TROPIC-SYNCE-MIB Table View

Table of Sync-E attributes.

tnSyncEEntry row .1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1

.

Indexes

TROPIC-SHELF-MIBtnShelfIndex TROPIC-SLOT-MIBtnSlotIndex

Column	Syntax	OID
tnSyncESyncMsg Determines if the timing reference selection for system timing uses Synchronization Status Message (SSM) Quality Levels or Enhanced Quality Levels.	TROPIC-TCNokiaSyncStatusMsgTyper/w Type Values: 1 true 2 false 3 enabledWithEnhancedQL	.1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.1
tnSyncEActiveRef The ID of the association line reference.	Enumeration Enumerated Values: 1 none 2 lineRef0 3 lineRef1 4 lineRef2 5 lineRef3 6 lineRef4 7 lineRef5	.1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.2
tnSyncEWTR The system timing WTR. Current configurable range: 0 to 12, and 999999.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.3
tnSyncESwCmdLineRef The third byte represents the switch command: 1 - nocmd 2 - clear 3 - lockout 4 - forceswitch 5 - mannual 6 - auto 7 - clearlockout. The last byte represents the line reference switch to: 0 - internal 1 -…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.4
tnSyncEClkModState The Sync-E clock mode state.	Enumeration Enumerated Values: 1 unknown 2 locked 3 autonomousHoldOver 4 autonomousFreeRunning 5 forcedFreeRunning	.1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.5
tnSyncESystemQL The value of the system quality level (SSM), shown in following: 31 - not applicable When the NE is in SDH mode: 0 - quality unknown 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - DNU 23 - …	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.6
tnSyncEQLDegradeThreshold The threshold value of SSM quality level degradation for systme timing reference. When the NE is in SDH mode: 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC - Default 23 - ePRTC 24 - PRTC 25 - ePRC…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.7
tnSyncECurrentActiveLineRefFreqOff The current frequency offset of the active timing reference.	ppbSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.8
tnSyncEAlmProfName .	OctetStringr/w Constraints: range: 1-40	.1.3.6.1.4.1.7483.2.2.4.8.2.1.1.1.9

Table of VTS map.

tnSyncELineRefEntry row .1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1

.

