RAD-Clock-MIB Table View

Table-centric layout grouping table, row, and column objects.

Tables
22
Rows
22
Columns
296
.1.3.6.1.4.1.164.6.2.15.9.1 · 1 row entry · 8 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk gnssConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::gnssConfigTable'
A table of GNSS configuration entries.
gnssConfigEntry row .1.3.6.1.4.1.164.6.2.15.9.1.1
GNSS configuration entry.
Indexes
Column Syntax OID
Configure antenna cable delay
nanosecondsUnsigned32r/w
Constraints:
range: 0-999999
.1.3.6.1.4.1.164.6.2.15.9.1.1.1
Minimum elevation angle.
degreesUnsigned32r/w
Constraints:
range: 5-45
.1.3.6.1.4.1.164.6.2.15.9.1.1.2
GNSS selected as primary.
The value notApplicable (1) is not allowed.
GnssModer/w
Type Values:
1notApplicable
2gps
3glonass
4galileo
5beidou
.1.3.6.1.4.1.164.6.2.15.9.1.1.3
GNSS selected as secondary, if primary is not available.
GnssModer/w
Type Values:
1notApplicable
2gps
3glonass
4galileo
5beidou
.1.3.6.1.4.1.164.6.2.15.9.1.1.4
Positioning mode
Enumerationr/w
Enumerated Values:
1auto
2manual
.1.3.6.1.4.1.164.6.2.15.9.1.1.5
Applicable only when gnssConfigPosition = manual.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.15.9.1.1.6
Applicable only when gnssConfigPosition = manual.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.15.9.1.1.7
Applicable only when gnssConfigPosition = manual.
millimetersSNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.6.2.15.9.1.1.8
.1.3.6.1.4.1.164.6.2.15.9.2 · 1 row entry · 6 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk gnssStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::gnssStatusTable'
A table of GNSS status entries.
gnssStatusEntry row .1.3.6.1.4.1.164.6.2.15.9.2.1
Position data and status
Indexes
Column Syntax OID
Actual GNSS used
GnssMode
Type Values:
1notApplicable
2gps
3glonass
4galileo
5beidou
.1.3.6.1.4.1.164.6.2.15.9.2.1.1
GNSS tracking status:
notTracking (1): Not tracking satellite.
trackingSatellites (2): Tracking satellite.
gpsLocked (3): GNSS locked.
todLocked (4): TOD locked to the reference.
Enumeration
Enumerated Values:
1notTracking
2trackingSatellites
3gpsLocked
4todLocked
.1.3.6.1.4.1.164.6.2.15.9.2.1.2
Latitude coordinates, formatted ndd:mm:ss.sss or sdd:mm:ss.sss
(n=north / s=south, dd=degrees, mm=minutes, ss=seconds)
SNMP-FRAMEWORK-MIBSnmpAdminString
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.15.9.2.1.3
Longitude coordinates, formatted eddd:mm:ss.sss or wddd:mm:ss.sss
(e=east/ w=west, dd=degrees, mm=minutes, ss=seconds)
SNMP-FRAMEWORK-MIBSnmpAdminString
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.15.9.2.1.4
Altitude in millimmeters
millimetersSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.6.2.15.9.2.1.5
Each bit represent poissible GNSS port hardware failure reason.
when no failure, the value will be 0.
Bits
Enumerated Values:
0voltageOra
1currentOra
2shortCircuit
3openCircuit
4signalLow
5noAntennaPower
6other
7noResponseFromModule
.1.3.6.1.4.1.164.6.2.15.9.2.1.6
.1.3.6.1.4.1.164.6.2.15.9.3 · 1 row entry · 6 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk gnssSatelliteTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::gnssSatelliteTable'
A table of GNSS satellites status entries.
gnssSatelliteEntry row .1.3.6.1.4.1.164.6.2.15.9.3.1
GNSS satellites status entry.
Column Syntax OID
running index of the satellite table.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.15.9.3.1.1
Satelite number.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.15.9.3.1.2
Satellite Signal to Noise Ratio
dbSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.6.2.15.9.3.1.3
Satellite health status.
Enumeration
Enumerated Values:
1no
2yes
.1.3.6.1.4.1.164.6.2.15.9.3.1.4
Azimuth to satellite
DegreesSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.6.2.15.9.3.1.5
Satellite elevation angle
DegreesSNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.6.2.15.9.3.1.6
.1.3.6.1.4.1.164.6.2.52.1 · 1 row entry · 14 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnClkSrcPortTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnClkSrcPortTable'
Pool of Ports for the Master/Fallback Clock Source
and of Recovered/Distributed Clock IDs.
For devices with more than one configuration:
Set operation is valid only to the TmpCnfg entry.
agnClkSrcPortEntry row .1.3.6.1.4.1.164.6.2.52.1.1
An entry in the table.
Column Syntax OID
This object indicates the Idx of the Cnfg being
accessed ; Idx of 255 relates to the TmpCnfg.
For product supporting a single configuration, the value will be 1.
Integer32
Constraints:
range: 1-2147483647
.1.3.6.1.4.1.164.6.2.52.1.1.1
Clock Source Index.
master - refers to Master clock
fallback - refers to Fallback clock
recovered - refers to Recovered PTP1588 clock
distributed - refers to Distributed PTP1588 clock
g82751Recovered - refers …
Enumeration
Enumerated Values:
1master
2fallback
3recovered
4distributed
5g82751Recovered
6g82751Distributed
7g82752Recovered
8g82752Distributed
.1.3.6.1.4.1.164.6.2.52.1.1.2
This object indicates the running Idx of the Port/Recovered/Distributed ID that is
to be used as Clock Source, for each agnClkSrcPortSrcIdx instance.
Integer32
Constraints:
range: 1-2147483647
.1.3.6.1.4.1.164.6.2.52.1.1.3
This object indicates the Port/Interface/Recovered ID # that is
to be used as Clock Source.

In case of agnClkSrcPortSrcIdx = recovered(3):
- When agnClkSrcPortType = adaptive(2) - it indicates the PW nu…
Integer32r/w
Constraints:
range: 1-2147483647
.1.3.6.1.4.1.164.6.2.52.1.1.4
This object enables Creation/ Deletion of rows in the table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.164.6.2.52.1.1.5
This object indicates the Recovered/Distributed Clock Administrative Status.
Enumerationr/w
Enumerated Values:
1notApplicable
2down
3up
.1.3.6.1.4.1.164.6.2.52.1.1.6
This object is relevant only in case of Recovered/Distributed Clock.
It indicates the Clock Type.

In case of value = ieee1588v2, it represents 1588v2 clocks as follows:
- If agnClkSrcPortSrcIdx = recover…
Enumerationr/w
Enumerated Values:
1notApplicable
2adaptive
3ieee1588v2
4commonClock
5g82751
6g82752
.1.3.6.1.4.1.164.6.2.52.1.1.7
This object indicates the Clock Source Quality.
Enumerationr/w
Enumerated Values:
1notApplicable
2stratum1
3stratum2
4stratum3
5stratum3e
6stratum4
.1.3.6.1.4.1.164.6.2.52.1.1.8
This object is relevant only in case of Recovered Clock.
It indicates the Clock Network Type, i.e.
the PSN network characteristics and behavior.
Enumerationr/w
Enumerated Values:
1notApplicable
2typeA
3typeB
4typeC
5typeD
6typeE
7typeF
.1.3.6.1.4.1.164.6.2.52.1.1.9
This object indicates the Frequency Clock State.

freeRun(1) -
Clock recovery is not locked to any clock.

frequencyAcquisition(2) -
Adaptive clock recovery is learning the frequency.
