LUM-IFOPTICAL-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
6
Rows
6
Columns
101

ifOpticalTransSectionTable

table
.1.3.6.1.4.1.8708.2.48.2.2.1 · 1 row entry · 20 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk ifOpticalTransSectionTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-IFOPTICAL-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-IFOPTICAL-MIB::ifOpticalTransSectionTable' 
The if optical transmission section interface list.
ifOpticalTransSectionEntry row .1.3.6.1.4.1.8708.2.48.2.2.1.1
An entry in the ifOptical transmission section list.
Indexes
Column Syntax OID
ifOpticalTransSectionIndex
An index assigned to each entry.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.1
ifOpticalTransSectionName
The management name of the optical transmission section,
for example 'ots:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.
LUM-TCMgmtNameStringr/w
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.2
ifOpticalTransSectionConnIfBasicIfIndex
An index describing to which index in ifBasicIf table
this object is related to.
LUM-TCUnsigned32WithNAr/w
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.3
ifOpticalTransSectionForwardAls
Forward Automatic Laser Shut-down. Decides if
laser shutdown of the client should occur when
a defect on the line or remote client is detected.

disabled - The laser is NOT turned off at defect
detection.
…
LUM-TCEnabledDisabledWithNAr/w
Type Values:
1disabled
2enabled
2147483647notApplicable
Description:
disabled - Attribute is not set.

enabled - Attribute is set.

notApplicable (2147483647) is used when attribute is
not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.4
ifOpticalTransSectionRxPowerLevel
The received power level in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.5
ifOpticalTransSectionRxPowerLevelLowRelativeThld
The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity.
LUM-TCSigned32WithNA
Constraints:
range: -50-100
range: 2147483646-2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.6
ifOpticalTransSectionTxPowerLevel
The transmitted power level in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.7
ifOpticalTransSectionLaserMode
The administrative state of the TX-side laser.

als - Automatic Laser Shutdown/Turn-Off
when lossOfSignal is detected on the RX side.

forcedOn - Laser is on even if lossOfSignal is
active on…
LUM-TCLaserModer/w
Type Values:
1forcedOn
2als
2147483647notApplicable
Description:
The configured laser mode.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.8
ifOpticalTransSectionLaserStatus
The actual state of the TX-side laser.

on - The laser is turned on.

off - The laser is turned off.
LUM-TCOnOff
Type Values:
1off
2on
2147483646notAvailable
2147483647notApplicable
Description:
The configured laser mode.
notApplicable - used to tell that attribute
is not used in current configuration.
notAvailable - used to tell that it is not
possible to read attribute at the moment.
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.9
ifOpticalTransSectionReceiverSensitivity
The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.10
ifOpticalTransSectionTxSignalStatus
The state for outgoing (TX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.11
ifOpticalTransSectionRxSignalStatus
The state for incoming (RX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.12
ifOpticalTransSectionLossOfSignal
Loss of signal (LOS).

The received signal has disappeared.

alarm - Loss of signal active

ok - Loss of signal is not active
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.13
ifOpticalTransSectionRxPowerLevelLow
Low Rx power.

Received power level low threshold exceeded.

Applicable for all signal formats.

alarm: The received power level is below the
associated threshold.
…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.14
ifOpticalTransSectionRxPowerLevelHigh
High Rx power.

Received power level is too high.

Applicable for all signal formats.

alarm: The received power level is too high.

ok: The received power level i…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.15
ifOpticalTransSectionRxExcessiveInputPower
Excessively high Rx power.

Received power level is excessively high.

Applicable for all signal formats.

alarm: The received power level is excessively high.

ok…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.16
ifOpticalTransSectionTxPowerLow
Low Tx power.

Transmit power is lower than the set threshold.

