TIMETRA-LAG-MIB Table View

Configuration information about each Link Aggregation Group.

tLagConfigEntry row .1.3.6.1.4.1.6527.3.1.2.15.2.1

An entry (conceptual row) in the tLagConfigTable. Each entry
represents a Link Aggregation Group. Create or destroy rows to add or
remove Link Aggregation Groups (LAG).

After tLagRowStatus is set to active(…

Indexes

tLagIndex

Column	Syntax	OID
tLagIndex the number of the Link Aggregation Group.	TIMETRA-TC-MIBLAGInterfaceNumber Type Constraints: range: 1..800	.1.3.6.1.4.1.6527.3.1.2.15.2.1.1
tLagRowStatus RowStatus for this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6527.3.1.2.15.2.1.2
tLagPortThreshold tLagPortThreshold is a threshold for tLagPortThresholdAction. When a physical port link state changes and the number of operational physical ports is less than or equal to tLagPortThreshold, tLagPortThres…	Integer32r/w Constraints: range: 0-63	.1.3.6.1.4.1.6527.3.1.2.15.2.1.3
tLagPortThresholdAction Port Threshold Action is action to take when the number of operational (link up) physical ports is less than tLagPortThreshold. When a physical port ifOperStatus changes and the number of operational phys…	Enumerationr/w Enumerated Values: 1 down 2 dynamicCost 3 staticCost	.1.3.6.1.4.1.6527.3.1.2.15.2.1.4
tLagEnableMarkerGenerator enables (true(1)) or disables (false(2)) the Marker Generator protocol.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.5
tLagEnableLACP enables (true(1)) or disables (false(2)) the Link Aggregation Control Protocol (LACP). The value of tLagEnableLACP can only be set to 'true(1)' when tLagStandbySignaling is set to 'lacp(1)' and the value …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.6
tLagDescription Description text for the Link Aggregation Group port.	OctetStringr/w Constraints: range: 0-160	.1.3.6.1.4.1.6527.3.1.2.15.2.1.7
tLagDynamicCosting When dynamic cost and OSPF autocost are both configured then costing is applied based on the total number of links configured and the cost is advertised inversely proportional to the number of links available at the tim…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.8
tLagLACPMode tLagLACPMode represents the mode in which LACP will operate. If the value is set to 'passive', LACP places all member ports of a lag into a passive negotiating state. When this is the case member ports of the lag respon…	Enumerationr/w Enumerated Values: 1 passive 2 active	.1.3.6.1.4.1.6527.3.1.2.15.2.1.9
tLagLACPAdminKeyAutogen tLagLACPAdminKeyAutogen is set to 'true' if the lag administrative key in the dot3adAggActorAdminKey object was auto generated. tLagLACPAdminKeyAutogen is set to 'false', if the lag administrative key was manually confi…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.10
tLagLACPTransmitInterval tLagLACPTransmitInterval configures the timer interval for periodic transmission of LACP packets. If set to 'slow', LACP packets are transmitted every 30 seconds. If set to 'fast', LACP packets are transmitted every sec…	Enumerationr/w Enumerated Values: 1 slow 2 fast	.1.3.6.1.4.1.6527.3.1.2.15.2.1.11
tLagAccessAdaptQos The value of tLagAccessAdaptQos specifies how the LAG SAP queue and virtual scheduler buffering and rate parameters are adapted over multiple active MDAs. link (1) - The LAG will create the SAP queues and virt…	Enumerationr/w Enumerated Values: 1 link 2 distribute 3 portFair	.1.3.6.1.4.1.6527.3.1.2.15.2.1.12
tLagLACPXmitStdby The value of tLagLACPXmitStdby specifies whether or not LACP messages are transmitted on standby-links.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.13
tLagLACPSelCrit The value of tLagLACPSelCrit specifies which selection criteria should be used to select the active sub-group.	Enumerationr/w Enumerated Values: 1 highestCount 2 highestWeight 3 bestPort	.1.3.6.1.4.1.6527.3.1.2.15.2.1.14
tLagLACPSelCritSlaveToPartner The value of tLagLACPSelCritSlaveToPartner specifies together with tLagLACPSelCrit selection criteria should be used to select the active sub-group. The term 'eligible member' refers to a lag-member link which can pot…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.15
tLagLACPNbrOfSubGroups The value of tLagLACPNbrOfSubGroups indicates the number of subgroups configured in this LAG.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.2.1.16