Enumeration
Enumerated Values:
1freeRun
2frequencyAcquisition
3rapidPhaseLock
4finePhaseLock
5holdover
6notApplicable
7locking
8idle
9frequencyLock
10holdoverPackets
11acquiringPackets
12lockPackets
13holdoverPhyPackets
14acquiringPhyPackets
15lockPhyClock
.1.3.6.1.4.1.164.6.2.52.1.1.10
This object indicates the Src Type of each entry in the list of source
instances, when agnClkSrcPortSrcIdx=master(1)or fallback(2).
According to this type, agnClkSrcPort gets the relevant meaning (Port index
or Recovere…
Enumerationr/w
Enumerated Values:
1notApplicable
3rxClock
12recovered
.1.3.6.1.4.1.164.6.2.52.1.1.11
This object indicates the Time Clock State.

freeRun(1) - Clock recovery is not locked to any clock.

acquisition(2) - Adaptive clock recovery is learning the time.

holdover(3)…
Enumeration
Enumerated Values:
1freeRun
2acquisition
3holdover
4notApplicable
5lock
.1.3.6.1.4.1.164.6.2.52.1.1.12
By default, agent will set the value of this object as follows:
If agnClkSrcPortSrcIdx value is equal to
distributed (4) -> PTP (1588) master name
If agnClkSrcPortSrcIdx value is equal to
recovered (3) -> PTP (15…
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.52.1.1.13
This object indicates the Clock Mode when Clock type is G.8275.1
(meaning agnClkSrcPortSrcIdx=(5) or (6), and agnClkSrcPortType=5
notApplicable(1) - means agnClkSrcPortSrcIdx is not equal to 5 or 6.
ordinaryClock(2) …
Enumeration
Enumerated Values:
1notApplicable
2ordinaryClock
3boundaryClock
.1.3.6.1.4.1.164.6.2.52.1.1.14
.1.3.6.1.4.1.164.6.2.52.2 · 1 row entry · 8 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnCurrClkTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnCurrClkTable'
Current Clock Source.
agnCurrClkEntry row .1.3.6.1.4.1.164.6.2.52.2.1
An entry in the table.
Column Syntax OID
This MIB object identifies the object for which the Clock Source
is used (System, Other System, Card).
Integer32
Constraints:
range: 1-2147483647
.1.3.6.1.4.1.164.6.2.52.2.1.1
Current Clock Source Mode.
master - refers Master clock
fallback - refers Fallback clock
internal - only when both Master and Fallback Sources failed
Enumeration
Enumerated Values:
1master
2fallback
3internal
.1.3.6.1.4.1.164.6.2.52.2.1.2
This object indicates the Current Clock Source.
Enumeration
Enumerated Values:
1none
2internal
3rxClk
4station
5lbt
6ntr
7adaptive
8stationB
9automatic
10system
11sSubsystem
12recovered
255notApplicable
.1.3.6.1.4.1.164.6.2.52.2.1.3
This object indicates the Port/Interface/Recovered ID that is
Currently used as Clock Source.
- When agnCurrClkSrc=rxClock(3), this object indicates a Port index.
- When agnCurrClkSrc=recovered(12), this object indicate…
Integer32
Constraints:
range: 1-2147483647
.1.3.6.1.4.1.164.6.2.52.2.1.4
Current Clock Holdover State.
As a last resort, in the absence of higher quality timing:
- a SONET/SDH object can enter 'holdover' state, until higher quality
external timing becomes available again. In this state (va…
Enumeration
Enumerated Values:
1notApplicable
2no
3yes
.1.3.6.1.4.1.164.6.2.52.2.1.5
This parameter indicates whether clock source
is selected based on receive clock quality.
Clock quality is indicated in S1 byte inside SONET/SDH overhead,
(encoded as SSM - Synchronization Status Messaging).
Enumeration
Enumerated Values:
1notApplicable
2no
3yes
.1.3.6.1.4.1.164.6.2.52.2.1.6
This object indicates the Current Clock State.

freeRun(1) -
Current clock state machine is not locked
and run from the internal oscillator.

rapidPhaseLock(2) -
Current clock state machine i…
Enumeration
Enumerated Values:
1freeRun
2rapidPhaseLock
3finePhaseLock
4holdover
5frequencyAcquisition
.1.3.6.1.4.1.164.6.2.52.2.1.7
This object indicates the Current Clock Qualification
and defines whether the PLL can locked according to the stratum definitions.
Enumeration
Enumerated Values:
1notApplicable
2disqualified
3qualified
.1.3.6.1.4.1.164.6.2.52.2.1.8
.1.3.6.1.4.1.164.6.2.52.3.1 · 1 row entry · 5 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnClkCurrentTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnClkCurrentTable'
The Clock Current table.
agnClkCurrentEntry row .1.3.6.1.4.1.164.6.2.52.3.1.1
An entry in the Clock Current table.
Column Syntax OID
An Index that is uniquely represents the Clock.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.1.1.1
The counter associated with the number of Received Packets,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.1.1.2
The counter associated with the number of Lost Packets,
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.1.1.3
The counter associated with the number of times Out-of-Order Packets
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.1.1.4
The counter associated with the number of times Underflow event
encountered by a Bridge Port in the current 15 minute interval.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.1.1.5
.1.3.6.1.4.1.164.6.2.52.3.2 · 1 row entry · 6 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnClkIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnClkIntervalTable'
The Clock Interval table.
agnClkIntervalEntry row .1.3.6.1.4.1.164.6.2.52.3.2.1
An entry in the Clock Interval table.
Column Syntax OID
An Index that is uniquely represents the Clock.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.2.1.1
A number between 1 and 96,
where 1 is the most recently completed 15 minute interval
and 96 is the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.2.1.2
The counter associated with the number of Received Packets,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.2.1.3
The counter associated with the number of Lost Packets,
encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.2.1.4
The counter associated with the number of times Out-of-Order Packets
are detected, encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.2.1.5
The counter associated with the number of times Underflow event
is detected, encountered by a Bridge Port in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.3.2.1.6
.1.3.6.1.4.1.164.6.2.52.4.1 · 1 row entry · 34 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkTable'
The PTP (Precision Time Protocol, IEEE-1588v2) Clock table.
          
Entries are created/deleted to/from this table upon a set of
agnClkSrcPortRowStatus (from agnClkSrcPortTable) and only when
agnClkSrcPortType = ieee1588v2(3) or g82751(5) or g82752(6).
agnPtpClkEntry row .1.3.6.1.4.1.164.6.2.52.4.1.1
An entry in the PTP Clock table.
Column Syntax OID
This object uniquely represents the PTP Clock Type(PTP1588 or,
G.8275.1, or G.8275.2, Master or Slave, same as agnClkSrcPortSrcIdx
(from agnClkSrcPortTable).
Enumeration
Enumerated Values:
3ieee1588Slave
4ieee1588Master
5g82751Slave
6g82751Master
7g82752Slave
8g82752Master
.1.3.6.1.4.1.164.6.2.52.4.1.1.1
This object uniquely represents the PTP Clock ID,
same as agnClkSrcPortIdx (from agnClkSrcPortTable).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.2
This object indicates the Source Port Clock ID,
within the Source Port Identity.
OctetStringr/w
Constraints:
range: 8-8
.1.3.6.1.4.1.164.6.2.52.4.1.1.3
This object indicates the Source Port Number,
within the Source Port Identity.
OctetStringr/w
Constraints:
range: 2-2
.1.3.6.1.4.1.164.6.2.52.4.1.1.4
This object indicates the Sync Rate of the packet,
which is transmitted from the master clock towards the slave clock.