Applicable for all signal formats.

alarm: The transmit power level is lower than threshold.

ok: T…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.17
ifOpticalTransSectionRxPowerLevelLowAbsoluteThld
The lower threshold for received power level in
units of 0.1 dB.
LUM-TCSigned32WithNA
Constraints:
range: -300-50
range: 2147483646-2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.18
ifOpticalTransSectionLossThld
The threshold to declare LOS.
LUM-TCSigned32WithNA
Constraints:
range: -420-60
range: 2147483647-2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.19
ifOpticalTransSectionLaserForcedOn
When enabled, the laser is forced on regardless of
circumstances. Be aware that enabling this mode might
interfere with other functions and affect working traffic.
When used with Y-cable (Optical coupler) protection it …
LUM-TCEnabledDisabledWithNAr/w
Type Values:
1disabled
2enabled
2147483647notApplicable
Description:
disabled - Attribute is not set.

enabled - Attribute is set.

notApplicable (2147483647) is used when attribute is
not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.2.1.1.20

ifOpticalChannelTable

table
.1.3.6.1.4.1.8708.2.48.2.3.1 · 1 row entry · 27 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk ifOpticalChannelTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-IFOPTICAL-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-IFOPTICAL-MIB::ifOpticalChannelTable' 
The if optical channel interface list.
ifOpticalChannelEntry row .1.3.6.1.4.1.8708.2.48.2.3.1.1
An entry in the ifOptical channel list.
Indexes
Column Syntax OID
ifOpticalChannelIndex
An index assigned to each entry.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.1
ifOpticalChannelName
The management name of the optical channel,
for example 'och:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.
LUM-TCMgmtNameStringr/w
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.2
ifOpticalChannelConnIfBasicIfIndex
An index describing to which index in ifBasicIf table
this object is related to.
LUM-TCUnsigned32WithNAr/w
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.3
ifOpticalChannelTxFrequency
The transmitted frequency given in wavelength nm
or as channels.
E.g. ch871 means the frequency 187.1 THz.
w1310 means the wavelength 1310 nm.
LUM-TCFrequency
Type Values:
0undefined
130b1300
150b1500
850w850
1270w1270
1290w1290
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1530w1530
1550w1550
1570w1570
1590w1590
1610w1610
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19135ch9135
19140ch914
19145ch9145
19150ch915
19155ch9155
19160ch916
19165ch9165
19170ch917
19175ch9175
19180ch918
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
2147483646notAvailable
2147483647notApplicable
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).

notApplicable - used to tell that attribute
is not used in current configuration.

notAvailable - used to tell that it is not
…
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.4
ifOpticalChannelExpectedTxFrequency
The expected frequency given in wavelength nm
or as channels.
E.g. ch871 means the frequency 187.1 THz.
w1310 means the wavelength 1310 nm.
LUM-TCFrequencyOnlyNotApplicabler/w
Type Values:
0undefined
130b1300
150b1500
850w850
1270w1270
1290w1290
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1530w1530
1550w1550
1570w1570
1590w1590
1610w1610
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19135ch9135
19140ch914
19145ch9145
19150ch915
19155ch9155
19160ch916
19165ch9165
19170ch917
19175ch9175
19180ch918
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
2147483647notApplicable
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).

notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.5
ifOpticalChannelTxSignalStatus
The state for outgoing (TX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.6
ifOpticalChannelRxSignalStatus
The state for incoming (RX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.7
ifOpticalChannelIllegalTxFrequency
Illegal tx frequency.

The tx frequency supported by the transceiver is not
recognized by the system.

alarm: Invalid or unknown frequency information is
detected in the (pluggable) tr…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.8
ifOpticalChannelUnexpectedTxFrequency
Unexpected transmitted frequency.

The actual frequency does not match the
pre-configured frequency.

A pre-configured frequency of '0' matches
all actual frequencies.

alarm: T…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.9
ifOpticalChannelNoTxFrequencySet
No tx frequency set.

The tunable laser frequency has not been set.

alarm: Tunable laser frequency is not set.

ok: Tunable laser frequency is set.
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.10
ifOpticalChannelDispersionSearchLimit
The upper search limit for the module dispersion compensator. Medium
= 22,500 ps/nm, which corresponds to approximately 1300 km standard
fiber. High = 30,000 ps/nm, which corresponds to approximately 1700 km
standard fi…
LUM-TCDispersionSearchLimit
Type Values:
22500medium
30000high
Description:
Dispersion Search Limit.
- Medium
- High
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.11
ifOpticalChannelLaserNotTuned
Laser not tuned.