tLagholdTimeDown The value of tLagholdTimeDown specifies the timer in 0.1 second units which controls the delay between detecting that a LAG is down (all active ports are down) and reporting it to the higher levels. The default value f…	decisecondsUnsigned32r/w Constraints: range: 0-2000	.1.3.6.1.4.1.6527.3.1.2.15.2.1.17
tLagPortType The value of tLagPortType specifies the type of ports allowed in this LAG. A value of 'standard (1)' allows all non-HSMDA and non-HS type ports to be added to this LAG. A value of 'hsmdaV2 (3)' limits th…	Enumerationr/w Enumerated Values: 1 standard 3 hsmdaV2 4 hs	.1.3.6.1.4.1.6527.3.1.2.15.2.1.18
tLagPerFpIngQueuing The value of tLagPerFpIngQueuing specifies whether a more efficient method of queue allocation for LAG SAPs should be utilized. An 'inconsistentValue' error is returned if this object is set to a differen…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.19
tLagSystemId The value of the object tLagSystemId specifies A 6-octet MAC address used as a unique identifier for the System that contains this Aggregator. If set to zero, the dot3adAggActorSystemID will be used as id…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.6527.3.1.2.15.2.1.20
tLagSystemPriority The value of the object tLagSystemPriority specifies a 2-octet value indicating the priority value associated with the Actor's System ID. If set to -1, the priority is taken from the object dot3adAggActor…	Integer32r/w Constraints: range: -1-65535	.1.3.6.1.4.1.6527.3.1.2.15.2.1.21
tLagStandbySignaling The value of tLagStandbySignaling specifies how the state of a member port is signalled to the remote side when the tLagPortActiveStdby corresponding to this member port has the value 'standby'. lacp …	Enumerationr/w Enumerated Values: 1 lacp 2 powerOff	.1.3.6.1.4.1.6527.3.1.2.15.2.1.22
tLagPerLinkHash The value of tLagPerLinkHash specifies whether SAP or interface associated with this LAG will send traffic over a single link of a LAG auto-rebalancing as links are added and removed from this LAG.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.23
tLagPerFpEgrQueuing The value of tLagPerFpEgrQueuing specifies whether a more efficient method of queue allocation for LAG SAPs should be utilized. An 'inconsistentValue' error is returned if this object is set to a differen…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.24
tLagIncludeEgrHashCfg The value of tLagIncludeEgrHashCfg specifies whether explicitly configured hashing should factor into the egress buffering and rate distribution (tLagAccessAdaptQos). When the value of tLagIncludeEgrHashC…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.25
tLagPerFpSapInstance The value of tLagPerFpSapInstance specifies whether a more efficient method of SAP allocation for LAG SAPs should be utilized. This object may only be set to true, if both tLagPerFpIngQueuing and tLagPerF…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.26
tLagLacpHoldTime The value of tLagLacpHoldTime specifies the time that this system waits before switching to a newly eligible sub-group while the currently active sub-group is active. In other words, if the system has swi…	decisecondsUnsigned32r/w Constraints: range: 4294967295-4294967295 range: 0-2000	.1.3.6.1.4.1.6527.3.1.2.15.2.1.27
tLagPerLinkHashWeighted The value of tLagPerLinkHashWeighted specifies whether there is a class and weight based balanced distribution of traffic egressing on the objects configured on the LAG. An 'inconsistentValue' error is re…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.29
tLagPerLinkHashWeightedRebalance The value of tLagPerLinkHashWeightedRebalance specifies whether to rebalance automatically when there is a class and weight based balanced distribution of traffic egressing on the objects configured on the LAG. …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.30
tLagPortWeightSpeed The value of tLagPortWeightSpeed specifies the speed corresponding to a weight unit. The value zero specifies that mixing ports with different speeds is not allowed in this LAG. For example…	gigabpsUnsigned32r/w Constraints: range: 10-10 range: 0-1	.1.3.6.1.4.1.6527.3.1.2.15.2.1.31
tLagWeightThreshold The value of the object tLagWeightThreshold specifies a threshold for the action specified by the object tLagWeightThresholdAction; the value is a weight, and the unit depends on the value of the object t…	Integer32r/w Constraints: range: 0-63	.1.3.6.1.4.1.6527.3.1.2.15.2.1.33
