LANCOM-SWITCHING-MIB Table View

Agent Trap Log

agentTrapLogEntry row .1.3.6.1.4.1.2356.16.1.1.1.2.4.1

Agent trap log entry

Indexes

agentTrapLogIndex

Column	Syntax	OID
agentTrapLogIndex Unique index of trap entry	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.1.2.4.1.1
agentTrapLogSystemTime System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.1.2.4.1.2
agentTrapLogTrap Description of the trap sent.	OctetString Constraints: range: 0-512	.1.3.6.1.4.1.2356.16.1.1.1.2.4.1.3

Supported MIB table

agentSupportedMibEntry row .1.3.6.1.4.1.2356.16.1.1.1.3.1

Supported MIB entry

Indexes

agentSupportedMibIndex

Column	Syntax	OID
agentSupportedMibIndex Unique index of the Supported MIB entry	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.1.3.1.1
agentSupportedMibName The name of the MIB (RFC or IEEE) that is supported.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.1.3.1.2
agentSupportedMibDescription Description of the MIB (RFC or IEEE) that is supported.	OctetString Constraints: range: 0-512	.1.3.6.1.4.1.2356.16.1.1.1.3.1.3

A table of Task and cpu utilization.

agentSwitchCpuProcessEntry row .1.3.6.1.4.1.2356.16.1.1.1.4.8.1

Represents entry for a Task Table.

Indexes

agentSwitchCpuProcessIndex

Column	Syntax	OID
agentSwitchCpuProcessIndex Unique index of process table	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.1.4.8.1.1
agentSwitchCpuProcessName Name of the process	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.1.4.8.1.2
agentSwitchCpuProcessPercentageUtilization CPU utilization per task in Percentage over a period of 5, 60, 300 seconds, and the Rising threshold period also in seconds, if configured.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.1.4.8.1.3
agentSwitchCpuProcessId Process ID	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.1.4.8.1.4

Table lists the number of packets dropped at each CoS queue for the CPU.

agentSwitchCpuCosQDropEntry row .1.3.6.1.4.1.2356.16.1.1.1.6.1.1

Packet drop statistics for a CPU CoS queue.

Indexes

agentSwitchCpuCosQIndex

Column	Syntax	OID
agentSwitchCpuCosQIndex Unique index of a CPU CoS queue.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.1.6.1.1.1
agentSwitchCpuCosQDrops Number of packets dropped at this CPU CoS queue because the queue was full.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.1.6.1.1.2

Table lists information about message buffer allocation for packets arriving at the CPU.

agentSwitchMbufEntry row .1.3.6.1.4.1.2356.16.1.1.1.7.2.1

Information on a specific class of message buffers.

Indexes

agentSwitchMbufPrio

Column	Syntax	OID
agentSwitchMbufPrio Message buffer priority.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.1.7.2.1.1
agentSwitchMbufClassName Name of this class of message buffer.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.1.7.2.1.2
agentSwitchMbufAllocAttempts Number of times the system tried to allocate a message buffer allocation of this class.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.1.7.2.1.3
agentSwitchMbufAllocFails Number of message buffer allocation failures for this class of message buffer.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.1.7.2.1.4

A table that contains CPU Traffic Filter configuration.
An entry appears in this table for each supported direction (RX or TX).

agentCpuTrafficEntry row .1.3.6.1.4.1.2356.16.1.1.1.10.4.1

CPU Traffic Filter configuration including direction,
filters and custom filter's parameters.

Indexes

agentCpuTrafficDirection

Column	Syntax	OID
agentCpuTrafficDirection Unique CPU Traffic Filter direction Transmit or Receive (TX or RX).	Enumeration Enumerated Values: 1 transmit 2 receive	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.1
agentCpuTrafficFilterMask BitMask indicating which filter to configure for CPU Traffic Filter. Each filter corresponds to unique bit in the bitmask. Each byte stores 8 filter types. First filter is located in the most significant bit (MSB) of fi…	OctetStringr/w	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.2
agentCpuTrafficSourceIPType Source IP address type for CPU Traffic source IP filter. Must be set together with agentCpuTrafficSourceIP object.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.3
agentCpuTrafficSourceIP Source IP address for CPU Traffic source IP filter. Must be set together with agentCpuTrafficSourceIPType object.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.4
agentCpuTrafficSourceIPMaskType Source IP address Mask type for CPU Traffic source IP filter. Must be set together with agentCpuTrafficSourceIPMask object.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.5
agentCpuTrafficSourceIPMask Source IP address Mask for CPU Traffic source IP filter. Must be set together with agentCpuTrafficSourceIPMaskType object.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.6
agentCpuTrafficDestinationIPType Destination IP address type for CPU Traffic destination IP filter. Must be set together with agentCpuTrafficDestinationIP object.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.7
agentCpuTrafficDestinationIP Destination IP address for CPU Traffic destination IP filter. Must be set together with agentCpuTrafficDestinationIPType object.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.8
agentCpuTrafficDestinationIPMaskType Destination IP address Mask type for CPU Traffic destination IP filter. Must be set together with agentCpuTrafficDestinationIPMask object.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.9
agentCpuTrafficDestinationIPMask Destination IP address Mask for CPU Traffic destination IP filter. Must be set together with agentCpuTrafficDestinationIPMaskType object.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.10
agentCpuTrafficSourceMAC Source MAC address for CPU traffic source MAC filter. MAC address format must include 6 bytes separated using colon. For example: FF:FF:FF:FF:FF:FF.	RFC1213-MIBPhysAddressr/w	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.11
agentCpuTrafficSourceMACMask Source MAC address Mask for CPU traffic source MAC filter. MAC address format must include 6 bytes separated using colon. For example: FF:FF:FF:FF:FF:FF.	RFC1213-MIBPhysAddressr/w	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.12
agentCpuTrafficDestinationMAC Destination MAC address for CPU traffic destination MAC filter. MAC address format must include 6 bytes separated using colon. For example: FF:FF:FF:FF:FF:FF.	RFC1213-MIBPhysAddressr/w	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.13
agentCpuTrafficDestinationMACMask Destination MAC address Mask for CPU traffic destination MAC filter. MAC address format must include 6 bytes separated using colon. For example: FF:FF:FF:FF:FF:FF.	RFC1213-MIBPhysAddressr/w	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.14
agentCpuTrafficCustomFilter Custom filter parameters for CPU traffic custom filter. Filter is used to specify a set of triplets in the following format: [offset value mask]. Each option is a two byte hex number. ASCII character 'space' is used to …	OctetStringr/w	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.15
agentCpuTrafficSourceTcpPort Source TCP port value for CPU traffic filter source filter.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.16
agentCpuTrafficSourceTcpPortMask Mask value for source TCP port filter option.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.17
agentCpuTrafficDestinationTcpPort Destination TCP port value for CPU traffic filter destination filter.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.18
agentCpuTrafficDestinationTcpPortMask Mask value for destination TCP port filter option.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.19
agentCpuTrafficSourceUdpPort Source UDP port value for CPU traffic filter source filter.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.20
agentCpuTrafficSourceUdpPortMask Mask value for source UDP port filter option.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.21
agentCpuTrafficDestinationUdpPort Destination UDP port value for CPU traffic filter destination filter.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.22
agentCpuTrafficDestinationUdpPortMask Mask value for destination UDP port filter option.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.23
agentCpuTrafficInterface BitMask indicating which interface(s) to configure for CPU Traffic Filter. First interface is located in the most significant bit (MSB) of the first byte (bytes are counted from left to right). Bitmask must be specified…	LANCOM-REF-MIBAgentPortMaskr/w	.1.3.6.1.4.1.2356.16.1.1.1.10.4.1.24

