STAND-ALONE-ETHERNET-SWITCH-MIB Table View

A list of configuration entries for individually switched
ports.

swPortEntry row .1.3.6.1.4.1.437.1.1.3.3.1.1

Configuration parameters for an individually switched port.

Indexes

swPortIndex

Column	Syntax	OID
swPortIndexmandatory Number greater than zero identifying an individually switched port. The same value of a port index variable for any of the port tables in this MIB group selects the same port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.1.1.1
swPortControllerRevisionmandatory Returns the revision number of the port controller.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.1.1.2
swPortNamemandatory A descriptive string of up to 60 characters used by the network administrator to name a port.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-60	.1.3.6.1.4.1.437.1.1.3.3.1.1.3
swPortMediaCapabilitymandatory The port media capability is one of: other : none of the following private-ethernet : dedicated 10 Mbps Ethernet port general-ethernet : non-dedicated 10 Mbps Ethernet port general-fast-ethernet: non-dedicate…	Enumeration Enumerated Values: 1 other 2 private-ethernet 3 general-ethernet 4 general-fast-ethernet 5 private-fast-ethernet 6 repeated-fast-ethernet 7 fddi 8 atm	.1.3.6.1.4.1.437.1.1.3.3.1.1.4
swPortTypemandatory Identifies whether the port is other : none of the following network : port does not have address number restriction while it is unsecured. A secured Network port has an imposed limit on the m…	Enumeration Enumerated Values: 1 other 2 network	.1.3.6.1.4.1.437.1.1.3.3.1.1.5
swPortConnectorTypemandatory The type of connector the port is currently using. It is one of other : none of the following (unknown) rj45 : common unshielded twisted pair connector bnc : thin-coax (BNC) aui : thick-c…	Enumeration Enumerated Values: 1 other 2 rj45 3 bnc 4 aui 5 fiber-sc 6 fiber-st 7 empty 8 group 10 fddi-mic 11 fiber-mtrj	.1.3.6.1.4.1.437.1.1.3.3.1.1.6
swPortACRobsolete Selects whether Accelerated Congestion Resolution (ACR) should be used on the port. When enabled(1), ACR allows for early frame discard when congestion is experienced on a port, thus limiting the number of frames which…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.437.1.1.3.3.1.1.7
swPortFullDuplexmandatory Set to enabled(1) to operate in full duplex mode: port will allow simultaneous transmit and receive which can double its bandwidth. Set to disabled(2) to operate in normal mode. Set to auto-negotiate(3) to allow the swi…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled 3 auto-negotiate 4 enabled-flow-control	.1.3.6.1.4.1.437.1.1.3.3.1.1.8
swPortStatusmandatory Current operational status of the port. Possible values are: enabled : normal operation (transmit and receive) disabled-mgmt : disabled by explicit management action suspended-linkbeat : suspended…	Enumeration Enumerated Values: 1 enabled 2 disabled-mgmt 3 suspended-linkbeat 4 suspended-jabber 5 suspended-violation 7 disabled-violation 9 suspended-not-present 10 suspended-not-recognized 11 reset 12 suspended-ringdown 13 suspended-stp 14 disabled-self-test 15 enable-degraded 16 suspended-atm-lane-down 17 suspended-no-vlan 18 disabled-no-vlan 19 suspended-atm-network-down 20 suspended-disl	.1.3.6.1.4.1.437.1.1.3.3.1.1.9
swPortAdminStatusmandatory By explicit management action, change the port status to either enabled : normal status (transmit and receive enabled) disabled-mgmt: transmit and receive disabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled-mgmt	.1.3.6.1.4.1.437.1.1.3.3.1.1.10
swPortLastStatusmandatory The value of swPortStatus prior to its current value.	Enumeration Enumerated Values: 1 enabled 2 disabled-mgmt 3 suspended-linkbeat 4 suspended-jabber 5 suspended-violation 7 disabled-violation 9 suspended-not-present 10 suspended-not-recognized 11 reset 12 suspended-ringdown 13 suspended-stp 14 disabled-self-test 15 enable-degraded 16 suspended-atm-lane-down 17 suspended-no-vlan 18 disabled-no-vlan 19 suspended-atm-network-down 20 suspended-disl	.1.3.6.1.4.1.437.1.1.3.3.1.1.11
swPortStatusChangesmandatory Number of times swPortStatus has changed.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.1.1.12
swPortAddressingSecuritymandatory Set to enabled(1) to effect addressing security. Set to disabled(2) to leave the port unsecure Addressing security cannot be enabled on a port whose type is Network and doing so will result in badValue.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.437.1.1.3.3.1.1.13
swPortAddressTableSizemandatory For secured Network port, the address table size can range from 1 to 132. For unsecured Network port, the size is unrestricted (shown as the value zero) and is, therefore, not settable. Any attempt to violate these ru…	Integer32r/w Constraints: range: 0-132	.1.3.6.1.4.1.437.1.1.3.3.1.1.14
swPortNumberOfLearnedAddressesmandatory The current number of dynamically learned addresses on the port. The initial value is zero.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.1.1.15
swPortNumberOfStaticAddressesmandatory The current number of statically assigned unicast addresses on the port. The initial value is zero.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.1.1.16
swPortEraseAddressesmandatory Set to erase(2) to delete all learned and assigned static unicast addresses the port currently has. Setting the object to noErase(1) has no effect. This object always returns noErase(1) when read.	Enumerationr/w Enumerated Values: 1 noErase 2 erase	.1.3.6.1.4.1.437.1.1.3.3.1.1.17
