LAN-EMULATION-CLIENT-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
10
Rows
10
Columns
79

lecConfigTable

table
.1.3.6.1.4.1.353.5.3.1.1.1 · 1 row entry · 23 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk lecConfigTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LAN-EMULATION-CLIENT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LAN-EMULATION-CLIENT-MIB::lecConfigTable' 
A table describing all of the LAN Emulation Clients
implemented by this host.  Each LE Client has a row
in the MIB-II/RFC 1573 Interfaces table (describing
the emulated packet interface it presents to higher
layers).  Each LE Client also has a row in this and
other LEC MIB tables (describing its interface with
other LAN Emulation components).
          
This table contains configuration variables.  Three
extension tables contain client status, performance
statistics, and information about control/multicast
VCCs.
          
Unlike hardware ports, LE Clients can be created by
management.  However, the RFC 1573 Interfaces table
does not directly support row creation.  Therefore,
creating or deleting a row in the lecConfigTable is
defined to have the side effect of creating or
deleting corresponding rows in
          
    -  the MIB-II / RFC 1573 Interfaces table,
    -  the 'lecMappingTable',
    -  the 'lecStatusTable',
    -  the 'lecServerVccTable',
    -  the 'lecStatisticsTable', and
    -  any other dependent tables
          
New Interfaces table rows for LAN Emulation Clients
always have 'ifAdminStatus' set to 'down'.
          
          
A Note On Indexing:
-------------------
Most of the tables in this MIB are indexed in whole
or in part by 'lecIndex' - not by 'ifIndex'.
          
Why is there a separate index?
          
Traditionally, ifIndex values are chosen by agents,
and are permitted to change across restarts.  Using
ifIndex to index lecConfigTable could complicate
row creation and/or cause interoperability problems
(if each agent had special restrictions on ifIndex).
Having a separate index avoids these problems.
lecConfigEntry row .1.3.6.1.4.1.353.5.3.1.1.1.1
Each table entry contains configuration information
for one LAN Emulation Client.

Most of the objects are derived from Initial State
Parameters in the LAN Emulation specification.
Indexes
Column Syntax OID
lecIndex
A value which uniquely identifies this conceptual
row in the lecConfigTable.

If the conceptual row identified by this value of
lecIndex is recreated following an agent restart,
the same value of lecIndex …
Integer32
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.353.5.3.1.1.1.1.1
lecRowStatus
This object lets network managers create and delete
LAN Emulation Clients, on systems that support this
optional capability.

It does not control Joins and Terminations; they are
controlled by 'ifAdminStat…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.353.5.3.1.1.1.1.2
lecOwner
The entity that configured this entry and is therefore
using the resources assigned to it.
OctetStringr/w
Constraints:
range: 0-127
 .1.3.6.1.4.1.353.5.3.1.1.1.1.3
lecConfigMode
Indicates whether this LAN Emulation Client should
auto-configure the next time it is (re)started.

In automatic(1) mode, a client uses a LAN Emulation
Configuration Server to learn the ATM address of its
…
Enumerationr/w
Enumerated Values:
1automatic
2manual
 .1.3.6.1.4.1.353.5.3.1.1.1.1.4
lecConfigLanType
C2 LAN Type.

The data frame format which this client will use the
next time it returns to the Initial State.

Auto-configuring clients use this parameter in their
Configure requests. Manua…
LecDataFrameFormatr/w
Type Values:
1unspecified
2aflane8023
3aflane8025
 .1.3.6.1.4.1.353.5.3.1.1.1.1.5
lecConfigMaxDataFrameSize
C3 Maximum Data Frame Size.

The maximum data frame size which this client will
use the next time it returns to the Initial State.

Auto-configuring clients use this parameter in their
Confi…
LecDataFrameSizer/w
Type Values:
1unspecified
2max1516
3max4544
4max9234
5max18190
 .1.3.6.1.4.1.353.5.3.1.1.1.1.6
lecConfigLanName
C5 ELAN Name.

The ELAN Name this client will use the next time it
returns to the Initial State.

