SUPERMICRO-MI-BGP-MIB Table View

This context table contains the global parameters of BGP 
that is required to be configured for each context.

fsMIBgpContextEntry row .1.3.6.1.4.1.10876.101.2.77.14.1

An Entry for the configuration in a particular VR.

Indexes

fsMIBgp4ContextId

Column	Syntax	OID
fsMIBgp4ContextId The index value that uniquely identifies the virtual router in which the configuration is done.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.2.77.14.1.1
fsMIBgp4GlobalAdminStatus The desired state of the BGP system. The BGP4 speaker is functionally active only when the global admin status is up. The global admin status can be made up only if the fsMIBgp4LocalAs is configured.	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.10876.101.2.77.14.1.2
fsMIBgp4Identifier This object configures the BGP Identifier in that VR. If admin status is made up, by default the BGP Identifier will take the value of highest interface address. If the BGP Speaker is administratively active, then the …	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.2.77.14.1.3
fsMIBgp4Synchronization Attribute to enable/disable synchronization within an AS. This object can be set only if fsMIBgp4LocalAs has been configured.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.14.1.4
fsMIBgp4DefaultLocalPref The default value of local-pref that is to be sent in updates to internal peers.This object can be set only if fsMIBgp4LocalAs has been configured.	Unsigned32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.10876.101.2.77.14.1.5
fsMIBgp4AdvtNonBgpRt This mib object can be used to configure the peer type to whom non-bgp routes can be propagated. external - indicates non-bgp routes can be exported to only external peers.All type…	Enumerationr/w Enumerated Values: 1 external 2 externalAndinternal	.1.3.6.1.4.1.10876.101.2.77.14.1.6
fsMIBgp4TraceEnable This object can be used to enable trace dynamically in BGP module. A four byte integer value is specified for enabling the level of tracing.Each Bit in the four byte integer variable represents a level of Trace. The bit…	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.14.1.7
fsMIBgp4DebugEnable This object can be used to enable debug dynamically in BGP module. Its a four byte integer value specified for enabling the level of debugging. Each Bit in the four byte integer variable represents a level of debug. The…	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.14.1.8
fsMIBgp4OverlappingRoute This object is used to configure the BGP speaker's policy for handling the overlapping routes. When an overlapping route is received, depending upon the configured policy either the less-specific routes or more-specific…	Enumerationr/w Enumerated Values: 1 moreSpecific 2 lessSpecific 3 both	.1.3.6.1.4.1.10876.101.2.77.14.1.9
fsMIBgp4AlwaysCompareMED If this object is set to disable, then in best route decision process, MED will be compared only between routes received from the same autonomous system. If set to enable, irrespective of the autonomous system from whic…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.14.1.10
fsMIBgp4DefaultOriginate If this object is set to enable/disable the redistribution and advertisement of the default route (0.0.0.0/0). By default, the default routes are not redistributed into BGP. Only if this object is set as enable, the def…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.14.1.11
fsMIBgp4DefaultIpv4UniCast If this object is set to enable, and if a neighbor is created, then the MP IPv4 Unicast Address Family Capability will be negotiate for that peer. If this object is set as disable and if a neighbor is created, then IPv4…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.14.1.12
fsMIBgp4IsTrapEnabled If this object is set to disable, then the NOTIFICATION messages wont be sent to the SNMP Manager. If enabled, NOTIFICATION messages are sent.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.14.1.13
fsMIBgp4NextHopProcessingInterval This object is used to configure the interval at which next hops will be mointored for reachablity	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.2.77.14.1.14
fsMIBgp4IBGPRedistributionStatus If this object is set to enable, IBGP routes will also be redistributed to other IGP protocols when redistribution is enabled for that protocol	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.14.1.15
fsMIBgp4RRDAdminStatus Controls redistribution of Direct, Static, IGP(OSPF,RIP) routes into BGP. If this object is set to enable, then routes from protocols as specified by fsMIBgp4RRDProtoMaskForEnable will be imported into BGP and the BGP l…	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.10876.101.2.77.14.1.16
fsMIBgp4RRDProtoMaskForEnable The bit mask of source protocols from which routes are imported to BGP.(LSB corresponds to Bit 0) Bit 1, if set, indicates that direct routes can be redistributed into BGP. (value = 2) …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.2.77.14.1.17
fsMIBgp4RRDSrcProtoMaskForDisable The bit mask of source protocols from which redistribution to BGP is disabled.(LSB corresponds to Bit 0) Bit 1, if set, indicates that direct routes cannot be redistributed into BGP. (value = 2)…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.2.77.14.1.18
fsMIBgp4RRDDefaultMetric The default metric value for the IGP routes and static route. If configured to 0, the metric received from the IGP route will be used. If configured to other value, the MED value of the redistributed routes take this va…	Unsigned32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.10876.101.2.77.14.1.19
fsMIBgp4RRDRouteMapName Name Identifies the specified route-map in the list of route-maps. If this Object needs to be changed, first reset this object and then configure the new value.	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.10876.101.2.77.14.1.20
fsMIBgp4RRDMatchTypeEnable Match type Enable specifies the OSPF route type that needs to be redistributed into BGP, This object is used only ospf redistribution.	Enumerationr/w Enumerated Values: 1 external 2 internal 4 nssaExternal	.1.3.6.1.4.1.10876.101.2.77.14.1.21
fsMIBgp4RRDMatchTypeDisable Match type Disable specifies the OSPF route type that should be disbled from redistribution into BGP. This object is used only for OSPF protocol.	Enumerationr/w Enumerated Values: 1 external 2 internal 4 nssaExternal	.1.3.6.1.4.1.10876.101.2.77.14.1.22
fsMIBgp4AscConfedId The Local Confederation Identification number of the AS confederation, a value of zero indicates the absence of this value. The object fsbgp4LocalAs must be configured prior to configuring this object. If already set (t…	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.14.1.23
fsMIBgp4AscConfedBestPathCompareMED This object is used to compare MED among paths learned from confed peers. if this object value is set and AS path contains only AS_CONFED segments then then MED should be compared if this object value is clear and sani…	Enumerationr/w Enumerated Values: 1 set 2 clear	.1.3.6.1.4.1.10876.101.2.77.14.1.24
fsMIBgp4RflbgpClusterId The configured Cluster-ID of the local router. By default, when the BGP speaker acts as Route Reflector, the BGP Identifier is used as the cluster id. Administrator can overwrite the default cluster-id by configuring th…	OctetStringr/w Constraints: range: 4-4	.1.3.6.1.4.1.10876.101.2.77.14.1.25
fsMIBgp4RflRflSupport The desired support of the Route Reflector in the cluster. Note that none(1) value is for read-only. This object can be set only if fsMIBgp4LocalAS is configured.	Enumerationr/w Enumerated Values: 1 none 2 clientsupport 3 noClientSupport	.1.3.6.1.4.1.10876.101.2.77.14.1.26
fsMIBgp4RfdCutOff The figure-of-merit value above which the route will be suppressed. This object can be set only if fsMIBgp4RfdAdminStatus is disabled is set to down and fsMIBgp4LocalAS is configured.	Integer32r/w Constraints: range: 2000-3999	.1.3.6.1.4.1.10876.101.2.77.14.1.27
fsMIBgp4RfdReuse The figure-of-merit value below which the suppressed route will be reused. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fsMIBgp4LocalAS is configured.	Integer32r/w Constraints: range: 100-1999	.1.3.6.1.4.1.10876.101.2.77.14.1.28
fsMIBgp4RfdCeiling The highest value the figure-of-merit can attain.	Integer32 Constraints: range: 4000-10000	.1.3.6.1.4.1.10876.101.2.77.14.1.29
fsMIBgp4RfdMaxHoldDownTime Maximum time (in seconds) a route can be suppressed. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fsMIBgp4LocalAS is configured.	Integer32r/w Constraints: range: 1800-10800	.1.3.6.1.4.1.10876.101.2.77.14.1.30
fsMIBgp4RfdDecayHalfLifeTime The time duration in seconds during which the figure-of-merit will be reduced by half. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fsMIBgp4LocalAS is configured.	Integer32r/w Constraints: range: 600-2700	.1.3.6.1.4.1.10876.101.2.77.14.1.31
fsMIBgp4RfdDecayTimerGranularity Time granularity in seconds used to perform all decay calculations. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fsMIBgp4LocalAS is configured.	Integer32r/w Constraints: range: 1-10800	.1.3.6.1.4.1.10876.101.2.77.14.1.32
fsMIBgp4RfdReuseTimerGranularity Time interval between evaluations of the reuse lists. This object can be set only if fsMIBgp4RfdAdminStatus is disabled and fsMIBgp4LocalAS is configured.	Integer32r/w Constraints: range: 15-10800	.1.3.6.1.4.1.10876.101.2.77.14.1.33
fsMIBgp4RfdReuseIndxArraySize Size of reuse index arrays.This object can be set only if fsMIBgp4GlobalAdminStatus is set to down and fsMIBgp4LocalAS is configured.	Integer32r/w Constraints: range: 256-65535	.1.3.6.1.4.1.10876.101.2.77.14.1.34
fsMIBgp4RfdAdminStatus The desired state of the RouteFlap Dampening feature of the BGP system. The SupermicroBGP4 speaker's route flap dampending is functionally active only when the RFD admin status is enabled. The RFD admin status can be en…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.14.1.35
fsMIBgp4CommMaxInFTblEntries Maximum Number of Entries in the Input Community Filter Table. This object can not be set to a higher value than the initial value of the object.However initial value can be changed in inc/system.size file	Integer32r/w Constraints: range: 1-50000	.1.3.6.1.4.1.10876.101.2.77.14.1.36
fsMIBgp4CommMaxOutFTblEntries Maximum number of entries in the outgoing community filter table. This object can not be set to a higher value than the initial value of the object.However initial value can be changed in inc/system.size file	Integer32r/w Constraints: range: 1-50000	.1.3.6.1.4.1.10876.101.2.77.14.1.37
fsMIBgp4ExtCommMaxInFTblEntries Maximum Number of Entries in the Input Extended Community Filter Table. This object can not be set to a higher value than the initial value of the object.However initial value can be changed in inc/system.size file	Integer32r/w Constraints: range: 1-10000	.1.3.6.1.4.1.10876.101.2.77.14.1.38
fsMIBgp4ExtCommMaxOutFTblEntries Maximum number of entries in the outgoing extended community filter table. This object can not be set to a higher value than the initial value of the object.However initial value can be changed in inc/system.size file	Integer32r/w Constraints: range: 1-10000	.1.3.6.1.4.1.10876.101.2.77.14.1.39
fsMIBgp4CapabilitySupportAvailable This variable determines whether the Capability Advertisement Support is enabled or not.This object can be set only if fsMIBgp4GlobalAdminStatus is set to down and fsMIBgp4LocalAS is configured.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.10876.101.2.77.14.1.40
fsMIBgp4MaxCapsPerPeer The maximum number of Capabilities that can be supported per peer or received from peer. This object can not be set to a higher value than the initial value of the object.However initial value can be changed in inc/syst…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.10876.101.2.77.14.1.41
fsMIBgp4MaxInstancesPerCap The maximum number of Instances of same Capability code can be advertised to peer or received from peer. This object can not be set to a higher value than the initial value of the object.However initial value can be cha…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.10876.101.2.77.14.1.42
fsMIBgp4MaxCapDataSize The maximum size of the Capability Data size of each Capability. To enable packing, the size should be multiples of 4. This object can not be set to a higher value than the initial value of the object.However initial va…	Integer32r/w Constraints: range: 4-252	.1.3.6.1.4.1.10876.101.2.77.14.1.43
fsMIBgp4PreferenceValue Preference value for RIP routes. Use '0' to set default value	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.2.77.14.1.44
fsMIBgp4ContextStatus this is used to enable or disable status of context	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.14.1.45
fsMIBgp4IBGPMaxPaths Maximum number of internal BGP multipath routes to be added per destination network in Routing table. When this object takes the value 1, then only best route is added to Forwarding table. This configuration will have e…	Integer32r/w Constraints: range: 1-64	.1.3.6.1.4.1.10876.101.2.77.14.1.46
fsMIBgp4EBGPMaxPaths Maximum number of external BGP multipath routes to be added per destination network in Routing table. When this object takes the value 1, then only best route is added to Forwarding table. This configuration will have e…	Integer32r/w Constraints: range: 1-64	.1.3.6.1.4.1.10876.101.2.77.14.1.47
fsMIBgp4EIBGPMaxPaths Maximum number of external plus internal BGP multipath routes (with same AS PATH) to be added per destination network in Routing table. When this object takes the value 1, then only best route is added to Forwarding tab…	Integer32r/w Constraints: range: 1-64	.1.3.6.1.4.1.10876.101.2.77.14.1.48
fsMIBgp4OperIBGPMaxPaths Operational value for Maximum number of internal BGP multipath routes to be added per destination network in Routing table. When this object takes the value 1, then only best route is added to Forwarding table.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.10876.101.2.77.14.1.49
fsMIBgp4OperEBGPMaxPaths Operational value for Maximum number of external BGP multipath routes that to be added per destination network in Routing table. When this object takes the value 1, then only best route is added to Forwarding table.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.10876.101.2.77.14.1.50
fsMIBgp4OperEIBGPMaxPaths Operational value for Maximum number of external plus internal BGP multipath routes (with same AS PATH) to be added in Routing table. When this object takes the value 1, then only best route is added to Forwarding tabl…	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.10876.101.2.77.14.1.51
fsMIBgp4FourByteASNSupportStatus This object is used to enable or disable 4 byte ASN support in BGP Speaker. This can be configured only if fsMIBgp4GlobalAdminStatus is down.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.14.1.52
fsMIBgp4FourByteASNotationType This object denotes the notation to be used to display the 4 byte ASN. This will change only the way the AS number is represented within router show commands in the Command Line Interface (CLI) framework. This object ca…	Enumerationr/w Enumerated Values: 1 asplain 2 asdot	.1.3.6.1.4.1.10876.101.2.77.14.1.53
fsMIBgp4LocalAsNo This is local autonomous system number specific to a Context.	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.14.1.54
fsMIBgp4RIBRoutes This is the total number of the routes present in the RIB of a context at the given instance.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.2.77.14.1.55

