribute identifies the reply result.
OctetString
Constraints:
range: 0-1024
 .1.3.6.1.4.1.3902.1082.500.3.2.5.3.1.3

zxAnPonRmOnuConfFileSvrTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.6.2 · 1 row entry · 4 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuConfFileSvrTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuConfFileSvrTable' 
Service configuration  server  of the ONU.
zxAnPonRmOnuConfFileSvrEntry row .1.3.6.1.4.1.3902.1082.500.3.2.6.2.1
It is entry in the zxAnPonRmOnuConfFileSvrTable.this is not available
Indexes
Column Syntax OID
zxAnPonRmOnuConfFileSvrAddress
This attribute identifies the service configuration server address
information, along with the URI to be used for the file transfer.
The URI string should specify the protocol supported
by the ONU, an IP address or a st…
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-64
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.6.2.1.1
zxAnPonRmOnuConfFileSvrUserName
This attribute identifies the user name for service configuration
server authentication.
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-16
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.6.2.1.2
zxAnPonRmOnuConfFileSvrPassword
This attribute identifies the password for service configuration
server authentication.
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-16
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.6.2.1.3
zxAnPonRmOnuConfFileSvrFileName
This attribute identifies the service configuration file name
that the ONU download from service configuration server.
if zxAnPonRmOnuConfFileSvrAddress is't null and this attribute
is null, then it identifies that ONU…
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-32
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.6.2.1.4

zxAnPonRmWifi5gUniTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.7.6 · 1 row entry · 12 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmWifi5gUniTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmWifi5gUniTable' 
ONU 5G WiFi interface table.
zxAnPonRmWifi5gUniEntry row .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1
ONU 5G WiFi interface entry.this is not available
Indexes
Column Syntax OID
zxAnPonRmWifi5gIfAdminStatus
Enable or disable the WiFi interface function.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.1
zxAnPonRmWifi5gIfOperStatus
The operational status of WiFi interface.
Enumeration
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.2
zxAnPonRmWifi5gIfRadioMeasEnable
Enable or disable the radio measurement function.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.3
zxAnPonRmWifi5gIfIsolationEnable
Enable or disable the SSID isolation function.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.4
zxAnPonRmWifi5gIfSgiEnable
Enable or disable the SGI function.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.5
zxAnPonRmWifi5gIfWlWorkMode
The wireless work mode of WiFi interface.
The attribute is a bit map,
format as follows:
Bit 0 indicates '802.11n'
Bit 1 indicates '802.11a'
Bit 2 indicates '802.11ac'
Each bit, 0 indicates not supported, 1 indicates su…
Bitsr/w
Enumerated Values:
0ieee802for11n
1ieee802for11a
2ieee802for11ac
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.6
zxAnPonRmWifi5gIfRegulateDomain
The current regulatory domain.
The values 'mkk' and 'etsi' are only suported by EPON.
The values only supported by GPON are as follow:
'russia', 'brazil', 'egypt', 'germany', 'greece', 'hongkong',
'italy', 'korea', 'uk'…
Enumerationr/w
Enumerated Values:
1other
2usa
3canada
4etsi
5spain
6france
7mkk
8china
9russia
10brazil
11egypt
12germany
13greece
14hongkong
15italy
16korea
17uk
18portugal
19lithuania
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.7
zxAnPonRmWifi5gIfChannel
The channel of WiFi interface.
The value 0 indicates the default channel.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.8
zxAnPonRmWifi5gIfChannelBw
The channel bandwidth of WiFi interface.
Enumerationr/w
Enumerated Values:
1for20Mhz
2for40Mhz
3for80Mhz
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.9
zxAnPonRmWifi5gIfQosType
The QoS type of WiFi interface.
Enumerationr/w
Enumerated Values:
1disabled
2wmm
3ssid
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.10
zxAnPonRmWifi5gIfTxRate
This attribute defines the transmitting rate.
Enumerationr/w
Enumerated Values:
1auto
2for1Mbps
3for2Mbps
4for5Dot5Mbps
5for6Mbps
6for9Mbps
7for11Mbps
8for12Mbps
9for18Mbps
10for24Mbps
11for36Mbps
12for48Mbps
13for54Mbps
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.11
zxAnPonRmWifi5gIfTxPower
The transmitting power of WiFi interface.
Enumerationr/w
Enumerated Values:
1percent100
2percent80
3percent60
4percent40
5percent20
 .1.3.6.1.4.1.3902.1082.500.3.2.7.6.1.12

zxAnPonRmOnuCfmMdTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.8.2 · 1 row entry · 7 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuCfmMdTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuCfmMdTable' 
The Maintenance Domain table. Each row in the table
represents a different Maintenance Domain.
A Maintenance Domain is described in 802.1ag (3.22) as the
network or the part of the network for which faults in
connectivity are to be managed. The boundary of a Maintenance
Domain is defined by a set of DSAPs, each of which can become
a point of connectivity to a service instance.
This table only used by GPON service.
zxAnPonRmOnuCfmMdEntry row .1.3.6.1.4.1.3902.1082.500.3.2.8.2.1
The Maintenance Domain table entry.
The index 'zxAnPonOnuIndex' represents the normal ONU index.
Indexes
Column Syntax OID
zxAnPonRmOnuCfmMdId
The index to the Maintenance Domain table.
Referential integrity is required, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
can never be reused for other Maintenance Domain. The …
Integer32
Constraints:
range: 1-16
 .1.3.6.1.4.1.3902.1082.500.3.2.8.2.1.1
zxAnPonRmOnuCfmMdFormat
The type (and thereby format) of the Maintenance Domain Name.
A value that represents a type (and thereby the format)
of a zxAnPonRmOnuCfmMdName. The value can be one of
the following:
none(1) No format speci…
Enumerationr/w
Enumerated Values:
1none
2dnsLikeName
3macAddressAndUint
4charString
5iccBased
 .1.3.6.1.4.1.3902.1082.500.3.2.8.2.1.2
zxAnPonRmOnuCfmMdName
The Maintenance Domain name. The type/format of this object
is determined by the value of the zxAnPonRmOnuCfmMdFormat object.
Each Maintenance Domain has unique name amongst all those
used or available to a service prov…
OctetStringr/w
Constraints:
range: 0-45
 .1.3.6.1.4.1.3902.1082.500.3.2.8.2.1.3
zxAnPonRmOnuCfmMdMdLevel
The Maintenance Domain Level.
Integer identifying the Maintenance Domain Level (MD Level).
Higher numbers correspond to higher Maintenance Domains,
those with the greatest physical reach, with the highest
values for cus…
Integer32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.3902.1082.500.3.2.8.2.1.4
zxAnPonRmOnuCfmMdMhfCreation
Indicates if the Management Entity can create MHFs.
Enumerated value indicating whether the management entity can
create MHFs (MIP Half Function) for this Maintenance Domain.

The valid values are:
…
Enumerationr/w
Enumerated Values:
1defMHFnone
2defMHFdefault
3defMHFexplicit
 .1.3.6.1.4.1.3902.1082.500.3.2.8.2.1.5
zxAnPonRmOnuCfmSendIdPermission
Enumerated value indicating what, if anything, is to be
included in the Sender ID TLV (21.5.3) transmitted by MPs
configured in this Maintenance Domain. Since, in this
variable, there is no encompassing Maintenance Doma…
Enumerationr/w
Enumerated Values:
1sendIdNone
2sendIdChassis
3sendIdManage
4sendIdChassisManage
 .1.3.6.1.4.1.3902.1082.500.3.2.8.2.1.6
zxAnPonRmOnuCfmMdRowStatus
The status of the row.
The writable columns in a row can not be changed if the row
is active. All columns must have a valid value before a row
can be activated.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.3902.1082.500.3.2.8.2.1.50

zxAnPonRmOnuCfmMaTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.8.3 · 1 row entry · 8 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuCfmMaTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuCfmMaTable' 
This managed entity models an IEEE 802.1 service defined
on a bridge port. A maintenance association (MA) is
a set of endpoints on opposite sides of a network,
all existing at a defined maintenance level.
This table only used by GPON service.
zxAnPonRmOnuCfmMaEntry row .1.3.6.1.4.1.3902.1082.500.3.2.8.3.1
It is entry in the zxAnPonRmOnuCfmMaTable.
Indexes
Column Syntax OID
zxAnPonOnuCfmMaId
This attribute uniquely identifies an instance of MA.
Integer32
Constraints:
range: 1-16
 .1.3.6.1.4.1.3902.1082.500.3.2.8.3.1.1
zxAnPonOnuCfmMaNameFormat
A value that represents a type (and thereby the format)
of a zxAnPonOnuCfmMaName. The value can be one of
the following:

primaryVid(1) Primary VLAN ID.
12 bits represented in a 2-oc…
Enumerationr/w
Enumerated Values:
1primaryVid
2charString
3unsignedInt16
4rfc2865VpnId
 .1.3.6.1.4.1.3902.1082.500.3.2.8.3.1.2
zxAnPonOnuCfmMaName
Denotes a generic Maintenance Association Name. It is the
part of the Maintenance Association Identifier which is
unique within the Maintenance Domain Name and is appended
to the Maintenance Domain Name to form the Main…
OctetStringr/w
Constraints:
range: 0-45
 .1.3.6.1.4.1.3902.1082.500.3.2.8.3.1.3
zxAnPonOnuCfmMaCcmInterval
Indicates the interval at which CCMs are sent by a MEP.
The possible values are:
intervalInvalid(1) No CCMs are sent (disabled).
interval300Hz(2) CCMs are sent every 3 1/3 milliseconds
(300Hz…
Enumerationr/w
Enumerated Values:
1intervalInvalid
2interval300Hz
3interval10ms
4interval100ms
5interval1s
6interval10s
7interval1min
8interval10min
 .1.3.6.1.4.1.3902.1082.500.3.2.8.3.1.4
zxAnPonOnuCfmMaVlans
This attribute is a list of up to 12 VLAN IDs with which
this MA is associated.
The first entry is understood to be the primary VLAN.
eg: 100,15-16 means that the primary VLAN is 100, MA is associated
with VLAN 15,16,10…
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-64
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.8.3.1.5
zxAnPonOnuCfmMaMhfCreation
This attribute determines whether the bridge creates a MHF or not,
under circumstances defined in IEEE 802.1ag clause 22.2.3.
defMHFnone(1), No MHFs can be created for this VID.
defMHFdefault(2), MHFs can be created on…
Enumerationr/w
Enumerated Values:
1defMHFnone
2defMHFdefault
3defMHFexplicit
4defMHFdefer
 .1.3.6.1.4.1.3902.1082.500.3.2.8.3.1.6
zxAnPonOnuCfmMaIdPermission
This attribute determines the content of the sender ID TLV included
in CFM messages transmitted by MP controlled by this MA.
sendIdNone(1), The Sender ID TLV is not to be sent.
sendIdChassis(2), The Chassis ID Leng…
Enumerationr/w
Enumerated Values:
1sendIdNone
2sendIdChassis
3sendIdManage
4sendIdChassisManage
5sendIdDefer
 .1.3.6.1.4.1.3902.1082.500.3.2.8.3.1.7
zxAnPonOnuCfmMaRowStatus
This attribute indicates the operation of the entry.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.3902.1082.500.3.2.8.3.1.50

zxAnPonRmOnuCfmMepTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.8.4 · 1 row entry · 18 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuCfmMepTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuCfmMepTable' 
This managed entity models a maintenance association end point
(MEP) as defined primarily in IEEE 802.1ag 
 and secondarily in ITU-T Y.1731.
This table only used by GPON service.
zxAnPonRmOnuCfmMepEntry row .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1
It is entry in the zxAnPonRmOnuCfmMepTable.
Indexes
Column Syntax OID
zxAnPonOnuCfmMepId
This attribute specifies the MEP's own identity in the MA.
Integer32
Constraints:
range: 1-8191
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.1
zxAnPonOnuCfmMepEthUniId
This attribute specifies the associated Ethernet port.
ZTE-AN-PON-TC-MIBZxAnPonRmOnuUniIndexr/w
Description:
ZxAnPonRmOnuUniIndex reprensents the index of UNI in ONU.

|MSB Byte 2 | Byte 1 LSB|
|------------------------------+---------------------------|
| Slot No. …
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.2
zxAnPonOnuCfmMepCcmEnabled
If set to true, the MEP will generate CCM messages.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.3
zxAnPonOnuCfmMepServerEnable
This attribute specifies that wether to
enable Y.1731 server MEP function.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.4
zxAnPonOnuCfmMepDirection
The direction in which the MEP faces on the Bridge port.
Indicates the direction in which the Maintenance
association (MEP or MIP) faces on the bridge port:

down(1) Sends Continuity Check Messages away…
Enumerationr/w
Enumerated Values:
1down
2up
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.5
zxAnPonOnuCfmMepPrimaryVid
An integer indicating the Primary VID of the MEP, always
one of the VIDs assigned to the MEP's MA. The value 0
indicates that either the Primary VID is that of the
MEP's MA, or that the MEP's MA is associated with no V…
Integer32r/w
Constraints:
range: 0-4094
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.6
zxAnPonOnuCfmMepAdminState
Administrative state of the MEP,
unlock indicates that the MEP is to function normally, and
lock indicates that it is to cease functioning.
Enumerationr/w
Enumerated Values:
1unlock
2lock
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.7
zxAnPonOnuCfmMepPri
The priority value for CCMs and LTMs transmitted by the MEP.
Default Value is the highest priority value allowed to pass
through the bridge port for any of this MEPs VIDs.
The management entity can obtain the default va…
Integer32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.8
zxAnPonOnuCfmMepEgressId
This attribute comprises 8 bytes to be included in LTMs.
They allow received LTRs to be directed to the correct originator.
The attribute includes the originator MAC address and a
locally-defined identifier. If this fie…
OctetStringr/w
Constraints:
range: 8-8
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.9
zxAnPonOnuCfmMepRmepIds
This attribute lists up to 12 expected peer MEPs for CCMs,
[IEEE 802.1ag] allows for multipoint networks, and therefore a list
of peer MEPs. This attribute allows for up to 12 peers for a
given MEP, though G-PON app…
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-64
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.10
zxAnPonOnuCfmMepAisEnable
This attribute enable generation of Ethernet AIS.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.11
zxAnPonOnuCfmMepAisPeriod
This attribute specifies ethernet AIS transmission period.
Enumerationr/w
Enumerated Values:
1time1s
2time1min
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.12
zxAnPonOnuCfmMepAisPriority
This attribute specifies priority of transmitted ETH AIS frames.
Integer32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.13
zxAnPonOnuCfmMepAisLevel
This attribute specifies the maintenance
level at which the client MEP exists.
Integer32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.14
zxAnPonOnuCfmMepAlarmThreshold
This attribute specifies the lowest priority alarm
that is allowed to generate a fault alarm.
mode1, All defects generate alarms after suitable soaking,
including AIS and RDICCM.
mode2, Alarm generated only by on…
Enumerationr/w
Enumerated Values:
1mode1
2mode2
3mode3
4mode4
5mode5
6mode6
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.15
zxAnPonOnuCfmMepAlarmDeSoakTime
This attribute defines the defect soak time
that must elapse before the MEP declares an alarm.
10msInteger32r/w
Constraints:
range: 250-1000
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.16
zxAnPonOnuCfmMepAlarmCSoakTime
This attribute defines the defect-free soak time
that must elapse before the MEP clears an alarm.
10msInteger32r/w
Constraints:
range: 250-1000
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.17
zxAnPonOnuCfmMepRowStatus
This attribute indicates the operation of the entry.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.3902.1082.500.3.2.8.4.1.50

zxAnPonRmOnuPppoeTestTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.9.2 · 1 row entry · 7 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuPppoeTestTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuPppoeTestTable' 
The table lists PPPoE test entry. the entry indicates the test.
zxAnPonRmOnuPppoeTestEntry row .1.3.6.1.4.1.3902.1082.500.3.2.9.2.1
An entry in the zxAnPonRmOnuPppoeTestTable.
Indexes
Column Syntax OID
zxAnPonRmPppoeTestVid
The VLAN of interface which will be used in testing datagram.

0 means that test will use the PVID of interface.
Non-zero value must be within the tagged VLAN list of interface. If
ONU can not find the VLA…
Integer32r/w
Constraints:
range: 0-4094
 .1.3.6.1.4.1.3902.1082.500.3.2.9.2.1.1
zxAnPonRmPppoeTestUsername
The user name.max size is 64 for epon, 25 for gpon
SNMPv2-TCDisplayStringr/w
Constraints:
range: 1-64
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.2.1.2
zxAnPonRmPppoeTestPassword
The password.max size is 32 for EPON, 25 for GPON
SNMPv2-TCDisplayStringr/w
Constraints:
range: 1-32
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.2.1.3
zxAnPonRmPppoeTestAuthMode
The protocol that is used to anthenticate user.
Enumerationr/w
Enumerated Values:
1auto
2chap
3pap
 .1.3.6.1.4.1.3902.1082.500.3.2.9.2.1.4
zxAnPonRmPppoeTestAction
The object is used to start or stop test.
start(1) - Start the test.
stop(2) - Stop the test.
Enumerationr/w
Enumerated Values:
1start
2stop
 .1.3.6.1.4.1.3902.1082.500.3.2.9.2.1.5
zxAnPonRmPppoeTestStatus
The status of test. Agent need keep this parameter updated so that
manager can get the latest status of test by polling.

notStarted(1) - test is not started
inProgress(2) - test is in progress
success(3) …
Enumeration
Enumerated Values:
1notStarted
2inProgress
3success
4failed
 .1.3.6.1.4.1.3902.1082.500.3.2.9.2.1.6
zxAnPonRmPppoeTestFailReason
The failed reason of test.