A table of Power Information.

agentPowerInformationUnitEntry row .1.3.6.1.4.1.2356.16.1.1.1.40.1

An entry of Power Information table.

Indexes

agentPowerInformationUnitNumber

Column	Syntax	OID
agentPowerInformationUnitNumber The unit number associated with this unit.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.1.40.1.1
agentPowerInformationUnitPSUStatusA The status of power supply unit A.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.1.40.1.2
agentPowerInformationUnitPSUStatusB The status of power supply unit B.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.1.40.1.3
agentPowerInformationUnitFANSpeedA The fan speed of power supply unit A.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.1.40.1.4
agentPowerInformationUnitFANSpeedB The fan speed of power supply unit B.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.1.40.1.5
agentPowerInformationUnitTemperatureA The temperature of power supply unit A.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.1.40.1.6
agentPowerInformationUnitTemperatureB The temperature of power supply unit B.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.1.40.1.7
agentPowerInformationUnitOperatingMode The operating mode of power supply unit. 0:Boost 1:Redundant	Integer32r/w Constraints: range: 0-1	.1.3.6.1.4.1.2356.16.1.1.1.40.1.8

A table of the switch's login session

agentLoginSessionEntry row .1.3.6.1.4.1.2356.16.1.1.2.1.1.1

Login Session Entry

Indexes

agentLoginSessionIndex

Column	Syntax	OID
agentLoginSessionIndex Agent Login Session Index of the switch	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.1.1.1.1
agentLoginSessionUserName Agent Login Session UserName of the switch	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.2.1.1.1.2
agentLoginSessionIPAddressobsolete Agent Login Session IP Address of the switch	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.2356.16.1.1.2.1.1.1.3
agentLoginSessionConnectionType Agent Login Session Connection Type of the switch	Enumeration Enumerated Values: 1 serial 2 telnet 3 ssh 4 http 5 https	.1.3.6.1.4.1.2356.16.1.1.2.1.1.1.4
agentLoginSessionIdleTime Agent Login Session Idle Time of the switch	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.1.1.1.5
agentLoginSessionSessionTime Agent Login Session Time of the switch	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.1.1.1.6
agentLoginSessionStatus Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.1.1.1.7
agentLoginSessionInetAddressType Type of address agentLoginSessionInetAddress is returning. Can be either unknown(0), ipv4(1), or ipv6 (2). Will return unknown(0) in the case of a serial login.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.2356.16.1.1.2.1.1.1.8
agentLoginSessionInetAddress Inet Address of the connecting the user is logging in with. Will return a zero-length string in the case of a serial login.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.2356.16.1.1.2.1.1.1.9

User Config Table

agentUserConfigEntry row .1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1

User Config Entry

Indexes

agentUserIndex

Column	Syntax	OID
agentUserIndex Agent User Config Index	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.1
agentUserName Agent User Name. This string is limited to alpha-numeric strings (including the '-' and '_' characters).	OctetStringr/w Constraints: range: 1-64	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.2
agentUserPassword Agent User Password This object will return an empty string even if a password is set.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.3
agentUserAccessModeobsolete Agent User Access Mode. This object is deprecated in favor of agentUserAccessLevel.	Enumerationr/w Enumerated Values: 1 read 2 write 3 suspended	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.4
agentUserStatus Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.5
agentUserLockoutStatus Displays whether the user account is locked due to excessive failed login attempts.	Enumeration Enumerated Values: 0 false 1 true	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.9
agentUserPasswordExpireTime Date and time when the user's password expires (past or present). Only valid when password aging is enabled.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.10
agentUserAccessLevel Agent User Access Level. Supported values are 0, 1 and 15.	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.11
agentUserGroups This variable is used for selecting/unselecting configured user groups. First user group has index 1, and bitmask value 8000. Last user group has index 10, and bit mask value 0040.	OctetStringr/w	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.12
agentUserSshPublicKey The user ssh Public key file is used for ssh secure login for user without password.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.13
agentUserPasswordEncryptType User password encryption algorithm Type. md5(5) - MD5 aes(6) - AES - 128	Enumerationr/w Enumerated Values: 5 md5 6 aes	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.14
agentUserPasswordEncrypted Specifies whether the password is encrypted or not.	Enumerationr/w Enumerated Values: 0 false 1 true	.1.3.6.1.4.1.2356.16.1.1.2.1.3.2.1.15

Represents Password strength restricted keywords from the configurable password.

agentPasswordManagementStrengthExcludeKeywordEntry row .1.3.6.1.4.1.2356.16.1.1.2.1.6.15.1

Represents Password strength restricted keywords from the configurable password.