swPortFloodUnregisteredMulticastsmandatory Set to enabled(1) to allow the forwarding to this port frames addressed to multicast addresses that have not been registered for the port. Set to disabled(2) to filter and discard such frames. The default value is ena…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.437.1.1.3.3.1.1.18
swPortFloodUnknownUnicastsmandatory This object controls the forwarding of unknown unicast frames to this port. When set to enabled(1) the switch, upon receiving a frame with an unknown unicast destination address on another port, will tran…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.437.1.1.3.3.1.1.19
swPortMonitoringmandatory Set to enabled(1) to forward receive and transmit frames on this port to the port identified by sysConfigMonitorPort. Set to disabled(2) to not monitor frame traffic on this port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.437.1.1.3.3.1.1.20
swPortSecuredAddressViolationsmandatory Number of times a source address was seen on this port which duplicates a secured address configured on another port, plus the number of times a source address was seen on this port which does not match any addresses se…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.1.1.21
swPortLinkbeatStatusmandatory The current port linkbeat status.	Enumeration Enumerated Values: 1 linkbeat 2 noLinkbeat	.1.3.6.1.4.1.437.1.1.3.3.1.1.22
swPortLinkbeatLossesmandatory Number of times that the value of swPortLinkbeatStatus has changed from linkbeat to noLinkbeat.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.1.1.23
swPortJabberStatusmandatory The current jabber function result.	Enumeration Enumerated Values: 1 notJabbering 2 jabbering	.1.3.6.1.4.1.437.1.1.3.3.1.1.24
swPortJabbersmandatory Number of times that the jabber function has to be invoked because a frame transmitted from this port exceeded a certain time duration.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.1.1.25
swPortClearStatisticsmandatory Set to clear(2) to zero out all statistics associated with the port. Per-port statistics are kept in this swPortTable as well as in the swPortRxStatTable, swPortTxStatTable, swPortTxCollTable, dot1dBasePortTable, and d…	Enumerationr/w Enumerated Values: 1 noClear 2 clear	.1.3.6.1.4.1.437.1.1.3.3.1.1.26
swPortBroadcastStormBlockedmandatory The current broadcast forwarding status of this port. If this port is blocked by broadcast storm control, the switch drops all broadcasts received from the port.	Enumeration Enumerated Values: 1 notBlocked 2 blocked	.1.3.6.1.4.1.437.1.1.3.3.1.1.27
swPortSTPPortFastModemandatory This object configures the port into the Spanning Tree port-fast mode. When enabled(1), the STP can transition the port's state directly from blocking to forwarding, and vice versa, without going through the intermediat…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.437.1.1.3.3.1.1.28
swPortHalfDuplexBackPressureobsolete Back pressure allows a port to force a collision when there is no buffer to receive frames. The port must be in half duplex to benefit from this enhancement. If the port is operating to be in full duplex, back pressure …	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.437.1.1.3.3.1.1.29
swPortDuplexStatusmandatory The status of duplex mode on this port. This shows the result of full duplex auto-negotiation when swPortFullDuplex is set to auto-negotiate.	Enumeration Enumerated Values: 1 full-duplex 2 half-duplex 3 full-duplex-flow-control	.1.3.6.1.4.1.437.1.1.3.3.1.1.30
swPortFullDuplexFlowControlobsolete The configuration of flow control on this port. Flow control allows the port to throttle packet transmission according to flow control messages sent by the other end of the link. For ports that do not sup…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.437.1.1.3.3.1.1.31
swPortEnhancedCongestionControlmandatory Enhanced Congestion Control (ECC) reduces the transmit back-off period to allow the port to transmit more quickly, thereby reducing the transmit queue congestion on the port. When set to disabled(2), ECC is disabled. Wh…	Enumerationr/w Enumerated Values: 1 adaptive 2 disabled 3 moderate-aggressive 4 aggressive	.1.3.6.1.4.1.437.1.1.3.3.1.1.32
swPortBridgePrioritymandatory This is the bridge port priority. When a port is a non-trunk, the value of this object is the same as dot1dStpPortPriority in RFC 1493 for the port. When a port is operating as a VLAN trunk…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.1.1.33
swPortBridgePriorityAlternatemandatory This object specifies the other priority that can be used as the port priority for each instance of spanning tree operating on a trunk port. See the definition for swPortBridgePriority.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.1.1.34
swPortBridgePathCostmandatory This is the bridge port path cost. When a port is a non-trunk, the object's value is the same as dot1dStpPortPathCost in RFC 1493 for the port. When a port is operating as a VLAN trunk, the…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.1.1.35
swPortBridgePathCostAlternatemandatory This object specifies the other path cost that can be used as the port path cost for each instance of spanning tree operating on a trunk port. The value of this object must be less than or equal to the value of swPort…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.1.1.36
swPortIfIndexmandatory This is the value of MIB-II ifIndex object corresponding to this port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.1.1.37
swPortInternalmandatory This indicates if the port is an internal port. An internal port is one that does not allow a direct physical connection to another device. An example of an internal port is a switched port of a slot with a repeater mod…	Enumeration Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.437.1.1.3.3.1.1.38