The tunable laser is not tuned to set frequency yet.
This alarm can be cleared by setting the attribute
LaserForcedOn to enabled. Note that this can disturb
traffic. See the help for Lase…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.12
ifOpticalChannelLineCoding
Line coding.

qam16 - 16QAM
dqpsk - D-QPSK
qpsk - QPSK
notApplicable - 2147483647 is used to indicate that the attribute
is not used on the board.
Enumerationr/w
Enumerated Values:
1qam16
2dqpsk
3qpsk
4qam8
2147483647notApplicable
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.13
ifOpticalChannelRxSignalPowerLevel
The received signal power level in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.14
ifOpticalChannelRxSignalPowerLevelLowRelativeThld
The lower threshold for received signal power level in
units of 0.1 dB, relative to the receiver
sensitivity.
LUM-TCSigned32WithNA
Constraints:
range: -50-100
range: 2147483646-2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.15
ifOpticalChannelRxSignalPowerLevelLow
Low Rx signal power.

Received signal power level low threshold exceeded.

Applicable for all signal formats.

alarm: The received signal power level is below the
associated thr…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.16
ifOpticalChannelRxSignalPowerLevelHigh
High Rx signal power.

Received signal power level high threshold exceeded.

Applicable for all signal formats.

alarm: The received signal power level is over the
associated th…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.17
ifOpticalChannelRxSignalPowerSensitivity
The lowest signal power that the receiver is guaranteed
to handle, in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.18
ifOpticalChannelAutoLambdaState
The Auto Lambda state of the TRX.

none - Inserted TRX does not support auto lambda
notApplicable - Interface does not support auto lambda or TRX is not inserted
searching - Searching auto …
LUM-TCAutoLambdaState
Type Values:
0none
1notApplicable
2searching
3locked
Description:
Defines the auto lambda state of the TRX

none - Inserted TRX does not support auto lambda
notApplicable - Interface does not support auto lambda or TRX is not inserted
searching - Searching au…
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.19
ifOpticalChannelWantedTxSignalPowerLevel
The wanted signal power level in units of 0.1 dBm.
LUM-TCSigned32WithNAr/w
Constraints:
range: -150-10
range: 2147483646-2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.20
ifOpticalChannelActualTxSignalPowerLevel
The actual signal power level in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.21
ifOpticalChannelMinSupportedTxSignalPowerLevel
The minimum Tx signal power level the transceiver supports in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.22
ifOpticalChannelMaxSupportedTxSignalPowerLevel
The maximum Tx signal power level the transceiver supports in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.23
ifOpticalChannelWantedTxSignalPowerLevelOutOfRange
Wanted Tx signal power level out of range.


alarm: The wanted signal power level is out of
transceiver's supported range.

ok: The wanted signal power level is within
transceiv…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.24
ifOpticalChannelTxFrequencyFlex
The transmitted flexible center frequency.
In the CLI/GUI, the value is presented in unit of THz.
In SNMP the value is represented in unit of MHz.
LUM-TCFlexibleCenterFrequencyRangeWithNA
Type Constraints:
range: 0
range: 191350000..196100000
range: 2147483646..2147483647
Description:
Flexible center frequency range.
0 signifies an undefined flexible frequency
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.25
ifOpticalChannelExpectedTxFrequencyFlex
The expected flexible center frequency.
In the CLI/GUI, the value is presented in unit of THz.
In SNMP the value is represented in unit of MHz.