Indexes

agentPasswordMgmtStrengthExcludeKeyword

Column	Syntax	OID
agentPasswordMgmtStrengthExcludeKeyword Specifies the given keyword string restricted from the configurable password.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.2.1.6.15.1.1
agentPasswordMgmtStrengthExcludeKeywordStatus Create the Exclude Keyword Index and configure (Create or Destroy) the keyword to it.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.1.6.15.1.2

A table for dot1x Client details and associated functionality.

agentIASUserConfigEntry row .1.3.6.1.4.1.2356.16.1.1.2.1.7.2.1

Represents entry for port config table.

Indexes

agentIASUserIndex

Column	Syntax	OID
agentIASUserIndex IAS user config index.	Integer32 Constraints: range: 0-99	.1.3.6.1.4.1.2356.16.1.1.2.1.7.2.1.1
agentIASUserName IAS user name. This string is limited to alpha-numeric strings (including '-' and '_' characters).	OctetStringr/w Constraints: range: 1-64	.1.3.6.1.4.1.2356.16.1.1.2.1.7.2.1.2
agentIASUserPassword IAS user password.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.2356.16.1.1.2.1.7.2.1.3
agentIASUserStatus IAS User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.1.7.2.1.4

Task group configuration table.

agentUserMgrTaskGroupEntry row .1.3.6.1.4.1.2356.16.1.1.2.1.9.1.1

Task group configuration entry.

Indexes

agentUserMgrTaskGroupIndex

Column	Syntax	OID
agentUserMgrTaskGroupIndex Index of selected task group.	Unsigned32 Constraints: range: 0-9	.1.3.6.1.4.1.2356.16.1.1.2.1.9.1.1.1
agentUserMgrTaskGroupName Name of selected task group.	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.2356.16.1.1.2.1.9.1.1.2
agentUserMgrTaskGroupDescription Textual description of selected task group (optional).	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.2356.16.1.1.2.1.9.1.1.3
agentUserMgrTaskGroupInherit Bit mask variable for configuring inherited task groups. First task group has index 1 and bitmask value is 8000. Last task group has index 9 and bitmask value is 0080.	OctetStringr/w	.1.3.6.1.4.1.2356.16.1.1.2.1.9.1.1.4
agentUserMgrTaskGroupRowStatus Row status value of user group table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.1.9.1.1.5

Task permission configuration table.

agentUserMgrTaskGroupPermissionsEntry row .1.3.6.1.4.1.2356.16.1.1.2.1.9.2.1.1

Task permission configuration entry.

Indexes

agentUserMgrTaskGroupIndex agentUserMgrTaskGroupTaskIndex

Column	Syntax	OID
agentUserMgrTaskGroupTaskIndex Index of selected task.	Enumeration Enumerated Values: 0 aaa 1 bgp 2 ospf	.1.3.6.1.4.1.2356.16.1.1.2.1.9.2.1.1.1
agentUserMgrTaskGroupTaskPermission Value of permission for selected task. Tasks may have multiple permissions.	Bitsr/w Enumerated Values: 0 read 1 write 2 execute 3 debug	.1.3.6.1.4.1.2356.16.1.1.2.1.9.2.1.1.2
agentUserMgrTaskGroupTaskOperationalPermission Value of operational permissions for selected task. Consists of configured permissions for selected task and inherited permissions.	Bits Enumerated Values: 0 read 1 write 2 execute 3 debug	.1.3.6.1.4.1.2356.16.1.1.2.1.9.2.1.1.3

User group configuration table.

agentUserMgrUserGroupEntry row .1.3.6.1.4.1.2356.16.1.1.2.1.10.1.1

User group configuration entry.

Indexes

agentUserMgrUserGroupIndex

Column	Syntax	OID
agentUserMgrUserGroupIndex Index of selected user group.	Unsigned32 Constraints: range: 0-9	.1.3.6.1.4.1.2356.16.1.1.2.1.10.1.1.1
agentUserMgrUserGroupName Name of selected user group.	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.2356.16.1.1.2.1.10.1.1.2
agentUserMgrUserGroupDescription Textual description of selected user group (optional).	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.2356.16.1.1.2.1.10.1.1.3
agentUserMgrUserGroupInherit Bit mask variable for configuring inherited user groups. First user group has index 1 and bitmask value is 8000. Last user group has index 9 and bitmask value is 0080.	OctetStringr/w	.1.3.6.1.4.1.2356.16.1.1.2.1.10.1.1.4
agentUserMgrUserGroupContainedTaskGroups Bit mask variable for configuring contained task groups. First task group has index 1 and bitmask value is 8000. Last task group has index 10 and bitmask value is 0040.	OctetStringr/w	.1.3.6.1.4.1.2356.16.1.1.2.1.10.1.1.5
agentUserMgrUserGroupRowStatus Row status value of user group table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.1.10.1.1.6