none(1) - no error
unknownError(2) - unknown error
hardwareNotSupport(3) - Hardware does not support the test.
notFindVlan(4) - Specified VLAN is not …
Enumeration
Enumerated Values:
1none
2unknownError
3hardwareNotSupport
4vlanNotExist
5padiTimeOut
6padrTimeOut
7lcpNegotiationFail
8userAuthFail
9ipNegotiationFail
 .1.3.6.1.4.1.3902.1082.500.3.2.9.2.1.7

zxAnPonRmOnuIpoeTestTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.9.3 · 1 row entry · 19 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuIpoeTestTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuIpoeTestTable' 
The table lists IPoE test entry. the entry indicates the test.
zxAnPonRmOnuIpoeTestEntry row .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1
An entry in the zxAnPonRmOnuIpoeTestTable.
Indexes
Column Syntax OID
zxAnPonRmIpoeTestAuthMode
IPoE test authentication mode.
option60String(1) - authenticate using
zxAnPonRmIpoeTestOption60String.
usernameAndPassword(2) - authenticate using
zxAnPonRmIpoeTes…
Enumerationr/w
Enumerated Values:
1option60String
2usernameAndPassword
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.1
zxAnPonRmIpoeTestUsername
The user name.
This object is valid when zxAnPonRmIpoeTestAuthMode is
usernameAndPassword(2).
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-64
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.2
zxAnPonRmIpoeTestPassword
The password. Max size is 16 for epon and gpon.
This object is valid when zxAnPonRmIpoeTestAuthMode is
usernameAndPassword(2).
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-16
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.3
zxAnPonRmIpoeTestClientMac
The IPoE test client MAC address.
SNMPv2-TCMacAddressr/w
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.4
zxAnPonRmIpoeTestOption60
The option60 for IPoE test.
This object is valid when zxAnPonRmIpoeTestAuthMode is
option60String(1).
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-128
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.5
zxAnPonRmIpoeTestVid
The VLAN id of interface which will be used in testing datagram.

0 means that test will use the PVID of interface.
Non-zero value must be within the tagged VLAN list of interface. If
ONU can not find the …
Integer32r/w
Constraints:
range: 0-4094
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.6
zxAnPonRmIpoeTestTimeout
The IPoE test timed out.
secondsInteger32r/w
Constraints:
range: 5-60
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.7
zxAnPonRmIpoeTestClientIpType
Client IP address type.
INET-ADDRESS-MIBInetAddressType
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.8
zxAnPonRmIpoeTestClientIpAddr
The IP address that is distributed by BAS when IPoE test is
completed successfully.
INET-ADDRESS-MIBInetAddress
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.9
zxAnPonRmIpoeTestGatewayIpType
The gateway IP address type.
INET-ADDRESS-MIBInetAddressType
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.10
zxAnPonRmIpoeTestGatewayIpAddr
The gateway IP address.
INET-ADDRESS-MIBInetAddress
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.11
zxAnPonRmIpoeTestPingTimes
The all times for IPoE test ping gateway.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.12
zxAnPonRmIpoeTestPingSucTimes
The successful times for IPoE test ping gateway.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.13
zxAnPonRmIpoeTestPingMaxDelay
The maximum delay for IPoE test ping gateway.
millisecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.14
zxAnPonRmIpoeTestPingMinDelay
The minimum delay for IPoE test ping gateway.
millisecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.15
zxAnPonRmIpoeTestPingAvgDelay
The average delay for IPoE test ping gateway .
millisecondsSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.16
zxAnPonRmIpoeTestAction
The object is used to start or stop test.

start(1) - Start the test.
stop(2) - Stop the test.
Enumerationr/w
Enumerated Values:
1start
2stop
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.17
zxAnPonRmIpoeTestStatus
The status of test. Agent need keep this parameter updated so that
manager can get the latest status of test by polling.

notStarted(1) - test is not started
inProgress(2) - test is in progress
success(3) …
Enumeration
Enumerated Values:
1notStarted
2inProgress
3success
4failed
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.18
zxAnPonRmIpoeTestFailReason
The failed reason of test.