A table describing the configuration of metric values to
the redistributed routes.

fsMIBgp4RRDMetricEntry row .1.3.6.1.4.1.10876.101.2.77.15.1

Information describing the configuration of single entry.

Indexes

fsMIBgp4ContextId fsMIBgp4RRDMetricProtocolId

Column	Syntax	OID
fsMIBgp4RRDMetricProtocolId Protocol Id for which the Metric value needs to be changed by the User.	Enumeration Enumerated Values: 1 ospf 2 rip 3 connected 4 static	.1.3.6.1.4.1.10876.101.2.77.15.1.1
fsMIBgp4RRDMetricValue The Metric value to be considered instead of the default value from RTM for the protocol specified. If the value not secified by the user, default metric value is considered.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.2.77.15.1.2

This table is used to configure the incoming filter status
for a given community value

fsMIBgp4CommInFilterEntry row .1.3.6.1.4.1.10876.101.2.77.16.1.1

Incoming Communities Filter Table Entry

Indexes

fsMIBgp4ContextId fsMIBgp4InFilterCommVal

Column	Syntax	OID
fsMIBgp4InFilterCommVal The community value for which the input filtering policy is to be updated	Unsigned32 Constraints: range: 65536-4294901759 range: 4294967041-4294967043	.1.3.6.1.4.1.10876.101.2.77.16.1.1.1
fsMIBgp4CommIncomingFilterStatus Incoming filtering policy for the community. o none - is for read-only o accept - Accept the community value. o deny - Deny the community value.	Enumerationr/w Enumerated Values: 1 none 2 accept 3 deny	.1.3.6.1.4.1.10876.101.2.77.16.1.1.2
fsMIBgp4InFilterRowStatus Row status for creating entries into this table.This object can be set only if fsMIBgp4LocalAs is configured.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.2.77.16.1.1.3

This table is used to configure the outgoing filter status
for a given community value

fsMIBgp4CommOutFilterEntry row .1.3.6.1.4.1.10876.101.2.77.16.2.1

Outgoing Communities Filter Table Entry

Indexes

fsMIBgp4ContextId fsMIBgp4OutFilterCommVal

Column	Syntax	OID
fsMIBgp4OutFilterCommVal The community value for which the outgoing filtering policy is to be updated	Unsigned32 Constraints: range: 65536-4294901759 range: 4294967041-4294967043	.1.3.6.1.4.1.10876.101.2.77.16.2.1.1
fsMIBgp4CommOutgoingFilterStatus Outgoing filtering policy for the community. o none - is for read-only o advertise - Advertise the community value. o filter - Filter the community value.	Enumerationr/w Enumerated Values: 1 none 2 advertise 3 filter	.1.3.6.1.4.1.10876.101.2.77.16.2.1.2
fsMIBgp4OutFilterRowStatus Row status for creating entries into this table.This object can be set only if fsMIBgp4LocalAs is configured.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.2.77.16.2.1.3

This table is used to configure the incoming filter status
for a given extended community value

fsMIBgp4ExtCommInFilterEntry row .1.3.6.1.4.1.10876.101.2.77.17.1.1

Incoming Extended Communities Filter Table Entry

Indexes

fsMIBgp4ContextId fsMIBgp4ExtCommInFilterCommVal

Column	Syntax	OID
fsMIBgp4ExtCommInFilterCommVal The extended community value for which the input filtering policy is to be updated	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.10876.101.2.77.17.1.1.1
fsMIBgp4ExtCommIncomingFilterStatus Incoming filtering policy for the extended community. o none - is for read-only o accept - Accept the extended community value. o deny - Deny the extended community value.	Enumerationr/w Enumerated Values: 1 none 2 accept 3 deny	.1.3.6.1.4.1.10876.101.2.77.17.1.1.2
fsMIBgp4ExtCommInFilterRowStatus Row Status for creating the entries into this table.This object can be set only if fsMIBgp4LocalAs is configured.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.2.77.17.1.1.3