Indexes

TROPIC-SHELF-MIBtnShelfIndex TROPIC-SLOT-MIBtnSlotIndex tnSyncELineRefIndex

Column	Syntax	OID
tnSyncELineRefIndex The ifIndex of the line reference table.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.1
tnSyncELineRefAssignedPort The assigned port for the line reference.	Enumerationr/w Enumerated Values: 1 none 2 l1 3 l2 4 c1 5 c2 6 c3 7 c4 8 c5 9 c6 10 c7 11 c8 12 c9 13 c10 14 c11 15 c12 16 c13 17 c14 18 c15 19 c16 20 c17 21 c18 22 c19 23 c20 24 c21 25 c22 26 c23 27 c24 28 x1 29 x2 30 x3 31 x4 32 x5 33 x6 34 m1 35 m2 36 m3 37 m4 38 x7 39 x8 40 x9 41 x10 42 x11 43 x12	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.2
tnSyncELineRefPriority Line reference priority. Current configurable range: 0 to 8.	Unsigned32r/w Constraints: range: 0-8	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.3
tnSyncELineRefAdminState The administrative state of the line reference.	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.4
tnSyncELineRefOperState The operating state of the line reference.	Enumeration Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.5
tnSyncELineLockOut If lock out line reference or not.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.6
tnSyncELineRefState The Sync-E line reference state.	Enumeration Enumerated Values: 1 notAssigned 2 normal 3 signalFailure 4 wtr	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.7
tnSyncELineRefSwState The Sync-E line reference switch state.	Enumeration Enumerated Values: 1 nocmd 2 forced 3 mansw 4 lockout 5 wtr	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.8
tnSyncELineRefIncSSMMsg This object indicates the current value of incoming QL on that port. 30 - unstable 31 - not applicable When the NE works in SDH mode: 0 - Unknown 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.9
tnSyncELineRefIncSSMStatus This object indicates the current status of incoming QL on that port. 0: Valid 1: Invalid 2: Not Supported 3: Not Applicable It's applicable only to the timing port with SSM capabil…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.10
tnSyncELineRefIncSSMSupp Enable or disable the line reference incoming QL processing.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.11
tnSyncELineRefProvQL Manually provisioned incoming SSM value for the line reference. The value can be: 0 - AUTO When the NE is in SDH mode: 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - DNU 23 - e…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.12
tnSyncELineRefAssociatedPort The associated physical port of the line reference. This parameter replaces tnSyncELineRefAssignedPort in order to support assigning a line reference to a port in other slots.	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.13
tnSyncELineRefPriorityOfStationClock Line reference priority for the output station clock. Current configurable range: 0 to 8.	Unsigned32r/w Constraints: range: 0-8	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.14
tnSyncELineRefLockOutOfStationClock If lock out the line reference or not for the output station clock.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.15
tnSyncELineRefSwStateOfStationClock The Sync-E line reference switch state of the output station clock.	Enumeration Enumerated Values: 1 nocmd 2 forced 3 mansw 4 lockout 5 wtr	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.16
tnSyncELineRefCurrentFreqOff The current frequency offset of the timing reference.	ppbSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.17
tnSyncELineRefAlmProfName .	OctetStringr/w Constraints: range: 1-40	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.18
tnSyncELineRefIncExtdQLTLVClockID Incoming Extended QL TLV Clock ID.	TROPIC-PTP-MIBAluWdmPtpClockIdentifier Type Constraints: range: 8	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.19
tnSyncELineRefIncExtdQLTLVMixedClockType Incoming Extended QL TLV Mixed Clock Type Flag.	Enumeration Enumerated Values: 1 eEECFull 2 eEECMixedEEC	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.20
tnSyncELineRefIncExtdQLTLVPartialChain Incoming Extended QL TLV Partial Chain Flag.	Enumeration Enumerated Values: 1 completeChain 2 partialChain	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.21
tnSyncELineRefIncExtdQLTLVNumeEEC Incoming Extended QL TLV Number of eEEC.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.22
tnSyncELineRefIncExtdQLTLVNumEEC Incoming Extended QL TLV Number of EEC.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.23
tnSyncELineRefProvQLOfStationClock Manually provisioned incoming SSM value of the line reference output timing. The value can be: 0 - AUTO When the NE is in SDH mode: 1 - PRC 2 - SSU_A 3 - SSU_B 4 - SEC 5 - …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.24
tnSyncELineRefIncSSMMsgOfStationClock This object indicates the current value of incoming QL for output timing on that port. 30 - unstable 31 - not applicable When the NE works in SDH mode: 0 - Unknown 1 - PRC 2 - SSU_A 3 - SS…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.25
tnSyncELineRefIncSSMStatusOfStationClock This object indicates the current status of incoming QL on that port for output timing. 0: Valid 1: Invalid 2: Not Supported 3: Not Applicable It's applicable only to the timing por…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.2.1.26

Table of Sync-E Control attributes.

tnSyncEControlEntry row .1.3.6.1.4.1.7483.2.2.4.8.2.1.3.1

.

Indexes

TROPIC-SHELF-MIBtnShelfIndex TROPIC-SLOT-MIBtnSlotIndex

Column	Syntax	OID
tnSyncEControlEECEnable enable - The Synchronous Ethernet is supported for the pack and the synchronization attributes can be configured. disable - The Synchronous Ethernet is not supported for the pack and the synchronization attributes can …	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.2.4.8.2.1.3.1.1

Table of Sync-E Port attributes.

tnSyncEPortEntry row .1.3.6.1.4.1.7483.2.2.4.8.2.1.4.1

.

Indexes

IF-MIBifIndex

Column	Syntax	OID
tnSyncEOprMode The port Synchronous Ethernet Operation Mode. When the port is in SYNC mode, recovered clock of its input signal can be selected as a reference clock to the system clock. When the port is in NON-SYNC mode, the recover…	Enumerationr/w Enumerated Values: 1 sync 2 non-sync	.1.3.6.1.4.1.7483.2.2.4.8.2.1.4.1.1
tnSyncEOutgoingForceSsmTrans The port SSM/Quality Level Transmission value. The value can be: In SDH mode - act, prc, ssua, ssub, sec, dnu, ePRTC, PRTC, ePRC, eSEC, none; In sonet mode - act, stu, prs, st2, sts3e, st3, …	Enumerationr/w Enumerated Values: 1 act 2 prc 3 ssua 4 ssub 5 sec 6 dnu 7 stu 8 prs 9 st2 10 sts3e 11 st3 12 none 13 dus 23 ePRTC 24 pRTC 25 ePRC 26 eSEC	.1.3.6.1.4.1.7483.2.2.4.8.2.1.4.1.2

Table of Sync-E station clock attributes.

tnSyncEStationClockEntry row .1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1

.