tLagWeightThresholdAction The value of the object tLagWeightThresholdAction specifies the action to take when the weight of the physical ports that are operational (link up) is less than the value of tLagWeightThreshold. When a ph…	Enumerationr/w Enumerated Values: 1 down 2 dynamicCost 3 staticCost	.1.3.6.1.4.1.6527.3.1.2.15.2.1.34
tLagMonitorOperGrpName The value of tLagMonitorOperGrpName specifies the operational group of which the status affects the status of this LAG. If the value is not empty, it must correspond to a conceptual row in the TIMETRA-SER…	TIMETRA-TC-MIBTNamedItemOrEmptyr/w Type Constraints: range: 0..32	.1.3.6.1.4.1.6527.3.1.2.15.2.1.36
tLagLacpMuxControl The value of tLagLacpMuxControl specifies the LACP MUX (multiplexer) state machine variant. The value 'coupled' specifies that transmit and receive directions are activated together, while the value 'inde…	Enumerationr/w Enumerated Values: 1 coupled 2 independent	.1.3.6.1.4.1.6527.3.1.2.15.2.1.37
tLagBfdDisableSoftResetExt The value of tLagBfdDisableSoftResetExt specifies if the extension of Bidirectional Forwarding Detection (BFD) timers during soft reset is disabled. While the value of tLagBfdDisableSoftResetExt is 'true'…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.38
tLagAccessBandwidth The value of tLagAccessBandwidth specifies the administrative bandwidth assigned to this lag. The administrative bandwidth can be over or under booked using the value of tLagAccessBookingFactor.	kilobpsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.2.1.39
tLagAccessBookingFactor The value of tLagAccessBookingFactor specifies the booking factor, against the administrative bandwidth specified by tLagAccessBandwidth.	Unsigned32r/w Constraints: range: 1-1000	.1.3.6.1.4.1.6527.3.1.2.15.2.1.40
tLagAccessAvailableBW The value of tLagAccessAvailableBW indicates the bandwidth that is still free for booking on this lag.	kilobpsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.6527.3.1.2.15.2.1.41
tLagAccessBookedBW The value of tLagAccessBookedBW indicates the lag bandwidth that has been booked.	kilobpsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.6527.3.1.2.15.2.1.42
tLagPortThresholdStaticCost The value of the object tLagPortThresholdStaticCost specifies the cost of the LAG link when the number of operational (link up) physical ports is less than tLagPortThreshold, and the value of the object tLagPortThreshol…	Unsigned32r/w Constraints: range: 0-16777215	.1.3.6.1.4.1.6527.3.1.2.15.2.1.43
tLagWeightThresholdStaticCost The value of the object tLagWeightThresholdStaticCost specifies the cost of the LAG link when the weight of operational (link up) physical ports is less than tLagWeightThreshold, and the value of the object tLagWeightTh…	Unsigned32r/w Constraints: range: 0-16777215	.1.3.6.1.4.1.6527.3.1.2.15.2.1.44
tLagAccessBandwidthHigh The value of tLagAccessBandwidthHigh specifies the higher 32 bits of the bandwidth assigned to this lag. The object tLagAccessBandwidth specifies the lower 32 bits. The administrative bandw…	kilobpsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.2.1.45
tLagHashWeightThreshold The value of the object tLagHashWeightThreshold specifies a threshold for the action specified by the object tLagHashWeightThresholdAction; The value of tLagHashWeightThreshold is compared to the sum of t…	Integer32r/w Constraints: range: 0-6400000	.1.3.6.1.4.1.6527.3.1.2.15.2.1.46
tLagHashWeightThresholdAction The value of the object tLagHashWeightThresholdAction specifies the action to take when the weight of the physical ports that are operational (link up) is less than the value of tLagHashWeightThreshold. W…	Enumerationr/w Enumerated Values: 1 down 2 dynamicCost 3 staticCost	.1.3.6.1.4.1.6527.3.1.2.15.2.1.47
tLagHashWeightThresholdStaticCst The value of the object tLagHashWeightThresholdStaticCst specifies the cost of the LAG link when the weight of operational (link up) physical ports is less than tLagHashWeightThreshold, and the value of the object tLagH…	Unsigned32r/w Constraints: range: 0-16777215	.1.3.6.1.4.1.6527.3.1.2.15.2.1.48
tLagAdaptiveLb The value of the object tLagAdaptiveLb specifies if the system applies adaptive load balancing to the member ports of this LAG.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.2.1.49
tLagAdaptiveLbTolerance The value of tLagAdaptiveLbTolerance specifies the allowed difference between the highest member port load and the lowest. The value is only relevant while tLagAdaptiveLb is equal to 'true'.	percentUnsigned32r/w Constraints: range: 1-100	.1.3.6.1.4.1.6527.3.1.2.15.2.1.50

