JUNIPER-PW-TDM-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
5
Rows
5
Columns
62

jnxpwTDMTable

table
.1.3.6.1.4.1.2636.3.54.1.1.1 · 1 row entry · 9 columns
Open in standard view 
This table contains basic information including ifIndex,
and pointers to entries in the relevant TDM config
tables for this TDM PW.
jnxpwTDMEntry entry .1.3.6.1.4.1.2636.3.54.1.1.1.1
This table is indexed by the same index that was
created for the associated entry in the PW Table
(in the PW-STD-MIB).

- The PwIndex.

An entry is created in this table by the agent for every
…
Indexes
JUNIPER-VPN-MIBjnxVpnPwVpnType JUNIPER-VPN-MIBjnxVpnPwVpnName JUNIPER-VPN-MIBjnxVpnPwIndex
Column Syntax OID
jnxpwTDMRate
The parameter represents the bit-rate of the TDM service
in multiples of the 'basic' 64 Kbit/s rate [TDMCP-EXT].
It complements the definition of pwType used in
PW-STD-MIB.
For structure-agnostic the following should be…
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2636.3.54.1.1.1.1.1
jnxpwTDMIfIndex
This is a unique index within the ifTable. It represents
the interface index of the full link or the interface
index for the bundle holding the group of
time slots to be transmitted via this PW connection.
…
IF-MIBInterfaceIndexOrZero
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.2636.3.54.1.1.1.1.2
jnxpwGenTDMCfgIndex
Index to the generic parameters in the TDM configuration
table that appears in this MIB module. It is likely that
multiple TDM PWs of the same characteristic will share
a single TDM Cfg entry.
JnxPwCfgIndexOrzero
Textual Convention: JnxPwCfgIndexOrzero Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.1.1.3
jnxpwRelTDMCfgIndex
Index to the relevant TDM configuration table entry
that appears in one of the related MIB modules
such as TDMoIP or CESoPSN. It is likely that
multiple TDM PWs of the same characteristic will share
a single configurati…
JnxPwCfgIndexOrzero
Textual Convention: JnxPwCfgIndexOrzero Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.1.1.4
jnxpwTDMConfigError
Any of the bits are set if the local configuration is
not compatible with the peer configuration as available
from the various parameters options. Setting is done based
on signaling, or else value (0) will be set.
…
Bits
Enumerated Values:
0notApplicable
1tdmTypeIncompatible
2peerRtpIncompatible
3peerPayloadSizeIncompatible
 .1.3.6.1.4.1.2636.3.54.1.1.1.1.5
jnxpwTDMTimeElapsed
The number of seconds, including partial seconds,
that have elapsed since the beginning of the current
measurement period. If, for some reason, such as an
adjustment in the system's time-of-day clock, the
current interv…
Integer32
Constraints:
range: 1-900
 .1.3.6.1.4.1.2636.3.54.1.1.1.1.6
jnxpwTDMValidIntervals
The number of previous 15-minute intervals for which data
was collected.
An agent with TDM capability must be capable of supporting
at least n intervals. The minimum value of n is 4, The
default of n is 32 and the maxim…
Integer32
Constraints:
range: 0-96
 .1.3.6.1.4.1.2636.3.54.1.1.1.1.7
jnxpwTDMValidDayIntervals
The number of previous days for which data
was collected.
An agent with TDM capability must be capable of supporting
at least n intervals. The minimum value of n is 1, The
default of n is 1 and the maximum value of n is…
Integer32
Constraints:
range: 0-30
 .1.3.6.1.4.1.2636.3.54.1.1.1.1.8
jnxpwTDMLastEsTimeStamp
The value of sysUpTime at the most recent occasion at
which the TDM PW entered the ES or SES state.
SNMPv2-TCTimeStamp
Textual Convention: SNMPv2-TCTimeStamp Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.1.1.11