This table is used to configure the outgoing filter status
for a given extended community value

fsMIBgp4ExtCommOutFilterEntry row .1.3.6.1.4.1.10876.101.2.77.17.2.1

Outgoing Extended Communities Filter Table Entry

Indexes

fsMIBgp4ContextId fsMIBgp4ExtCommOutFilterCommVal

Column	Syntax	OID
fsMIBgp4ExtCommOutFilterCommVal The extended community value for which the outgoing filtering policy is to be updated	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.10876.101.2.77.17.2.1.1
fsMIBgp4ExtCommOutgoingFilterStatus Outgoing filtering policy for the extended community. o none - is for read-only o advertise - Advertise the extended community value. o filter - Filter the extended community value.	Enumerationr/w Enumerated Values: 1 none 2 advertise 3 noadvertise	.1.3.6.1.4.1.10876.101.2.77.17.2.1.2
fsMIBgp4ExtCommOutFilterRowStatus Row Status to create entries into this table.This object can be set only if fsMIBgp4LocalAs is configured.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.2.77.17.2.1.3

TCP MD5 Authientication Table

fsMIBgp4TCPMD5AuthEntry row .1.3.6.1.4.1.10876.101.2.77.18.1.1

Entry corresponds to the TCP MD5 authentication password.

Indexes

fsMIBgp4ContextId fsMIBgp4TCPMD5AuthPeerType fsMIBgp4TCPMD5AuthPeerAddr

Column	Syntax	OID
fsMIBgp4TCPMD5AuthPeerType Address Family Identifier of the peer remote address.	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.18.1.1.1
fsMIBgp4TCPMD5AuthPeerAddr The IP address of the peer for which the TCP MD5 Authentication Password has to be set. to be read.	OctetString Constraints: range: 1-16	.1.3.6.1.4.1.10876.101.2.77.18.1.1.2
fsMIBgp4TCPMD5AuthPassword The TCP MD5 Authentication Password that has to be sent with all TCP packets originated from the peer.	OctetStringr/w Constraints: range: 1-80	.1.3.6.1.4.1.10876.101.2.77.18.1.1.3
fsMIBgp4TCPMD5AuthPwdSet This object indicates whether TCP MD5 password needs to be set/reset for the peer. This object needs to be set before the object fsMIBgp4TCPMD5AuthPassword can be set.	Enumerationr/w Enumerated Values: 1 set 2 clear	.1.3.6.1.4.1.10876.101.2.77.18.1.1.4

BGP peer confederation table, this table contains information
about the Member-ASs of the confederation

fsMIBgpAscConfedPeerEntry row .1.3.6.1.4.1.10876.101.2.77.19.1.1

Entry containing information about a member-AS of the confederation.

Indexes

fsMIBgp4ContextId fsMIBgpAscConfedPeerASNo

Column	Syntax	OID
fsMIBgpAscConfedPeerASNo The local AS number of member-AS, a value of zero indicates the absence of this value	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.4.1.10876.101.2.77.19.1.1.1
fsMIBgpAscConfedPeerStatus This object is used to enable or disable the member-AS. Use disable, if member-AS entry needs to disabled, Use enable, if member-AS entry needs to be enabled.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.19.1.1.2

BGP peer table.  This table contains, one entry per BGP peer,
information about the connections with BGP peers.

fsMIBgp4MpeBgpPeerEntry row .1.3.6.1.4.1.10876.101.2.77.20.1

Entry containing information about the connection with a BGP peer.