Enumerationr/w
Enumerated Values:
1notApplicable
2r32pps
3r64pps
4r128pps
5r16pps
.1.3.6.1.4.1.164.6.2.52.4.1.1.5
This object indicates the stability of the master clock.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.6
This object indicates the Type of the Address, used by this PTP clock.
INET-ADDRESS-MIBInetAddressTyper/w
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
.1.3.6.1.4.1.164.6.2.52.4.1.1.7
This object indicates the Multicast Address, according to agnPtpClkAddrType.
INET-ADDRESS-MIBInetAddressr/w
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.52.4.1.1.8
This object indicates the TOS value (range is 0..255) or the DSCP value
(range is 0..64) of the PTP frame.
255 = not applicable
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.9
This object indicates the Priority bit value (range is 0..7)
of the PTP frame.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.10
The number of previous 15-minutes intervals for which data was collected.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.11
This object indicates the number of seconds that have elapsed
since the beginning of the current error-measurement period
(range is 0..899).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.12
The counter associated with the number of Transmitted Sync Packets,
encountered by this PTP clock in the current 15 minute interval.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.13
The counter associated with the number of Received Sync Packets,
encountered by this PTP clock in the current 15 minute interval.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.14
The counter associated with the number of Received Followup Packets,
encountered by this PTP clock in the current 15 minute interval.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.15
This object indicates the PTP clock state.
Failuer - The clock state is - Failuer
OK - The clock state is - OK
Lld - Lower Layer Down
Enumeration
Enumerated Values:
1notApplicable
2failure
3ok
4lld
.1.3.6.1.4.1.164.6.2.52.4.1.1.16
This object indicates the PTP clock QL that transmit to the CSM.
ClockQlList
Type Values:
1type1Prc
2type1SsuA
3type1SsuB
4type1Sec
5type1Dnu
6type1SsmBased
21type2Prs
22type2Stu
23type2St2
24type2Tnc
25type2St3e
26type2St3
27type2Smc
28type2St4
29type2Dus
30type2SsmBased
31type2Prov
41type3Unk
42type3Sec
43type3Dnu
44type3SsmBased
255notApplicable
.1.3.6.1.4.1.164.6.2.52.4.1.1.17
The identity of the clock.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.18
This object defines the revertive mode.
Enumerationr/w
Enumerated Values:
1notApplicable
2nonRevertive
3revertive
.1.3.6.1.4.1.164.6.2.52.4.1.1.19
Wait to Restore (WTR) time in sec.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.20
For PTP Slave - The domain number in the send header message,
use to verify that the domain number in the receive message is the same,
otherwise the package will be discard.
For PTP Master - The domain that Master clock…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.21
The IP Address of the Slave, used in NE with more then one Slaves.
INET-ADDRESS-MIBInetAddressr/w
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.52.4.1.1.22
This object indicates the current active master per slave(recovered).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.23
This object enables to combine between the 1588 and the syncE clock recovery.
The actual frequency used from clock selector output to 1588 does not
need to be configured.
Default: timeFrequency
Enumerationr/w
Enumerated Values:
1frequency
2timeFrequency
3time
.1.3.6.1.4.1.164.6.2.52.4.1.1.24
This object sets the maximum number of registered slaves per Master.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.25
This object set the community domain.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.1.1.26
This object indicates the Master Status.
Bits
Enumerated Values:
0ok
1todFailure
2lppsFailure
.1.3.6.1.4.1.164.6.2.52.4.1.1.27
This object indicates the Type of the Address for agnPtpClkIpAddress.
INET-ADDRESS-MIBInetAddressTyper/w
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
.1.3.6.1.4.1.164.6.2.52.4.1.1.28
Setting this object to masterToSlave(2) or slaveToMaster(3), will enforce a clear
operation for agnPtpClkNetMetricsCurrentTable (Master to Slave or Slave to Master) Counters. Upon completion,
the value will automaticall…
Enumerationr/w
Enumerated Values:
1off
2masterToSlave
3slaveToMaster
4all
.1.3.6.1.4.1.164.6.2.52.4.1.1.29
The identity of the clock.
SNMP-FRAMEWORK-MIBSnmpAdminString
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.52.4.1.1.30
The object use to compensate between TX and RX packet delay.
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.6.2.52.4.1.1.31
The object set the 1PPS algorithm to:
enable - recovered frequency and time
disable - recovered time only.
Enumerationr/w
Enumerated Values:
1enable
2disable
3notApplicable
.1.3.6.1.4.1.164.6.2.52.4.1.1.32
The object set the profile type.
Enumerationr/w
Enumerated Values:
1notApplicable
2telecomEndToEnd
3telecomPeerToPeer
.1.3.6.1.4.1.164.6.2.52.4.1.1.33
This object is relevant when agnPtpClkType=g82751Master(6).
It is used in the execution of the best master clock algorithm.
Lower values take precedence. It provides finer grained ordering
among otherwise equivalent c…
Unsigned32r/w
Constraints:
range: 0-255
.1.3.6.1.4.1.164.6.2.52.4.1.1.34
.1.3.6.1.4.1.164.6.2.52.4.2 · 1 row entry · 9 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkMasterStreamTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkMasterStreamTable'
The PTP Master Clock Stream table.
agnPtpClkMasterStreamEntry row .1.3.6.1.4.1.164.6.2.52.4.2.1
An entry in the PTP Master Clock Stream table.
Column Syntax OID
This object uniquely represents the PTP Master Clock ID,
same as agnPtpClkId when agnPtpClkType = ieee1588Master(4).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.2.1.1
This object uniquely represents the Stream ID of the PTP master clock.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.2.1.2
This object enables the user to create/delete entries (streams) in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.164.6.2.52.4.2.1.3
This object indicates the Administrative Status of the stream.
Enumerationr/w
Enumerated Values:
2down
3up
.1.3.6.1.4.1.164.6.2.52.4.2.1.4
This object indicates the Name of the stream.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.52.4.2.1.5
This object indicates the Peer ID of the stream.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.2.1.6
The number of previous 15-minutes intervals for which data was collected.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.2.1.7
This object indicates the number of seconds that have elapsed
since the beginning of the current error-measurement period
(range is 0..899).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.2.1.8
The counter associated with the number of Transmitted Sync Packets,
encountered by this stream in the current 15 minute interval.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.2.1.9
.1.3.6.1.4.1.164.6.2.52.4.3 · 1 row entry · 4 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkIntervalTable'
The PTP Clock 15 minutes Intervals table.
agnPtpClkIntervalEntry row .1.3.6.1.4.1.164.6.2.52.4.3.1
An entry in the PTP Clock 15 minutes Interval table.
Column Syntax OID
A number between 1 and 96,
where 1 is the most recently completed 15 minute interval
and 96 is the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.3.1.1
The counter associated with the number of Transmitted Sync Packets,
encountered by a PTP Clock in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.3.1.2
The counter associated with the number of Received Sync Packets,
encountered by a PTP Clock in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.3.1.3
The counter associated with the number of Received Followup Packets,
encountered by a PTP Clock in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.3.1.4
.1.3.6.1.4.1.164.6.2.52.4.4 · 1 row entry · 2 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkMasterStreamIntTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkMasterStreamIntTable'
The PTP Master Clock Stream Intervals Statistics table.
agnPtpClkMasterStreamIntEntry row .1.3.6.1.4.1.164.6.2.52.4.4.1
An entry in the PTP Master Clock Interval table.