none(1) - no error
ipoeDiscoverTimeOut(2) - IPoE discover timed out.
ipoeRequestTimeOut(3) - IPoE request timed out.
ipoeAuthFailed(4) - IPoE authentication…
Enumeration
Enumerated Values:
1none
2ipoeDiscoverTimeOut
3ipoeRequestTimeOut
4ipoeAuthFailed
5ipoeUnavailable
6ipoeTestTimeOut
7unknownError
8vlanNotExist
 .1.3.6.1.4.1.3902.1082.500.3.2.9.3.1.19

zxAnPonRmOnuVoipCalleeTestTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.9.5 · 1 row entry · 7 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuVoipCalleeTestTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuVoipCalleeTestTable' 
The table lists callee test entry. The entry indicates a test.
zxAnPonRmOnuVoipCalleeTestEntry row .1.3.6.1.4.1.3902.1082.500.3.2.9.5.1
An entry in the zxAnPonRmOnuVoipCalleeTestTable.
Indexes
Column Syntax OID
zxAnPonRmCalleeTestDuration
The duration of test. Agent should stop test following regular
on-hook procedure, if the test hasn't completed after duration yet.
secondsInteger32r/w
Constraints:
range: 60-300
 .1.3.6.1.4.1.3902.1082.500.3.2.9.5.1.1
zxAnPonRmCalleeTestMaxRingTime
The max ring time of test.
secondsInteger32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3902.1082.500.3.2.9.5.1.2
zxAnPonRmCalleeTestPortStatus
This object indicates the current status of port.

idle(1) - The state of port is idle.
ringing(2) - The state of port is ringing.
offHook(3) - The state of port is off-hook.
connected(4) - Voice data path…
Enumeration
Enumerated Values:
1idle
2ringing
3offHook
4connected
5busyTone
6onHook
 .1.3.6.1.4.1.3902.1082.500.3.2.9.5.1.3
zxAnPonRmCalleeTestAction
The object is used to start or stop test.
start(1) - Start the test.
stop(2) - Stop the test. Agent should stop test following regular
on-hook procedure.
Enumerationr/w
Enumerated Values:
1start
2stop
 .1.3.6.1.4.1.3902.1082.500.3.2.9.5.1.4
zxAnPonRmCalleeTestStatus
The status of test. Agent need keep this parameter updated so that
manager can get the latest status of test by polling.

notStarted(1) - Test is not started.
inProgress(2) - Test is in progress.
success(3…
Enumeration
Enumerated Values:
1notStarted
2inProgress
3success
4failed
 .1.3.6.1.4.1.3902.1082.500.3.2.9.5.1.5
zxAnPonRmCalleeTestFailReason
The failed reason of test.

other(1) - Other reason.
noRing(2) - No ringing.
noUpstreamVoice(3) - No upstream voice.
noDownstreamVoice(4) - No downstream voice.
noBidirectionVoice(5) - No upstream and down…
Enumeration
Enumerated Values:
1other
2noRing
3noUpstreamVoice
4noDownstreamVoice
5noBidirectionVoice
 .1.3.6.1.4.1.3902.1082.500.3.2.9.5.1.6
zxAnPonRmCalleeTestFailDetail
The failed detail. This field should be filled when the value of
zxAnPonRmCalleeTestFailReason is 'other'.
SNMPv2-TCDisplayString
Constraints:
range: 0-255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.5.1.7

zxAnPonRmOnuVoipCallerTestTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.9.6 · 1 row entry · 10 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuVoipCallerTestTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuVoipCallerTestTable' 
The table lists caller test entry. The entry indicates a test.
zxAnPonRmOnuVoipCallerTestEntry row .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1
An entry in the zxAnPonRmOnuVoipCallerTestTable.
Indexes
Column Syntax OID
zxAnPonRmCallerTestTimeout
The time-out of test. Agent should stop test following regular
on-hook procedure, if the test hasn't completed after time-out yet.
secondsInteger32r/w
Constraints:
range: 60-300
 .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1.1
zxAnPonRmCallerTestDialedNumber
The number that user dials.
The max size is 64 for EPON ,20 for GPON.
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-64
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1.2
zxAnPonRmCallerTestPortStatus
This object indicates the current status of port.

idle(1) - The state of port is idle.
offHook(2) - The state of port is off-hook.
dialTone(3) - The port is playing dial tone.
receiveNumber(4) - The port …
Enumeration
Enumerated Values:
1idle
2offHook
3dialTone
4receiveNumber
5receiveEnd
6ringBackTone
7connected
8busyTone
9onHook
 .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1.3
zxAnPonRmCallerTestDelay
Specifies how long it takes to set up bearer traffic RTP packets
for the POTS line being tested in tenths of a second.The delay
measure timer starts when the INVITE is generated for a call
origination to the phone numbe…
0.1secondInteger32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1.4
zxAnPonRmCallerTestSipFailReason
The failed reason of SIP test. This field should be filled when the
value of zxAnPonRmCallerTestFailReason is 'sipTestFailed'.