A list of switch port Receive statistics entries.

swPortRxStatEntry row .1.3.6.1.4.1.437.1.1.3.3.2.1

Receive statistics for an individually switched port.

Indexes

swPortRxStatIndex

Column	Syntax	OID
swPortRxStatIndexmandatory A number greater than zero identifying an individually switched port. The same value of a port index variable for any of the port tables in this MIB group selects the same port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.2.1.1
swPortRxTotalFramesmandatory A count of all frames that are successfully received. This does not include frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to internal MAC sublayer error.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.2
swPortRxTotalOctetsmandatory A count of data and padding octets in all octets that are successfully received. This does not include octets in frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to internal MAC …	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.3
swPortRxTotalOctetsWrapsmandatory The number of times the value in swPortRxTotalOctets has rolled to zero.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.4
swPortRxUnicastFramesmandatory A count of frames that are successfully received and are directed to a unicast address. This does not include frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to internal MAC sub…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.5
swPortRxUnicastOctetsmandatory A count of data and padding octets in unicast frames that are successfully received. This does not include octets in frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to internal …	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.6
swPortRxUnicastOctetsWrapsmandatory The number of times the value in swPortRxUnicastOctets has rolled to zero.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.7
swPortRxBroadcastFramesmandatory A count of frames that are successfully received and are directed to the broadcast address. This does not include frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to internal MAC…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.8
swPortRxBroadcastOctetsmandatory A count of data and padding octets in broadcast frames that are successfully received. This does not include octets in frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to interna…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.9
swPortRxBroadcastOctetsWrapsmandatory The number of times the value in swPortRxBroadcastOctets has rolled to zero.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.10
swPortRxMulticastFramesmandatory A count of frames that are successfully received and are directed to a multicast address. This does not include frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to internal MAC s…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.11
swPortRxMulticastOctetsmandatory A count of data and padding octets in multicast frames that are successfully received. This does not include octets in frames received with frame-too-long, FCS, length or alignment errors, or frames lost due to interna…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.12
swPortRxMulticastOctetsWrapsmandatory The number of times the value in swPortRxMulticastOctets has rolled to zero.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.13
swPortRxForwardedFramesmandatory Count of frames received and forwarded to some other port(s) for transmission.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.14
swPortRxFilteredFramesmandatory A count of frames received that were discarded because 1) the frames were local to the segment, 2) no destination address matches could be found and no ports were set up to accept such frames, 3) the destination address…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.15
swPortRxNoBufferDiscardsmandatory A count of frames received that were discarded due to a lack of frame buffer resources in the switch's forwarding engine.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.16
swPortRxFCSErrorsmandatory A count of frames received that are an integral number of octets in length but do not pass the Frame Check Sequence test.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.17
swPortRxAlignmentErrorsmandatory A count of frames received that are not an integral number of octets in length and do not pass the Frame Check Sequence test.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.18
swPortRxFrameTooLongsmandatory A count of frames received that exceed the maximum permitted frame size as defined by the corresponding portMtu object.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.19
swPortRxRuntsmandatory A count of frames received that are shorter than the minimum permitted frame size. Runts usually indicate collision fragments, a normal network event.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.2.1.20