0 : signifies an undefined flexible frequency.
LUM-TCFlexibleCenterFrequencyRangeWithNAr/w
Type Constraints:
range: 0
range: 191350000..196100000
range: 2147483646..2147483647
Description:
Flexible center frequency range.
0 signifies an undefined flexible frequency
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.26
ifOpticalChannelExpectedTxFrequencyFlexView
The expected flexible center frequency.
In the CLI/GUI, the value is presented in unit of THz.
In SNMP the value is represented in unit of MHz.

undefined : flexible frequency not set, default.
Range :…
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.48.2.3.1.1.27

ifOpticalDigitalSignalRateTable

table
.1.3.6.1.4.1.8708.2.48.2.4.1 · 1 row entry · 9 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk ifOpticalDigitalSignalRateTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-IFOPTICAL-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-IFOPTICAL-MIB::ifOpticalDigitalSignalRateTable' 
The if optical digital signal rate interface list.
ifOpticalDigitalSignalRateEntry row .1.3.6.1.4.1.8708.2.48.2.4.1.1
An entry in the ifOptical digital signal rate list.
Indexes
Column Syntax OID
ifOpticalDigitalSignalRateIndex
An index assigned to each entry.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.48.2.4.1.1.1
ifOpticalDigitalSignalRateName
The management name of the optical channel,
for example 'dsr:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.
LUM-TCMgmtNameString
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.48.2.4.1.1.2
ifOpticalDigitalSignalRateConnIfBasicIfIndex
An index describing to which index in ifBasicIf table
this object is related to.
LUM-TCUnsigned32WithNA
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.48.2.4.1.1.3
ifOpticalDigitalSignalRateMaxBitRate
The max signal bit rate in units of
1,000 000 bits (mb) per second.
LUM-TCUnsigned32WithNA
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.48.2.4.1.1.5
ifOpticalDigitalSignalRateMinBitRate
The min signal bit rate in units of
1,000 000 bits (mb) per second.
LUM-TCUnsigned32WithNA
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.48.2.4.1.1.6
ifOpticalDigitalSignalRateTxSignalStatus
The state for outgoing (TX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.4.1.1.7
ifOpticalDigitalSignalRateRxSignalStatus
The state for incoming (RX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.4.1.1.8
ifOpticalDigitalSignalRateLossOfLock
Loss of lock.

The receiver could not lock to the rate of the incoming signal.

alarm: The signal could not be locked.

ok: The signal could be locked.
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.4.1.1.9
ifOpticalDigitalSignalRateBitrateUnavailable
Bitrate unavailable.

The inserted transceiver does not support the
requested bit rate.

alarm: A transceiver with other supported bit rate than
the requested bit rate is inserted.
…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.4.1.1.10

ifOpticalFecTable

table
.1.3.6.1.4.1.8708.2.48.2.5.1 · 1 row entry · 12 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk ifOpticalFecTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-IFOPTICAL-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-IFOPTICAL-MIB::ifOpticalFecTable' 
The if optical Fec list.
ifOpticalFecEntry row .1.3.6.1.4.1.8708.2.48.2.5.1.1
An entry in the ifOptical Fec list.
Indexes
Column Syntax OID
ifOpticalFecIndex
An index assigned to each entry.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.1
ifOpticalFecName
The management name of the FEC object,
for example 'lineFec:1:2:1-2', where the first number
indicates subrack, the second slot number and the
third/fourth are the physical port numbers.
LUM-TCMgmtNameStringr/w
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.2
ifOpticalFecConnIfBasicIfIndex
An index describing to which index in ifBasicIf table
this object is related to.
LUM-TCUnsigned32WithNAr/w
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.3
ifOpticalFecType
Set type of FEC.

g709 - 1st generation FEC according to
ITU-T G.709 (near 6 dB coding gain).

g9751I4 - FEC according to G975.1 I.4. Outer code: RS(1023,1007),
Inner code:…
LUM-TCFecTyper/w
Type Values:
0disabled
1g709
2g9751I4
3g9751I7
4sdFec
5oFec
6cFec
2147483647notApplicable
Description:
Defines the FEC type of the signal.

disabled - FEC correction is not activated.

g709 - 1st generation FEC according to
ITU-T G.709 (near 6 dB coding gain).

g9751I4 - …
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.4
ifOpticalFecTxSignalStatus
The state for outgoing (TX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.5
ifOpticalFecRxSignalStatus
The state for incoming (RX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.6
ifOpticalFecFailure
FEC failure.