Column Syntax OID
A number between 1 and 96,
where 1 is the most recently completed 15 minute interval
and 96 is the least recently completed 15 minutes interval
(assuming that all 96 intervals exist).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.4.1.1
The counter associated with the number of Transmitted Sync Packets,
encountered by this stream in one of the previous 96,
individual 15 minute, intervals.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.4.1.2
.1.3.6.1.4.1.164.6.2.52.4.5 · 1 row entry · 27 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkCounterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkCounterTable'
The table contains countars for PTP (1588) .
agnPtpClkCounterEntry row .1.3.6.1.4.1.164.6.2.52.4.5.1
An entry in the PTP Clock.
Column Syntax OID
Setting this object to on, will enforce a clear statistics
counters. The command will clear statistics from all
agnPtpClkCounterTable.
Upon completion, the value will automatically change to off(2).
Default=off(2).
Enumerationr/w
Enumerated Values:
2off
3on
.1.3.6.1.4.1.164.6.2.52.4.5.1.1
The number of unicast Announce Message type requests that were sent from slave to master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.2
The number of unicast Announce Message type accepts that were sent from master to slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.3
The number of unicast Announce Message type rejects that were sent from master to slave.
The durationField shall be equal to zero.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.4
The number of unicast Announce Message types that were received
after timeout (60 Sec) from the master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.5
The number of unicast Sync Message type requests that were sent from slave to master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.6
The number of unicast Sync Message type accepts that were sent from master to slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.7
The number of unicast Sync Message type rejects that were sent from master to slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.8
The number of unicast Sync Message types that were received
after timeout (60 Sec) from the master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.9
The accumulated seconds of agnPtpNoUnicastSyncElapsedTime
object. This counter defines the cumulated elapsed time (in seconds) that the slave
did not receive Sync Message types from the master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.10
The number of seconds that the slave did not receive Sync Message
from the master from the last Sync Message.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.11
The accumulated seconds of agnPtpNoUnicastAnnounceElapsedTime
object. This counter defines the cumulated elapsed time (in seconds) that the slave
did not receive Announce Message types from the master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.12
The number of seconds that the slave did not receive Announce Message
from the master from the last Announce Message.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.13
The number of unicast Sync Message type that were received by the slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.14
The number of unicast Sync Messages that were mis-ordered.
e.g. Sync Message 5 was received before Sync Message 4.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.15
The number of lost unicast Sync Messages from master to slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.5.1.16
The sum of all packet transmitted by the 1588 master (to all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.17
The sum of only SYNC packets transmitted by master (to all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.18
The sum of only FOLLOW UP packets transmitted by master (to all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.19
The sum of only DELAY RESPONSE packets transmitted by master (to all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.20
The sum of only ANNOUNCE packets transmitted by master (to all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.21
The sum of only FOLLOW UP packets transmitted by master (to all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.22
The sum of all classified 1588 master received packets
(Delay request and signaling packets from all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.23
The sum of only Signaling packets received by master (from all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.24
The sum of only DELAY REQUEST packets received by master (from all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.25
The Counts only the SIGNALING packets that discarded by the master (from all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.26
The sum of only ANNOUNCE packets received by master (from all slaves).
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.5.1.27
.1.3.6.1.4.1.164.6.2.52.4.6 · 1 row entry · 28 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpMultiMasterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpMultiMasterTable'
The table contains configuration and status for PTP Recovered (Slave)
Masters.
The table contains 2 indexes, first index is indicate the
Recovered (Slave) ID from agnPtpClkTable, seconds index see agnPtpMultiMasterId.
agnPtpMultiMasterEntry row .1.3.6.1.4.1.164.6.2.52.4.6.1
An entry in the Table.
Column Syntax OID
This index indicate the master number.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.6.1.1
This object enables the user to create/delete entries in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.164.6.2.52.4.6.1.2
This object uniquely represents the PTP Master Clock ID
Default: clock-id = 0xFFFFFFFFFFFFFFFF.
OctetStringr/w .1.3.6.1.4.1.164.6.2.52.4.6.1.3
This object uniquely represents the PTP Master Port Number
Default: port-number = 0xFFFF.
OctetStringr/w .1.3.6.1.4.1.164.6.2.52.4.6.1.4
This object indicates the Master Clock Identity, the value of this object
is a combination of agnPtpMultiMasterClockId and agnPtpMultiMasterPortNumber
OctetString .1.3.6.1.4.1.164.6.2.52.4.6.1.5
The priority of the master clock.
This parameter is used to in case that the masters have the same QL.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.6.1.6
The Network Type indicates the PSN network characteristics and behavior.
Enumerationr/w
Enumerated Values:
1auto
2dsl
.1.3.6.1.4.1.164.6.2.52.4.6.1.7
This object represents the Peer Index (from peerTable).
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.6.1.8
The sync message rate that the slave request from the master.
SyncRater/w
Type Values:
1r16pps
2r32pps
3r64pps
4r128pps
.1.3.6.1.4.1.164.6.2.52.4.6.1.9
The minimum sync message rate that the slave can request from the master.
SyncRater/w
Type Values:
1r16pps
2r32pps
3r64pps
4r128pps
.1.3.6.1.4.1.164.6.2.52.4.6.1.10
The period of time (in seconds) that the slave ask from the master to send
the sync message.
0 = disable.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.6.1.11
The announce message rate that the slave request from the master.
AnnounceRater/w
Type Values:
1r125msec
2r250msec
3r500msec
4r1sec
5r2sec
6r4sec
7r8sec
8r16sec
.1.3.6.1.4.1.164.6.2.52.4.6.1.12
The minimum announce message rate that the slave can request from the master.
AnnounceRater/w
Type Values:
1r125msec
2r250msec
3r500msec
4r1sec
5r2sec
6r4sec
7r8sec
8r16sec
.1.3.6.1.4.1.164.6.2.52.4.6.1.13
The period of time (in seconds) that the slave ask from the master to send
the announce message.
0 = disable.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.6.1.14
The actual QL of csmDomainCurrentSourceId dependent on
csmDomainSynchNetType.
ClockQlListr/w
Type Values:
1type1Prc
2type1SsuA
3type1SsuB
4type1Sec
5type1Dnu
6type1SsmBased
21type2Prs
22type2Stu
23type2St2
24type2Tnc
25type2St3e
26type2St3
27type2Smc
28type2St4
29type2Dus
30type2SsmBased
31type2Prov
41type3Unk
42type3Sec
43type3Dnu
44type3SsmBased
255notApplicable
.1.3.6.1.4.1.164.6.2.52.4.6.1.15
This object enable/disable the Master source.
Enumerationr/w
Enumerated Values:
2no
3yes
.1.3.6.1.4.1.164.6.2.52.4.6.1.16
The QL that was received from the master.
ClockQlList
Type Values:
1type1Prc
2type1SsuA
3type1SsuB
4type1Sec
5type1Dnu
6type1SsmBased
21type2Prs
22type2Stu
23type2St2
24type2Tnc
25type2St3e
26type2St3
27type2Smc
28type2St4
29type2Dus
30type2SsmBased
31type2Prov
41type3Unk
42type3Sec
43type3Dnu
44type3SsmBased
255notApplicable
.1.3.6.1.4.1.164.6.2.52.4.6.1.17
The Sync Rate that was granted from the master.
SyncRate
Type Values:
1r16pps
2r32pps
3r64pps
4r128pps
.1.3.6.1.4.1.164.6.2.52.4.6.1.18
The Sync Period that was granted from the master.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.6.1.19
The Announce Rate that was granted from the master.