A list of switch port Transmit statistics entries.

swPortTxStatEntry row .1.3.6.1.4.1.437.1.1.3.3.3.1

Transmit statistics for an individually switched port.

Indexes

swPortTxStatIndex

Column	Syntax	OID
swPortTxStatIndexmandatory A number greater than zero identifying an individually switched port. The same value of a port index variable for any of the port table in this MIB group selects the same port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.3.1.1
swPortTxTotalFramesmandatory A count of all frames that are successfully transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.2
swPortTxTotalOctetsmandatory A count of data and padding octets in all frames that are successfully transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.3
swPortTxTotalOctetsWrapsmandatory The number of times the value in swPortTxTotalOctets has rolled to zero.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.4
swPortTxUnicastFramesmandatory A count of frames that are successfully transmitted and are directed to a unicast address.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.5
swPortTxUnicastOctetsmandatory A count of data and padding octets in unicast frames that are successfully transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.6
swPortTxUnicastOctetsWrapsmandatory The number of times the value in swPortTxUnicastOctets has rolled to zero.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.7
swPortTxBroadcastFramesmandatory A count of frames that are successfully transmitted and are directed to the broadcast address.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.8
swPortTxBroadcastOctetsmandatory A count of data and padding octets in broadcast frames that are successfully transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.9
swPortTxBroadcastOctetsWrapsmandatory The number of times the value in swPortTxBroadcastOctets has rolled to zero.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.10
swPortTxMulticastFramesmandatory A count of frames that are successfully transmitted and are directed to a multicast address.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.11
swPortTxMulticastOctetsmandatory A count of data and padding octets in multicast frames that are successfully transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.12
swPortTxMulticastOctetsWrapsmandatory The number of times the value in swPortTxMulticastOctets has rolled to zero.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.13
swPortTxDeferralsmandatory A count of frames for which the first transmission attempt is delayed because the medium is busy.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.14
swPortTxSingleCollisionsmandatory A count of successfully transmitted frames for which transmission is inhibited by exactly one collision.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.15
swPortTxMultipleCollisionsmandatory A count of successfully transmitted frames for which transmission is inhibited by more than one collision.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.16
swPortTxLateCollisionsmandatory The number of times that a collision is detected later than 512 bit-times into the transmission of a frame. A late collision is also considered as a (generic) collision for purposes of other collision-related statistic…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.17
swPortTxExcessiveCollisionsmandatory A count of frames for which transmission fails due to excessive collisions. The threshold is either 16 in the normal mode of operation, or 4 in the Enhanced Congestion Control (ECC) mode. Thus, this count is the sum o…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.18
swPortTxExcessiveDeferralsmandatory A count of frames for which transmission is deferred for an excessive period of time.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.19
swPortTxExcessiveCollision16smandatory A count of frames that due to excessive collisions are not transmitted successfully. Here, the normal threshold of 16 collisions is used to determine the status of the transmission. A swPortTxExcessiveCollision16s is …	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.20
swPortTxExcessiveCollision4smandatory A count of frames that due to excessive collisions are not transmitted successfully. Here, the Enhanced Congestion Control threshold of 4 collisions is used to determine the status of the transmission. A swPortTxExces…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.21
swPortTxQueueFullDiscardsmandatory A count of frames that cannot be transmitted because the transmit queue for the port is full.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.22
swPortTxErrorsmandatory A count of frames for which transmission fails due to an internal MAC sublayer transmit error. A frame is only counted by an instance of this object if it is not counted by the corresponding instance of either the swPo…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.3.1.23

