SCTE-HMS-HE-OPTICAL-SWITCH-MIB Table View

A table containing information about Optical Switch used
in an indoor environment.

heOpSwitchUnitEntry row .1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1

List of information about each optical switch.

Indexes

ENTITY-MIBentPhysicalIndex

Column	Syntax	OID
heOpSwitchMode This controls and/or reports the switching mode. If automatic(1), the optical switch will evaluate the optical input status and make the decision to affect the switch state. If set to manual(2), the optical switch …	Enumerationr/w Enumerated Values: 1 automatic 2 manual	.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.1
heOpSwitchControl Sets the intended state of the Optical Switch. The effect of this control will depend on the value of heOpSwitchMode. If heOpSwitchMode is set to automatic, the value this control is set to will be the preferred setti…	Enumerationr/w Enumerated Values: 1 pathA 2 pathB 3 cross 4 bar 5 bothA 6 bothB	.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.2
heOpSwitchRevertEnable This controls the use of revertive switching. If set to on, the switch will attempt to go back to the preferred settings indicated by heOpSwitchControl if heOpSwitchMode is set to automatic, and the i…	SCTE-HMS-HEADENDIDENT-MIBHeOnOffControlr/w Type Values: 1 off 2 on 3 meaningless	.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.3
heOpSwitchState Reports the state of the Optical Switch. Not all enumerations must be supported. For example, an A-B optical switch may support only the pathA and pathB enumerations while a cross-bar switch may support cross, bar,…	Enumeration Enumerated Values: 1 pathA 2 pathB 3 cross 4 bar 5 bothA 6 bothB	.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.4
heOpSwitchFailoverStatus The integral status of both inputs. A value is fault(2), if current switch state heOpSwitchState is different than the preferred setting heOpSwitchControl, otherwise, it is normal(1). …	SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus Type Values: 1 normal 2 fault	.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.5
heOpSwitchBothInputStatus The integral status of both inputs. A value is fault(2), if both input levels are below the nominal value; otherwise, it is normal(1). This object must provide for the alarm management cap…	SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus Type Values: 1 normal 2 fault	.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.6
heOpSwitchSelectWavelength Wavelength feeding the particular input of the optical switch. Typical values might be 131000 (1310 nm) and 155000 (1550 nm).	0.01 nmSCTE-HMS-HEADENDIDENT-MIBHeHundredthNanoMeterr/w	.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.7
heOpSwitchHysteresis Controls switch input hysteresis amount. The amount of hysteresis used and the ability to change it is to be determined by the vendor.	0.1 dBInteger32r/w Constraints: range: -20-20	.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.8
heOpSwitchWaitToRestoreTime Controls hysteresis time in sec. If in automatic switching mode and revert mode is enabled, a switch back to the original side will be delayed for the time specified by this object.	1 secSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.9

A table containing information about each Optical Switch 
input used in an indoor environment.

heOpSwitchInputEntry row .1.3.6.1.4.1.5591.1.11.1.4.1.1.2.1

List of information about each optical switch input.

Indexes

ENTITY-MIBentPhysicalIndex heOpSwitchInputIndex

Column	Syntax	OID
heOpSwitchInputIndex Index number corresponding to the Optical Input.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5591.1.11.1.4.1.1.2.1.1
heOpSwitchInputOpticalLevel The measured optical input power for the optical switch.	0.1 dBmSCTE-HMS-HEADENDIDENT-MIBHeTenthdBm	.1.3.6.1.4.1.5591.1.11.1.4.1.1.2.1.2
heOpSwitchSetInputPowerThreshold Input power switchover point for this input.	0.1 dBmSCTE-HMS-HEADENDIDENT-MIBHeTenthdBmr/w	.1.3.6.1.4.1.5591.1.11.1.4.1.1.2.1.3
heOpSwitchInputStatus The integral status of the input. A value is fault(2), if the input levels are not in the nominal range; otherwise, it is normal(1). This object must provide for the alarm management capab…	SCTE-HMS-HEADENDIDENT-MIBHeFaultStatus Type Values: 1 normal 2 fault	.1.3.6.1.4.1.5591.1.11.1.4.1.1.2.1.4
heOpSwitchInputDescription A description of the switch input. The description text is to be determined by the equipment manufacturer. For example, Input A or Side B.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.5591.1.11.1.4.1.1.2.1.5

A table containing information about each Optical Switch 
output used in an indoor environment.

heOpSwitchOutputEntry row .1.3.6.1.4.1.5591.1.11.1.4.1.1.3.1

List of information about each optical switch output.

Indexes

ENTITY-MIBentPhysicalIndex heOpSwitchOutputIndex

Column	Syntax	OID
heOpSwitchOutputIndex Index number corresponding to the Optical Output.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5591.1.11.1.4.1.1.3.1.1
heOpSwitchOutputDescription A description of the switch output. The description text is to be determined by the equipment manufacturer. For example, Output A or Secondary Output.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.5591.1.11.1.4.1.1.3.1.2