AnnounceRate
Type Values:
1r125msec
2r250msec
3r500msec
4r1sec
5r2sec
6r4sec
7r8sec
8r16sec
.1.3.6.1.4.1.164.6.2.52.4.6.1.20
The Announce Period that was granted from the master.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.6.1.21
This object indicates the status of the master clock.
PSTF - Packet Timing Signal Fail.
Enumeration
Enumerated Values:
2active
3notActive
.1.3.6.1.4.1.164.6.2.52.4.6.1.22
This object set the delay-respond message rate that the slave request from the master.
The delay-respond rate mast be equal or lower that the sync rate.
Default: 128pps.
SyncRater/w
Type Values:
1r16pps
2r32pps
3r64pps
4r128pps
.1.3.6.1.4.1.164.6.2.52.4.6.1.23
The minimum Delay Respond message rate that the slave can request from the master.
The minimum-expected must be lower or equal to the request-rate.
Default: 128pps.
SyncRater/w
Type Values:
1r16pps
2r32pps
3r64pps
4r128pps
.1.3.6.1.4.1.164.6.2.52.4.6.1.24
The period of time (in seconds) that the slave ask from the master to send
the delay-respond message.
Default: 300 (sec).
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.6.1.25
The Sync Period that was granted from the master.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.6.1.26
The period of time (in seconds) that the slave ask from the master to send
the delay-respond message.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.6.1.27
The object use to compensate between TX and RX packet delay.
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.164.6.2.52.4.6.1.28
.1.3.6.1.4.1.164.6.2.52.4.7 · 1 row entry · 34 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpMultiMasterCounterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpMultiMasterCounterTable'
The table contains countars for PTP (1588) .
agnPtpMultiMasterCounterEntry row .1.3.6.1.4.1.164.6.2.52.4.7.1
An entry in the PTP Clock.
Column Syntax OID
Setting this object to on, will enforce a clear statistics
Counters.Upon completion, the value will automatically chagne to off(2).
Default=off(2).
Enumerationr/w
Enumerated Values:
2off
3on
.1.3.6.1.4.1.164.6.2.52.4.7.1.1
The number of unicast Announce Message type requests that were sent from
slave to master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.2
The number of unicast Announce Message type accepts that were sent from
master to slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.3
The number of unicast Announce Message type rejects that were sent from
master to slave. The durationField shall be equal to zero.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.4
The number of unicast Announce Message types that were received
after timeout (60 Sec) from the master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.5
The number of unicast Sync Message type requests that were sent from
slave to master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.6
The number of unicast Sync Message type accepts that were sent from
master to slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.7
The number of unicast Sync Message type rejects that were sent from master to slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.8
The number of unicast Sync Message types that were received
after timeout (60 Sec) from the master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.9
The accumulated seconds of agnPtpMultiMasterNoUnicastSyncElapsedTime
object. This counter defines the cumulated elapsed time (in seconds) that
the slave did not receive Sync Message types from the master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.10
The number of seconds that the slave did not receive Sync Message
from the master from the last Sync Message.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.11
The accumulated seconds of agnPtpMultiMasterNoAnnounceElapsedTime
object. This counter defines the cumulated elapsed time (in seconds) that the slave
did not receive Announce Message types from the master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.12
The number of seconds that the slave did not receive Announce Message
from the master from the last Announce Message.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.13
The number of unicast Sync Message type that were received by the slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.14
The number of unicast Sync Messages that were mis-ordered.
e.g. Sync Message 5 was received before Sync Message 4.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.15
The number of lost unicast Sync Messages from master to slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.16
Setting this object to on, will enforce a clear Sync statistics Counters.
Upon completion, the value will automatically chagne to off(2).
Default=off(2).
Enumerationr/w
Enumerated Values:
2off
3on
.1.3.6.1.4.1.164.6.2.52.4.7.1.17
The actual sync rate message that receive from the 1588 master.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.18
The highest value that was measured in agnPtpMultiMasterMeasuredSyncRate.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.19
The lowest value that was measured in agnPtpMultiMasterMeasuredSyncRate.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.20
The number of unicast Delay Respond Message type requests that were sent from
slave to master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.21
The number of unicast Delay Respond Message type accepts, that were sent from
master to slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.22
The number of unicast Delay Respond Message type rejects that were sent from
master to slave. The duration Field shall be equal to zero.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.23
The number of unicast Delay Respond Message types that were received
after timeout (60 Sec) from the master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.24
The accumulated seconds of agnPtpMultiMasterNoDelayRespondElapsedTime
object. This counter defines the cumulated elapsed time (in seconds) that the slave
did not receive Delay Respond Message types from the master.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.25
The number of seconds that the slave did not receive Delay Respond Message
from the master from the last Delay Respond Message.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.26
The number of unicast Delay Respond Message type that were received by the slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.27
The number of unicast Delay Respond Message type that were received by the slave.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.28
The number of unicast Delay Respond Message type that were received by the slave.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.29
The actual Delay Respond rate message that receive from the 1588 master.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.30
The highest value that was measured in agnPtpMultiMasterMeasuredDelayRespondRate.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.31
The lowest value that was measured in agnPtpMultiMasterMeasuredDelayRespondRate.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.32
.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.52.4.7.1.33
The number of unicast Delay Request Message type that were sent by the slave.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.7.1.34
.1.3.6.1.4.1.164.6.2.52.4.8 · 1 row entry · 18 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkSlaveTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkSlaveTable'
The table contains statuses and countars of the 1588 slave that registered on
a 1588 master.
agnPtpClkSlaveEntry row .1.3.6.1.4.1.164.6.2.52.4.8.1
An entry in the PTP Clock.
Column Syntax OID
Type of the IP Address designated by deviceAccessIpAddress
INET-ADDRESS-MIBInetAddressType
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
.1.3.6.1.4.1.164.6.2.52.4.8.1.1
The IP number of slave.
INET-ADDRESS-MIBInetAddress
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.52.4.8.1.2
This object reset all the Master and the Slave counters.
Setting this object to on, will enforce a clear statistics
Counters.Upon completion, the value will automatically chagne to off(2).
Default=off(2).
Enumerationr/w
Enumerated Values:
2off
3on
.1.3.6.1.4.1.164.6.2.52.4.8.1.3
The number of Sync packets transmitted by master.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.8.1.4
The number of delay response packets transmitted by master.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.8.1.5
The number of delay response packets transmitted by master .
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.8.1.6
The number of announce packets transmitted by master.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.8.1.7
The number of signaling packets transmitted by master .
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.8.1.8
The number of signaling packets received by master .
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.8.1.9
The number of delay request packets received by master .
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.8.1.10
The number of signaling packets that discarded by the SW.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.8.1.11
This object indicates the validity of the slave.
Enumeration
Enumerated Values:
2off
3on
.1.3.6.1.4.1.164.6.2.52.4.8.1.12
In this SYNC mode, the delay response and announce
messages will be transmitted by the master to the salve.
Enumeration
Enumerated Values:
2frequency
3frequencyAndTime
.1.3.6.1.4.1.164.6.2.52.4.8.1.13
The 1588 PTP slave unique identifier.
SNMP-FRAMEWORK-MIBSnmpAdminString
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.52.4.8.1.14
The announce Interval is the rate (packets per second) of
the Announce packets transmitted by the master to the slave
Enumeration
Enumerated Values:
1r1
2r2
3r4
4r8
5r16
6r125m
7r250m
8r500m
.1.3.6.1.4.1.164.6.2.52.4.8.1.15
The number of seconds for which the Announce messages shall be transmitted
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.8.1.16
The Delay Response Interval is the rate (packets per second) of the
Delay Response packets transmitted by the master to the slave.