dialToneTestFailure(1) - Dial tone test failure.
inviteOkButNoBearerData(2) -…
Enumeration
Enumerated Values:
1dialToneTestFailure
2inviteOkButNoBearerData
3callTimeoutNo200Ok
4noResponseToInvite
5errorCodeAndReasonPhrase
6callCancelledByServer
7callCancelledByOnt
8lineNotConfigured
9lineNotInValidState
10lineNotRegistered
11notchFiltersRequired
 .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1.5
zxAnPonRmCallerTestSipErrorCode
The error code of SIP test. This field should be filled when the
value of zxAnPonRmCallerTestSipFailReason is
'errorCodeAndReasonPhrase'.

unauthorized(1) - 401 Unauthorized.
forbidden(2) - 403 Forbidden.
…
Enumeration
Enumerated Values:
1unauthorized
2forbidden
3notFound
4proxyAuthenticationRequired
5requestTimeout
6temporarilyUnavailable
7addressIncomplete
8busyHere
9requestTerminated
10notAcceptableHere
11serverInternalError
12serviceUnavailable
13serverTimeout
 .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1.6
zxAnPonRmCallerTestAction
The object is used to start or stop test.

start(1) - Start the test.
stop(2) - Stop the test. Agent should stop test following regular
on-hook procedure.
Enumerationr/w
Enumerated Values:
1start
2stop
 .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1.7
zxAnPonRmCallerTestStatus
The status of test. Agent need keep this parameter updated so that
manager can get the latest status of test by polling.

notStarted(1) - Test is not started.
inProgress(2) - Test is in progress.
success(3…
Enumeration
Enumerated Values:
1notStarted
2inProgress
3success
4failed
5notForced
 .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1.8
zxAnPonRmCallerTestFailReason
The failed reason of test.

other(1) - Other reason.
noDialTone(2) - No dial tone.
noRingBack(3) - No ring back tone.
noAnswer(4) - No answer.
noUpstreamVoice(5) - No upstream voice.
noDownstreamVoice(6) -…
Enumeration
Enumerated Values:
1other
2noDialTone
3noRingBack
4noAnswer
5noUpstreamVoice
6noDownstreamVoice
7noBidirectionVoice
8sipTestFailed
 .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1.9
zxAnPonRmCallerTestFailDetail
The failed detail. This field should be filled when the value of
zxAnOnuVoipCallerTestFailReason is 'other'.
SNMPv2-TCDisplayString
Constraints:
range: 0-255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.6.1.10

zxAnPonRmOnuOTransceiversTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.9.7 · 1 row entry · 9 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmOnuOTransceiversTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmOnuOTransceiversTable' 
ONU optical transceivers table.
zxAnPonRmOnuOTransceiversEntry row .1.3.6.1.4.1.3902.1082.500.3.2.9.7.1
ONU optical transceivers entry.
Indexes
Column Syntax OID
zxAnPonRmOnuOTSpeedMode
ONU optical transceivers speed mode.
The following values are valid for GPON:
gpon(1): GPON,
xgpon(2): XG-PON,
xgspon(3): XGS-PON,
unknown(255): unknown.
The following values are valid for EPON:
oneG…
Enumeration
Enumerated Values:
1gpon
2xgpon
3xgspon
11epon
12oneGAndTenGEpon
13tenGAnd10GEpon
255unknown
 .1.3.6.1.4.1.3902.1082.500.3.2.9.7.1.1
zxAnPonRmOnuOTOdnType
ONU optical transceivers ODN type.
The following values are valid for GPON:
classBplusAndCplus(1): Class B+/C+,
n1AndN2aAndE1AndE2a(2): N1/N2a/E1/E2a,
n2bAndE2b(3): N2b/E2b,
n1AndN2AndE1(4): N1/N2/E1.
Th…
Enumeration
Enumerated Values:
1classBplusAndCplus
2n1AndN2aAndE1AndE2a
3n2bAndE2b
4n1AndN2AndE1
51px20
52px20plus
53prx30
54pr30
55prx40
56pr40
255unknown
 .1.3.6.1.4.1.3902.1082.500.3.2.9.7.1.2
zxAnPonRmOnuOTApplicableDevType
ONU optical transceivers applicable device type.
Enumeration
Enumerated Values:
1onu
255unknown
 .1.3.6.1.4.1.3902.1082.500.3.2.9.7.1.3
zxAnPonRmOnuOTEncapsulationType
ONU optical transceivers encapsulation type.
sfpAndsfpplus(1): SFP/SFP+,
xfp(2): XFP,
unknown(255): unknown.
Enumeration
Enumerated Values:
1sfpAndsfpplus
2xfp
255unknown
 .1.3.6.1.4.1.3902.1082.500.3.2.9.7.1.4
zxAnPonRmOnuOTTxWavelength
ONU optical transceivers transmitted wavelength.
nmInteger32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3902.1082.500.3.2.9.7.1.5
zxAnPonRmOnuOTRxWavelength
ONU optical transceivers received wavelength.
nmInteger32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.3902.1082.500.3.2.9.7.1.6
zxAnPonRmOnuOTVendorName
ONU optical transceivers vendor name.
SNMPv2-TCDisplayString
Constraints:
range: 0-16
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.7.1.7
zxAnPonRmOnuOTVendorPn
ONU optical transceivers vendor part number.
SNMPv2-TCDisplayString
Constraints:
range: 0-16
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.7.1.8
zxAnPonRmOnuOTVendorSn
ONU optical transceivers vendor serial number.
SNMPv2-TCDisplayString
Constraints:
range: 0-16
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.9.7.1.9