Indexes

TROPIC-SHELF-MIBtnShelfIndex TROPIC-SLOT-MIBtnSlotIndex

Column	Syntax	OID
tnSyncEStationClockSyncMsg Determines if the timing reference selection for station clock timing uses Synchronization Status Message (SSM) Quality Levels or Enhanced Quality Levels.	TROPIC-TCNokiaSyncStatusMsgTyper/w Type Values: 1 true 2 false 3 enabledWithEnhancedQL	.1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.1
tnSyncEStationClockActiveRef The ID of the association line reference.	Enumeration Enumerated Values: 1 none 2 lineRef0 3 lineRef1 4 lineRef2 5 lineRef3 6 lineRef4 7 lineRef5	.1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.2
tnSyncEStationClockWTR The station clock timing WTR. Current configurable range: 0 to 12, and 999999.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.3
tnSyncEStationClockSwCmdLineRef The third byte represents the switch command: 1 - nocmd 2 - clear 3 - lockout 4 - forceswitch 5 - mannual 6 - auto 7 - clearlockout. The last byte represents the line reference switch to: 0 - internal 1 -…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.4
tnSyncEStationClockSystemQL The value of the system quality level (SSM) for the output timing clock, shown in following: 31 - not applicable When the NE is in SDH mode: 0 - quality unknown 1 - PRC 2 - SSU_A 3 - SSU_B …	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.5
tnSyncEStationClockQLThreshold Specifies the threshold value for the quality level i.e., SSM value for squelching the output towards timing output. If the quality value of the current selected signal for the output is below the threshold value, the …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.6
tnSyncEStationClockOutSel Specifies which signal is selected for the output station clock: OUTTIM - Output is selected from output timing selection process SETG - Output is selected from system internal timing The ID of the a…	Enumerationr/w Enumerated Values: 1 outtim 2 setg	.1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.7
tnSyncEStationClockAlmProfName .	OctetStringr/w Constraints: range: 1-40	.1.3.6.1.4.1.7483.2.2.4.8.2.1.5.1.8

Table of BITS port attributes.

tnSyncEBITSPortEntry row .1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1

.

Indexes

IF-MIBifIndex

Column	Syntax	OID
tnSyncEBITSPortDirection Indicate the direction of the BITS port.	Enumerationr/w Enumerated Values: 1 input 2 output	.1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.1
tnSyncEBITSPortSignalType Specify the signal type for the BITS interface: 0 - 2MHz 1 - unframed E1 2 - framed E1 without SSM 3 - framed E1 with SSM 4 - DS1 SF 5 - DS1 ESF. In SDH mode, 2MHz and E1 signal types are valid and 2MHz i…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.2
tnSyncEBITSPortSaBit Specifies the Sa bit location used to carry the SSM information. This parameter is only applicable when tnSyncEBITSPortSignalType = 3 (framed E1 with SSM)	Enumerationr/w Enumerated Values: 0 notApplicable 1 sa4 2 sa5 3 sa6 4 sa7 5 sa8	.1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.3
tnSyncEBITSPortOutputSSMTrans The port SSM/Quality Level Transmission value. The value can be: In SDH mode - act, prc, ssua, ssub, sec, dnu, none; In sonet mode - act, stu, prs, st2, sts3e, st3, dus, none. R…	Enumerationr/w Enumerated Values: 0 notApplicable 1 act 2 prc 3 ssua 4 ssub 5 sec 6 dnu 7 stu 8 prs 9 st2 10 sts3e 11 st3 12 none 13 dus	.1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.4
tnSyncEBITSPortOutputAISMode Specifies which signal is inserted for the timing output port if the output signal is squelched. The parameter is only applicable for output port types supporting SSM. AISMODE - AIS signal is inserted. QLMODE - DUS…	Enumerationr/w Enumerated Values: 0 notApplicable 1 aismode 2 qlmode	.1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.5
tnSyncEBITSPortLineImpedance Nominal line impedance. When in SDH mode, imp75ohms or imp120ohms could be used and the default is imp120ohms. When in ONET mode, imp100ohms could be used and the default is imp100ohms.	Enumerationr/w Enumerated Values: 1 imp75ohms 2 imp120ohms 3 imp100ohms	.1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.6
tnSyncEBITSPortLineCode Line code. This attribute is applicable when tnSyncEBITSPortSignalType is DS1 SF or DS1 ESF.	Enumerationr/w Enumerated Values: 1 b8zs 2 ami 3 notApplicable	.1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.7
tnSyncEBITSPortLbo Line equalization value for the BITS output port, taking one of the following values: - lbo: no compensation - lbo1: 0 to 133 feet - lbo2: 133 to 266 feet - lbo3: 267 to 399 feet - lbo4: 400 to 533 feet - lb…	Enumerationr/w Enumerated Values: 1 lbo 2 lbo1 3 lbo2 4 lbo3 5 lbo4 6 lbo5	.1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.8
tnSyncEBITSPortAlmProfName Alarm profile for BITs port	OctetStringr/w Constraints: range: 1-40	.1.3.6.1.4.1.7483.2.2.4.8.2.1.6.1.9