Enumeration
Enumerated Values:
1r1
2r2
3r4
4r8
5r16
6r125m
7r250m
8r500m
9r16pps
10r32pps
11r64pps
12r128pps
.1.3.6.1.4.1.164.6.2.52.4.8.1.17
The number of seconds for the Delay Response messages shall be transmitted
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.8.1.18
.1.3.6.1.4.1.164.6.2.52.4.9 · 1 row entry · 7 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkNetMetricsCurrentTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkNetMetricsCurrentTable'
The Clock network metrics current statistics table.
agnPtpClkNetMetricsCurrentEntry row .1.3.6.1.4.1.164.6.2.52.4.9.1
An entry in the table.
Column Syntax OID
An Index that is uniquely represents the Clock entity.
The index shall be equal to agnPtpClkId.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.9.1.1
This object indicates the direction of the statistics.
Enumeration
Enumerated Values:
1masterToSlave
2slaveToMaster
.1.3.6.1.4.1.164.6.2.52.4.9.1.2
This object indicates the metrics ID.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.9.1.3
This object indicates the measuring window time of the
statistics, ( The time is sec ).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.9.1.4
A Time Deviation metric based on Allan Variance. Measures standard
deviation of a packet network frequency instability (caused by PDV)
over a specific observation period Tau.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.9.1.5
A minimum Time Deviation metric based on Allan variance. Measures
frequency instability standard deviation of the early arriving packets
only (with minimum network delay) over a specific observation period Tau.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.9.1.6
The number of seconds that the statistics were accumulated from the last statistic reset.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.9.1.7
.1.3.6.1.4.1.164.6.2.52.4.10 · 1 row entry · 8 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkNetMetricsIntervalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkNetMetricsIntervalTable'
The Clock Net Metrics Interval table
The duration of each interval is 1 hour.
agnPtpClkNetMetricsIntervalEntry row .1.3.6.1.4.1.164.6.2.52.4.10.1
An entry in the Clock Interval statistic table.
Column Syntax OID
An Index that is uniquely represents the Clock entity.
The index shall be equal to agnPtpClkId.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.10.1.1
This object indicates the direction of the statistics
Enumeration
Enumerated Values:
1masterToSlave
2slaveToMaster
.1.3.6.1.4.1.164.6.2.52.4.10.1.2
This object indicates the metrics ID.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.10.1.3
The Interval Number. This number is between 1 and x, where 1 is the
most recently completed interval and x is the least recently
completed interval.
Unsigned32
Constraints:
range: 1-24
.1.3.6.1.4.1.164.6.2.52.4.10.1.4
This object indicates the measuring window time of the
statistics ( The time is sec ).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.10.1.5
A Time Deviation metric based on Allan Variance. Measures standard
deviation of a packet network frequency instability (caused by PDV)
over a specific observation period Tau.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.10.1.6
A minimum Time Deviation metric based on Allan variance. Measures
frequency instability standard deviation of the early arriving packets
only (with minimum network delay) over a specific observation period Tau.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.10.1.7
The number of seconds that have elapsed since the beginning
of the interval.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.10.1.8
.1.3.6.1.4.1.164.6.2.52.4.11 · 1 row entry · 2 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkNetMetricsIntervalMasterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkNetMetricsIntervalMasterTable'
This table includes the master ID that was active during the interval.
agnPtpClkNetMetricsIntervalMasterEntry row .1.3.6.1.4.1.164.6.2.52.4.11.1
An entry in the Clock Interval table.
Column Syntax OID
The Master ID that was active during the interval.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.4.11.1.1
The date and time of the sampling that occurs during the interval.
SNMPv2-TCDateAndTime
Type Constraints:
range: 8
range: 11
Description:
A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …
.1.3.6.1.4.1.164.6.2.52.4.11.1.2
.1.3.6.1.4.1.164.6.2.52.4.12 · 1 row entry · 19 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkPrtTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkPrtTable'
G.8275.1 Port Table.
agnPtpClkPrtEntry row .1.3.6.1.4.1.164.6.2.52.4.12.1
An entry in the table.
Indexes
Column Syntax OID
This object indicates the Idx of the ptp-port.
Integer32
Constraints:
range: 1-2147483647
.1.3.6.1.4.1.164.6.2.52.4.12.1.1
This object indicates the Svi Id to which the ptp-port
is associated to.
Integer32r/w
Constraints:
range: 1-2147483647
.1.3.6.1.4.1.164.6.2.52.4.12.1.2
This object indicates the IfIndex of the entity to which the
SVI associated to.
Integer32r/w
Constraints:
range: 1-2147483647
.1.3.6.1.4.1.164.6.2.52.4.12.1.3
This object indicates local priority of the ptp-port
default value is 128.
Integer32r/w
Constraints:
range: 1-255
.1.3.6.1.4.1.164.6.2.52.4.12.1.4
This object indicates clock signal Assymetry, in nano-seconds
default value is 0.
Integer32r/w
Constraints:
range: -134217727-134217727
.1.3.6.1.4.1.164.6.2.52.4.12.1.5
This object indicates the ptp-port configured state.
Enumerationr/w
Enumerated Values:
1master
2slave
3auto
4autoNotSlave
.1.3.6.1.4.1.164.6.2.52.4.12.1.6
This object indicates the ptp-port actual state.
Enumeration
Enumerated Values:
1master
2slave
3auto
4autoNotSlave
5passive
.1.3.6.1.4.1.164.6.2.52.4.12.1.7
This object indicates the ptp-port MAC Address.
SNMPv2-TCMacAddressr/w
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
.1.3.6.1.4.1.164.6.2.52.4.12.1.8
This object indicates Clock Class.
In case the ptp-port actual state is 'Master'- this object will indicate
transmitted Clock Class.
In case the ptp-port actual state is 'Slave'- this object will indicate
received Clock…
Enumerationr/w
Enumerated Values:
6tgmPrtcLocked
7tgmHoldoverWithinSpec
135tbcHoldoverWithinSpec
140tgmHoldoverOutOfSpecTraceableToCategory1
145tbcHoldoverOutOfSpecPrior201407
150tgmHoldoverOutOfSpecTraceableToCategory2
160tgmHoldoverOutOfSpecTraceableToCategory3
165tbcHoldoverOutOfSpec
248tgmTbcNoTimeReference
.1.3.6.1.4.1.164.6.2.52.4.12.1.9
This object indicates Clock Accuarcy.
In case the ptp-port actual state is 'Master'- this object will indicate
transmitted Clock Accuracy.
In case the ptp-port actual state is 'Slave'- this object will indicate
received…
Enumerationr/w
Enumerated Values:
1r0x21
2r0xFe
.1.3.6.1.4.1.164.6.2.52.4.12.1.10
This object indicates Clock Offset Scaled Variance.
In case the ptp-port actual state is 'Master'- this object will indicate
transmitted Clock offset scaled variance.
In case the ptp-port actual state is 'Slave'- this o…
Enumerationr/w
Enumerated Values:
1r0x4E5D
2r0xFFFF
.1.3.6.1.4.1.164.6.2.52.4.12.1.11
This object indicates Clock Identity.
In case the ptp-port actual state is 'Master'- this object will indicate
transmitted Clock Identity.
In case the ptp-port actual state is 'Slave'- this object will indicate
transmit…
OctetStringr/w .1.3.6.1.4.1.164.6.2.52.4.12.1.12
This object indicates the Announce Rate of the packets,
which are transmitted or received through this port.
Enumerationr/w
Enumerated Values:
1notApplicable
2r32pps
3r64pps
4r128pps
5r16pps
6r8pps
.1.3.6.1.4.1.164.6.2.52.4.12.1.13
This object indicates the Sync Rate of the packets,
which are transmitted or received through this port.