Operational information about each Link Aggregation Group.

tLagOperationEntry row .1.3.6.1.4.1.6527.3.1.2.15.3.1

An entry (conceptual row) in the tLagOperationTable. Each entry
represents an active Link Aggregation Group.

Indexes

No indexes recorded

Column	Syntax	OID
tLagIfIndex ifIndex for the Link Aggregation Group. This value is zero when tLagRowStatus is not active(1).	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.6527.3.1.2.15.3.1.1
tLagConfigLastChange last change timestamp records when any object in tLagConfigTable was set.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.6527.3.1.2.15.3.1.2
tLagPortThresholdFalling counts the number of linkDown or dynamicCost events for the Link Aggregation Group caused by the number of physical ports being less than or equal to tLagPortThreshold value.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.3.1.3
tLagPortThresholdRising counts the number of linkUp or dynamicCost events for the Link Aggregation Group caused by the number of physical ports being greater than tLagPortThreshold value.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.3.1.4
tLagLACPPrimaryPortobsolete tLagLACPPrimaryPort contains the primary port of the LACP. The following two conditions have to be met for the port to become eligible for becoming the primary port: a) Port has to be in either link up or oper up. b) Th…	TIMETRA-TC-MIBTmnxPortID	.1.3.6.1.4.1.6527.3.1.2.15.3.1.5
tLagPortReasonDownFlagsobsolete The tLagPortReasonDownFlags indicates why a lag port may be in the operationally 'down' state. The following reasons are detected through this object: unknown(0) - Unspecified (or unknown) linklossFwd(…	Bits Enumerated Values: 0 unknown 1 linklossFwd	.1.3.6.1.4.1.6527.3.1.2.15.3.1.6
tLagSelectedSubGroup The value of tLagSelectedSubGroup indicates the currently selected sub-group. The value zero indicates that the value is not applicable. The value minus one can appear in a multi-chassis LA…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6527.3.1.2.15.3.1.7
tLagCandidateSubGroup The value of tLagCandidateSubGroup indicates the candidate sub-group. The value zero indicates that the value is not applicable. The value minus one can appear in a multi-chassis LAG config…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6527.3.1.2.15.3.1.8
tLagRemainingHoldTime The value of tLagRemainingHoldTime indicates the time remaining before this system would switch to the newly eligible sub-group. The value zero indicates that the system would immediately switch back. …	decisecondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.3.1.9
tLagPortWeightUp The value of tLagPortWeightUp indicates the weight of the physical ports that are operational (link up). The weight of each LAG member port is either configured or derived from the port speed. …	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.3.1.10
tLagAdaptiveLbVariation The value of tLagAdaptiveLbVariation indicates the actual difference between the highest member port load and the lowest. The value is only relevant while tLagAdaptiveLb is equal to 'true'.	percentUnsigned32 Constraints: range: 0-100	.1.3.6.1.4.1.6527.3.1.2.15.3.1.11
tLagAdaptiveLbChanged The value of tLagAdaptiveLbChanged indicates the number of times a load balancing change event tLagAdaptiveLoadbalancingChanged occurred for this LAG.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.3.1.12