Auto-configuring clients use this parameter in their
Configure requests. Manually-configure…
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.353.5.3.1.1.1.1.7
lecConfigLesAtmAddress
C9 LE Server ATM Address.

The LAN Emulation Server which this client will use
the next time it is started in manual configuration
mode.

When lecConfigMode is 'automatic', there is no need
…
AtmLaneAddressr/w
Type Constraints:
range: 0
range: 20
 .1.3.6.1.4.1.353.5.3.1.1.1.1.8
lecControlTimeout
C7 Control Time-out. Time out period used for
timing out most request/response control frame
interactions, as specified elsewhere [in the
LAN Emulation specification].

This time value is expressed in se…
secondsInteger32r/w
Constraints:
range: 10-300
 .1.3.6.1.4.1.353.5.3.1.1.1.1.9
lecMaxUnknownFrameCount
C10 Maximum Unknown Frame Count. See the description
of lecMaxUnknownFrameTime below.
framesInteger32r/w
Constraints:
range: 1-10
 .1.3.6.1.4.1.353.5.3.1.1.1.1.10
lecMaxUnknownFrameTime
C11 Maximum Unknown Frame Time. Within the period of
time defined by the Maximum Unknown Frame Time, a
LE Client will send no more than Maximum Unknown
Frame Count frames to the BUS for a given unicast
LAN Destination,…
secondsInteger32r/w
Constraints:
range: 1-60
 .1.3.6.1.4.1.353.5.3.1.1.1.1.11
lecVccTimeoutPeriod
C12 VCC Time-out Period. A LE Client SHOULD release
any Data Direct VCC that it has not used to
transmit or receive any data frames for the
length of the VCC Time-out Period. This parameter
is only meaningful for SVC …
secondsSNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.353.5.3.1.1.1.1.12
lecMaxRetryCount
C13 Maximum Retry Count. A LE CLient MUST not retry
a LE_ARP_REQUEST for a given frame's LAN
destination more than Maximum Retry Count times,
after the first LE_ARP_REQUEST for that same
frame's LAN destination.
Integer32r/w
Constraints:
range: 0-2
 .1.3.6.1.4.1.353.5.3.1.1.1.1.13
lecAgingTime
C17 Aging Time. The maximum time that a LE Client
will maintain an entry in its LE_ARP cache in
the absence of a verification of that
relationship.

This time value is expressed in seconds.
secondsInteger32r/w
Constraints:
range: 10-300
 .1.3.6.1.4.1.353.5.3.1.1.1.1.14
lecForwardDelayTime
C18 Forward Delay Time. The maximum time that a LE
Client will maintain an entry for a non-local MAC
address in its LE_ARP cache in the absence of a
verification of that relationship, as long as the
Topology Change fla…
secondsInteger32r/w
Constraints:
range: 4-30
 .1.3.6.1.4.1.353.5.3.1.1.1.1.15
lecExpectedArpResponseTime
C20 Expected LE_ARP Response Time. The maximum time
that the LEC expects an LE_ARP_REQUEST/
LE_ARP_RESPONSE cycle to take. Used for retries
and verifies.

This time value is expressed in seconds.
secondsInteger32r/w
Constraints:
range: 1-30
 .1.3.6.1.4.1.353.5.3.1.1.1.1.16
lecFlushTimeOut
C21 Flush Time-out. Time limit to wait to receive a
LE_FLUSH_RESPONSE after the LE_FLUSH_REQUEST has
been sent before taking recovery action.

This time value is expressed in seconds.
secondsInteger32r/w
Constraints:
range: 1-4
 .1.3.6.1.4.1.353.5.3.1.1.1.1.17
lecPathSwitchingDelay
C22 Path Switching Delay. The time since sending a
frame to the BUS after which the LE Client may
assume that the frame has been either discarded
or delivered to the recipient. May be used to
bypass the Flush protocol…
secondsInteger32r/w
Constraints:
range: 1-8
 .1.3.6.1.4.1.353.5.3.1.1.1.1.18
lecLocalSegmentID
C23 Local Segment ID. The segment ID of the emulated
LAN. This is only required for IEEE 802.5 clients
that are Source Routing bridges.
Integer32r/w
Constraints:
range: 0-4095
 .1.3.6.1.4.1.353.5.3.1.1.1.1.19
lecMulticastSendType
C24 Multicast Send VCC Type. Signalling parameter
that SHOULD be used by the LE Client when
establishing the Multicast Send VCC.

