MX-CORNET-SYSTEM-MIB Table View

This table holds the actual configuration used by the lines to register with a
CorNet PBX.

ipAddressStatusCorNetPbxIfEntry row .1.3.6.1.4.1.4935.10.1.130.10.1

Each row holds the IP address and the CorNet signaling port of a CorNet PBX. The
line is actually using this configuration to register with a CorNet PBX.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
ipAddressStatusCorNetPbxHost The IP address or domain name of the CorNet PBX to which the line is configured to register.	MX-TCMxIpHostName Type Constraints: range: 0..255	.1.3.6.1.4.1.4935.10.1.130.10.1.10
ipAddressStatusCorNetPbxPort The CorNet signaling port of the CorNet PBX to which the line is configured to register.	MX-TCMxIpPort Type Constraints: range: 1..65535	.1.3.6.1.4.1.4935.10.1.130.10.1.20

This table holds the configuration for the registration of the lines with a
CorNet PBX.

ipAddressConfigCorNetPbxIfEntry row .1.3.6.1.4.1.4935.15.1.130.10.10.1

Each row is used to configure the IP address and the CorNet signaling port of a
CorNet PBX. The line uses this configuration to register with a CorNet PBX.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
ipAddressConfigCorNetPbxHost The IP address or domain name of the CorNet PBX to which the line registers.	MX-TCMxIpHostNamer/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4935.15.1.130.10.10.1.10
ipAddressConfigCorNetPbxPort The CorNet signaling port used by the CorNet PBX.	MX-TCMxIpPortr/w Type Constraints: range: 1..65535	.1.3.6.1.4.1.4935.15.1.130.10.10.1.20

This table holds configuration for the registration of CorNet units. Each row
is used to configure a single line of the unit.

corNetSystemRegistrationIfEntry row .1.3.6.1.4.1.4935.20.40.1.1.10.10.1

Each row is used to configure the registration of a single line.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
corNetSystemRegSubscriberNumber The E.164 alias of the line. Each line must be configured with a unique Subscriber Number. The Subscriber Number can?t be left empty. The line of the CorNet unit provides its Subscriber Number to the CorN…	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.4935.20.40.1.1.10.10.1.10
corNetSystemRegLocationIdentifierNumber The Location Identifier Number describes the physical location of the CorNet unit line. The CorNet PBX uses this information to route emergency calls. The Location Identification Number may be left empty. …	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.4935.20.40.1.1.10.10.1.20

This table holds configuration for the initialization of CorNet units. Each row
is used to configure a single line of the unit.

corNetSystemInitializationIfEntry row .1.3.6.1.4.1.4935.20.40.1.1.20.10.1

Each row is used to configure the initialization of a single line.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
corNetSystemInitEmergencyNumber The Emergency Number is used by the CorNet PBX to route emergency calls. The Emergency Number may be left empty. The line provides its Emergency Number to the CorNet PBX during the initialization process.…	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.4935.20.40.1.1.20.10.1.10

This table holds the configuration for the security of CorNet units. Each row
is used to configure a single line of the unit.

corNetSystemSecurityIfEntry row .1.3.6.1.4.1.4935.20.40.1.1.25.10.1

Each row is used to configure the security of a single line.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
corNetSystemSecurityPassword The security password used by an endpoint. The security is used in: - Authentication of CorNet registration. - Message integrity of CorNet signaling. - H.235 security in H.323 signaling. …	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.4935.20.40.1.1.25.10.1.10
corNetSystemSecurityLevel The security level used by an endpoint: none (0): The endpoint doesn't use security. reduced (1): The endpoint uses the reduced security profile. In this profile, the endpoint uses authenti…	Enumerationr/w Enumerated Values: 0 none 1 reduced 2 full	.1.3.6.1.4.1.4935.20.40.1.1.25.10.1.50

This table holds the configuration for the data of CorNet units. Each row
is used to configure a single line of the unit.

corNetSystemDataIfEntry row .1.3.6.1.4.1.4935.20.40.1.1.50.10.1

Each row is used to configure the data of a single line.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
corNetSystemDataRfc2198RedundancyLevel Sets the redundancy level used in the RFC 2198. This variable is used to duplicate the RFC 2833 fax/modem tones.	Unsigned32r/w Constraints: range: 0-5	.1.3.6.1.4.1.4935.20.40.1.1.50.10.1.50
corNetSystemDataRfc2198DefaultPayloadType Default payload type used for RFC 2198. This payload type is applied for both receiving and sending packets. The RFC 2198 is only enable if: 1) The RFC 2833 is enabled. The redundancy is only applied to…	Unsigned32r/w Constraints: range: 96-127	.1.3.6.1.4.1.4935.20.40.1.1.50.10.1.70
corNetSystemDataRfc2833DefaultPayloadType This variable sets the payload type of the RFC 2833 events that is supported by the unit. This value will be inserted in the dynamicRTPPayloadType field in the H.225 TerminalCapabilitySet message. For ex…	Unsigned32r/w Constraints: range: 96-127	.1.3.6.1.4.1.4935.20.40.1.1.50.10.1.90
corNetSystemDataVoiceOnlyModeEnable This variable defines whether the fax/modem tone is detected or not. enable: Fax/Modem tones will not be detected (voice only); disable: Fax/Modem tones will be detected (voice/fax/modem).	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.1.3.6.1.4.1.4935.20.40.1.1.50.10.1.150

This table holds the parameters defining access to the services offered
by the CorNet gatekeeper, indexed by service entry number.
          
Note that these services are only recognized when the
corNetSystemCallFeaturesEnable variable is enabled.

corNetSystemServicesEntry row .1.3.6.1.4.1.4935.20.40.1.1.100.100.1

Each row is used to configure a single service.

Indexes

corNetSystemServicesIndex

Column	Syntax	OID
corNetSystemServicesIndex Accepted service index for this row.	Unsigned32 Constraints: range: 1-10	.1.3.6.1.4.1.4935.20.40.1.1.100.100.1.5
corNetSystemServiceName A character string identifying the service. Only used for display purposes in the configuration interface.	OctetStringr/w Constraints: range: 0-127	.1.3.6.1.4.1.4935.20.40.1.1.100.100.1.10
corNetSystemServiceEnable Used to activate/deactivate the corresponding service.	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.1.3.6.1.4.1.4935.20.40.1.1.100.100.1.15
corNetSystemServiceKbKeyCode The feature code identifying the service in the CorNet server.	Unsigned32r/w Constraints: range: 0-63	.1.3.6.1.4.1.4935.20.40.1.1.100.100.1.20
corNetSystemServiceActivationSequence A string making up a digit map that the user needs to dial when requesting the service. The formal digit map syntax, as summarized here, is taken from RFC 2705: DigitMap = DigitString / '(' DigitStringLi…	OctetStringr/w Constraints: range: 0-63	.1.3.6.1.4.1.4935.20.40.1.1.100.100.1.25
corNetSystemService2StageFlag The boolean flag used to distinguish between the services that only require the user to enter the activation sequence and those which necessitate further dialling from the user once the server has responded to the servi…	Enumerationr/w Enumerated Values: 0 no 1 yes	.1.3.6.1.4.1.4935.20.40.1.1.100.100.1.30
corNetSystemServiceFirstDigitTimer Applies to the second stage of two-stage services. This is the amount of time to wait (in milliseconds) for user input while in the second stage of a service request. If the delay expires, the service request is cancel…	Unsigned32r/w Constraints: range: 1000-180000	.1.3.6.1.4.1.4935.20.40.1.1.100.100.1.35