A collection of collision histograms for the switch ports.

swPortTxCollEntry row .1.3.6.1.4.1.437.1.1.3.3.4.1

This table provides a per port histogram of collision
activity. The swPortTxCollIndex index (1 to
sysInfoNumberOfSwitchPorts) identifies an individually
switched port, and the swPortTxCollCount index (1 to 16)
denotes …

Indexes

swPortTxCollIndex swPortTxCollCount

Column	Syntax	OID
swPortTxCollIndexmandatory A number greater than zero identifying an individually switched port. The same value of a port index variable for any of the port tables in this MIB group selects the same port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.3.4.1.1
swPortTxCollCountmandatory The number of per-frame media collisions for which a particular collision histogram cell represents the frequency on a particular port.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.437.1.1.3.3.4.1.2
swPortTxCollFrequenciesmandatory A count of frames for which the transmission (successful or otherwise) on a particular port is accompanied by a particular number of media collisions.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.437.1.1.3.3.4.1.3

Table (4 entries) containing a list of IP addresses or DNS
name of workstations permitted to issue SET requests.  Such a
workstation is called a Set client.  If this table is
empty then any SET request with a matching SET community
string is allowed.  If at least one Set client is specified,
then an incoming SET request must have its source IP
address or name matched against an entry in this table before the
SET is allowed.
          
An Set client entry whose IP address is 0.0.0.0 is considered
invalid and will be ignored.
          
This table is considered empty when all Set client
addresses are zeroes (0.0.0.0). and DNS names are empty

netMgmtSetClientEntry row .1.3.6.1.4.1.437.1.1.3.4.13.1

An IP address of a manager station allowed to issue
SET requests to this management agent.

Indexes

netMgmtSetClientIndex

Column	Syntax	OID
netMgmtSetClientIndexmandatory Identification of a SET client entry.	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.437.1.1.3.4.13.1.1
netMgmtSetClientAddrmandatory The SET client is assumed to be Internet UDP/IP based. And this is the client's IP address. Setting this object will cause the value in the corresponding netMgmtSetClientName object to cleared.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.437.1.1.3.4.13.1.2
netMgmtSetClientStatusmandatory Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the IP address identified with said entry from the table. It is an implementati…	Enumerationr/w Enumerated Values: 1 other 2 invalid 3 permanent	.1.3.6.1.4.1.437.1.1.3.4.13.1.3
netMgmtSetClientNamemandatory The Set Client's DNS host name. The switch will resolve the host name to IP address via DNS and copy the resolved IP address into netMgmtSetClientAddr object. Therefore the value of this object overwrites any value in n…	RFC1213-MIBDisplayStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.437.1.1.3.4.13.1.4

Table (4 entries) containing a list of Network Management
Stations that are to receive traps generated by this
Network Management Agent.  Such an NMS is called a
Trap client.
          
An Trap client entry whose IP address is 0.0.0.0 and DNS name
is empty is considered invalid and will be ignored.

netMgmtTrapClientEntry row .1.3.6.1.4.1.437.1.1.3.4.14.1

A destination address and community string to a particular
trap client.