Indexes

fsMIBgp4ContextId fsMIBgp4mpebgpPeerRemoteAddrType fsMIBgp4mpebgpPeerRemoteAddr

Column	Syntax	OID
fsMIBgp4mpebgpPeerIdentifier The BGP Identifier of this entry's BGP peer.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.20.1.1
fsMIBgp4mpebgpPeerRemoteAddrType Type of the remote peer	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.20.1.2
fsMIBgp4mpebgpPeerLocalAs It is used to configure as Local As per peer	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.20.1.3
fsMIBgp4mpebgpPeerState The BGP peer connection state.	Enumeration Enumerated Values: 1 idle 2 connect 3 active 4 opensent 5 openconfirm 6 established	.1.3.6.1.4.1.10876.101.2.77.20.1.4
fsMIBgp4mpebgpPeerAdminStatus The desired state of the BGP connection. A transition from 'stop' to 'start' will cause the BGP Start Event to be generated. A transition from 'start' to 'stop' will cause the BGP Stop Event to be generated. This para…	Enumerationr/w Enumerated Values: 1 stop 2 start 3 autostart	.1.3.6.1.4.1.10876.101.2.77.20.1.5
fsMIBgp4mpebgpPeerNegotiatedVersion The negotiated version of BGP running between the two peers.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.2.77.20.1.6
fsMIBgp4mpebgpPeerLocalAddr The local IP address of this entry's BGP connection.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.20.1.7
fsMIBgp4mpebgpPeerLocalPort The local port for the TCP connection between the BGP peers.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.2.77.20.1.8
fsMIBgp4mpebgpPeerRemoteAddr The remote IP address of this entry's BGP peer.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.20.1.9
fsMIBgp4mpebgpPeerRemotePort The remote port for the TCP connection between the BGP peers. Note that the objects bgpPeerLocalAddr, bgpPeerLocalPort, bgpPeerRemoteAddr and bgpPeerRemotePort provide the appropriate reference to the standard MIB TCP c…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.2.77.20.1.10
fsMIBgp4mpebgpPeerRemoteAs The remote autonomous system number.	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.20.1.11
fsMIBgp4mpebgpPeerInUpdates The number of BGP UPDATE messages received on this connection. This object should be initialized to zero (0) when the connection is established.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.2.77.20.1.12
fsMIBgp4mpebgpPeerOutUpdates The number of BGP UPDATE messages transmitted on this connection. This object should be initialized to zero (0) when the connection is established.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.2.77.20.1.13
fsMIBgp4mpebgpPeerInTotalMessages The total number of messages received from the remote peer on this connection. This object should be initialized to zero when the connection is established.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.2.77.20.1.14
fsMIBgp4mpebgpPeerOutTotalMessages The total number of messages transmitted to the remote peer on this connection. This object should be initialized to zero when the connection is established.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.2.77.20.1.15
fsMIBgp4mpebgpPeerLastError The last error code and subcode seen by this peer on this connection. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte c…	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.10876.101.2.77.20.1.16
fsMIBgp4mpebgpPeerFsmEstablishedTransitions The total number of times the BGP FSM transitioned into the established state.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.2.77.20.1.17
fsMIBgp4mpebgpPeerFsmEstablishedTime This timer indicates how long (in seconds) this peer has been in the Established state or how long since this peer was last in the Established state. It is set to zero when a new peer is configured or the router is boo…	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.2.77.20.1.18
fsMIBgp4mpebgpPeerConnectRetryInterval Time interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.2.77.20.1.19
fsMIBgp4mpebgpPeerHoldTime Time interval in seconds for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker by using the smaller of the value in bgpPeerHoldTimeConfigured and the Hold Time receive…	Integer32 Constraints: range: 0-0 range: 3-65535	.1.3.6.1.4.1.10876.101.2.77.20.1.20
fsMIBgp4mpebgpPeerKeepAlive Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with bgpPeerHoldTime, it has the same proportion as what b…	Integer32 Constraints: range: 0-21845	.1.3.6.1.4.1.10876.101.2.77.20.1.21
fsMIBgp4mpebgpPeerHoldTimeConfigured Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an O…	Integer32r/w Constraints: range: 0-0 range: 3-65535	.1.3.6.1.4.1.10876.101.2.77.20.1.22
fsMIBgp4mpebgpPeerKeepAliveConfigured Time interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeer…	Integer32r/w Constraints: range: 0-21845	.1.3.6.1.4.1.10876.101.2.77.20.1.23
fsMIBgp4mpebgpPeerMinASOriginationInterval Time interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 15 seconds.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.2.77.20.1.24
fsMIBgp4mpebgpPeerMinRouteAdvertisementInterval Time interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.2.77.20.1.25
fsMIBgp4mpebgpPeerInUpdateElapsedTime Elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time bgpPeerInUpdates is incremented, the value of this object is set to zero (0).	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.2.77.20.1.26
fsMIBgp4mpebgpPeerEndOfRIBMarkerSentStatus This object indicates that whether the End-Of-RIB marker sent to peer or not	Enumeration Enumerated Values: 0 none 1 true 2 false	.1.3.6.1.4.1.10876.101.2.77.20.1.27
fsMIBgp4mpebgpPeerEndOfRIBMarkerReceivedStatus This object indicates that whether the End-Of-RIB marker received from peer or not	Enumeration Enumerated Values: 0 none 1 true 2 false	.1.3.6.1.4.1.10876.101.2.77.20.1.28
fsMIBgp4mpebgpPeerRestartMode This object indicates whether the peer BGP speaker is restarting speaker or receiving speaker or not having GR capability	Enumeration Enumerated Values: 1 restarting 2 receiving 3 none	.1.3.6.1.4.1.10876.101.2.77.20.1.29
fsMIBgp4mpePeerRestartTimeInterval This is the time (in seconds) received from peer through GR capability of open message. This is used in receiving speaker to make sure that the restarting speaker restarted within this interval	Integer32 Constraints: range: 1-4096	.1.3.6.1.4.1.10876.101.2.77.20.1.30
fsMIBgp4mpePeerAllowAutomaticStart This MIB object specifies whether BGP session with the associated peer can be started automatically. This object when set to 'disabled', requires manual start for initiating BGP session with the peer via MIB object 'fsM…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.20.1.31
fsMIBgp4mpePeerAllowAutomaticStop This MIB object specifies whether a BGP connection needs to be automatically stopped after a TCP connect-retry count value specified by MIB object 'fsMIBgp4mpePeerTcpConnectRetryCnt'. The resources allocated for the BGP…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.20.1.32
fsMIBgp4mpebgpPeerIdleHoldTimeConfigured IdleHoldTime specifies the length of time the BGP peer is held in the Idle state prior to allowing the next automatic restart. The IdleHoldTime is configured only when the fsMIBgp4mpePeerAllowAutomaticStart is Enabled o…	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.10876.101.2.77.20.1.33
fsMIBgp4mpeDampPeerOscillations The DampPeerOscillations option specifies that the implementation engages additional logic to damp the oscillations of BGP peers in the face of series of automatic start and automatic stop operations in the IDLE state.T…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.20.1.34
fsMIBgp4mpePeerDelayOpen This MIB object allows configuration option to enable/disable delay in sending of OPEN messages to the BGP peer for a specific time period (DelayOpenTime). The delay allows the remote BGP Peer to send the first OPEN mes…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.20.1.35
fsMIBgp4mpebgpPeerDelayOpenTimeConfigured The DelayOpen time specifies the amount of time the BGP Peer should delay in sending the OPEN message to the remote peer. If the fsMIBgp4mpePeerDelayOpen option is enabled, the DelayOpen time can bei configured. The def…	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.2.77.20.1.36
fsMIBgp4mpePeerPrefixUpperLimit BGP speaker imposes a locally-configured, upper bound on the number of address prefixes the speaker is willing to accept from a neighbor. The default value is calculated as the following: fsMIBgp4MaxNoofR…	Integer32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.10876.101.2.77.20.1.37
fsMIBgp4mpePeerTcpConnectRetryCnt This counter denotes the Maximum number of times the BGP Peer has tried to issue a TCP-Connect with its neighboring peers. The default value for the counter is set as 5.	Integer32r/w Constraints: range: 1-50	.1.3.6.1.4.1.10876.101.2.77.20.1.38
fsMIBgp4mpePeerTcpCurrentConnectRetryCnt This counter denotes the number of times the BGP Peer has tried to issue a TCP-Connect with its neighboring peers. It is an internal value. It increments for each Autostop event. If the 'fsMIBgp4mpePeerTcpCurrentConnect…	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.10876.101.2.77.20.1.39
fsMIBgp4mpeIsPeerDamped This MIB object specifies the PeerDamped Status. If it is enabled, it denotes that the peer is in damped state. If it is disabled, it denotes that either the peer has recovered from the damped state or not entered into …	Enumeration Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.20.1.40
fsMIBgp4mpePeerSessionAuthStatus This object indicates whether peer-session is TCP MD5/TCP-AO authenticated or not. If no session is established yet, its value is no-session	Enumeration Enumerated Values: 1 nosession 2 authenticatedMd5 3 unauthenticated 4 authenticatedTcpAo	.1.3.6.1.4.1.10876.101.2.77.20.1.41
fsMIBgp4mpePeerTCPAOKeyIdInUse Key id of the MKT which is used by the TCP session of the peer, this field will be valid only when fsMIBgp4mpePeerSessionAuthStatus has value authenticatedTcpAo	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.2.77.20.1.42
fsMIBgp4mpePeerTCPAOAuthNoMKTDiscard Discard packet for the peer, if packets are received with TCP-AO and no matching MKT is found, default value is accept	Enumerationr/w Enumerated Values: 1 accept 2 discard	.1.3.6.1.4.1.10876.101.2.77.20.1.43
fsMIBgp4mpePeerTCPAOAuthICMPAccept Accept ICMPv4 type 3 & ICMPv6 type 1 messages for the TCP-AO authenticated peer, default value is ignore	Enumerationr/w Enumerated Values: 1 accept 2 ignore	.1.3.6.1.4.1.10876.101.2.77.20.1.44
fsMIBgp4mpePeerIpPrefixNameIn This object is used to configure the IP Prefix list name in IN direction for this peer entry.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.10876.101.2.77.20.1.45
fsMIBgp4mpePeerIpPrefixNameOut This object is used to configure the IP Prefix list name in OUT direction for this peer entry.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.10876.101.2.77.20.1.46

The BGP-4 Received Path Attribute Table
contains information about paths to
destination networks received from all
BGP4 peers.

fsMIBgp4MpeBgp4PathAttrEntry row .1.3.6.1.4.1.10876.101.2.77.21.1

Information about a path to a network.

Indexes

fsMIBgp4ContextId fsMIBgp4mpebgp4PathAttrRouteAfi fsMIBgp4mpebgp4PathAttrRouteSafi fsMIBgp4mpebgp4PathAttrIpAddrPrefix fsMIBgp4mpebgp4PathAttrIpAddrPrefixLen fsMIBgp4mpebgp4PathAttrPeerType fsMIBgp4mpebgp4PathAttrPeer

Column	Syntax	OID
fsMIBgp4mpebgp4PathAttrRouteAfi The AFI of the prefix	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.21.1.1
fsMIBgp4mpebgp4PathAttrRouteSafi The SAFI of the prefix	SUPERMICRO-BGP-MIBBgpSafi Type Values: 0 unknown 1 unicast 4 labelledIpv4 128 vpnv4	.1.3.6.1.4.1.10876.101.2.77.21.1.2
fsMIBgp4mpebgp4PathAttrPeerType The AFI of the peer	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.21.1.3
fsMIBgp4mpebgp4PathAttrPeer The IP address of the peer where the path information was learned.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.21.1.4
fsMIBgp4mpebgp4PathAttrIpAddrPrefixLen Length in bits of the IP address prefix in the Network Layer Reachability Information field.	Integer32 Constraints: range: 0-32	.1.3.6.1.4.1.10876.101.2.77.21.1.5
fsMIBgp4mpebgp4PathAttrIpAddrPrefix An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by bgp4PathAttrIpAddrPrefixLen. Any bits beyond the length specified by…	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.21.1.6
fsMIBgp4mpebgp4PathAttrOrigin The ultimate origin of the path information.	Enumeration Enumerated Values: 1 igp 2 egp 3 incomplete	.1.3.6.1.4.1.10876.101.2.77.21.1.7
fsMIBgp4mpebgp4PathAttrASPathSegment The sequence of AS path segments. Each AS path segment is represented by a triple <type, length, value>. The type is a 1-octet field which has two possible values: 1 AS_SET: unordered set of ASs, traversed by a …	OctetString Constraints: range: 2-255	.1.3.6.1.4.1.10876.101.2.77.21.1.8
fsMIBgp4mpebgp4PathAttrNextHop The address of the border router that should be used for the destination network.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.21.1.9
fsMIBgp4mpebgp4PathAttrMultiExitDisc This metric is used to discriminate between multiple exit points to an adjacent autonomous system. A value of -1 indicates the absence of this attribute.	Integer32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.10876.101.2.77.21.1.10
fsMIBgp4mpebgp4PathAttrLocalPref The originating BGP4 speaker's degree of preference for an advertised route. A value of -1 indicates the absence of this attribute.	Integer32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.10876.101.2.77.21.1.11
fsMIBgp4mpebgp4PathAttrAtomicAggregate Whether or not the local system has selected a less specific route without selecting a more specific route.	Enumeration Enumerated Values: 1 lessSpecificRrouteNotSelected 2 lessSpecificRouteSelected	.1.3.6.1.4.1.10876.101.2.77.21.1.12
fsMIBgp4mpebgp4PathAttrAggregatorAS The AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute.	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.21.1.13
fsMIBgp4mpebgp4PathAttrAggregatorAddr The IP address of the last BGP4 speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.2.77.21.1.14
fsMIBgp4mpebgp4PathAttrCalcLocalPref The degree of preference calculated by the receiving BGP4 speaker for an advertised route. A value of -1 indicates the absence of this attribute.	Integer32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.10876.101.2.77.21.1.15
fsMIBgp4mpebgp4PathAttrBest An indication of whether or not this route was chosen as the best BGP4 route.	Enumeration Enumerated Values: 1 nonbest 2 best 3 stale	.1.3.6.1.4.1.10876.101.2.77.21.1.16
fsMIBgp4mpebgp4PathAttrCommunity The community values received for this destinatin from the peer	OctetString Constraints: range: 0-800	.1.3.6.1.4.1.10876.101.2.77.21.1.17
fsMIBgp4mpebgp4PathAttrOriginatorId The Originator-ID identifying the router that initially advertised this destination to a Route Reflector. A value of 0.0.0.0 indicates the absence of this attribute	OctetString Constraints: range: 4-4	.1.3.6.1.4.1.10876.101.2.77.21.1.18
fsMIBgp4mpebgp4PathAttrClusterList A sequence of four octet long values Cluster-IDs representing the reflection path that the route has passed. Each four octet long value represents the ID of a cluster that the route has traversed. A length of zero (0) i…	OctetString Constraints: range: 0-4096	.1.3.6.1.4.1.10876.101.2.77.21.1.19
fsMIBgp4mpebgp4PathAttrExtCommunity The extended community values received for this destinatin from the peer	OctetString Constraints: range: 0-800	.1.3.6.1.4.1.10876.101.2.77.21.1.20
fsMIBgp4mpebgp4PathAttrUnknown One or more path attributes not understood by this BGP4 speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if any, are not recorded by this object.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.2.77.21.1.21
fsMIBgp4mpebgp4PathAttrLabel MPLS Label received for this destination from the peer	OctetString Constraints: range: 0-24	.1.3.6.1.4.1.10876.101.2.77.21.1.22
fsMIBgp4mpebgp4PathAttrAS4PathSegment The sequence of AS path segments. Each AS path segment is represented by a triple <type, length, value>. The type is a 1-octet field which has two possible values: 1 AS_SET: unordered set of ASs, traversed by a …	OctetString Constraints: range: 2-255	.1.3.6.1.4.1.10876.101.2.77.21.1.23
fsMIBgp4mpebgp4PathAttrAggregatorAS4 The 4 Byte AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute.	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.21.1.24