Too many errors to get valid FEC statistics. It is not
possible to run control loops based on FEC statistics.

A: Too many errors to get valid FEC statistics.

D:…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.7
ifOpticalFecSignalDegraded
Signal degraded (SD).

Too many error corrected. If more errors are corrected
it might effect the client signal in a negative way.
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.8
ifOpticalFecSignalDegradeThreshold
Threshold for signal degraded alarm,
based on BER value.

Predefined levels

rxBerLevel1 = 1E-12
rxBerLevel2 = 1E-13
rxBerLevel3 = 1E-15

OSNRMargin1 = 0.5 dB margin with respec…
LUM-TCBerLevelMTOSIr/w
Type Values:
1qMargin1
2qMargin2
5osnrMargin1
10osnrMargin2
12rxBerLevel1
13rxBerLevel2
15rxBerLevel3
Description:
Predefined levels for signal degraded alarm

rxBerLevel1 = 1E-12
rxBerLevel2 = 1E-13
rxBerLevel3 = 1E-15

OSNRMargin1 = 0.5 dB margin with respect to FEC cliff
OSNRMargin2 = 1.0 dB margin with respec…
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.9
ifOpticalFecTypeUnavailable
Fec type unavailable.

The inserted transceiver does not support the
requested fec type.

alarm: A transceiver with other supported fec type
than the requested bit rate is inserted.
…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.10
ifOpticalFecUId
Unique Identifier for the entry
Unsigned32r/w
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.11
ifOpticalFecDecModeMismatch
FEC decoding mode mismatch.
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.5.1.1.12

ifOpticalTransLaneCarrierTable

table
.1.3.6.1.4.1.8708.2.48.2.6.1 · 1 row entry · 14 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk ifOpticalTransLaneCarrierTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-IFOPTICAL-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-IFOPTICAL-MIB::ifOpticalTransLaneCarrierTable' 
The if optical transport lane carrier list.
Structure and nomenclature in table is derived
from G.709 fig. 7-1B
ifOpticalTransLaneCarrierEntry row .1.3.6.1.4.1.8708.2.48.2.6.1.1
An entry in the ifOptical transport lane carrier list.
Indexes
Column Syntax OID
ifOpticalTransLaneCarrierIndex
An index assigned to each entry.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.1
ifOpticalTransLaneCarrierName
The management name of the OTLC object,
for example 'lineOtlc:1:2:1-2:1', where the first number
indicates subrack, the second slot number, the
third/fourth are the physical port numbers and the last is lane number.
LUM-TCMgmtNameString
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.2
ifOpticalTransLaneCarrierConnIfBasicIfIndex
An index describing to which index in ifBasicIf table
this object is related to.
LUM-TCUnsigned32WithNA
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.3
ifOpticalTransLaneCarrierConnIfOpticalTransLaneCarrierGrIndex
An index describing to which index in ifOpticalTransLaneCarrierGroup table
this object is related to.
LUM-TCUnsigned32WithNA
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.4
ifOpticalTransLaneCarrierLaneId
Lane number.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.5
ifOpticalTransLaneCarrierTxSignalStatus
The state for outgoing (TX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.6
ifOpticalTransLaneCarrierRxSignalStatus
The state for incoming (RX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.7
ifOpticalTransLaneCarrierRxPowerLevel
The received power level in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.8
ifOpticalTransLaneCarrierLossOfSignal
Loss of signal (LOS).

The received signal has disappeared.

alarm - Loss Of Signal active

ok - Loss of signal is not active
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.9
ifOpticalTransLaneCarrierReceiverSensitivity
The lowest power that the receiver is guaranteed
to handle, per lane, in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.10
ifOpticalTransLaneCarrierRxPowerLevelLow
Low Rx power.

Received power level low threshold exceeded.
Relative to the threshold in the OTLCG table
(Lane sensitivity + threshold).