Indexes

netMgmtTrapClientIndex

Column	Syntax	OID
netMgmtTrapClientIndexmandatory Identification of a trap client entry.	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.437.1.1.3.4.14.1.1
netMgmtTrapClientAddrmandatory The trap client is assumed to be Internet UDP/IP based. And this is the client's IP address. Setting a value for this object will cause the value of netMgmtTrapClientName to be cleared (set to null string).	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.437.1.1.3.4.14.1.2
netMgmtTrapClientCommmandatory Community string used for traps sent to this trap client.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.437.1.1.3.4.14.1.3
netMgmtTrapClientStatusmandatory Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the IP address/community string identified with said entry from the table. It i…	Enumerationr/w Enumerated Values: 1 other 2 invalid 3 permanent	.1.3.6.1.4.1.437.1.1.3.4.14.1.4
netMgmtTrapClientNamemandatory The Trap Client's DNS host name. The switch will resolve the host name to an IP address via DNS and copy the resolved IP address into netMgmtTrapClientAddr object. If netMgmtTrapClientAddr is set the value of this objec…	RFC1213-MIBDisplayStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.437.1.1.3.4.14.1.5

A list of configuration entries for a VLAN.

vlanEntry row .1.3.6.1.4.1.437.1.1.3.6.3.1

Configuration parameters for a VLAN.

Indexes

vlanIndex

Column	Syntax	OID
vlanIndexmandatory Number from 1 to vlanMaxSupported identifying a configurable VLAN.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.6.3.1.1
vlanNamemandatory A descriptive string of up to 60 characters used by the network administrator to name a VLAN. This object is not supported by switches operating with firmware version greater than or equal to 6.00	RFC1213-MIBDisplayStringr/w Constraints: range: 0-60	.1.3.6.1.4.1.437.1.1.3.6.3.1.2
vlanMemberPortsmandatory The set of the switch's member ports for the VLAN. A port may reside within multiple VLANs only if the object vlanAllowMembershipOverlap has been set to enabled. This object cannot be used to configure VL…	OctetString	.1.3.6.1.4.1.437.1.1.3.6.3.1.3
vlanIpAddressmandatory The switch's administrative IP address in this VLAN. Note that once a value has been set for this object, the next write will only take effect after a system reset. The default value is the same as the address contained…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.437.1.1.3.6.3.1.4
vlanIpSubnetMaskmandatory The switch's administrative IP subnet mask in this VLAN. A change in the subnet mask at any time will immediately take effect. The default value is the same as the mask contained in netMgmtIpSubnetMask. …	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.437.1.1.3.6.3.1.5
vlanBridgeTemplatemandatory The bridge parameter template used by the VLAN. By default, a VLAN uses template 1. The value of this object must be one of the values of bridgeTemplateIndex. This object is supported only by switches ope…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.6.3.1.6
vlanStpAdminmandatory This object indicates if STP is enabled or disabled for the VLAN. This object is supported only by switches operating with firmware version greater than or equal to 7.00	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.437.1.1.3.6.3.1.7

A list of port membership configuration entries for a VLAN.

vlanMemberEntry row .1.3.6.1.4.1.437.1.1.3.6.4.1

Port membership configuration parameters for a VLAN.

Indexes

vlanMemberIndex vlanMemberPortIndex

Column	Syntax	OID
vlanMemberIndexmandatory Number from 1 to vlanMaxSupported identifying a configurable VLAN. The same value of a VLAN index variable for any of the VLAN tables in this MIB group selects the same VLAN.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.6.4.1.1
vlanMemberPortIndexmandatory Number greater than zero identifying an individually switched port. The same value of a port index variable for any of the port tables selects the same port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.6.4.1.2
vlanMemberPortOfVlanmandatory The port identified by vlanMemberPortIndex becomes a member of the VLAN identified by vlanMemberIndex when this object is set to true(1). The same port ceases to be member of that VLAN when the object is set to false(2…	Enumerationr/w Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.437.1.1.3.6.4.1.3

A list of bridge configuration templates.

bridgeTemplateEntry row .1.3.6.1.4.1.437.1.1.3.6.6.1

Configuration parameters for a bridge parameter template.