BGP Peer Extension Table. The entries in the table specifies
the additional features supported for a peer by futureBGP4
Speaker in addition to the features specified as in bgpPeerTable
(described in  stdbgp4.mib.). All entries in this table can be
configured only if fsMIBgp4LocalAs has be configured.

fsMIBgp4MpePeerExtEntry row .1.3.6.1.4.1.10876.101.2.77.22.1

Entry containing information about the additional features supported
for a peer by futureBGP4 Speaker.

Indexes

fsMIBgp4ContextId fsMIBgp4mpePeerExtPeerType fsMIBgp4mpePeerExtPeerRemoteAddr

Column	Syntax	OID
fsMIBgp4mpePeerExtPeerType The Type of the remote peer	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.22.1.1
fsMIBgp4mpePeerExtPeerRemoteAddr The remote IP address of this entry's BGP peer.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.22.1.2
fsMIBgp4mpePeerExtConfigurePeer This object is used to create or delete a peer. If called with create and no matching peer exists, then a new peer entry will be created. The admin status of this newly created peer will be stop. To enable the peer set …	Enumerationr/w Enumerated Values: 1 create 2 delete	.1.3.6.1.4.1.10876.101.2.77.22.1.3
fsMIBgp4mpePeerExtPeerRemoteAs The remote autonomous system number of the Peer. The peer admin status can be made up only if this object is configured for a valid AS number. When OPEN message is received from this peer during the BGP Connection estab…	Unsigned32r/w Constraints: range: 1-4294967295	.1.3.6.1.4.1.10876.101.2.77.22.1.4
fsMIBgp4mpePeerExtEBGPMultiHop This objects enables the BGP4 Speaker to accept or attempt connections to external peers residing on network that are not directly connected. By default, only directly connected EBGP peers are allowed. For the internal …	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.22.1.5
fsMIBgp4mpePeerExtEBGPHopLimit This objects enables the BGP4 Speaker to accept or attempt connections to external peers residing on network that are not directly connected and seperated by a maximum hop limit as configured by this object. For the in…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.10876.101.2.77.22.1.6
fsMIBgp4mpePeerExtNextHopSelf This object specifies how the next hop attribute sent in the update messages to this peer has to be generated. When the object takes the value of self,the next Hop attribute will always be the sender Local Address els…	Enumerationr/w Enumerated Values: 1 automatic 2 self	.1.3.6.1.4.1.10876.101.2.77.22.1.7
fsMIBgp4mpePeerExtRflClient This object specifies whether the peer is Client peer or Non-Client peer. By default, the peer is created as Non-Client Peer.	Enumerationr/w Enumerated Values: 1 nonClient 2 client	.1.3.6.1.4.1.10876.101.2.77.22.1.8
fsMIBgp4mpePeerExtTcpSendBufSize This object configures the tcp window size on the sender side.	Integer32r/w Constraints: range: 4096-65536	.1.3.6.1.4.1.10876.101.2.77.22.1.9
fsMIBgp4mpePeerExtTcpRcvBufSize This object configures the tcp window size on the receiver side.	Integer32r/w Constraints: range: 4096-65536	.1.3.6.1.4.1.10876.101.2.77.22.1.10
fsMIBgp4mpePeerExtLclAddress This object specifies which address should be used as the source address of the TCP session initiated with the Peer. By default this object takes value as 0 and the source address of the TCP session is filled by TCP. Th…	SUPERMICRO-BGP-MIBInetAddressr/w Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.22.1.11
fsMIBgp4mpePeerExtNetworkAddress This object specifies the remote peer's network address. TCP connection is established using the peer's remote-address. If the peer's remote-address is a IPv4 address, the peer's network address carries the IPv6 network…	SUPERMICRO-BGP-MIBInetAddressr/w Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.22.1.12
fsMIBgp4mpePeerExtGateway This object specifies the gateway router's address that will be used as nexthop in the routes advertised to the peer. This ensures that the traffic coming from this peer is routed through this gateway.	SUPERMICRO-BGP-MIBInetAddressr/w Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.22.1.13
fsMIBgp4mpePeerExtCommSendStatus Community Send status of the peer. o none - is for read-only o send - send communities to this peer o donotsend - do not send communities to this peer.	Enumerationr/w Enumerated Values: 1 none 2 send 3 donotsend	.1.3.6.1.4.1.10876.101.2.77.22.1.14
fsMIBgp4mpePeerExtECommSendStatus Extended Community Send status of the peer. o none - is for read-only o send - send extended communities to this peer o donotsend - do not send extended communities to this peer.	Enumerationr/w Enumerated Values: 1 none 2 send 3 donotsend	.1.3.6.1.4.1.10876.101.2.77.22.1.15
fsMIBgp4mpePeerExtPassive This object is used to set a peer connection to be passive, that means the speaker will not initiate the session with that peer instead it waits for the remote peer to initiate the session	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.22.1.16
fsMIBgp4mpePeerExtDefaultOriginate If this object is set to enable/disable the advertisement of the default route to the peer. This object overrides the global default route configuration (fsMIBgp4DefaultOriginate) and always send a default route to the …	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.22.1.17

BGP4 MED table. This table contains the MED values that are to
be assigned to routes.

fsMIBgp4MpeMEDEntry row .1.3.6.1.4.1.10876.101.2.77.23.1

Entry containing information about the MED value.

Indexes

fsMIBgp4mpeMEDIndex

Column	Syntax	OID
fsMIBgp4mpeMEDIndex This is the index to the table. Any entry in the table can be configured only if fsMIBgp4LocalAs is set.	Integer32 Constraints: range: 1-10	.1.3.6.1.4.1.10876.101.2.77.23.1.1
fsMIBgp4mpeMEDAdminStatus The desired state of this entry. The entries in a row are configurable only if the admin status is DOWN.	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.10876.101.2.77.23.1.2
fsMIBgp4mpeMEDRemoteAS The remote autonomous system with which this entry is associated. A value of zero indicates that this entry is not valid and will not be matched for when the MED value for an update is calculated.	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.23.1.3
fsMIBgp4mpeMEDIPAddrAfi Type of IP address prefix in the Network Layer Reachability Information field in updates. This field needs to be set before setting the object fsMIBgp4mpeMEDIPAddrPrefix.	SUPERMICRO-BGP-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.23.1.4
fsMIBgp4mpeMEDIPAddrSafi Type of IP address prefix in the Network Layer Reachability Information field in updates. This field needs to be set before setting the object fsMIBgp4mpeMEDIPAddrPrefix.	SUPERMICRO-BGP-MIBBgpSafir/w Type Values: 0 unknown 1 unicast 4 labelledIpv4 128 vpnv4	.1.3.6.1.4.1.10876.101.2.77.23.1.5
fsMIBgp4mpeMEDIPAddrPrefix An IP address prefix in the Network Layer Reachability Information field in updates. A value of zero indicates that the entry is not valid and will not be matched for when the MED value for an update is calculated.	SUPERMICRO-BGP-MIBInetAddressr/w Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.23.1.6
fsMIBgp4mpeMEDIPAddrPrefixLen Length in bits of the IP address prefix in the Network Layer Reachability Information field. A value of zero indicates that the entry is not valid and will not be matched for when the MED value for an update is calcul…	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.10876.101.2.77.23.1.7
fsMIBgp4mpeMEDIntermediateAS Comma seperated list of AS numbers that are to be checked against the AS_PATH attribute of the Update. An empty field indicates that the same need not be checked for in the update.Maximum configurable size is 100.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.10876.101.2.77.23.1.8
fsMIBgp4mpeMEDDirection The direction of the update with which the entry is to be associated.	Enumerationr/w Enumerated Values: 1 in 2 out	.1.3.6.1.4.1.10876.101.2.77.23.1.9
fsMIBgp4mpeMEDValue The value assigned to the MED Attribute for the route present in NLRI	Unsigned32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.10876.101.2.77.23.1.10
fsMIBgp4mpeMEDPreference This object specifies whether the value present in this entry takes precedence when the attribute is already present in the update message that has been received.	Enumerationr/w Enumerated Values: 1 false 2 true	.1.3.6.1.4.1.10876.101.2.77.23.1.11
fsMIBgp4mpeMEDVrfName The human-readable name of the VPN.	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.10876.101.2.77.23.1.12