A summary table of the switch's LAG config entries

agentLagSummaryConfigEntry row .1.3.6.1.4.1.2356.16.1.1.2.2.2.1

Switch's LAG config entry

Indexes

agentLagSummaryLagIndex

Column	Syntax	OID
agentLagSummaryLagIndex Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.1
agentLagSummaryName Agent LAG Name. The associated name of the LAG used during creation. Duplicate names are not allowed.	OctetStringr/w Constraints: range: 1-15	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.2
agentLagSummaryFlushTimerobsolete Agent LAG FlushTimer.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.3
agentLagSummaryLinkTrap Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.4
agentLagSummaryAdminMode Agent LAG AdminMode. Administratively enables or disables this LAG interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.5
agentLagSummaryStpMode Agent LAG StpMode Administratively enables or disables STP on this interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.6
agentLagSummaryAddPort Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: agentPortType for the port to be added must be full duplex and t…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.7
agentLagSummaryDeletePort Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.8
agentLagSummaryStatus Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.9
agentLagSummaryType Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained.	Enumeration Enumerated Values: 1 static 2 dynamic	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.10
agentLagSummaryStaticCapability Agent LAG Static Capability enable(1) - Static capability is enabled for this LAG interface disable(2) - Static capability is disabled for this LAG interface	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.11
agentLagSummaryHashOption LAG Hashing Option. Valid values correspond to 1 (=Source MAC, VLAN, EtherType, and incoming port associated with the packet) 2 (=Destination MAC, VLAN, EtherType, and incoming port …	Integer32r/w Constraints: range: 1-7	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.12
agentLagSummaryMinimumActiveLinks Agent LAG Threshold. This configures the threshold(i.e minimum number of active ports) value for trunk port .	Integer32r/w Constraints: range: 1-8	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.13
agentLagSummaryLocalPreferenceMode Agent LAG Local Preference Mode. Enables or disables the LAG interface's Local Preference Mode.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.14
agentLagSummaryMtuValue Configures the MTU value for this LAG interface. The maximum value is dependent on the platform.	Unsigned32r/w Constraints: range: 1518-12288	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.15
agentLagSummaryPortCounter LAG port flap counter.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.17
agentLagSummaryRateLoadInterval The length of time for which data is used to compute load statistics. The value is given in seconds, and must be a multiple of 30. The allowable range is 30 to 600 seconds.	Integer32r/w Constraints: range: 30-600	.1.3.6.1.4.1.2356.16.1.1.2.2.2.1.18

A detailed table of the switch's LAG config entries

agentLagDetailedConfigEntry row .1.3.6.1.4.1.2356.16.1.1.2.2.3.1

Switch's LAG config entry

Indexes

agentLagDetailedLagIndex agentLagDetailedIfIndex

Column	Syntax	OID
agentLagDetailedLagIndex LAG index	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.2.3.1.1
agentLagDetailedIfIndex LAG port index	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.2.3.1.2
agentLagDetailedPortSpeed LAG port speed. See agentPortType for a description and list of valid values.	ObjectIdentifier	.1.3.6.1.4.1.2356.16.1.1.2.2.3.1.3
agentLagDetailedPortStatus LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG.	Enumeration Enumerated Values: 1 active 2 inactive	.1.3.6.1.4.1.2356.16.1.1.2.2.3.1.4
agentLagDetailedPortCounter LAG port flap counter.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.2.3.1.5

The list of IPv6 address prefixes
for the network port.

agentNetworkIpv6AddrEntry row .1.3.6.1.4.1.2356.16.1.1.2.3.14.1

An interface entry containing objects of
a particular IPv6 address prefix

Indexes

agentNetworkIpv6AddrPrefix

Column	Syntax	OID
agentNetworkIpv6AddrPrefix The service port IPv6 Address Prefix	Ipv6AddressPrefix Type Constraints: range: 0..16	.1.3.6.1.4.1.2356.16.1.1.2.3.14.1.1
agentNetworkIpv6AddrPrefixLength The service port IPv6 Address Prefix Length	Integer32r/w Constraints: range: 0-128	.1.3.6.1.4.1.2356.16.1.1.2.3.14.1.2
agentNetworkIpv6AddrEuiFlag The service port IPv6 Eui Flag	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.2356.16.1.1.2.3.14.1.3
agentNetworkIpv6AddrStatus	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.3.14.1.4

The list of IPv6 address prefixes for the
service port.

agentServicePortIpv6AddrEntry row .1.3.6.1.4.1.2356.16.1.1.2.4.9.1

An interface entry containing objects of
a particular IPv6 address prefix

Indexes

agentServicePortIpv6AddrPrefix

Column	Syntax	OID
agentServicePortIpv6AddrPrefix The service port IPv6 Address Prefix	Ipv6AddressPrefix Type Constraints: range: 0..16	.1.3.6.1.4.1.2356.16.1.1.2.4.9.1.1
agentServicePortIpv6AddrPrefixLength The service port IPv6 Address Prefix Length	Integer32r/w Constraints: range: 0-128	.1.3.6.1.4.1.2356.16.1.1.2.4.9.1.2
agentServicePortIpv6AddrEuiFlag The service port IPv6 Eui Flag	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.2356.16.1.1.2.4.9.1.3
agentServicePortIpv6AddrStatus	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.4.9.1.4

The switch's static Mac filtering table

agentSwitchStaticMacFilteringEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.5.1

Per-port ingress/egress filter configuration based on VLAN Id and MAC address.

Indexes

agentSwitchStaticMacFilteringVlanId agentSwitchStaticMacFilteringAddress

Column	Syntax	OID
agentSwitchStaticMacFilteringVlanId The Static MAC Filter Vlan Id	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.8.5.1.1
agentSwitchStaticMacFilteringAddress The Static MAC Filter MAC address	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2356.16.1.1.2.8.5.1.2
agentSwitchStaticMacFilteringSourcePortMask The Static MAC Filter source port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this …	LANCOM-REF-MIBAgentPortMaskr/w	.1.3.6.1.4.1.2356.16.1.1.2.8.5.1.3
agentSwitchStaticMacFilteringDestPortMask The Static MAC Filter destination port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between …	LANCOM-REF-MIBAgentPortMaskr/w	.1.3.6.1.4.1.2356.16.1.1.2.8.5.1.4
agentSwitchStaticMacFilteringStatus The Static MAC Filter status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.8.5.1.5

A table of the IGMP/MLD Snooping Global configuration entries.

agentSwitchSnoopingCfgEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.6.1.1

Represents entry for Snooping switch Configuration.