Indexes

bridgeTemplateIndex

Column	Syntax	OID
bridgeTemplateIndexmandatory Number from 1 to bridgeTemplateMax identifying a configurable bridge parameters template.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.6.6.1.1
bridgeTemplatePrioritymandatory See dot1dStpPriority in RFC 1493. The value of dot1dStpPriority must match the value of an instance of this object.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.6.6.1.2
bridgeTemplateMaxAgemandatory See dot1dStpBridgeMaxAge in RFC 1493. The value of dot1dStpBridgeMaxAge must match the value of an instance of this object.	BRIDGE-MIBTimeoutr/w	.1.3.6.1.4.1.437.1.1.3.6.6.1.3
bridgeTemplateHelloTimemandatory See dot1dStpBridgeHelloTime in RFC 1493. The value of dot1dStpBridgeHelloTime must match the value of an instance of this object.	BRIDGE-MIBTimeoutr/w	.1.3.6.1.4.1.437.1.1.3.6.6.1.4
bridgeTemplateForwardDelaymandatory See dot1dStpBridgeForwardDelay in RFC 1493. The value of dot1dStpBridgeForwardDelay must match the value of an instance of this object.	BRIDGE-MIBTimeoutr/w	.1.3.6.1.4.1.437.1.1.3.6.6.1.5

A list of entries containing peak bandwidth usages in
a number of time periods.

bandwidthUsagePeakEntry row .1.3.6.1.4.1.437.1.1.3.7.6.1

Information about peak bandwidth usage in a time period.

Indexes

bandwidthUsagePeakIndex

Column	Syntax	OID
bandwidthUsagePeakIndexmandatory Number from 1 to bandwidthUsageMaxPeakEntries identifying a particular bandwithUsagePeakEntry.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.7.6.1.1
bandwidthUsageStartTimemandatory Up to 32 characters containing the date and time that marks the start of this capture interval. The string is in net ASCII and conforms exactly to the following format: Mon Sep 21 07:00:00 1992	RFC1213-MIBDisplayString Constraints: range: 0-32	.1.3.6.1.4.1.437.1.1.3.7.6.1.2
bandwidthUsagePeakmandatory The highest bandwidth utilized since the time given in bandwidthUsageStartTime or last cleared. The measurement unit is in megabits per second (1,000,000 bits/second).	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.7.6.1.3
bandwidthUsagePeakTimemandatory Up to 32 characters containing the date and time the value in bandwidthUsagePeak is captured. The string is in net ASCII and conforms exactly to the following format: Mon Sep 21 07:02:01 1992	RFC1213-MIBDisplayString Constraints: range: 0-32	.1.3.6.1.4.1.437.1.1.3.7.6.1.4

A list of configuration entries for a bridge group.

bridgeGroupEntry row .1.3.6.1.4.1.437.1.1.3.8.3.1

Configuration parameters for a bridge group.

Indexes

bridgeGroupIndex

Column	Syntax	OID
bridgeGroupIndexmandatory Number from 1 to bridgeGroupMaxSupported identifying a configurable bridge group.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.8.3.1.1
bridgeGroupMemberPortsmandatory The set of the switch's member ports for the bridge group. A port may reside within multiple bridge groups only if the object bridgeGroupAllowMembershipOverlap has been set to enabled(1). This object cann…	OctetString	.1.3.6.1.4.1.437.1.1.3.8.3.1.3
bridgeGroupStpAdminmandatory This object indicates if STP is enabled or disabled for the bridge group. The default is enabled(1).	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.437.1.1.3.8.3.1.4

A list of port membership configuration entries for a
bridge group.

bridgeGroupMemberEntry row .1.3.6.1.4.1.437.1.1.3.8.4.1

Port membership configuration parameters for a bridge group.

Indexes

bridgeGroupMemberIndex bridgeGroupMemberPortIndex

Column	Syntax	OID
bridgeGroupMemberIndexmandatory The value of bridgeGroupIndex of a bridge group.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.8.4.1.1
bridgeGroupMemberPortIndexmandatory The value of swPortIndex of a switched port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.437.1.1.3.8.4.1.2
bridgeGroupMemberPortOfBridgeGroupmandatory The port identified by bridgeGroupMemberPortIndex becomes a member of the bridgeGroup identified by bridgeGroupMemberIndex when this object is set to true(1). The same port ceases to be member of that bridgeGroup when …	Enumerationr/w Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.437.1.1.3.8.4.1.3