The tLagMemberTable has an entry for each Port that is part of a LAG.

tLagMemberEntry row .1.3.6.1.4.1.6527.3.1.2.15.5.1

Each row entry represents a particular port in a LAG. Entries are
automatically created when a Port is provisioned as part of a LAG,
i.e. when tmnxPortLagId from TIMETRA-PORT-MIB.mib is changed from its
default value of…

Indexes

tLagIndex TIMETRA-PORT-MIBtmnxPortPortID

Column	Syntax	OID
tLagMemberPortName The value of tLagMemberPortName indicates the name of the port that is a member of the LAG used to index into tLagMemberTable. This is a read-only object that is the same as tmnxPortName from TIMETRA-PORT-MIB.mib.	TIMETRA-TC-MIBTNamedItemOrEmpty Type Constraints: range: 0..32	.1.3.6.1.4.1.6527.3.1.2.15.5.1.1
tLagMemberPortIsPrimary The value of tLagMemberPortIsPrimary indicates whether the port used to index into tLagMemberTable is the primary port of the LAG used to index into tLagMemberTable.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.5.1.2

The tLagPortTable extends the IEEE8023-LAG-MIB::dot3adAggPortTable
with 7x50 specific features.

tLagPortEntry row .1.3.6.1.4.1.6527.3.1.2.15.6.1

A list of Link Aggregation Control configuration parameters for each
Aggregation Port on this device. The tLagPortTable extends the
IEEE8023-LAG-MIB::dot3adAggPortTable with 7x50 specific features.

Indexes

No indexes recorded

Column	Syntax	OID
tLagPortSubgroup The value of tLagPortSubgroup specifies the subgroup to which the port in this LAG is assigned.	LAGSubgroupr/w Type Constraints: range: -2..-1 range: 1..8	.1.3.6.1.4.1.6527.3.1.2.15.6.1.1
tLagPortActiveStdby The value of tLagPortActiveStdby indicates active standby state of this port in the LAG.	Enumeration Enumerated Values: 1 active 2 stand-by	.1.3.6.1.4.1.6527.3.1.2.15.6.1.2
tLagPortHashWeight The value of tLagPortHashWeight specifies the hash weight of this port within the LAG. A value of zero means there is no weight configured, while a value of minus one means the weight is derived from the …	Integer32r/w Constraints: range: -1-100000	.1.3.6.1.4.1.6527.3.1.2.15.6.1.3
tLagPortOperHashWeight The value of tLagPortOperHashWeight indicates the operational hash weight of this port within the LAG.	Integer32 Constraints: range: 1-100000	.1.3.6.1.4.1.6527.3.1.2.15.6.1.4
tLagPortFlowShare The value of tLagPortFlowShare indicates the ratio of the number of traffic flows pre-assigned to this port and the sum of the number of flows pre-assigned to each operational port of the LAG. The value …	centipercentUnsigned32 Constraints: range: 0-10000	.1.3.6.1.4.1.6527.3.1.2.15.6.1.5
tLagPortAdaptiveLbEgressRate The value of tLagPortAdaptiveLbEgressRate indicates the egress traffic rate on this LAG port when adaptive load balancing is enabled on the LAG. When adaptive load balancing is disabled on the LAG, the va…	kilobpsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.6527.3.1.2.15.6.1.6

The tLagLinkMapProfileTable has an entry for each LAG link map
profile.

tLagLinkMapProfileEntry row .1.3.6.1.4.1.6527.3.1.2.15.8.1

The tLagLinkMapProfileEntry contains the information about a
particular LAG link map profile.