This is the method to be used by the LE Client
when specifying traffic par…
Enumerationr/w
Enumerated Values:
1bestEffort
2variableBitRate
3constantBitRate
 .1.3.6.1.4.1.353.5.3.1.1.1.1.20
lecMulticastSendAvgRate
C25 Multicast Send VCC AvgRate. Signalling parameter
that SHOULD be used by the LE Client when
establishing the Multicast Send VCC.

Forward and Backward Sustained Cell Rate to be
requested by LE Client w…
cells per secondSNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.353.5.3.1.1.1.1.21
lecMulticastSendPeakRate
C26 Multicast Send VCC PeakRate. Signalling parameter
that SHOULD be used by the LE Client when
establishing the Multicast Send VCC.

Forward and Backward Peak Cell Rate to be
requested by LE Client when …
cells per secondSNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.353.5.3.1.1.1.1.22
lecConnectionCompleteTimer
C28 Connection Complete Timer. Optional. In
Connection Establishment this is the time period
in which data or a READY_IND message is expected
from a Calling Party.

This time value is expressed in second…
secondsInteger32r/w
Constraints:
range: 1-10
 .1.3.6.1.4.1.353.5.3.1.1.1.1.23

lecStatusTable

table
.1.3.6.1.4.1.353.5.3.1.1.2 · 1 row entry · 16 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk lecStatusTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LAN-EMULATION-CLIENT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LAN-EMULATION-CLIENT-MIB::lecStatusTable' 
A read-only table containing identification, status,
and operational information about the LAN Emulation
Clients this agent manages.
lecStatusEntry row .1.3.6.1.4.1.353.5.3.1.1.2.1
Each table entry contains information about one LAN
Emulation Client.
Indexes
Column Syntax OID
lecIfIndex
This object identifies the logical interface number
('ifIndex') assigned to this client, and is used to
identify corresponding rows in the Interfaces MIB.

Note that re-initialization of the management age…
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.353.5.3.1.1.2.1.1
lecPrimaryAtmAddress
C1 LE Client's ATM Addresses.

The primary ATM address of this LAN Emulation Client.
This address is used to establish the Control Direct
and Multicast Send VCCs, and may also be used to set
up Data Direc…
AtmLaneAddress
Type Constraints:
range: 0
range: 20
 .1.3.6.1.4.1.353.5.3.1.1.2.1.2
lecID
C14 LE Client Identifier. Each LE Client requires a
LE Client Identifier (LECID) assigned by the LE
Server during the Join phase. The LECID is placed
in control requests by the LE Client and MAY be
used for echo suppr…
Integer32
Constraints:
range: 0-65279
 .1.3.6.1.4.1.353.5.3.1.1.2.1.3
lecInterfaceState
The current state of the LAN Emulation Client.

Note that 'ifOperStatus' is defined to be 'up' when,
and only when, 'lecInterfaceState' is 'operational'.
LecState
Type Values:
1initialState
2lecsConnect
3configure
4join
5initialRegistration
6busConnect
7operational
 .1.3.6.1.4.1.353.5.3.1.1.2.1.4
lecLastFailureRespCode
Status code from the last failed Configure response
or Join response. Failed responses are those for
which the LE_CONFIGURE_RESPONSE / LE_JOIN_RESPONSE
frame contains a non-zero code, or fails to arrive
within a timeou…
Enumeration
Enumerated Values:
1none
2timeout
3undefinedError
4versionNotSupported
5invalidRequestParameters
6duplicateLanDestination
7duplicateAtmAddress
8insufficientResources
9accessDenied
10invalidRequesterId
11invalidLanDestination
12invalidAtmAddress
13noConfiguration
14leConfigureError
15insufficientInformation
 .1.3.6.1.4.1.353.5.3.1.1.2.1.5
lecLastFailureState
The state this client was in when it updated the
'lecLastFailureRespCode'.