Enumerationr/w
Enumerated Values:
1notApplicable
2r32pps
3r64pps
4r128pps
5r16pps
6r8pps
.1.3.6.1.4.1.164.6.2.52.4.12.1.14
This object indicates the Delay Rate of the packets,
which are transmitted or received through this port.
Enumerationr/w
Enumerated Values:
1notApplicable
2r32pps
3r64pps
4r128pps
5r16pps
6r8pps
.1.3.6.1.4.1.164.6.2.52.4.12.1.15
This object enables creation and deletion of entries
in the agnPtpClkPrtTable.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.164.6.2.52.4.12.1.16
This object is relevant for ptp-Port associated to Slave entity only.
This object indicates received source port identity, as it is received
in 1588 messages.
SNMP-FRAMEWORK-MIBSnmpAdminString
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.52.4.12.1.17
This object is relevant for ptp-Port associated to Slave entity only.
This object indicates received source port identity, as it is received
in 1588 announce messages only.
OctetString .1.3.6.1.4.1.164.6.2.52.4.12.1.18
The frequencyTraceable flag may be traceable or notTraceable,
depending on the availability of a PRC-tracable physical
layer frequency input signal.
Enumerationr/w
Enumerated Values:
1notApplicable
2traceable
3notTraceable
.1.3.6.1.4.1.164.6.2.52.4.12.1.19
.1.3.6.1.4.1.164.6.2.52.4.13 · 1 row entry · 10 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk agnPtpClkPrtCounterTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::agnPtpClkPrtCounterTable'
The table contains counters for Hop by Hop Cloclc Ports
(G.8275.1) .
agnPtpClkPrtCounterEntry row .1.3.6.1.4.1.164.6.2.52.4.13.1
An entry in the Table.
Column Syntax OID
This object indicates the Idx of the ptp-port.
Integer32
Constraints:
range: 1-2147483647
.1.3.6.1.4.1.164.6.2.52.4.13.1.1
Setting this object to on, will enforce a clear statistics
counters. The command will clear statistics from all
agnPtpClkPrtCounterTable.
Upon completion, the value will automatically change to off(2).
Default=off(2).
Enumerationr/w
Enumerated Values:
2off
3on
.1.3.6.1.4.1.164.6.2.52.4.13.1.2
The sum of Announce packets transmitted by the port.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.13.1.3
The sum of Announce packets received by the port.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.13.1.4
The sum of Sync packets transmitted by the port.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.13.1.5
The sum of Sync packets received by the port.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.13.1.6
The sum of Delay Request packets transmitted by the port.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.13.1.7
The sum of Delay Response packets transmitted by the port.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.13.1.8
The sum of Delay Request packets received by the port.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.13.1.9
The sum of Delay Response packets received by the port.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
.1.3.6.1.4.1.164.6.2.52.4.13.1.10
.1.3.6.1.4.1.164.6.2.52.5.1 · 1 row entry · 21 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk csmDomainTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::csmDomainTable'
Clock Selection Module (CSM) Table.
csmDomainEntry row .1.3.6.1.4.1.164.6.2.52.5.1.1
An entry in the table.
Indexes
Column Syntax OID
This is the unique Clock Selection Module Domain index.
Unsigned32
Constraints:
range: 1-4294967295
.1.3.6.1.4.1.164.6.2.52.5.1.1.1
This object enables creation and deletion of entries
in the csmDomainTable.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.164.6.2.52.5.1.1.2
This object determines Clock Selection operational mode.
auto = CSM automatically selects the Clock Source.
In this mode, CSM can be configured to work in the csmDomainQlMode
Enabled or Disabled.
freeRun = the Internal …
Enumerationr/w
Enumerated Values:
2auto
3freeRun
4forceT0Holdover
.1.3.6.1.4.1.164.6.2.52.5.1.1.3
This object determines the QL (quality) mode.

enable = clock selection is done according to quality of the clock sources.
For clock sources having same quality, priority determines selection.
Enumerationr/w
Enumerated Values:
2disable
3enable
.1.3.6.1.4.1.164.6.2.52.5.1.1.4
This object determines the network synchronization type applicable to
geographic area.
Each type has possible quality levels (csmDomainCurrentSourceQl).
Upon changing a type value, Agent will delete all the clock sourc…
Enumerationr/w
Enumerated Values:
1type1
2type2
3type3
.1.3.6.1.4.1.164.6.2.52.5.1.1.5
This object determines the minimum Quality Level(QL) of the clock
which is sent out via station clock connector.
QL value is Set according to the defined type in csmDomainSynchNetType.
Applicable only when device contai…
Enumerationr/w
Enumerated Values:
1type1Prc
2type1SsuA
3type1SsuB
4type1Sec
5type1Dnu
6type1SsmBased
21type2Prs
22type2Stu
23type2St2
24type2Tnc
25type2St3e
26type2St3
27type2Smc
28type2St4
29type2Dus
30type2SsmBased
31type2Prov
41type3Unk
42type3Sec
43type3Dnu
44type3SsmBased
.1.3.6.1.4.1.164.6.2.52.5.1.1.6
An external command .
forced - It will override the currently clock source.
csmDomainExtCmdParam determines the desired clock source.
This clock source will be selected.
This override is applicable until device reset or…
Enumerationr/w
Enumerated Values:
2off
3forced
4manual
5clear
.1.3.6.1.4.1.164.6.2.52.5.1.1.7
This object determines the required clock source number when
csmDomainExternalCmd is set to forced(3) or manual(4).
When 'forced' value is Set, CSM will switch the clock source
to csmDomainExtCmdParam always.
When 'manu…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.1.1.8
Setting this object to on, will enforce a clear operation of CSM
statistics Counters. The command will clear statistics from all
sources in csmSourceTable.
Upon completion, the value will automatically change to off(2).…
Enumerationr/w
Enumerated Values:
2off
3on
.1.3.6.1.4.1.164.6.2.52.5.1.1.9
System Clock Source ID.
0 = Source Clock is internal.
Max value is Max number of existing Clock sources.
For standard projects Max number of clock sources is 8,
and for non standard projects it is project dependent.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.1.1.10
The actual QL of csmDomainCurrentSourceId dependent on
csmDomainSynchNetType.
Enumeration
Enumerated Values:
1type1Prc
2type1SsuA
3type1SsuB
4type1Sec
5type1Dnu
6type1SsmBased
21type2Prs
22type2Stu
23type2St2
24type2Tnc
25type2St3e
26type2St3
27type2Smc
28type2St4
29type2Dus
30type2SsmBased
31type2Prov
41type3Unk
42type3Sec
43type3Dnu
44type3SsmBased
.1.3.6.1.4.1.164.6.2.52.5.1.1.11
The Clock Source ID, which is sent out via station clock connector.
When equals 0, clock Source is internal.
Applicable only when device contains station clock connector.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.1.1.12
The system selected clock source state.
freeRun - internal clock is in use.
holdover - incoming reference is in signal fail state (SSF = true).
locked - incoming reference is not in the signal fail state
(SSF = false) a…
Enumeration
Enumerated Values:
1freeRun
2holdover
3locked
.1.3.6.1.4.1.164.6.2.52.5.1.1.13
The state of the Clock Source, which is sent out via station
clock connector.
locked - incoming reference to station clock is not in the signal
fail state (SSF = false) and the quality level of the incoming reference
is…
Enumeration
Enumerated Values:
2unlocked
3locked
.1.3.6.1.4.1.164.6.2.52.5.1.1.14
The state of the Force Switch.
active - The Force Switch action is active
inActive - The Force Switch action is not active.