Indexes

tLagIndex tLagLinkMapProfileId

Column	Syntax	OID
tLagLinkMapProfileId The value of tLagLinkMapProfileId specifies a LAG link map profile identifier.	TIMETRA-TC-MIBTmnxLinkMapProfileId Type Constraints: range: 1..64	.1.3.6.1.4.1.6527.3.1.2.15.8.1.1
tLagLinkMapProfileRowStatus This value of the object tLagLinkMapProfileRowStatus specifies the status of this row. Entries are created and deleted using this object.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6527.3.1.2.15.8.1.2
tLagLinkMapProfileLastChanged The value of tLagLinkMapProfileLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local ne…	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.6527.3.1.2.15.8.1.3
tLagLinkMapProfileDescription The value of tLagLinkMapProfileDescription specifies the user provided description of this entry.	TIMETRA-TC-MIBTItemDescriptionr/w Type Constraints: range: 0..80	.1.3.6.1.4.1.6527.3.1.2.15.8.1.4
tLagLinkMapProfileFailureMode The value of tLagLinkMapProfileFailureMode specifies the failure mode operation of this entry. When the value of tLagLinkMapProfileFailureMode is set to 'down', SAP or interface associated with this LAG w…	Enumerationr/w Enumerated Values: 1 perLinkHash 2 discard	.1.3.6.1.4.1.6527.3.1.2.15.8.1.5
tLagLinkMapProfileActiveLink The value of tLagLinkMapProfileActiveLink indicates the active link port for this entry.	TIMETRA-TC-MIBTmnxPortID	.1.3.6.1.4.1.6527.3.1.2.15.8.1.6

The tLagLinkMapProfPortTable has an entry for each associated port of
lag link map profile.

tLagLinkMapProfPortEntry row .1.3.6.1.4.1.6527.3.1.2.15.10.1

The tLagLinkMapProfPortEntry contains the information about a
particular port associated with the LAG link map profile.

Indexes

tLagIndex tLagLinkMapProfileId tLagLinkMapProfPortId

Column	Syntax	OID
tLagLinkMapProfPortId The value of tLagLinkMapProfPortId specifies an associated port to the LAG link map profile.	TIMETRA-TC-MIBTmnxPortID	.1.3.6.1.4.1.6527.3.1.2.15.10.1.1
tLagLinkMapProfPortRowStatus This value of the object tLagLinkMapProfPortRowStatus specifies the status of this row. Entries are created and deleted using this object.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.6527.3.1.2.15.10.1.2
tLagLinkMapProfPortLastChanged The value of tLagLinkMapProfPortLastChanged indicates the sysUpTime at the time of the last modification of this entry. If no changes were made to the entry since the last re-initialization of the local n…	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.6527.3.1.2.15.10.1.3
tLagLinkMapProfPortType The value of tLagLinkMapProfPortType specifies the type of the associated port for this entry. The value of this object must be specified at the time of creation of the entry.	Enumerationr/w Enumerated Values: 1 primary 2 secondary	.1.3.6.1.4.1.6527.3.1.2.15.10.1.4

The tLagPerLinkHashWtPortClassTable maintains the number of users and
aggregate weight per class per port for weighted per-link-hash enabled
LAGs.

tLagPerLinkHashWtPortClassEntry row .1.3.6.1.4.1.6527.3.1.2.15.11.1

The tLagPerLinkHashWtPortClassEntry contains the information about a
particular class on a specific active port of the lag.