Indexes

agentSwitchSnoopingProtocol

Column	Syntax	OID
agentSwitchSnoopingProtocol The protocol type of network protocol in use.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.2356.16.1.1.2.8.6.1.1.1
agentSwitchSnoopingAdminMode This enables or disables Snooping on the system.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.8.6.1.1.2
agentSwitchSnoopingPortMask IGMP/MLD Snooping Port Mask. This allows configuration of IGMP/MLD Snooping on selected ports. IGMP/MLD Snooping cannot be enabled on an interface that has routing enabled, or is a member of a LAG. If a …	LANCOM-REF-MIBAgentPortMaskr/w	.1.3.6.1.4.1.2356.16.1.1.2.8.6.1.1.3
agentSwitchSnoopingMulticastControlFramesProcessed Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.6.1.1.4

A table of the IGMP/MLD Snooping Interface configuration entries.

agentSwitchSnoopingIntfEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.7.1.1

Represents entry for a IGMP/MLD Snooping Interface.

Indexes

IF-MIBifIndex agentSwitchSnoopingProtocol

Column	Syntax	OID
agentSwitchSnoopingIntfIndex The port number to be selected. Each port maps to an interface.	Unsigned32 Constraints: range: 1-65535	.1.3.6.1.4.1.2356.16.1.1.2.8.7.1.1.1
agentSwitchSnoopingIntfAdminMode This enables or disables IGMP/MLD Snooping on a selected interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.8.7.1.1.2
agentSwitchSnoopingIntfGroupMembershipInterval The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the entry. This value must be greater than agentSwitchSnoopingIntfM…	Integer32r/w Constraints: range: 2-3600	.1.3.6.1.4.1.2356.16.1.1.2.8.7.1.1.3
agentSwitchSnoopingIntfMaxResponseTime The amount of time in seconds a switch will wait after sending a query on the selected interface because it did not receive a report for a particular group in that interface. This value must be less than agentSwitchSno…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.2.8.7.1.1.4
agentSwitchSnoopingIntfMRPExpirationTime The amount of time in seconds that a switch will wait for a query to be received on the selected interface before the interface is removed from the list of interfaces with multicast routers attached.	Integer32r/w Constraints: range: 0-3600	.1.3.6.1.4.1.2356.16.1.1.2.8.7.1.1.5
agentSwitchSnoopingIntfFastLeaveAdminMode This enables or disables IGMP/MLD Snooping on the selected interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.8.7.1.1.6
agentSwitchSnoopingIntfMulticastRouterMode This enables or disables Multicast Routing on the selected interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.8.7.1.1.7
agentSwitchSnoopingIntfVlanIDs This field lists all the VlanIDs which include the selected interface.	VlanList	.1.3.6.1.4.1.2356.16.1.1.2.8.7.1.1.8

A table of the IGMP/MLD Snooping Vlan configuration entries.

agentSwitchSnoopingVlanEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.8.1.1

Represents entry for a IGMP/MLD Snooping Vlan.

Indexes

Q-BRIDGE-MIBdot1qVlanIndex agentSwitchSnoopingProtocol

Column	Syntax	OID
agentSwitchSnoopingVlanAdminMode This enables or disables IGMP/MLD Snooping on a selected Vlan interface.	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.2356.16.1.1.2.8.8.1.1.1
agentSwitchSnoopingVlanGroupMembershipInterval The amount of time in seconds that a switch will wait for a report from a particular group on the selected vlan before deleting the interface participating in the vlan from the entry. This value must be greater than age…	Integer32r/w Constraints: range: 2-3600	.1.3.6.1.4.1.2356.16.1.1.2.8.8.1.1.2
agentSwitchSnoopingVlanMaxResponseTime The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This value must be less …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.2.8.8.1.1.3
agentSwitchSnoopingVlanFastLeaveAdminMode This enables or disables IGMP/MLD Snooping on the selected vlan.	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.2356.16.1.1.2.8.8.1.1.4
agentSwitchSnoopingVlanMRPExpirationTime The amount of time in seconds that a switch will wait for a query to be received on the selected interface participating in the vlan before the interface is removed from the list of interfaces with multicast routers att…	Integer32r/w Constraints: range: 0-3600	.1.3.6.1.4.1.2356.16.1.1.2.8.8.1.1.5
agentSwitchSnoopingVlanReportSuppMode This enables or disables IGMP Snooping Report Suppression feature on the selected vlan.	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.2356.16.1.1.2.8.8.1.1.6

A table of the IGMP/MLD Static Mrouter Configuration parameters.

agentSwitchVlanStaticMrouterEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.9.1.1

Represents entry for a IGMP/MLD Static Mrouter.

Indexes

IF-MIBifIndex Q-BRIDGE-MIBdot1qVlanIndex agentSwitchSnoopingProtocol

Column	Syntax	OID
agentSwitchVlanStaticMrouterAdminMode This enables or disables IGMP/MLD Mrouter on a per-interface per-vlan basis.	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.2356.16.1.1.2.8.9.1.1.1

The Multicast Forwarding Database table

agentSwitchMFDBEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.10.1.1

Contains Forwarding and Filtering information per Vlan Index, MAC Address, and
Component User.

Indexes

agentSwitchMFDBVlanId agentSwitchMFDBMacAddress agentSwitchMFDBProtocolType

Column	Syntax	OID
agentSwitchMFDBVlanId Vlan Index for which this entry is associated with.	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.2356.16.1.1.2.8.10.1.1.1
agentSwitchMFDBMacAddress A multicast MAC address for which the switch has forwarding and or filtering information.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2356.16.1.1.2.8.10.1.1.2
agentSwitchMFDBProtocolType The component that is responsible for this entry in the Multicast Forwarding Database.	Enumeration Enumerated Values: 1 static 2 gmrp 3 igmp 4 mld	.1.3.6.1.4.1.2356.16.1.1.2.8.10.1.1.3
agentSwitchMFDBType This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol	Enumeration Enumerated Values: 1 static 2 dynamic	.1.3.6.1.4.1.2356.16.1.1.2.8.10.1.1.4
agentSwitchMFDBDescription Text description of this multicast table entry.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2356.16.1.1.2.8.10.1.1.5
agentSwitchMFDBForwardingPortMask BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTa…	LANCOM-REF-MIBAgentPortMask	.1.3.6.1.4.1.2356.16.1.1.2.8.10.1.1.6
agentSwitchMFDBFilteringPortMask BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTab…	LANCOM-REF-MIBAgentPortMask	.1.3.6.1.4.1.2356.16.1.1.2.8.10.1.1.7

The Multicast Forwarding Database Summary table

agentSwitchMFDBSummaryEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.10.2.1

Summarizes the forwarding ports for all components registered for all
MFDB table entries with the same Vlan Index and MAC Address.