jnxpwTDMCfgTable

table
.1.3.6.1.4.1.2636.3.54.1.1.3 · 1 row entry · 20 columns
Open in standard view 
This table contains a set of parameters that may be
referenced by one or more TDM PWs in pwTDMTable.
jnxpwTDMCfgEntry entry .1.3.6.1.4.1.2636.3.54.1.1.3.1
These parameters define the characteristics of a
TDM PW. They are grouped here to ease NMS burden.
Once an entry is created here it may be re-used
by many PWs.
Unless otherwise specified, all objects in this table
MUST …
Indexes
JUNIPER-VPN-MIBjnxVpnPwVpnType JUNIPER-VPN-MIBjnxVpnPwVpnName JUNIPER-VPN-MIBjnxVpnPwIndex
Column Syntax OID
jnxpwTDMCfgIndex
Index to an entry in this table. The value is a copy of the
assigned pwTDMCfgIndexNext
JnxPwTDMCfgIndex
Textual Convention: JnxPwTDMCfgIndex Unsigned32
Type Constraints:
range: 1..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.1
jnxpwTDMCfgRowStatus
Object used for creating, modifying, and deleting
a row from this table. The following objects should not be
modified if the entry is in used and the status is active:
pwTDMCfgPayloadSize, pwTDMCfgRtpHdrUsed,
pwTDMCfgJt…
SNMPv2-TCRowStatus
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.2
jnxpwTDMCfgPayloadSize
The value of this object indicates the PayLoad Size (in bytes)
to be defined during the PW setUp. Upon TX, implementation
must be capable of carrying that amount of bytes.
Upon RX, when the LEN field is set to 0, the pa…
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.4
jnxpwTDMCfgPktReorder
If set True: as CE bound packets are queued in the
jitter buffer, out of order packets are re-ordered. The
maximum sequence number differential (i.e., the range in
which re-sequencing can occur) is dependant on the dept…
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.5
jnxpwTDMCfgRtpHdrUsed
If set to False: an RTP header is not pre-pended to the
TDM packet.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.6
jnxpwTDMCfgJtrBfrDepth
The size of this buffer SHOULD be locally
configured to allow accommodation to the PSN-specific packet
delay variation.

If configured to a value not supported by the
implementation, the agent MUST return …
microsecondSNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.7
jnxpwTDMCfgPayloadSuppression
Selecting 'enable' means: Payload suppression is allowed.
Payload MAY be omitted in order to conserve bandwidth.
Selecting 'disable' means: no suppresion under any
condition.
Object MAY be changed at any time.
Enumeration
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.8
jnxpwTDMCfgConsecPktsInSynch
The number of consecutive packets with sequential
sequence numbers that are required to exit the
LOPS state.
Object MAY be changed when the related PW is
defined as not active.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.9
jnxpwTDMCfgConsecMissPktsOutSynch
The number of consecutive missing packets that are
required to enter the LOPS state.
Object MAY be changed when the related PW is
defined as not active.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.10
jnxpwTDMCfgSetUp2SynchTimeOut
The amount of time the host should wait before declaring the
pseudo wire in down state, if the number of consecutive
TDM packets that have been received after changing the
adminstrative status to up and after finalizat…
millisecondSNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.11
jnxpwTDMCfgPktReplacePolicy
This parameter determines the value to be played when CE bound
packets have over/underflow the jitter buffer, or are missing
for any reason. This byte pattern is sent(played)on
the TDM line. Selecting implementationSpec…
Enumeration
Enumerated Values:
1allOnes
2implementationSpecific
3filler
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.12
jnxpwTDMCfgAvePktLossTimeWindow
The length of time over which the average packet
loss rate should be computed to detect Excessive packet
loss rate.
Object MAY be changed when the related PW is
defined as not active.
millisecondSNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.13
jnxpwTDMCfgExcessivePktLossThreshold
Excessive packet loss rate is detected by computing the
average packetloss rate over a pwTDMCfgAvePktLossTimeWindow
amount of time and comparing it with this threshold value.
The rate is expressed in precentage.
Object …
PercentSNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.14
jnxpwTDMCfgAlarmThreshold
Alarms are only reported when the defect state persists
for the length of time specified by this object.
The object's unit is millisec.
Object MAY be changed when the related PW is
defined as not active.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.15
jnxpwTDMCfgClearAlarmThreshold
Alarm MUST be cleared after the corresponding defect is
undetected for the amount of time specified by this object.
The object's unit is millisec.
Object MAY be changed when the related PW is
defined as not active.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.16
jnxpwTDMCfgMissingPktsToSes
Percent of missing packets detected (consecutive or not)
within a 1 second window to cause a Severely Error
Second (SES) to be counted.
Object MAY be changed when the related PW is
defined as not active.
PercentSNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.17
jnxpwTDMCfgTimestampMode
Timestamp generation MAY be used in one of the following
modes:
1. Absolute mode: the PSN-bound IWF sets timestamps
using the clock recovered from the incoming TDM attachment
circuit. As a consequence, the timestamps …
Enumeration
Enumerated Values:
1notApplicable
2absolute
3differential
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.18
jnxpwTDMCfgStorageType
This variable indicates the storage type for this
row.
SNMPv2-TCStorageType
Textual Convention: SNMPv2-TCStorageType Enumeration
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.19
jnxpwTDMCfgPktFiller
Filler byte pattern played out on the TDM
interface if pwTDMCfgPktReplacePolicy
was set to filler(3).
Object MAY be changed when the related PW is
defined as not active.
Unsigned32
Constraints:
range: 0-255
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.20
jnxpwTDMCfgName
A descriptive string, prefereably unique name, to an entry
in this table.
Object MAY be changed at any time.
SNMP-FRAMEWORK-MIBSnmpAdminString
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.2636.3.54.1.1.3.1.21