Applicable for all signal formats.

ala…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.11
ifOpticalTransLaneCarrierTxFrequency
The transmitted frequency given in wavelength nm
or as channels.
E.g. ch871 means the frequency 187.1 THz.
w1310 means the wavelength 1310 nm.
LUM-TCLaneFrequency
Type Values:
0undefined
130b1300
150b1500
850w850
1270w1270
1290w1290
1297w1297
1301w1301
1305w1305
1309w1309
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1523w1523
1530w1530
1531w1531
1539w1539
1547w1547
1550w1550
1555w1555
1563w1563
1570w1570
1571w1571
1579w1579
1587w1587
1590w1590
1595w1595
1610w1610
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
2147483646notAvailable
2147483647notApplicable
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).

notApplicable - used to tell that attribute
is not used in current configuration.

notAvailable - used to tell that it is not
…
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.12
ifOpticalTransLaneCarrierCounterSes
Severely Errored Seconds.
The counter associated with the number of
errored seconds (seconds with LOS) in the interval per lane.
LUM-TCUnsigned32WithNA
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.13
ifOpticalTransLaneCarrierCounterSesResetdeprecated
Reset SES Counter.
After a successful reset the default value
(normal) is restored in this attribute.
LUM-TCResetWithNA
Type Values:
1reset
2normal
2147483647notApplicable
Description:
When the attribute is set to reset the function is
re-initialised. Then the attribute is set to normal again
automatically.
reset - Re-initialises the function
normal - The function is in normal state
notApplicable - us…
 .1.3.6.1.4.1.8708.2.48.2.6.1.1.14

ifOpticalTransLaneCarrierGroupTable

table
.1.3.6.1.4.1.8708.2.48.2.7.1 · 1 row entry · 19 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk ifOpticalTransLaneCarrierGroupTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-IFOPTICAL-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-IFOPTICAL-MIB::ifOpticalTransLaneCarrierGroupTable' 
The if optical transport lane carrier group list.
ifOpticalTransLaneCarrierGroupEntry row .1.3.6.1.4.1.8708.2.48.2.7.1.1
An entry in the ifOptical transport lane carrier group list.
Indexes
Column Syntax OID
ifOpticalTransLaneCarrierGroupIndex
An index assigned to each entry.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.1
ifOpticalTransLaneCarrierGroupName
The management name of the OTLCG object,
for example 'lineOtlcg:1:2:1-2', where the first number
indicates subrack, the second slot number, the
third/fourth are the physical port numbers.
LUM-TCMgmtNameStringr/w
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.2
ifOpticalTransLaneCarrierGroupConnIfBasicIfIndex
An index describing to which index in ifBasicIf table
this object is related to.
LUM-TCUnsigned32WithNAr/w
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.3
ifOpticalTransLaneCarrierGroupTxSignalStatus
The state for outgoing (TX) signal

of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.4
ifOpticalTransLaneCarrierGroupRxSignalStatus
The state for incoming (RX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.5
ifOpticalTransLaneCarrierGroupForwardAls
Forward Automatic Laser Shut-down. Decides if
laser shutdown of the client should occur when
a defect on the line or remote client is detected.

disabled - The laser is NOT turned off at defect
detection.
…
LUM-TCEnabledDisabledWithNAr/w
Type Values:
1disabled
2enabled
2147483647notApplicable
Description:
disabled - Attribute is not set.

enabled - Attribute is set.

notApplicable (2147483647) is used when attribute is
not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.6
ifOpticalTransLaneCarrierGroupLaserStatus
The actual state of the TX-side laser.

on - The laser is turned on.

off - The laser is turned off.
LUM-TCOnOff
Type Values:
1off
2on
2147483646notAvailable
2147483647notApplicable
Description:
The configured laser mode.
notApplicable - used to tell that attribute
is not used in current configuration.
notAvailable - used to tell that it is not
possible to read attribute at the moment.
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.7
ifOpticalTransLaneCarrierGroupTxPowerLevel
The total transmitted power level, including all lanes,
in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.8
ifOpticalTransLaneCarrierGroupRxPowerLevel
The total received power level, including all lanes,
in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.9
ifOpticalTransLaneCarrierGroupLossOfSignal
Loss of signal (LOS).