Indexes

agentSwitchMFDBSummaryVlanId agentSwitchMFDBSummaryMacAddress

Column	Syntax	OID
agentSwitchMFDBSummaryVlanId Vlan Index for which this entry is associated with.	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.2356.16.1.1.2.8.10.2.1.1
agentSwitchMFDBSummaryMacAddress A multicast MAC address for which the switch has forwarding and or filtering information.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2356.16.1.1.2.8.10.2.1.2
agentSwitchMFDBSummaryForwardingPortMask Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfig…	LANCOM-REF-MIBAgentPortMask	.1.3.6.1.4.1.2356.16.1.1.2.8.10.2.1.3

A table of entries specifying the ethertype (TPID) values.
This will let the user specify multiple ethertypes globally.

agentSwitchDVlanTagEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.11.2.1

A table entry specifying the ethertype (TPID) values.
Commonly used are the Ethertypes for vman tags (34984, or 0x88A8)
and dot1q tags (33024, or 0x8100).

Indexes

agentSwitchDVlanTagTPid

Column	Syntax	OID
agentSwitchDVlanTagTPid Ethertype value to identify incoming double tagged frames	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.2356.16.1.1.2.8.11.2.1.1
agentSwitchDVlanTagPrimaryTPid Specifies if this TPID is primary TPID for the switch or not. As the system needs one TPID to be active all the time, setting the object to false doesn't modify/remove the entry. Adding another entry and setting it to t…	Enumerationr/w Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.2356.16.1.1.2.8.11.2.1.2
agentSwitchDVlanTagRowStatus Row status	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.8.11.2.1.3

A table entries specifying the ethertype (TPID) values per port.

agentSwitchPortDVlanTagEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.11.3.1

A table entry specifying the ethertype (TPID) value for a port.

Indexes

agentSwitchPortDVlanTagInterfaceIfIndex agentSwitchPortDVlanTagTPid

Column	Syntax	OID
agentSwitchPortDVlanTagInterfaceIfIndex Port Id on to which the Ethertype value is mapped	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.8.11.3.1.1
agentSwitchPortDVlanTagTPid Ethertype value to identify incoming double tagged frames	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.2356.16.1.1.2.8.11.3.1.2
agentSwitchPortDVlanTagMode Controls the Double Vlan Tag mode on this port.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.8.11.3.1.3
agentSwitchPortDVlanTagCustomerId Configures the Customer ID for the Double Vlan Tag for this port.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.2.8.11.3.1.4
agentSwitchPortDVlanTagRowStatus Row status	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.8.11.3.1.5

The switch's MAC To VLAN association table

agentSwitchVlanMacAssociationEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.17.1.1

VLAN to be assigned to untagged or priority tagged
packets based on MAC address.

Indexes

agentSwitchVlanMacAssociationMacAddress agentSwitchVlanMacAssociationVlanId

Column	Syntax	OID
agentSwitchVlanMacAssociationMacAddress The Mac address	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2356.16.1.1.2.8.17.1.1.1
agentSwitchVlanMacAssociationVlanId The VLAN the Mac address assigned to	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.2356.16.1.1.2.8.17.1.1.2
agentSwitchVlanMacAssociationRowStatus The Mac to VLAN association row status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.8.17.1.1.3

The switch's protected port mapping table

agentSwitchProtectedPortEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.18.1.1

Protected ports assigned to groups.

Indexes

agentSwitchProtectedPortGroupId

Column	Syntax	OID
agentSwitchProtectedPortGroupId The group that this port belongs to	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.8.18.1.1.1
agentSwitchProtectedPortGroupName The name of the group	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2356.16.1.1.2.8.18.1.1.2
agentSwitchProtectedPortPortList The set of ports that are protected in this group	PortListr/w	.1.3.6.1.4.1.2356.16.1.1.2.8.18.1.1.3

The switch's Subnet To VLAN association table

agentSwitchVlanSubnetAssociationEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.19.1.1

VLAN to be assigned to untagged or priority tagged
packets based on IP address and Subnet Mask.

Indexes

agentSwitchVlanSubnetAssociationIPAddress agentSwitchVlanSubnetAssociationSubnetMask agentSwitchVlanSubnetAssociationVlanId

Column	Syntax	OID
agentSwitchVlanSubnetAssociationIPAddress The ip address	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.2356.16.1.1.2.8.19.1.1.1
agentSwitchVlanSubnetAssociationSubnetMask The subnet mask	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.2356.16.1.1.2.8.19.1.1.2
agentSwitchVlanSubnetAssociationVlanId The VLAN that the IP address and subnet mask assigned to	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.2356.16.1.1.2.8.19.1.1.3
agentSwitchVlanSubnetAssociationRowStatus The Subnet to VLAN association row status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.8.19.1.1.4

A table of the IGMP/MLD Snooping Querier Global configuration entries.

agentSwitchSnoopingQuerierCfgEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.20.1.1

Represents entry for Snooping Querier Configuration.