Table of Wan attributes.

tnWanEntry row .1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1

.

Indexes

IF-MIBifIndex

Column	Syntax	OID
tnWanAlmProfName .	OctetStringr/w	.1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.1
tnWanSyncEOprMode The Synchronous Ethernet Operation Mode. When in SYNC mode, recovered clock of its input signal can be selected as a reference clock to the system clock.When in NON-SYNC mode, the recovered clock of its input signal sh…	Enumerationr/w Enumerated Values: 1 sync 2 non-sync	.1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.2
tnWanSyncEOutgoingForceSsmTrans The port SSM/Quality Level Transmission value. The value can be: In SDH mode - act, prc, ssua, ssub, sec, dnu, ePRTC, PRTC, ePRC, eSEC, none. In SONET mode - act, prs, stu, st2, st3e, st3, …	Enumerationr/w Enumerated Values: 1 notApplicable 2 act 3 prc 4 ssua 5 ssub 6 sec 7 dnu 8 stu 9 prs 10 st2 11 sts3e 12 st3 13 none 14 dus 23 ePRTC 24 pRTC 25 ePRC 26 eSEC	.1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.3
tnWanAdminStatus Wan administrative state. It may be used to suppress the alarms or disable consequent actions on the WAN entity.	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.4
tnWanOperStatus operational state of WAN entity	Enumeration Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.5
tnWanStateQualifier Indicates the state qualifier (i.e., the secondary state) of the WAN state.	TROPIC-TCTropicStateQualifierType Type Values: 0 portRxFault 1 portTxFault 2 locked 3 ains 4 flt 5 mea 6 uas 7 ueq 8 abnormal 9 reserved9 10 mdlt 11 noimp 12 sdee 13 mt 14 sgeo 15 faf	.1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.6
tnWanOperationalCapability The partiallyEnabled(3) state means an abnormal state.	TROPIC-TCTropicOperationalCapabilityType Type Values: 1 disabled 2 enabled 3 partiallyEnabled	.1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.7
tnWanDescription Wan Description.	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.7483.2.2.4.8.2.1.7.1.8

Table of Sync-E Control attributes for a packetswitch.
This table provides the same functionality as
tnSyncEControlTable, but requires a switchid as an index

tnSyncEPacketswitchControlEntry row .1.3.6.1.4.1.7483.2.2.4.8.2.1.8.1

.

Indexes

TROPIC-SYSTEM-MIBtnSysSwitchId

Column	Syntax	OID
tnSyncEPacketswitchControlEECEnable enable - Synchronous Ethernet is supported for the packetswitch and the synchronization attributes can be configured. disable - Synchronous Ethernet is not supported for the packetswitch and the synchronization attribu…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7483.2.2.4.8.2.1.8.1.1