If 'lecLastFailureRespCode' is 'none', this object
has the value initialState(1).
LecState
Type Values:
1initialState
2lecsConnect
3configure
4join
5initialRegistration
6busConnect
7operational
 .1.3.6.1.4.1.353.5.3.1.1.2.1.6
lecProtocol
The LAN Emulation protocol which this client supports,
and specifies in its LE_JOIN_REQUESTs.
Integer32
Constraints:
range: 1-255
 .1.3.6.1.4.1.353.5.3.1.1.2.1.7
lecVersion
The LAN Emulation protocol version which this client
supports, and specifies in its LE_JOIN_REQUESTs.
Integer32
Constraints:
range: 1-255
 .1.3.6.1.4.1.353.5.3.1.1.2.1.8
lecTopologyChange
C19 Topology Change. Boolean indication that the LE
Client is using the Forward Delay Time C18,
instead of the Aging Time C17, to age non-local
entries in its LE_ARP cache C16.

For a client which is not …
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.353.5.3.1.1.2.1.9
lecConfigServerAtmAddress
The ATM address of the LAN Emulation Configuration
Server (if known) or the empty string (otherwise).
AtmLaneAddress
Type Constraints:
range: 0
range: 20
 .1.3.6.1.4.1.353.5.3.1.1.2.1.10
lecConfigSource
Indicates whether this LAN Emulation Client used the
LAN Emulation Configuration Server, and, if so, what
method it used to establish the Configuration Direct
VCC.
Enumeration
Enumerated Values:
1gotAddressViaIlmi
2usedWellKnownAddress
3usedLecsPvc
4didNotUseLecs
 .1.3.6.1.4.1.353.5.3.1.1.2.1.11
lecActualLanType
C2 LAN Type.

The data frame format that this LAN Emulation Client
is using right now. This may come from

* lecConfigLanType,
* the LAN Emulation Configuration Server, or
* …
LecDataFrameFormat
Type Values:
1unspecified
2aflane8023
3aflane8025
 .1.3.6.1.4.1.353.5.3.1.1.2.1.12
lecActualMaxDataFrameSize
C3 Maximum Data Frame Size.

The maximum data frame size that this LAN Emulation
client is using right now. This may come from

* lecConfigMaxDataFrameSize,
* the LAN Emulation Co…
LecDataFrameSize
Type Values:
1unspecified
2max1516
3max4544
4max9234
5max18190
 .1.3.6.1.4.1.353.5.3.1.1.2.1.13
lecActualLanName
C5 ELAN Name.

The identity of the emulated LAN which this client
last joined, or wishes to join. This may come from

* lecConfigLanName,
* the LAN Emulation Configuration Server,…
OctetString
Constraints:
range: 0-32
 .1.3.6.1.4.1.353.5.3.1.1.2.1.14
lecActualLesAtmAddress
C9 LE Server ATM Address.

The LAN Emulation Server address currently in use or
most recently attempted.

If no LAN Emulation Server attachment has been tried,
this object's value is the zer…
AtmLaneAddress
Type Constraints:
range: 0
range: 20
 .1.3.6.1.4.1.353.5.3.1.1.2.1.15
lecProxyClient
C4 Proxy.

Indicates whether this client is acting as a proxy.

Proxy clients are allowed to represent unregistered
MAC addresses, and receive copies of LE_ARP_REQUEST
frames for such addres…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.353.5.3.1.1.2.1.16

lecMappingTable

table
.1.3.6.1.4.1.353.5.3.1.1.3 · 1 row entry · 1 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk lecMappingTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LAN-EMULATION-CLIENT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LAN-EMULATION-CLIENT-MIB::lecMappingTable' 
A table mapping the 'ifIndex' values of 'aflane8023'
and 'aflane8025' interfaces to the 'lecIndex' values
of the corresponding LAN Emulation Clients.
lecMappingEntry row .1.3.6.1.4.1.353.5.3.1.1.3.1
Each row describes one ifIndex --> lecIndex mapping.
Indexes
Column Syntax OID
lecMappingIndex
The 'lecIndex' of the client which implements the
specified interface.
Integer32
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.353.5.3.1.1.3.1.1