BGP Local Preference table.  This table contains,
the value that is to be assigned to the Local
Preference attibute.

fsMIBgp4MpeLocalPrefEntry row .1.3.6.1.4.1.10876.101.2.77.24.1

Entry containing information about the connection with a BGP peer.

Indexes

fsMIBgp4mpeLocalPrefIndex

Column	Syntax	OID
fsMIBgp4mpeLocalPrefIndex This is the index to the table. Any entry in the table can be configured only if fsMIBgp4mpeLocalAs is set.	Integer32 Constraints: range: 1-10	.1.3.6.1.4.1.10876.101.2.77.24.1.1
fsMIBgp4mpeLocalPrefAdminStatus The desired state of this entry. The entries in a row are configurable only if the admin status is DOWN.	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.10876.101.2.77.24.1.2
fsMIBgp4mpeLocalPrefRemoteAS The remote autonomous system with which this entry is associated. A value of zero indicates that this entry is not valid and will not be matched for when the LocalPref value for an update is calculated.	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.24.1.3
fsMIBgp4mpeLocalPrefIPAddrAfi Type of IP address prefix in the Network Layer Reachability Information field. This field needs to be set before setting the object fsMIBgp4mpeLocalPrefIPAddrPrefix.	SUPERMICRO-BGP-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.24.1.4
fsMIBgp4mpeLocalPrefIPAddrSafi Sub-sequent address family of IP address prefix in the Network Layer Reachability Information field.This field needs to be set before setting the object fsMIBgp4mpeLocalPrefIPAddrPrefix.	SUPERMICRO-BGP-MIBBgpSafir/w Type Values: 0 unknown 1 unicast 4 labelledIpv4 128 vpnv4	.1.3.6.1.4.1.10876.101.2.77.24.1.5
fsMIBgp4mpeLocalPrefIPAddrPrefix An IP address prefix in the Network Layer Reachability Information field. A value of zero indicates that the entry is not valid and will not be matched for when the Local Pref value for an update is calculated.	SUPERMICRO-BGP-MIBInetAddressr/w Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.24.1.6
fsMIBgp4mpeLocalPrefIPAddrPrefixLen Length in bits of the IP address prefix in the Network Layer Reachability Information field. A value of zero indicates that the entry is not valid and will not be matched for when the Local Pref value for an update i…	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.10876.101.2.77.24.1.7
fsMIBgp4mpeLocalPrefIntermediateAS Comma separated list of AS numbers that are to be present in the AS_PATH attribute of the Update. An empty field indicates that the same need not be checked for in the update.Maximum configurable size is 100.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.10876.101.2.77.24.1.8
fsMIBgp4mpeLocalPrefDirection The direction of the update with which the entry is to be associated.	Enumerationr/w Enumerated Values: 1 in 2 out	.1.3.6.1.4.1.10876.101.2.77.24.1.9
fsMIBgp4mpeLocalPrefValue The value assigned to the LP Attribute for the route present in NLRI	Unsigned32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.10876.101.2.77.24.1.10
fsMIBgp4mpeLocalPrefPreference This object specifies whether the value present in this entry takes precedence when the attribute is already present in the update message that has been received.	Enumerationr/w Enumerated Values: 1 false 2 true	.1.3.6.1.4.1.10876.101.2.77.24.1.11
fsMIBgp4mpeLocalPrefVrfName The human-readable name of the VPN.	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.10876.101.2.77.24.1.12

BGP Update Filter Table.  This table contains
Rules to filter out updates based on the AS from
which it is received, NLRI and AS through which it
had passed.

fsMIBgp4MpeUpdateFilterEntry row .1.3.6.1.4.1.10876.101.2.77.25.1

Entry containing information about the updates
that are to be filtered.

Indexes

fsMIBgp4mpeUpdateFilterIndex

Column	Syntax	OID
fsMIBgp4mpeUpdateFilterIndex This is the index to the table. Any entry in the table can be configured only if fsMIBgp4LocalAs is set.	Integer32 Constraints: range: 1-10	.1.3.6.1.4.1.10876.101.2.77.25.1.1
fsMIBgp4mpeUpdateFilterAdminStatus The desired state of this entry. The entries in a row are configurable only if the admin status is DOWN.	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.10876.101.2.77.25.1.2
fsMIBgp4mpeUpdateFilterRemoteAS The remote autonomous system with which this entry is associated. A value of zero indicates that this entry is not valid and will not be matched for when the update is checked.	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.10876.101.2.77.25.1.3
fsMIBgp4mpeUpdateFilterIPAddrAfi Type of IP address prefix in the Network Layer Reachability Information field. This field needs to be set, before setting the object fsMIBgp4mpeUpdateFilterIPAddrPrefix.	SUPERMICRO-BGP-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.25.1.4
fsMIBgp4mpeUpdateFilterIPAddrSafi SAFI of IP address prefix in the Network Layer Reachability Information field. This field needs to be set, before setting the object fsMIBgp4mpeUpdateFilterIPAddrPrefix.	SUPERMICRO-BGP-MIBBgpSafir/w Type Values: 0 unknown 1 unicast 4 labelledIpv4 128 vpnv4	.1.3.6.1.4.1.10876.101.2.77.25.1.5
fsMIBgp4mpeUpdateFilterIPAddrPrefix An IP address prefix in the Network Layer Reachability Information field. A value of zero in this field indicates that the NLRI field may not be matched.	SUPERMICRO-BGP-MIBInetAddressr/w Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.25.1.6
fsMIBgp4mpeUpdateFilterIPAddrPrefixLen Length in bits of the IP address prefix in the Network Layer Reachability Information field. A value of zero in this field indicates that the NLRI field may not be matched.	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.10876.101.2.77.25.1.7
fsMIBgp4mpeUpdateFilterIntermediateAS Comma separated list of AS numbers that are to be present in the AS_PATH attribute of the Update. An empty field indicates that the same need not be checked for in the update.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.10876.101.2.77.25.1.8
fsMIBgp4mpeUpdateFilterDirection The direction of the update with which the entry is to be associated.	Enumerationr/w Enumerated Values: 1 in 2 out	.1.3.6.1.4.1.10876.101.2.77.25.1.9
fsMIBgp4mpeUpdateFilterAction The action to be taken when the characteristics that are specified in the entry is matched.	Enumerationr/w Enumerated Values: 1 allow 2 filter	.1.3.6.1.4.1.10876.101.2.77.25.1.10
fsMIBgp4mpeUpdateFilterVrfName The human-readable name of the VPN.	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.10876.101.2.77.25.1.11

BGP Aggregate Table. The entries in the table
specifies the IP address based on which the routing
information has to be aggregated.

fsMIBgp4MpeAggregateEntry row .1.3.6.1.4.1.10876.101.2.77.26.1

Entry containing information about the IP address
on which the aggregation has to be done.