jnxpwTDMPerfCurrentTable

table
.1.3.6.1.4.1.2636.3.54.1.1.5 · 1 row entry · 9 columns
Open in standard view 
The current 15 minute interval counts are in
this table.
          
This table provides per TDM PW performance information.
jnxpwTDMPerfCurrentEntry entry .1.3.6.1.4.1.2636.3.54.1.1.5.1
An entry in this table is created by the agent for every
pwTDMTable entry. After 15 minutes, the contents of this
table entry are copied to a new entry in the
pwTDMPerfInterval table and the counts in this entry
are res…
Indexes
JUNIPER-VPN-MIBjnxVpnPwVpnType JUNIPER-VPN-MIBjnxVpnPwVpnName JUNIPER-VPN-MIBjnxVpnPwIndex
Column Syntax OID
jnxpwTDMPerfCurrentMissingPkts
Number of missing packets (as detected via control word
sequence number gaps).
PerfHist-TC-MIBPerfCurrentCount
Textual Convention: PerfHist-TC-MIBPerfCurrentCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.5.1.1
jnxpwTDMPerfCurrentPktsReOrder
Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this Feature.
PerfHist-TC-MIBPerfCurrentCount
Textual Convention: PerfHist-TC-MIBPerfCurrentCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.5.1.2
jnxpwTDMPerfCurrentJtrBfrUnderruns
Number of times a packet needed to be played
out and the jitter buffer was empty.
PerfHist-TC-MIBPerfCurrentCount
Textual Convention: PerfHist-TC-MIBPerfCurrentCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.5.1.3
jnxpwTDMPerfCurrentMisOrderDropped
Number of packets detected out of order(via control word
sequence numbers), and could not be re-ordered, or could
not fit in the jitter buffer.
PerfHist-TC-MIBPerfCurrentCount
Textual Convention: PerfHist-TC-MIBPerfCurrentCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.5.1.4
jnxpwTDMPerfCurrentMalformedPkt
Number of packets detected with unexpected size, or
bad headers' stack
PerfHist-TC-MIBPerfCurrentCount
Textual Convention: PerfHist-TC-MIBPerfCurrentCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.5.1.5
jnxpwTDMPerfCurrentESs
The counter associated with the number of Error
Seconds encountered. Any malformed packet, seq. error, LOPS
and similar are considered as error second
PerfHist-TC-MIBPerfCurrentCount
Textual Convention: PerfHist-TC-MIBPerfCurrentCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.5.1.6
jnxpwTDMPerfCurrentSESs
The counter associated with the number of
Severely Error Seconds encountered.
PerfHist-TC-MIBPerfCurrentCount
Textual Convention: PerfHist-TC-MIBPerfCurrentCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.5.1.7
jnxpwTDMPerfCurrentUASs
The counter associated with the number of
Unavailable Seconds encountered. Any consequtive
ten seconds of SES are counted as one UAS
PerfHist-TC-MIBPerfCurrentCount
Textual Convention: PerfHist-TC-MIBPerfCurrentCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.5.1.8
jnxpwTDMPerfCurrentFC
TDM Failure Counts (FC-TDM). The number of TDM failure
events. A failure event begins when the LOPS failure
is declared, and ends when the failure is cleared. A
failure event that begins in one period and ends in
anothe…
PerfHist-TC-MIBPerfCurrentCount
Textual Convention: PerfHist-TC-MIBPerfCurrentCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.5.1.9