lecStatisticsTable

table
.1.3.6.1.4.1.353.5.3.1.1.4 · 1 row entry · 7 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk lecStatisticsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LAN-EMULATION-CLIENT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LAN-EMULATION-CLIENT-MIB::lecStatisticsTable' 
An extension table containing traffic statistics for
all the LAN Emulation Clients this host implements.
lecStatisticsEntry row .1.3.6.1.4.1.353.5.3.1.1.4.1
Each row in this table contains traffic statistics
for one LAN Emulation client.
Indexes
Column Syntax OID
lecArpRequestsOut
The number of LE_ARP_REQUESTs sent over the LUNI by
this LAN Emulation Client.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.353.5.3.1.1.4.1.1
lecArpRequestsIn
The number of LE_ARP_REQUESTs received over the LUNI
by this LAN Emulation Client.

Requests may arrive on the Control Direct VCC or on
the Control Distribute VCC, depending upon how the
LES is implemented…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.353.5.3.1.1.4.1.2
lecArpRepliesOut
The number of LE_ARP_RESPONSEs sent over the LUNI by
this LAN Emulation Client.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.353.5.3.1.1.4.1.3
lecArpRepliesIn
The number of LE_ARP_RESPONSEs received over the LUNI
by this LAN Emulation Client. This count includes
all such replies, whether solicited or not.

Replies may arrive on the Control Direct VCC or on
the …
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.353.5.3.1.1.4.1.4
lecControlFramesOut
The total number of control packets sent by this
LAN Emulation Client over the LUNI.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.353.5.3.1.1.4.1.5
lecControlFramesIn
The total number of control packets received by this
LAN Emulation Client over the LUNI.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.353.5.3.1.1.4.1.6
lecSvcFailures
The total number of

* outgoing LAN Emulation SVCs which this client
tried, but failed, to open;

* incoming LAN Emulation SVCs which this client
tried, but failed to establish; and
…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.353.5.3.1.1.4.1.7

lecServerVccTable

table
.1.3.6.1.4.1.353.5.3.1.1.5 · 1 row entry · 15 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk lecServerVccTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LAN-EMULATION-CLIENT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LAN-EMULATION-CLIENT-MIB::lecServerVccTable' 
A table identifying the Control and Multicast VCCs
for each LAN Emulation Client this host implements.
lecServerVccEntry row .1.3.6.1.4.1.353.5.3.1.1.5.1
Each row in this table describes the Control VCCs
and Multicast VCCs for one LAN Emulation client.
Indexes
Column Syntax OID
lecConfigDirectInterface
The interface associated with the Configuration
Direct VCC. If no Configuration Direct VCC exists,
this object has the value 0. Otherwise, the objects

( lecConfigDirectInterface,
lecConfigDire…
LeConnectionInterface
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.353.5.3.1.1.5.1.1
lecConfigDirectVpi
If the Configuration Direct VCC exists, this object
contains the VPI which identifies that VCC at
the point where it connects to this LE client.

Otherwise, this object has the value 0.
VpiInteger
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.353.5.3.1.1.5.1.2
lecConfigDirectVci
If the Configuration Direct VCC exists, this object
contains the VCI which identifies that VCC at
the point where it connects to this LE client.

Otherwise, this object has the value 0.
VciInteger
Type Constraints:
range: 0..65535
 .1.3.6.1.4.1.353.5.3.1.1.5.1.3
lecControlDirectInterface
The interface associated with the Control Direct VCC.
If no Control Direct VCC exists, this object has the
value 0. Otherwise, the objects

( lecControlDirectInterface,
lecControlDirectVpi, lecC…
LeConnectionInterface
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.353.5.3.1.1.5.1.4
lecControlDirectVpi
If the Control Direct VCC exists, this object
contains the VPI which identifies that VCC at
the point where it connects to this LE client.

Otherwise, this object has the value 0.
VpiInteger
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.353.5.3.1.1.5.1.5
lecControlDirectVci
If the Control Direct VCC exists, this object
contains the VCI which identifies that VCC at
the point where it connects to this LE client.