zxAnPonRmXdsl2PMChannelH15MTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11 · 1 row entry · 9 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmXdsl2PMChannelH15MTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmXdsl2PMChannelH15MTable' 
The xDSL channel historical 15 minutes performance data table.
zxAnPonRmXdsl2PMChannelH15MEntry row .1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11.1
The xDSL channel historical 15 minutes performance data entry.this is not available
Indexes
Column Syntax OID
zxAnPonRmXdsl2ChH15MUnit
The termination unit, xtuc(1) or xtur(2).
VDSL2-LINE-TC-MIBXdsl2Unit
Type Values:
1xtuc
2xtur
 .1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11.1.1
zxAnPonRmXdsl2ChH15MChannelId
The channel ID of ONU xDSL port.
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11.1.2
zxAnPonRmXdsl2ChH15MInterval
The interval number.
Interval 1 is the the most recent previous interval and interval 96
is 24 hours ago. Intervals from 2 to 96 are optional.
Integer32
Constraints:
range: 1-96
 .1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11.1.3
zxAnPonRmXdsl2ChH15MCorrBlks
The total number of blocks received with errors that were
corrected on this channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11.1.4
zxAnPonRmXdsl2ChH15MUncorrBlks
The total number of blocks received with uncorrectable
errors on this channel during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11.1.5
zxAnPonRmXdsl2ChH15MTxBlks
The total number of blocks transmitted on this channel
during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11.1.6
zxAnPonRmXdsl2ChH15MRxBlks
The total number of blocks received on this channel
during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11.1.7
zxAnPonRmXdsl2ChH15MCodeViolates
The total number of coding violations on this channel
during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11.1.8
zxAnPonRmXdsl2ChH15MFecs
The total number of forward error corrections on this channel
during this interval.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.3902.1082.500.3.2.10.101.3.11.1.9

zxAnPonRmGfastLnConfTable

table
.1.3.6.1.4.1.3902.1082.500.3.2.11.3.5 · 1 row entry · 2 columns
Open in standard view
Uses the zte-ng variant from /opt/observium/mibs/zte-ng.
Command help
Walk zxAnPonRmGfastLnConfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZTE-AN-PON-REMOTE-ONU-MIB' -M '/opt/observium/mibs/zte-ng:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZTE-AN-PON-REMOTE-ONU-MIB::zxAnPonRmGfastLnConfTable' 
G.fast line configuration table. The index 'zxAnPonRmOnuUniIndex' 
of this table only supports xDSL UNI.
zxAnPonRmGfastLnConfEntry row .1.3.6.1.4.1.3902.1082.500.3.2.11.3.5.1
G.fast line configuration entry. The index 'zxAnPonOnuIndex'
represents the normal ONU index or the virtual ONU index
for profile.this is not available
Indexes
Column Syntax OID
zxAnPonRmGfastLnConfPrf
Refers to 'zxAnPonRmGfastLnConfPrfName'.
SNMPv2-TCDisplayStringr/w
Constraints:
range: 1-32
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.3902.1082.500.3.2.11.3.5.1.1
zxAnPonRmGfastLnConfRowStatus
The status of this conceptual row.
The state of this conceptual row only support
'not exist' and 'active'.
The action of this conceptual row only support
'createAndGo' and 'destroy'.

To create a row in t…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.3902.1082.500.3.2.11.3.5.1.50