Indexes

agentSwitchSnoopingProtocol

Column	Syntax	OID
agentSwitchSnoopingQuerierAdminMode This enables or disables Snooping Querier on the system.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2356.16.1.1.2.8.20.1.1.1
agentSwitchSnoopingQuerierVersion This specifies the multicast protocol versions that are supported by the system.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.2.8.20.1.1.2
agentSwitchSnoopingQuerierAddress This specifies the default source ip address to be used while generating general queries.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2356.16.1.1.2.8.20.1.1.3
agentSwitchSnoopingQuerierQueryInterval This specified the timer interval after which the system generates general queries.	Integer32r/w Constraints: range: 1-1800	.1.3.6.1.4.1.2356.16.1.1.2.8.20.1.1.4
agentSwitchSnoopingQuerierExpiryInterval This specified the timer interval after which the detected other querier information is no longer valid.	Integer32r/w Constraints: range: 60-300	.1.3.6.1.4.1.2356.16.1.1.2.8.20.1.1.5

A table of the Snooping Querier Vlan configuration entries.

agentSwitchSnoopingQuerierVlanEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.20.2.1

Represents entry for a Snooping Querier configurable Vlan.

Indexes

Q-BRIDGE-MIBdot1qVlanIndex agentSwitchSnoopingProtocol

Column	Syntax	OID
agentSwitchSnoopingQuerierVlanAdminMode This enables or disables Snooping Querier on a selected Vlan interface.	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.2356.16.1.1.2.8.20.2.1.1
agentSwitchSnoopingQuerierVlanOperMode This specifies the current state of the Snooping Querier on a selected vlan interface	Enumeration Enumerated Values: 0 disabled 1 querier 2 non-querier	.1.3.6.1.4.1.2356.16.1.1.2.8.20.2.1.2
agentSwitchSnoopingQuerierElectionParticipateMode This enables or disables the Snooping Querier Election Participation mode. When enabled snooping querier switch will participate in querier election up on discovering another querier in the specified vlan. When disabled…	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.2356.16.1.1.2.8.20.2.1.3
agentSwitchSnoopingQuerierVlanAddress This specifies the default source ip address to be used while generating general queries on the specified vlan.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2356.16.1.1.2.8.20.2.1.4
agentSwitchSnoopingQuerierOperVersion This specifies the multicast protocol version that is currently being used by the snooping switch for the specified vlan while generating query messages.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.2.8.20.2.1.5
agentSwitchSnoopingQuerierOperMaxResponseTime The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This object is valid onl…	Integer32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.2356.16.1.1.2.8.20.2.1.6
agentSwitchSnoopingQuerierLastQuerierAddress This specifies the last querier's ip address for the specified vlan. It represents the detected other multicast querier in the vlan.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.2356.16.1.1.2.8.20.2.1.7
agentSwitchSnoopingQuerierLastQuerierVersion This specifies the multicast protocol version that is currently being used by the detected other multicast querier for the specified vlan. (-1) - indicates that parameter is not available.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2356.16.1.1.2.8.20.2.1.8

A table provides the mechanism to control Dynamic ARP
Inspection per VLAN. When a VLAN is created in a device
supporting this table, a corresponding entry of this table
will be added.

agentDaiVlanConfigEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.21.4.1

A row instance contains the configuration for Dynamic
ARP Inspection at each existing VLAN.

Indexes

agentDaiVlanIndex

Column	Syntax	OID
agentDaiVlanIndex This object indicates the VLAN number on which Dynamic ARP Inspection feature is configured.	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.2356.16.1.1.2.8.21.4.1.1
agentDaiVlanDynArpInspEnable This object indicates whether Dynamic ARP Inspection is enabled in this VLAN. If this object is set to 'true', Dynamic ARP Inspection is enabled. If this object is set to 'false', Dynamic A…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2356.16.1.1.2.8.21.4.1.2
agentDaiVlanLoggingEnable This object indicates whether the Dynamic ARP Inspection logging is enabled on this VlAN. If this object is set to 'true', Dynamic ARP Inspection logging is enabled. If this object is set to 'false', Dynamic ARP Inspect…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2356.16.1.1.2.8.21.4.1.3
agentDaiVlanArpAclName This object indicates the ARP ACL name set for this VLAN.	OctetStringr/w Constraints: range: 0-31	.1.3.6.1.4.1.2356.16.1.1.2.8.21.4.1.4
agentDaiVlanArpAclStaticFlag This object indicates whether the ARP ACL set for this VLAN has static flag set. If this object is set to 'true', static flag is enabled. If this object is set to 'false', static flag is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2356.16.1.1.2.8.21.4.1.5

A table provides the mechanism to control Dynamic ARP
Inspection per VLAN. When a VLAN is created in a device
supporting this table, a corresponding entry of this table
will be added.

agentDaiVlanStatsEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1

A row instance contains the Dynamic ARP Inspection
statistics per VLAN.

Indexes

agentDaiVlanStatsIndex

Column	Syntax	OID
agentDaiVlanStatsIndex This object indicates the VLAN number on which Dynamic ARP Inspection statistics are retrieved.	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.1
agentDaiVlanPktsForwarded Number of valid ARP packets forwarded by DAI.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.2
agentDaiVlanPktsDropped Number of invalid ARP packets dropped by DAI.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.3
agentDaiVlanDhcpDrops Number of ARP packets that were dropped by DAI as there is no matching DHCP Snooping binding entry found.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.4
agentDaiVlanDhcpPermits Number of ARP packets that were forwarded by DAI as there is a matching DHCP Snooping binding entry found.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.5
agentDaiVlanAclDrops Number of ARP packets that were dropped by DAI as there is no matching ARP ACL rule found for this Vlan and the static flag is set on this vlan.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.6
agentDaiVlanAclPermits Number of ARP packets that were permitted by DAI as there is a matching ARP ACL permit rule found for this Vlan.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.7
agentDaiVlanSrcMacFailures Number of ARP packets that were dropped by DAI as the sender mac address in ARP packet didn't match the source mac in ethernet header.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.8
agentDaiVlanDstMacFailures Number of ARP packets that were dropped by DAI as the target mac address in ARP reply packet didn't match the destination mac in ethernet header.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.9
agentDaiVlanIpValidFailures Number of ARP packets that were dropped by DAI as the sender IP address in ARP packet or target IP address in ARP reply packet is invalid. Invalid addresses include 0.0.0.0, 255.255.255.255, IP multicast addresses, clas…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.10
agentDaiVlanAclDenials Number of ARP packets that were dropped by DAI as there is a matching ARP ACL deny rule found for this Vlan.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2356.16.1.1.2.8.21.6.1.11

A table provides the mechanism to configure the trust
state for Dynamic ARP Inspection purpose at each physical
interface capable of this feature.

agentDaiIfConfigEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.21.7.1

A row instance contains the configuration for
Dynamic ARP Inspection at each physical
interface capable of this feature.