Otherwise, this object has the value 0.
VciInteger
Type Constraints:
range: 0..65535
 .1.3.6.1.4.1.353.5.3.1.1.5.1.6
lecControlDistributeInterface
The interface associated with the Control Distribute
VCC. If no Control Distribute VCC has been set up to
this client, this object has the value 0. Otherwise,
the objects

( lecControlDistributeInter…
LeConnectionInterface
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.353.5.3.1.1.5.1.7
lecControlDistributeVpi
If the Control Distribute VCC exists, this object
contains the VPI which identifies that VCC at the
point where it connects to this LE client.

Otherwise, this object has the value 0.
VpiInteger
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.353.5.3.1.1.5.1.8
lecControlDistributeVci
If the Control Distribute VCC exists, this object
contains the VCI which identifies that VCC at the
point where it connects to this LE client.

Otherwise, this object contains the value 0.
VciInteger
Type Constraints:
range: 0..65535
 .1.3.6.1.4.1.353.5.3.1.1.5.1.9
lecMulticastSendInterface
The interface associated with the Multicast Send
VCC. If no Multicast Send VCC exists, this object
has the value 0. Otherwise, the objects

( lecMulticastSendInterface,
lecMulticastSendVpi, lec…
LeConnectionInterface
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.353.5.3.1.1.5.1.10
lecMulticastSendVpi
If the Multicast Send VCC exists, this object
contains the VPI which identifies that VCC at
the point where it connects to this LE client.

Otherwise, this object has the value 0.
VpiInteger
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.353.5.3.1.1.5.1.11
lecMulticastSendVci
If the Multicast Send VCC exists, this object
contains the VCI which identifies that VCC at
the point where it connects to this LE client.

Otherwise, this object has the value 0.
VciInteger
Type Constraints:
range: 0..65535
 .1.3.6.1.4.1.353.5.3.1.1.5.1.12
lecMulticastForwardInterface
The interface associated with the Multicast Forward
VCC. If no Multicast Forward VCC has been set up to
this client, this object has the value 0. Otherwise,
the objects

( lecMulticastForwardInterfac…
LeConnectionInterface
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.353.5.3.1.1.5.1.13
lecMulticastForwardVpi
If the Multicast Forward VCC exists, this object
contains the VPI which identifies that VCC at the
point where it connects to this LE client.

Otherwise, this object has the value 0.
VpiInteger
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.353.5.3.1.1.5.1.14
lecMulticastForwardVci
If the Multicast Forward VCC exists, this object
contains the VCI which identifies that VCC at the
point where it connects to this LE client.

Otherwise, this object has the value 0.
VciInteger
Type Constraints:
range: 0..65535
 .1.3.6.1.4.1.353.5.3.1.1.5.1.15

lecAtmAddressTable

table
.1.3.6.1.4.1.353.5.3.1.1.6 · 1 row entry · 2 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk lecAtmAddressTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LAN-EMULATION-CLIENT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LAN-EMULATION-CLIENT-MIB::lecAtmAddressTable' 
A table listing all of the ATM addresses belonging
to this host's LAN Emulation Clients.
lecAtmAddressEntry row .1.3.6.1.4.1.353.5.3.1.1.6.1
Each row in this table describes one of a client's
ATM addresses.
Indexes
Column Syntax OID
lecAtmAddress
The ATM address this row describes. This could be
either a primary address or a secondary address.
AtmLaneAddress
Type Constraints:
range: 0
range: 20
 .1.3.6.1.4.1.353.5.3.1.1.6.1.1
lecAtmAddressStatus
Used to create and delete rows in this table.

A management station may not change the status of a
primary ATM address to 'notInService' or 'destroy'
unless the client's ifAdminStatus is 'down', and the
cl…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.353.5.3.1.1.6.1.2

lecMacAddressTable

table
.1.3.6.1.4.1.353.5.3.1.1.7 · 1 row entry · 2 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk lecMacAddressTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LAN-EMULATION-CLIENT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LAN-EMULATION-CLIENT-MIB::lecMacAddressTable' 
This table contains entries for all of the registered
MAC addresses belonging to this agent's LE clients.
          