Enumeration
Enumerated Values:
2active
3inActive
.1.3.6.1.4.1.164.6.2.52.5.1.1.15
The state of the Manual Switch.
active - The Manual Switch action is active
inActive - The Manual Switch action is not active.
Enumeration
Enumerated Values:
2active
3inActive
.1.3.6.1.4.1.164.6.2.52.5.1.1.16
Ensure that t0 and t4 are derived from the same source (in case t4 is
not driven from external source while t0 is).
Enumerationr/w
Enumerated Values:
2off
3on
.1.3.6.1.4.1.164.6.2.52.5.1.1.17
This is the frequency deviation threshold. If the actual input clock
frequency deviation exceeds this threshold, the given synchronization
source is disqualified and the synchronization signal fail (SSF) is
generated b…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.1.1.18
The description of the domain
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Type Constraints:
range: 0..255
.1.3.6.1.4.1.164.6.2.52.5.1.1.19
Reason of the last system source clock switch.
(1) Other
(2) Manual Switch Command
(3) Force Switch Command
(4) Invalid Clock
(5) Better Clock Availability
(255) Not Applicable
Enumeration
Enumerated Values:
1other
2manualSwitchCommand
3forceSwitchCommand
4invalidClock
5betterClockAvailability
255notApplicable
.1.3.6.1.4.1.164.6.2.52.5.1.1.20
Reason of the last station source clock switch.
(1) Other
(2) Manual Switch Command
(3) Force Switch Command
(4) Invalid Clock
(5) Better Clock Availability
(255) Not Applicable
Enumeration
Enumerated Values:
1other
2manualSwitchCommand
3forceSwitchCommand
4invalidClock
5betterClockAvailability
255notApplicable
.1.3.6.1.4.1.164.6.2.52.5.1.1.21
.1.3.6.1.4.1.164.6.2.52.5.2 · 1 row entry · 20 columns
Uses the rad variant from /opt/observium/mibs/rad.
Command help
Walk csmSourceTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'RAD-Clock-MIB' -M '/opt/observium/mibs/rad:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'RAD-Clock-MIB::csmSourceTable'
CSM Clock Sources Table.
csmSourceEntry row .1.3.6.1.4.1.164.6.2.52.5.2.1
An entry in the table.
Column Syntax OID
This is the unique CSM Domain index
that the current clock source is referenced to.
Unsigned32
Constraints:
range: 1-4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.1
CSM Source running index.
For standard projects Max number of clock sources is 8,
and for non standard projects it is project dependent.
Unsigned32
Constraints:
range: 1-4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.2
This object enables creation and deletion of entries
in the csmSourceTable.
It will not be possible to add entries with csmSourceDomainIdx
that doesn't exist in csmDomainTable.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.164.6.2.52.5.2.1.3
Source type.
Enumerationr/w
Enumerated Values:
1rxPort
2station
3recovered
4adaptive
5domain
6internalGps
.1.3.6.1.4.1.164.6.2.52.5.2.1.4
ID of the clock source.
ID depends on type as follows:
rxPort - ifIndex of the interface configured for the csmSourceIdx.
station - Station ID.
recovered - Recovered ID (agnClkSrcPortIdx when
agnClkSrcPortSr…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.5
The configured quality level of csmSourceIdx.
Default= ssmBased (type1SsmBased(6)/type2SsmBased(30)/type3SsmBased(43))
according to the type (csmDomainSynchNetType from csmDomainTable)
of the domain that this clock sour…
Enumerationr/w
Enumerated Values:
1type1Prc
2type1SsuA
3type1SsuB
4type1Sec
5type1Dnu
6type1SsmBased
21type2Prs
22type2Stu
23type2St2
24type2Tnc
25type2St3e
26type2St3
27type2Smc
28type2St4
29type2Dus
30type2SsmBased
31type2Prov
41type3Unk
42type3Sec
43type3Dnu
44type3SsmBased
.1.3.6.1.4.1.164.6.2.52.5.2.1.6
The configured priority. Priority will be used for source selection
when the Quality Levels of the clock sources cannot be used (for example
when Quality Level of some clock sources are equal or when
csmDomainQlMode = d…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.7
Holdoff Timer in msec.
When Holdoff Timer>0, and the current clock source fails (SSF),
timer is started and doesn't trigger the CSM immediately to switch to
another clock source.
In this case, when Holdoff Timer expired…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.8
Wait to Restore (WTR) time in msec.
After failed clock source recovers, in order to prevent frequent
clock source switchings of the CSM due to intermittent defects,
a period of time will pass before
CSM will return to t…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.9
Setting this object to on, will clear WTR, causing immediate
return to recovered source.
Upon completion, the value will automatically change to off(2).
Default=off(2).
After operation is performed, value of csmSourceWt…
Enumerationr/w
Enumerated Values:
2off
3on
.1.3.6.1.4.1.164.6.2.52.5.2.1.10
Clock Source Status.
physicalFail(2)- Physical interface failure.
monitoringFail(3)- Clock Selection HW failure (SSF = true).
esmcFail(4)- Fail report received via ESMC protocol.
Enumeration
Enumerated Values:
1ok
2physicalFail
3monitoringFail
4esmcFail
.1.3.6.1.4.1.164.6.2.52.5.2.1.11
The reported Quality Level(QL)from Clock Selection Module(CSM)
to Clock Source.
Enumeration
Enumerated Values:
1type1Prc
2type1SsuA
3type1SsuB
4type1Sec
5type1Dnu
6type1SsmBased
21type2Prs
22type2Stu
23type2St2
24type2Tnc
25type2St3e
26type2St3
27type2Smc
28type2St4
29type2Dus
30type2SsmBased
31type2Prov
41type3Unk
42type3Sec
43type3Dnu
44type3SsmBased
.1.3.6.1.4.1.164.6.2.52.5.2.1.12
The reported Quality Level(QL)Clock Source to Clock Selection Module.
Enumeration
Enumerated Values:
1type1Prc
2type1SsuA
3type1SsuB
4type1Sec
5type1Dnu
6type1SsmBased
21type2Prs
22type2Stu
23type2St2
24type2Tnc
25type2St3e
26type2St3
27type2Smc
28type2St4
29type2Dus
30type2SsmBased
31type2Prov
41type3Unk
42type3Sec
43type3Dnu
44type3SsmBased
.1.3.6.1.4.1.164.6.2.52.5.2.1.13
ESMC Protocol state.
unlock - Messages are not received as expected.
lock- OK.
Applicable only for Ethernet interfaces.
Enumeration
Enumerated Values:
2unlock
3lock
.1.3.6.1.4.1.164.6.2.52.5.2.1.14
Number of informational ESMC messages sent from Clock Selection
Module(CSM) to Clock Source.
Applicable only for Ethernet interfaces.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.15
Number of informational ESMC messages received by Clock
Selection Module(CSM) .
Applicable only for Ethernet interfaces.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.16
Number of times that ESMC messages were not received as expected.
Applicable only for Ethernet interfaces.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.17
Number of ESMC messages that report status change of the clock source
(csmSourceStatus) that were sent from Clock Selection Module(CSM)
to Clock Source.
Applicable only for Ethernet interfaces.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.18
Number of ESMC messages that report status change of the clock source
(csmSourceStatus) that were received by Clock Selection Module(CSM).
Applicable only for Ethernet interfaces.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.19
Wait to restore state.
Use the number (2) to indicate 'running' state,
Use the number (3) to indicate 'inactive' state,
All other numbers can be use to indicate the current WTR time.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.164.6.2.52.5.2.1.20