jnxpwTDMPerfIntervalTable

table
.1.3.6.1.4.1.2636.3.54.1.1.6 · 1 row entry · 12 columns
Open in standard view 
This table provides performance information per TDM PW
similar to the pwTDMPerfCurrentTable above. However,
these counts represent historical 15 minute intervals.
Typically, this table will have a maximum of 96 entries
for a 24 hour period, but is not limited to this.
jnxpwTDMPerfIntervalEntry entry .1.3.6.1.4.1.2636.3.54.1.1.6.1
An entry in this table is created by the agent for
every pwTDMPerfCurrentEntry that is 15 minutes old.
The contents of the Current entry are copied to the new
entry here. The Current entry, then resets its counts
to zer…
Indexes
JUNIPER-VPN-MIBjnxVpnPwVpnType JUNIPER-VPN-MIBjnxVpnPwVpnName JUNIPER-VPN-MIBjnxVpnPwIndex jnxpwTDMPerfIntervalNumber
Column Syntax OID
jnxpwTDMPerfIntervalNumber
A number (normally between 1 and 96 to cover a 24 hour
period) which identifies the interval for which the set
of statistics is available. The interval identified by 1
is the most recently completed 15 minute interval, …
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.1
jnxpwTDMPerfIntervalValidData
This variable indicates if the data for this interval
is valid.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.2
jnxpwTDMPerfIntervalDuration
The duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.3
jnxpwTDMPerfIntervalMissingPkts
Number of missing packets (as detected via control
word sequence number gaps).
PerfHist-TC-MIBPerfIntervalCount
Textual Convention: PerfHist-TC-MIBPerfIntervalCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.4
jnxpwTDMPerfIntervalPktsReOrder
Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
Feature.
PerfHist-TC-MIBPerfIntervalCount
Textual Convention: PerfHist-TC-MIBPerfIntervalCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.5
jnxpwTDMPerfIntervalJtrBfrUnderruns
Number of times a packet needed to be played
out and the jitter buffer was empty.
PerfHist-TC-MIBPerfIntervalCount
Textual Convention: PerfHist-TC-MIBPerfIntervalCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.6
jnxpwTDMPerfIntervalMisOrderDropped
Number of packets detected out of order(via control word
sequence numbers), and could not be re-ordered, or could
not fit in the jitter buffer.
PerfHist-TC-MIBPerfIntervalCount
Textual Convention: PerfHist-TC-MIBPerfIntervalCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.7
jnxpwTDMPerfIntervalMalformedPkt
Number of packets detected with unexpected size, or
bad headers' stack
PerfHist-TC-MIBPerfIntervalCount
Textual Convention: PerfHist-TC-MIBPerfIntervalCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.8
jnxpwTDMPerfIntervalESs
The counter associated with the number of Error
Seconds encountered.
PerfHist-TC-MIBPerfIntervalCount
Textual Convention: PerfHist-TC-MIBPerfIntervalCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.9
jnxpwTDMPerfIntervalSESs
The counter associated with the number of
Severely Error Seconds encountered.
PerfHist-TC-MIBPerfIntervalCount
Textual Convention: PerfHist-TC-MIBPerfIntervalCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.10
jnxpwTDMPerfIntervalUASs
The counter associated with the number of
Unavailable Seconds encountered.
PerfHist-TC-MIBPerfIntervalCount
Textual Convention: PerfHist-TC-MIBPerfIntervalCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.11
jnxpwTDMPerfIntervalFC
TDM Failure Counts (FC-TDM). The number of TDM failure
events. A failure event begins when the LOPS failure
is declared, and ends when the failure is cleared. A
failure event that begins in one period and ends in
anothe…
PerfHist-TC-MIBPerfIntervalCount
Textual Convention: PerfHist-TC-MIBPerfIntervalCount Unsigned32
 .1.3.6.1.4.1.2636.3.54.1.1.6.1.12