Indexes

tLagIndex tLagPerLinkHashWtPort tLagPerLinkHashWtPortClassId

Column	Syntax	OID
tLagPerLinkHashWtPort The value of tLagPerLinkHashWtPort indicates the port of the lag with tLagPerLinkHashWeighted enabled.	TIMETRA-TC-MIBTmnxPortID	.1.3.6.1.4.1.6527.3.1.2.15.11.1.1
tLagPerLinkHashWtPortClassId The value of tLagPerLinkHashWtPortClassId indicates the traffic class for the port of the LAG.	TIMETRA-TC-MIBTmnxLagPerLinkHashClass Type Constraints: range: 1..3	.1.3.6.1.4.1.6527.3.1.2.15.11.1.2
tLagPerLinkHashWtPortClassUsers The value of tLagPerLinkHashWtPortClassUsers indicates number of users on the class for the port of the LAG.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6527.3.1.2.15.11.1.3
tLagPerLinkHashWtPortClassAggWt This value of tLagPerLinkHashWtPortClassAggWt indicates aggregate weight of all users on the class for the port of the LAG.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.6527.3.1.2.15.11.1.4

The tmnxLagActionTable allows actions on the Certificate-Authority
profiles.

tmnxLagActionEntry row .1.3.6.1.4.1.6527.3.1.2.15.12.1

The tmnxLagActionEntry allows action on a specific
Certificate-Authority profile.

Indexes

tLagIndex

Column	Syntax	OID
tmnxLagActionType The tmnxLagActionType specifies the action to be performed on the CA profile. The tmnxLagActionType and tmnxLagAction objects must be set together for the specific action to be performed.	Enumerationr/w Enumerated Values: 0 none 1 loadBalance	.1.3.6.1.4.1.6527.3.1.2.15.12.1.1
tmnxLagAction The value of tmnxLagAction specifies to perform action specified in the tmnxLagActionType object. The value of tmnxLagAction will always be returned as 'notApplicable'. The tmnxLagActionTyp…	TIMETRA-TC-MIBTmnxActionTyper/w Type Values: 1 doAction 2 notApplicable	.1.3.6.1.4.1.6527.3.1.2.15.12.1.2
tmnxLagActionClassId The tmnxLagActionClassId specifies the per-link-hash class identifier associated with requested action on the LAG.	TIMETRA-TC-MIBTmnxLagPerLinkHashClassOrNoner/w Type Constraints: range: 0..3	.1.3.6.1.4.1.6527.3.1.2.15.12.1.3

The tLagPortStatsLacpTable contains detailed statistics for LAG ports.

tLagPortStatsLacpEntry row .1.3.6.1.4.1.6527.3.1.2.15.13.1

A list of Link Aggregation Control statistics counters for each
Aggregation Port on this device. The tLagPortTable extends the
IEEE8023-LAG-MIB::dot3adAggPortTable with 7x50 specific features.

Indexes

No indexes recorded

Column	Syntax	OID
tLagPortStatsLacpTx The value of tLagPortStatsLacpTx indicates the number of valid LACP PDUs transmitted on this port	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.13.1.1
tLagPortStatsLacpRx The value of tLagPortStatsLacpRx indicates the number of valid LACP PDUs received on this port	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.13.1.2
tLagPortStatsLacpRxErrors The value of tLagPortStatsLacpRxErrors indicates the number of invalid LACP PDUs received on this port	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.13.1.3
tLagPortStatsLacpRxIllegal The value of tLagPortStatsLacpRxIllegal indicates the number of illegal LACP PDUs received on this port	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.13.1.4

The tmnxLagBfdFamTable allows the configuration of LAG per-member
Bidirectional Forwarding Detection (BFD) for the IPv4 and IPv6 micro
BFD sessions.

tmnxLagBfdFamEntry row .1.3.6.1.4.1.6527.3.1.2.15.50.2.1

Each conceptual row represents information for a particular LAG's
micro BFD sessions of a particular IP address family (IPv4 or IPv6).