Indexes

IF-MIBifIndex

Column	Syntax	OID
agentDaiIfTrustEnable This object indicates whether the interface is trusted for Dynamic ARP Inspection purpose. If this object is set to 'true', the interface is trusted. ARP packets coming to this interface will be forwarded…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2356.16.1.1.2.8.21.7.1.1
agentDaiIfRateLimit This object indicates rate limit value for Dynamic ARP Inspection purpose. If the incoming rate of ARP packets exceeds the value of this object for consecutively burst interval seconds, ARP packets will be dropped. Valu…	packets per secondInteger32r/w Constraints: range: -1-300	.1.3.6.1.4.1.2356.16.1.1.2.8.21.7.1.2
agentDaiIfBurstInterval This object indicates the burst interval value for rate limiting purpose on this interface.	Unsigned32r/w Constraints: range: 1-15	.1.3.6.1.4.1.2356.16.1.1.2.8.21.7.1.3

A table of the ARP ACL entries

agentArpAclEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.22.1.1

Represents entry for an ARP ACL

Indexes

agentArpAclName

Column	Syntax	OID
agentArpAclName Name of the ARP ACL, which must consist of 1 to 31 alphanumeric characters and uniquely identify this ARP ACL. This object must be set to complete a new ARP ACL row instance.	OctetStringr/w Constraints: range: 1-31	.1.3.6.1.4.1.2356.16.1.1.2.8.22.1.1.1
agentArpAclRowStatus The status of this conceptual row. Entries can not be deleted until all rows in agentArpAclRuleConfigTable with corresponding values of agentArpAclName have been deleted. active(1) - …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.8.22.1.1.2

A table of the ARP ACL Rule entries.
          
The functionality that was offered by this table is now
available through the agentArpAclRuleConfigTable, although
with different table indices. All SNMP client implementations
operating on this table MUST migrate to use the new table.

agentArpAclRuleEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.22.2.1

Represents entry for a set of ARP ACL-match rules

Indexes

agentArpAclName agentArpAclRuleMatchSenderIpAddr agentArpAclRuleMatchSenderMacAddr

Column	Syntax	OID
agentArpAclRuleMatchSenderIpAddrobsolete Sender IP address match value for the ARP ACL.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.2356.16.1.1.2.8.22.2.1.1
agentArpAclRuleMatchSenderMacAddrobsolete Sender MAC address match value for the ARP ACL.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2356.16.1.1.2.8.22.2.1.2
agentArpAclRuleRowStatusobsolete The status of this conceptual row. active(1) - this ACL Rule is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.8.22.2.1.3

A table for configuration of ARP ACL remarks entries.
Created remarks will be associated with ARP ACL rule when
the rule is created.

agentArpAclRemarkConfigEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.22.3.1

The row in ARP ACL remarks configuration table.

Indexes

agentArpAclName agentArpAclRemarkIndex

Column	Syntax	OID
agentArpAclRemarkIndex Index of remark(not associated with a rule) instance within ARP ACL.	Unsigned32r/w Constraints: range: 1-10	.1.3.6.1.4.1.2356.16.1.1.2.8.22.3.1.1
agentArpAclRemarkStr ARP ACL remark(comment) string configuration. Each remark line is limited to 100 characters. Remark may consist of characters in the range A-Z, a-z, 0-9 and special characters like space, hyphen, underscore.	OctetStringr/w Constraints: range: 1-100	.1.3.6.1.4.1.2356.16.1.1.2.8.22.3.1.2
agentArpAclRemarkStatus Status of this instance. active(1) - this remark is configured. createAndGo(4) - set to this value to create the remark entry. agentArpAclRemarkStr should be specified. destroy(6) …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.8.22.3.1.3

This table displays remarks which are associated with ARP ACL rules.
Each rule can be uniquely identified with ARP ACL name, IP and MAC addresses.
Each remark within each rule can be uniquely identified with remark index.
Remarks associated with the rule can't be edited in any way.
They can be deleted only.
          
The functionality that was offered by this table is now
available through the agentArpAclRemarkRuleConfigTable,
although with different table indices. All SNMP client
implementations operating on this table MUST migrate to
use the new table.

agentArpAclRemarkRuleEntry row .1.3.6.1.4.1.2356.16.1.1.2.8.22.4.1

Row of the ARP ACL rule remarks table.

Indexes

agentArpAclName agentArpAclRuleMatchSenderIpAddr agentArpAclRuleMatchSenderMacAddr agentArpAclRuleRemarkIndex

Column	Syntax	OID
agentArpAclRuleRemarkIndexobsolete The index of the remark instance within ARP ACL rule.	Unsigned32 Constraints: range: 1-10	.1.3.6.1.4.1.2356.16.1.1.2.8.22.4.1.1
agentArpAclRuleRemarkStrobsolete Displays the remark string for the specified ARP ACL rule.	OctetString Constraints: range: 1-100	.1.3.6.1.4.1.2356.16.1.1.2.8.22.4.1.2
agentArpAclRuleRemarkStatusobsolete Status of this instance. active(1) - this remark is configured. destroy(6) - set to this value to delete the remark entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2356.16.1.1.2.8.22.4.1.3