Indexes

fsMIBgp4mpeAggregateIndex

Column	Syntax	OID
fsMIBgp4mpeAggregateIndex This is the index to the table.Any entry in the table can be configured only if fsMIBgp4LocalAs is set.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.2.77.26.1.1
fsMIBgp4mpeAggregateAdminStatus The desired state of this entry. When the adminstatus is set to up, the aggregate entry will be made active and the aggregate route will be formed for this entry. When the adminstatus is set to down, the aggregate rout…	Enumerationr/w Enumerated Values: 1 up 2 down 3 invalid	.1.3.6.1.4.1.10876.101.2.77.26.1.2
fsMIBgp4mpeAggregateIPAddrAfi Type of IP address prefix in the Network Layer Reachability Information field. This field needs to be set before setting the object fsMIBgp4mpeAggregateIPAddrPrefix.	SUPERMICRO-BGP-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.26.1.3
fsMIBgp4mpeAggregateIPAddrSafi SAFI of IP address prefix in the Network Layer Reachability Information field. This field needs to be set before setting the object fsMIBgp4mpeAggregateIPAddrPrefix.. [Note] SAFI for Carrying Label (4) can't be set. Th…	SUPERMICRO-BGP-MIBBgpSafir/w Type Values: 0 unknown 1 unicast 4 labelledIpv4 128 vpnv4	.1.3.6.1.4.1.10876.101.2.77.26.1.4
fsMIBgp4mpeAggregateIPAddrPrefix An IP address prefix in the Network Layer Reachability Information field. This field is configurable only if the admin status is DOWN	SUPERMICRO-BGP-MIBInetAddressr/w Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.26.1.5
fsMIBgp4mpeAggregateIPAddrPrefixLen Length in bits of the IP address prefix in the Network Layer Reachability Information field. This field is configurable only if the admin status is DOWN.	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.10876.101.2.77.26.1.6
fsMIBgp4mpeAggregateAdvertise This object specifies the route update that should be sent to the peers - summary-only - specifies that only the summarized route has to be advertised to peers. All - specifies that bot…	Enumerationr/w Enumerated Values: 1 summaryOnly 2 all	.1.3.6.1.4.1.10876.101.2.77.26.1.7
fsMIBgp4mpeAggregateVrfName The human-readable name of the VPN.	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.10876.101.2.77.26.1.8
fsMIBgp4mpeAggregateAsSet Enables/Disables the autonomous system set path information. It is an optional parameter	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.10876.101.2.77.26.1.9
fsMIBgp4mpeAggregateAdvertiseRouteMapName The human-readable name for adverise route-map. The route map contains the rules for advertising the routes while aggregation. When we use advertise-map, only advertise-map influences the creation of aggregate entry. In…	OctetStringr/w Constraints: range: 1-20	.1.3.6.1.4.1.10876.101.2.77.26.1.10
fsMIBgp4mpeAggregateSuppressRouteMapName The human-readable name for suppress route-map. The route map contains the rules for suppressing the routes while aggregation. when we use suppress-map configuration along with (summaryonly option set for) fsMIBgp4mpeAg…	OctetStringr/w Constraints: range: 1-20	.1.3.6.1.4.1.10876.101.2.77.26.1.11
fsMIBgp4mpeAggregateAttributeRouteMapName The human-readable name for attribute route-map. The route map contains the rules for setting the attributes the aggregated route. When attribute-map and advertise-map along with fsMIBgp4mpeAggregateAsSet (enable) and o…	OctetStringr/w Constraints: range: 1-20	.1.3.6.1.4.1.10876.101.2.77.26.1.12

Non-BGP routes imported into the BGP RIB can be viewed through this table.
Also allows importing a static route into BGP.After updating the RIB tree,
if there is any change in the best route selected, then the  route is 
updated to the Common Forwarding table.

fsMIBgp4MpeImportRouteEntry row .1.3.6.1.4.1.10876.101.2.77.27.1

Import Route entry.

Indexes

fsMIBgp4ContextId fsMIBgp4mpeImportRoutePrefixAfi fsMIBgp4mpeImportRoutePrefixSafi fsMIBgp4mpeImportRoutePrefix fsMIBgp4mpeImportRoutePrefixLen fsMIBgp4mpeImportRouteProtocol fsMIBgp4mpeImportRouteNextHop fsMIBgp4mpeImportRouteIfIndex fsMIBgp4mpeImportRouteMetric fsMIBgp4mpeImportRouteVrf

Column	Syntax	OID
fsMIBgp4mpeImportRoutePrefixAfi Type of Prefix of the route to be imported.	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.27.1.1
fsMIBgp4mpeImportRoutePrefixSafi SAFI of Prefix of the route to be imported. Only UNICAST (1) is allowed right now. Route can be imported into VRF by providing SAFI (1) and VRF name.	SUPERMICRO-BGP-MIBBgpSafi Type Values: 0 unknown 1 unicast 4 labelledIpv4 128 vpnv4	.1.3.6.1.4.1.10876.101.2.77.27.1.2
fsMIBgp4mpeImportRoutePrefix Prefix of the route to be imported.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.27.1.3
fsMIBgp4mpeImportRoutePrefixLen Prefix length of the route.	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.10876.101.2.77.27.1.4
fsMIBgp4mpeImportRouteProtocol Protocol value for Non-BGP routes. 2- LOCAL, 3 - STATIC, 8 - RIP, 13 - OSPF. Only STATIC routes (protocol 3) can be added through this table. However all non-BGP protocol (Local, Static, RIP, OSPF) routes can be v…	Integer32 Constraints: range: 2-3 range: 8-8 range: 13-13	.1.3.6.1.4.1.10876.101.2.77.27.1.5
fsMIBgp4mpeImportRouteNextHop NextHop Ipaddress for the route.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.27.1.6
fsMIBgp4mpeImportRouteIfIndex Interface Index of the Route	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.10876.101.2.77.27.1.7
fsMIBgp4mpeImportRouteMetric Metric for the route being imported.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.10876.101.2.77.27.1.8
fsMIBgp4mpeImportRouteVrf Vrf in which the route should be imported. If the rotueis to be installed in default VRF, the value should be NULL string	OctetString Constraints: range: 0-16	.1.3.6.1.4.1.10876.101.2.77.27.1.9
fsMIBgp4mpeImportRouteAction Controls addition or deletion of route.	Enumerationr/w Enumerated Values: 1 add 2 delete	.1.3.6.1.4.1.10876.101.2.77.27.1.10

Gets FSM transitions history per peer

fsMIBgp4MpeFsmTransitionHistEntry row .1.3.6.1.4.1.10876.101.2.77.28.1

Fsm Hist entry.

Indexes

fsMIBgp4ContextId fsMIBgp4mpePeerType fsMIBgp4mpePeer

Column	Syntax	OID
fsMIBgp4mpePeerType Type of Peer from which FSM transition history would be read.	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.28.1.1
fsMIBgp4mpePeer Peer from which FSM transition history would be read.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.28.1.2
fsMIBgp4mpeFsmTransitionHist sequence of FSM states separated by space	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.10876.101.2.77.28.1.3

Route damping history table.This table contains the figure-of-merit and 
the route status

fsMIBgp4MpeRfdRtDampHistEntry row .1.3.6.1.4.1.10876.101.2.77.29.1.1

Entry contains route damping history

Indexes

fsMIBgp4ContextId fsMIBgp4mpePathAttrAddrPrefixAfi fsMIBgp4mpePathAttrAddrPrefixSafi fsMIBgp4mpePathAttrAddrPrefix fsMIBgp4mpePathAttrAddrPrefixLen fsMIBgp4mpePathAttrPeerType fsMIBgp4mpePathAttrPeer

Column	Syntax	OID
fsMIBgp4mpePathAttrAddrPrefixAfi AFI of the route	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.29.1.1.1
fsMIBgp4mpePathAttrAddrPrefixSafi SAFI of the route	SUPERMICRO-BGP-MIBBgpSafi Type Values: 0 unknown 1 unicast 4 labelledIpv4 128 vpnv4	.1.3.6.1.4.1.10876.101.2.77.29.1.1.2
fsMIBgp4mpePathAttrAddrPrefix An IP address prefix in the NLRI field. This object is an IP address containing the prefix with the length specified by fsMIBgp4mpePathAttrAddrPrefixLen. Any bits beyond the length specified by bgp4PathAttrAddrPrefixL…	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.29.1.1.3
fsMIBgp4mpePathAttrAddrPrefixLen Length in bits of the IP address prefix in NLRI field.	Integer32 Constraints: range: 0-32	.1.3.6.1.4.1.10876.101.2.77.29.1.1.4
fsMIBgp4mpePathAttrPeerType AFI of the peer	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.29.1.1.5
fsMIBgp4mpePathAttrPeer The Peer remote address of the peer where the path information was learned.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.29.1.1.6
fsMIBgp4mpeRfdRtFom The figure-of-merit of the route	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.2.77.29.1.1.7
fsMIBgp4mpeRfdRtLastUpdtTime The time when the route figure-of-merit was updated.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.10876.101.2.77.29.1.1.8
fsMIBgp4mpeRfdRtState The value gives the status whether the route is suppressed or not	Enumeration Enumerated Values: 1 none 2 suppressed 3 unsuppressed	.1.3.6.1.4.1.10876.101.2.77.29.1.1.9
fsMIBgp4mpeRfdRtStatus The value gives the status whether the route is feasible or unfeasible route	Enumeration Enumerated Values: 1 none 2 feasibleroute 3 unfeasibleroute	.1.3.6.1.4.1.10876.101.2.77.29.1.1.10
fsMIBgp4mpeRfdRtFlapCount This value gives the number of times the route being flapped	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.2.77.29.1.1.11
fsMIBgp4mpeRfdRtFlapTime The time calculated for a route, from when a route is being flapped for first time, time in seconds	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.10876.101.2.77.29.1.1.12
fsMIBgp4mpeRfdRtReuseTime The time after which a route can be reused again after it moves to suppressed state from unsuppressed state, time in seconds	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.10876.101.2.77.29.1.1.13