The received signal has disappeared.

alarm - Loss Of Signal active

ok - Loss of signal is not active
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.10
ifOpticalTransLaneCarrierGroupRxPowerLevelLowRelativeThld
The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity.
If multi lane transceiver is used this threshold
is used on all lanes.
LUM-TCSigned32WithNA
Constraints:
range: -50-100
range: 2147483646-2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.11
ifOpticalTransLaneCarrierGroupRxPowerLevelLow
Low Rx power.

Received power level low threshold exceeded.
If multi lane transceiver is used the threshold
is exceeded on at least one lane.

Applicable for all signal formats.
…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.12
ifOpticalTransLaneCarrierGroupTxFrequency
The transmitted frequency given in wavelength nm
or as channels, in case of multi lambda lane transciever
this is the base frequency.
E.g. ch871 means the frequency 187.1 THz.
w1310 means the wavelength 1310 nm.
LUM-TCFrequency
Type Values:
0undefined
130b1300
150b1500
850w850
1270w1270
1290w1290
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1530w1530
1550w1550
1570w1570
1590w1590
1610w1610
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19135ch9135
19140ch914
19145ch9145
19150ch915
19155ch9155
19160ch916
19165ch9165
19170ch917
19175ch9175
19180ch918
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
2147483646notAvailable
2147483647notApplicable
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).

notApplicable - used to tell that attribute
is not used in current configuration.

notAvailable - used to tell that it is not
…
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.13
ifOpticalTransLaneCarrierGroupExpectedTxFrequency
The expected frequency given in wavelength nm
or as channels.
E.g. ch871 means the frequency 187.1 THz.
w1310 means the wavelength 1310 nm.
LUM-TCFrequencyOnlyNotApplicabler/w
Type Values:
0undefined
130b1300
150b1500
850w850
1270w1270
1290w1290
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1530w1530
1550w1550
1570w1570
1590w1590
1610w1610
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19135ch9135
19140ch914
19145ch9145
19150ch915
19155ch9155
19160ch916
19165ch9165
19170ch917
19175ch9175
19180ch918
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
2147483647notApplicable
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).

notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.14
ifOpticalTransLaneCarrierGroupUnexpectedTxFrequency
Unexpected transmitted frequency.

The actual frequency does not match the
pre-configured frequency.

A pre-configured frequency of '0' matches
all actual frequencies.

alarm: T…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.15
ifOpticalTransLaneCarrierGroupIllegalTxFrequency
Illegal Tx frequency.

The tx frequency supported by the transceiver is not
recognized by the system.

alarm: Invalid or unknown frequency information is
detected in the (pluggable) tr…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.16
ifOpticalTransLaneCarrierGroupCounterSesReset
Reset SES Counter.
After a successful reset the default value
(normal) is restored in this attribute.
LUM-TCResetWithNA
Type Values:
1reset
2normal
2147483647notApplicable
Description:
When the attribute is set to reset the function is
re-initialised. Then the attribute is set to normal again
automatically.
reset - Re-initialises the function
normal - The function is in normal state
notApplicable - us…
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.17
ifOpticalTransLaneCarrierGroupMinimumLaneRxPowerLevel
The minimum received power level on any lane in units of 0.1 dBm.

The minimum allowed received power level per lane for 400GBASE-FR4 is -7.2 dBm
and for 400GBASE-LR4 is -9.0 dBm, specified by IEEE 802.3-c…
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.18
ifOpticalTransLaneCarrierGroupReceiverLaneSensitivity
The lowest power that the receiver is guaranteed
to handle, on a single lane, in units of 0.1 dBm.
LUM-TCSigned32WithNA
Type Constraints:
range: -2147483648..2147483647
Description:
A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently
 .1.3.6.1.4.1.8708.2.48.2.7.1.1.19