Conceptual rows in this table are created and destroyed automatically
b…

Indexes

tLagIndex tmnxLagBfdFamAddressType

Column	Syntax	OID
tmnxLagBfdFamAddressType The value of tmnxLagBfdFamAddressType specifies the IP address type of this micro BFD session configuration.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.1
tmnxLagBfdFamLastCh The value of tmnxLagBfdFamLastCh indicates the sysUpTime at the time of the most recent management-initiated change to this table row.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.2
tmnxLagBfdFamAdminState The value of tmnxLagBfdFamAdminState specifies the administrative state of BFD for this IP address family on this LAG.	TIMETRA-TC-MIBTmnxEnabledDisabledr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.3
tmnxLagBfdFamAddrType The value of tmnxLagBfdFamAddrType specifies the address type of tmnxLagBfdFamAddr. Any value other than 'unknown' must be equal to the value of tmnxLagBfdFamAddressType.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.4
tmnxLagBfdFamAddr The value of tmnxLagBfdFamAddr specifies the local IP address.	OctetStringr/w Constraints: range: 16-16 range: 4-4 range: 0-0	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.5
tmnxLagBfdFamRemAddrType The value of tmnxLagBfdFamRemAddrType specifies the address type of tmnxLagBfdFamRemAddr. Any value other than 'unknown' must be equal to the value of tmnxLagBfdFamAddressType.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.6
tmnxLagBfdFamRemAddr The value of tmnxLagBfdFamRemAddr specifies the remote IP address.	OctetStringr/w Constraints: range: 16-16 range: 4-4 range: 0-0	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.7
tmnxLagBfdFamTransmitInterval The value of tmnxLagBfdFamTransmitInterval specifies the transmit timer for the BFD packets.	millisecondsUnsigned32r/w Constraints: range: 10-100000	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.8
tmnxLagBfdFamReceiveInterval The value of tmnxLagBfdFamReceiveInterval specifies the receive timers for the BFD packets.	millisecondsUnsigned32r/w Constraints: range: 10-100000	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.9
tmnxLagBfdFamMultiplier The value of tmnxLagBfdFamMultiplier specifies the number of consecutive BFD messages that must be missed from the peer before the BFD session state is changed to down.	Unsigned32r/w Constraints: range: 3-20	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.10
tmnxLagBfdFamMaxSetupTime The value of tmnxLagBfdFamMaxSetupTime specifies the maximum time the system will behave as if the micro-BFD session were 'Up', regardless of the actual state of the micro-BFD session being established. W…	millisecondsInteger32r/w Constraints: range: -1-60000	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.11
tmnxLagBfdFamMaxAdminDownTime The value of tmnxLagBfdFamMaxAdminDownTime specifies the maximum time the system will continue to behave as if the micro-BFD session was 'Up', after the remote system has signalled it as administratively down by means o…	secondsInteger32r/w Constraints: range: -1-3600	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.12
tmnxLagBfdFamBfdOnDistributing The value of tmnxLagBfdFamBfdOnDistributing specifies if BFD is started only on links in LACP 'distributing' state. While the value of tmnxLagBfdFamBfdOnDistributing is equal to 'true', BFD is started onl…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.6527.3.1.2.15.50.2.1.13

The tmnxLagBfdMemTable extends the tLagMemberTable with BFD specific
features.
          
Conceptual rows are automatically created when a port is provisioned
as part of a LAG.

tmnxLagBfdMemEntry row .1.3.6.1.4.1.6527.3.1.2.15.50.3.1

Each row entry represents BFD-specific information about a particular
port in a LAG.

Indexes

No indexes recorded

Column	Syntax	OID
tmnxLagBfdMemState The value of tmnxLagBfdMemState indicates the state of the micro-BFD session of this port in this LAG. Possible states are: idle : there is no BFD session; failed : the creation of the BFD ses…	Enumeration Enumerated Values: 0 idle 1 failed 2 failedFwd 3 waiting 4 waitingFwd 5 up 6 down	.1.3.6.1.4.1.6527.3.1.2.15.50.3.1.1
tmnxLagBfdMemSetupTimeLeft The value of tmnxLagBfdMemSetupTimeLeft indicates the setup time left. The value zero indicates that the setup timer is not running. Refer to the description of the object tmnxLagBfdFamMaxS…	millisecondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.50.3.1.2
tmnxLagBfdMemAdminDownLeft The value of tmnxLagBfdMemAdminDownLeft indicates the time left before this system will react upon the 'AdminDown' State indication. The value zero indicates that the timer is not running. …	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.6527.3.1.2.15.50.3.1.3