Peer Damping history table. It contains the peer figure-of-merit and 
peer status.

fsMIBgp4MpeRfdPeerDampHistEntry row .1.3.6.1.4.1.10876.101.2.77.29.2.1

Entry contains peer damping history

Indexes

fsMIBgp4ContextId fsMIBgp4mpePeerRemoteIpAddrType fsMIBgp4mpePeerRemoteIpAddr

Column	Syntax	OID
fsMIBgp4mpePeerRemoteIpAddrType AFI of the remote peer	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.29.2.1.1
fsMIBgp4mpePeerRemoteIpAddr The peer remote address of the peer.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.29.2.1.2
fsMIBgp4mpeRfdPeerFom The current figure-of-merit of peer	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.2.77.29.2.1.3
fsMIBgp4mpeRfdPeerLastUpdtTime The time when the figure-of-merit was updated.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.10876.101.2.77.29.2.1.4
fsMIBgp4mpeRfdPeerState This value gives the status whether peer is suppressed or not	Enumeration Enumerated Values: 1 none 2 suppressed 3 unsuppressed	.1.3.6.1.4.1.10876.101.2.77.29.2.1.5
fsMIBgp4mpeRfdPeerStatus This value gives the status whether peer is up or down	Enumeration Enumerated Values: 1 none 2 peerup 3 peerdown	.1.3.6.1.4.1.10876.101.2.77.29.2.1.6

Routes Reuse List Table. It contains the IP prefix and prefix length.

fsMIBgp4MpeRfdRtsReuseListEntry row .1.3.6.1.4.1.10876.101.2.77.29.3.1

Entry contains routes reuse list

Indexes

fsMIBgp4ContextId fsMIBgp4mpeRtAfi fsMIBgp4mpeRtSafi fsMIBgp4mpeRtIPPrefix fsMIBgp4mpeRtIPPrefixLen fsMIBgp4mpeRfdRtsReusePeerType fsMIBgp4mpePeerRemAddress

Column	Syntax	OID
fsMIBgp4mpeRtAfi AFI of the route	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.29.3.1.1
fsMIBgp4mpeRtSafi AFI of the route	SUPERMICRO-BGP-MIBBgpSafi Type Values: 0 unknown 1 unicast 4 labelledIpv4 128 vpnv4	.1.3.6.1.4.1.10876.101.2.77.29.3.1.2
fsMIBgp4mpeRtIPPrefix An IP address prefix in the NLRI field. This object is an IP address containing the prefix with the length specified by fsMIBgp4RtIPPrefixLen. Any bits beyond the length specified by fsMIBgp4IPPrefixLen are zeroed.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.29.3.1.3
fsMIBgp4mpeRtIPPrefixLen Length in bits of the IP address prefix in NLRI field.	Integer32 Constraints: range: 0-32	.1.3.6.1.4.1.10876.101.2.77.29.3.1.4
fsMIBgp4mpeRfdRtsReusePeerType AFI of the remote peer	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.29.3.1.5
fsMIBgp4mpePeerRemAddress The Peer remote address of the peer where the path information was learned.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.29.3.1.6
fsMIBgp4mpeRfdRtReuseListRtFom The figure-of-merit of the route which is in the routes reuse list	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.2.77.29.3.1.7
fsMIBgp4mpeRfdRtReuseListRtLastUpdtTime The time when the route figure-of-merit was updated.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.10876.101.2.77.29.3.1.8
fsMIBgp4mpeRfdRtReuseListRtState The value gives the status whether the route is suppressed or not	Enumeration Enumerated Values: 1 none 2 suppressed 3 unsuppressed	.1.3.6.1.4.1.10876.101.2.77.29.3.1.9
fsMIBgp4mpeRfdRtReuseListRtStatus The value gives the status whether the route is feasible or unfeasible route	Enumeration Enumerated Values: 1 none 2 feasibleroute 3 unfeasibleroute	.1.3.6.1.4.1.10876.101.2.77.29.3.1.10

Peer's Reuse List Table. It contains the Peer Remote Address.

fsMIBgp4MpeRfdPeerReuseListEntry row .1.3.6.1.4.1.10876.101.2.77.29.4.1

Entry contains routes reuse list

Indexes

fsMIBgp4ContextId fsMIBgp4mpeRfdPeerRemIpAddrType fsMIBgp4mpeRfdPeerRemIpAddr

Column	Syntax	OID
fsMIBgp4mpeRfdPeerRemIpAddrType AFI of the peer	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.29.4.1.1
fsMIBgp4mpeRfdPeerRemIpAddr The peer remote address of the peer which is in the peer's reuse list.	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.29.4.1.2
fsMIBgp4mpeRfdPeerReuseListPeerFom The current figure-of-merit of peer	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.10876.101.2.77.29.4.1.3
fsMIBgp4mpeRfdPeerReuseListLastUpdtTime The time when the figure-of-merit was updated.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.10876.101.2.77.29.4.1.4
fsMIBgp4mpeRfdPeerReuseListPeerState This value gives the status whether peer is suppressed or not	Enumeration Enumerated Values: 1 none 2 suppressed 3 unsuppressed	.1.3.6.1.4.1.10876.101.2.77.29.4.1.5
fsMIBgp4mpeRfdPeerReuseListPeerStatus This value gives the status whether peer is up or down	Enumeration Enumerated Values: 1 none 2 peerup 3 peerdown	.1.3.6.1.4.1.10876.101.2.77.29.4.1.6

This table is used to configure additive communities
for a given destination.

fsMIBgp4MpeCommRouteAddCommEntry row .1.3.6.1.4.1.10876.101.2.77.30.1.1

Routes configured additive communities Table Entry

Indexes

fsMIBgp4ContextId fsMIBgp4mpeAddCommRtAfi fsMIBgp4mpeAddCommRtSafi fsMIBgp4mpeAddCommIpNetwork fsMIBgp4mpeAddCommIpPrefixLen fsMIBgp4mpeAddCommVal

Column	Syntax	OID
fsMIBgp4mpeAddCommRtAfi AFI of IP address of the destination	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.30.1.1.1
fsMIBgp4mpeAddCommRtSafi SAFI of IP address of the destination	SUPERMICRO-BGP-MIBBgpSafi Type Values: 0 unknown 1 unicast 4 labelledIpv4 128 vpnv4	.1.3.6.1.4.1.10876.101.2.77.30.1.1.2
fsMIBgp4mpeAddCommIpNetwork IP address of the destination	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.30.1.1.3
fsMIBgp4mpeAddCommIpPrefixLen IP prefix length for the destination	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.10876.101.2.77.30.1.1.4
fsMIBgp4mpeAddCommVal Additive Community configured for the Route	Unsigned32 Constraints: range: 65536-4294901759 range: 4294967041-4294967043	.1.3.6.1.4.1.10876.101.2.77.30.1.1.5
fsMIBgp4mpeAddCommRowStatus Row status for creating entries into this table.This object can be set only if fsMIBgp4LocalAS is configured.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.2.77.30.1.1.6

This table is used to configure delete communities
for a given destination.

fsMIBgp4MpeCommRouteDeleteCommEntry row .1.3.6.1.4.1.10876.101.2.77.30.2.1

Routes configured delete communities Table Entry

Indexes

fsMIBgp4ContextId fsMIBgp4mpeDeleteCommRtAfi fsMIBgp4mpeDeleteCommRtSafi fsMIBgp4mpeDeleteCommIpNetwork fsMIBgp4mpeDeleteCommIpPrefixLen fsMIBgp4mpeDeleteCommVal

Column	Syntax	OID
fsMIBgp4mpeDeleteCommRtAfi AFI of IP address of the destination	SUPERMICRO-BGP-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.10876.101.2.77.30.2.1.1
fsMIBgp4mpeDeleteCommRtSafi SAFI of IP address of the destination	SUPERMICRO-BGP-MIBBgpSafi Type Values: 0 unknown 1 unicast 4 labelledIpv4 128 vpnv4	.1.3.6.1.4.1.10876.101.2.77.30.2.1.2
fsMIBgp4mpeDeleteCommIpNetwork IP address of the destination	SUPERMICRO-BGP-MIBInetAddress Type Constraints: range: 0..40	.1.3.6.1.4.1.10876.101.2.77.30.2.1.3
fsMIBgp4mpeDeleteCommIpPrefixLen IP prefix length for the destination	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.10876.101.2.77.30.2.1.4
fsMIBgp4mpeDeleteCommVal Delete Community configured for the Route	Unsigned32 Constraints: range: 65536-4294901759 range: 4294967041-4294967043	.1.3.6.1.4.1.10876.101.2.77.30.2.1.5
fsMIBgp4mpeDeleteCommRowStatus Row status for creating entries into this table.This object can be set only if fsMIBgp4LocalAS is configured.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.2.77.30.2.1.6