C6  Local Unicast MAC Address(es).  Each LE Client has
    zero or more local unicast MAC addresses.  In an
    operational LE Client, every address in this
    variable MUST have been registered with the LE
    Server.  Two LE CLients joined to the same
    emulated LAN MUST NOT have the same local unicast
    MAC address.  A LE Client's MAC addresses may
    change during normal operations.  When answering
    a LE_ARP_REQUEST for any address in this list, the
    'Remote Address' bit in the FLAGS field of the
    LE_ARP_RESPONSE MUST be clear.
lecMacAddressEntry row .1.3.6.1.4.1.353.5.3.1.1.7.1
Each table row describes a (MAC address, ATM address)
pair registered for a particular client.
Indexes
Column Syntax OID
lecMacAddress
A unicast MAC address which the LE client denoted by
'lecIndex' has registered with its LE Server.
SNMPv2-TCMacAddress
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
 .1.3.6.1.4.1.353.5.3.1.1.7.1.1
lecMacAddressAtmBinding
The ATM address registered for 'lecMacAddress'.
AtmLaneAddress
Type Constraints:
range: 0
range: 20
 .1.3.6.1.4.1.353.5.3.1.1.7.1.2

lecRouteDescrTable

table
.1.3.6.1.4.1.353.5.3.1.1.8 · 1 row entry · 3 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk lecRouteDescrTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LAN-EMULATION-CLIENT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LAN-EMULATION-CLIENT-MIB::lecRouteDescrTable' 
This table lists all of the Route Descriptors which
are registered by this host's LAN Emulation Clients.
          
C8  Route Descriptor(s).  Route Descriptors exist only
    for source-routed IEEE 802.5 LE Clients that are
    Source-Route Bridges.  All Route Descriptors in
    any given emulated LAN MUST be unique.  A LE
    Client MAY have zero or more Route Descriptors
    and these Route Descriptors MAY change during
    normal operation.  In an operational LE Client,
    every Local Route Descriptor in C8 MUST have been
    registered with the LE Server.  When answering a
    LE_ARP_REQUEST for any address in this list, the
    'Remote Address' bit in the FLAGS field of the
    LE_ARP_RESPONSE MUST be clear.
lecRouteDescrEntry row .1.3.6.1.4.1.353.5.3.1.1.8.1
Each table row describes a (Route Descriptor, ATM
address) pair registered for a particular client.
Indexes
Column Syntax OID
lecRouteDescrSegmentID
The LAN ID portion of the IEEE 802.5 route descriptor
associated with this conceptual row.
Integer32
Constraints:
range: 0-4095
 .1.3.6.1.4.1.353.5.3.1.1.8.1.1
lecRouteDescrBridgeNumber
The Bridge Number portion of the IEEE 802.5 route
descriptor associated with this conceptual row.
Integer32
Constraints:
range: 0-15
 .1.3.6.1.4.1.353.5.3.1.1.8.1.2
lecRouteDescrAtmBinding
The ATM address registered for the IEEE 802.5 route
descriptor ('lecRouteDescrSegmentID',
'lecRouteDescrBridgeNumber').
AtmLaneAddress
Type Constraints:
range: 0
range: 20
 .1.3.6.1.4.1.353.5.3.1.1.8.1.3

leArpTable

table
.1.3.6.1.4.1.353.5.3.1.1.9 · 1 row entry · 5 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk leArpTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LAN-EMULATION-CLIENT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LAN-EMULATION-CLIENT-MIB::leArpTable' 
This table provides access to an ATM LAN Emulation
Client's MAC-to-ATM ARP cache.  It contains entries
for unicast addresses and for the broadcast address,
but not for multicast MAC addresses.
          