jnxpwTDMPerf1DayIntervalTable

table
.1.3.6.1.4.1.2636.3.54.1.1.7 · 1 row entry · 12 columns
Open in standard view 
This table provides performance information per TDM PW
similar to the pwTDMPerfIntervalTable above. However,
these counters represent historical 1 day intervals up to
one full month. The table consists of real time data, as
such it is not persistence across re-boot.
jnxpwTDMPerf1DayIntervalEntry entry .1.3.6.1.4.1.2636.3.54.1.1.7.1
An entry is created in this table by the agent
for every entry in the pwTDMTable table.
Indexes
JUNIPER-VPN-MIBjnxVpnPwVpnType JUNIPER-VPN-MIBjnxVpnPwVpnName JUNIPER-VPN-MIBjnxVpnPwIndex jnxpwTDMPerf1DayIntervalNumber
Column Syntax OID
jnxpwTDMPerf1DayIntervalNumber
The number of interval, where 1 indicates current day
measured period and 2 and above indicate previous days
respectively
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.1
jnxpwTDMPerf1DayIntervalValidData
This variable indicates if the data for this interval
is valid.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.2
jnxpwTDMPerf1DayIntervalDuration
The duration of a particular interval in seconds,
Adjustments in the system's time-of-day clock, may
cause the interval to be greater or less than, the
normal value. Therefore this actual interval value
is provided.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.3
jnxpwTDMPerf1DayIntervalMissingPkts
Number of missing packets (as detected via control word
sequence number gaps).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.4
jnxpwTDMPerf1DayIntervalPktsReOrder
Number of packets detected out of sequence (via control
word sequence number), but successfully re-ordered.
Note: some implementations may not support this
feature.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.5
jnxpwTDMPerf1DayIntervalJtrBfrUnderruns
Number of times a packet needed to be played
out and the jitter buffer was empty.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.6
jnxpwTDMPerf1DayIntervalMisOrderDropped
Number of packets detected out of order(via control word
sequence numbers), and could not be re-ordered, or could
not fit in the jitter buffer.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.7
jnxpwTDMPerf1DayIntervalMalformedPkt
Number of packets detected with unexpected size, or
bad headers' stack.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.8
jnxpwTDMPerf1DayIntervalESs
The counter associated with the number of Error
Seconds encountered.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.9
jnxpwTDMPerf1DayIntervalSESs
The counter associated with the number of Severely
Error Seconds.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.10
jnxpwTDMPerf1DayIntervalUASs
The counter associated with the number of
UnAvailable Seconds.

NOTE: When first entering the UAS state, the number
of SES To UAS is added to this object, then as each
additional UAS occurs, this object in…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.11
jnxpwTDMPerf1DayIntervalFC
TDM Failure Counts (FC-TDM). The number of TDM failure
events. A failure event begins when the LOPS failure
is declared, and ends when the failure is cleared.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2636.3.54.1.1.7.1.12