heOpSwitchWaitToRestoreTime

SCTE-HMS-HE-OPTICAL-SWITCH-MIB · .1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.9
MIB view Table view

Object

column r/w 1 sec SNMPv2-SMIInteger32 
Controls hysteresis time in sec. 
              
If in automatic switching mode and revert mode is enabled,
		a switch back to the original side will be delayed for 
		the time specified by this object.

Context

MIB
SCTE-HMS-HE-OPTICAL-SWITCH-MIB
OID
.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.9
Type
column
Access
readwrite
Status
current
Units
1 sec
Parent
heOpSwitchUnitEntry
Table
heOpSwitchUnitTable
Siblings
8

Syntax

1 sec SNMPv2-SMIInteger32
Source
SNMPv2-SMIInteger32
Base type
Integer32

Values & Constraints

Type Constraints
range: -2147483648..2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
heOpSwitchMode
This controls and/or reports the switching mode. If automatic(1), the optical switch will evaluate the optical input status and make the decision to affect the switch state. …
columnEnumeration.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.1
heOpSwitchControl
Sets the intended state of the Optical Switch. The effect of this control will depend on the value of heOpSwitchMode. If heOpSwitchMode is set to automatic, the value this contr…
columnEnumeration.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.2
heOpSwitchRevertEnable
This controls the use of revertive switching. If set to on, the switch will attempt to go back to the preferred settings indicated by heOpSwitchControl if heOpS…
columnSCTE-HMS-HEADENDIDENT-MIBHeOnOffControl.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.3
heOpSwitchState
Reports the state of the Optical Switch. Not all enumerations must be supported. For example, an A-B optical switch may support only the pathA and pathB enumerations while a …
columnEnumeration.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.4
heOpSwitchFailoverStatus
The integral status of both inputs. A value is fault(2), if current switch state heOpSwitchState is different than the preferred setting heOpSwitchControl, o…
columnSCTE-HMS-HEADENDIDENT-MIBHeFaultStatus.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.5
heOpSwitchBothInputStatus
The integral status of both inputs. A value is fault(2), if both input levels are below the nominal value; otherwise, it is normal(1). This object m…
columnSCTE-HMS-HEADENDIDENT-MIBHeFaultStatus.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.6
heOpSwitchSelectWavelength
Wavelength feeding the particular input of the optical switch. Typical values might be 131000 (1310 nm) and 155000 (1550 nm).
column0.01 nm SCTE-HMS-HEADENDIDENT-MIBHeHundredthNanoMeter.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.7
heOpSwitchHysteresis
Controls switch input hysteresis amount. The amount of hysteresis used and the ability to change it is to be determined by the vendor.
column0.1 dB Integer32.1.3.6.1.4.1.5591.1.11.1.4.1.1.1.1.8