C16 LE_ARP Cache.  A table of entries, each of which
    establishes a relationship between a LAN
    Destination external to the LE Client and the
    ATM address to which data frames for that LAN
    Destination will be sent.
leArpEntry row .1.3.6.1.4.1.353.5.3.1.1.9.1
An ATM LAN Emulation ARP cache entry containing
information about the binding of one MAC address
to one ATM address.
Indexes
Column Syntax OID
leArpMacAddress
The MAC address for which this cache entry provides
a translation. Since ATM LAN Emulation uses an ARP
protocol to locate the Broadcast and Unknown Server,
the value of this object could be the broadcast MAC
address.
…
SNMPv2-TCMacAddress
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
 .1.3.6.1.4.1.353.5.3.1.1.9.1.1
leArpAtmAddress
The ATM address of the Broadcast & Unknown Server
or LAN Emulation Client whose MAC address is stored
in 'leArpMacAddress'.

This value may be determined through the use of the
LE_ARP procedure, through so…
AtmLaneAddressr/w
Type Constraints:
range: 0
range: 20
 .1.3.6.1.4.1.353.5.3.1.1.9.1.2
leArpIsRemoteAddress
Indicates whether this entry is for a local or remote
MAC address.

In this context, 'local' means 'a MAC address that is
local to the remote client', as opposed to 'one of my
addresses'.

…
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.353.5.3.1.1.9.1.3
leArpEntryType
Indicates how this LE_ARP table entry was created and
whether it is aged.
LeArpTableEntryTyper/w
Type Values:
1other
2learnedViaControl
3learnedViaData
4staticVolatile
5staticNonVolatile
 .1.3.6.1.4.1.353.5.3.1.1.9.1.4
leArpRowStatus
Lets users create and delete LE_ARP cache entries,
on systems that support this capability.

Normally clients will maintain their LE_ARP caches
automatically. However, managers may occasionally
want to cr…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.353.5.3.1.1.9.1.5

leRDArpTable

table
.1.3.6.1.4.1.353.5.3.1.1.10 · 1 row entry · 5 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk leRDArpTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LAN-EMULATION-CLIENT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LAN-EMULATION-CLIENT-MIB::leRDArpTable' 
This table provides access to an ATM LAN Emulation
Client's Route Descriptor-to-ATM ARP cache.
          
Implementation of this table is optional for hosts
that do not support emulated IEEE 802.5 Token Ring
LANs, and mandatory for hosts which do.
          
C16 LE_ARP Cache.  A table of entries, each of which
    establishes a relationship between a LAN
    Destination external to the LE Client and the
    ATM address to which data frames for that LAN
    Destination will be sent.
leRDArpEntry row .1.3.6.1.4.1.353.5.3.1.1.10.1
An ATM LAN Emulation ARP cache entry containing
information about the binding of one IEEE 802.5
route descriptor to one ATM address.
Indexes
Column Syntax OID
leRDArpSegmentID
The LAN ID portion of the IEEE 802.5 route descriptor
associated with this ARP cache entry.
Integer32
Constraints:
range: 0-4095
 .1.3.6.1.4.1.353.5.3.1.1.10.1.1
leRDArpBridgeNumber
The Bridge Number portion of the IEEE 802.5 route
descriptor associated with this ARP cache entry.
Integer32
Constraints:
range: 0-15
 .1.3.6.1.4.1.353.5.3.1.1.10.1.2
leRDArpAtmAddress
The ATM address of the LAN Emulation Client which is
associated with the route descriptor
('leRDArpSegmentID', 'leRDArpBridgeNumber').

This value may be determined through the use of the
LE_ARP procedure,…
AtmLaneAddressr/w
Type Constraints:
range: 0
range: 20
 .1.3.6.1.4.1.353.5.3.1.1.10.1.3
leRDArpEntryType
Indicates how this LE_ARP table entry was created and
whether it is aged.
LeArpTableEntryTyper/w
Type Values:
1other
2learnedViaControl
3learnedViaData
4staticVolatile
5staticNonVolatile
 .1.3.6.1.4.1.353.5.3.1.1.10.1.4
leRDArpRowStatus
Lets users create and delete LE_ARP cache entries,
on systems that support this capability.

Normally clients will maintain their LE_ARP caches
automatically. However, managers may occasionally
want to cr…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.353.5.3.1.1.10.1.5