jnxpwTDMCfgExcessivePktLossThreshold

JUNIPER-PW-TDM-MIB · .1.3.6.1.4.1.2636.3.54.1.1.3.1.14

Object

column Percent SNMPv2-SMIUnsigned32

Excessive packet loss rate is detected by computing the
average packetloss rate over a pwTDMCfgAvePktLossTimeWindow
amount of time and comparing it with this threshold value.
The rate is expressed in precentage.
Object  MAY be changed when the related PW is
defined as not active.

Context

MIB: JUNIPER-PW-TDM-MIB
OID: .1.3.6.1.4.1.2636.3.54.1.1.3.1.14
Type: column
Access: readonly
Status: current
Units: Percent
Parent: jnxpwTDMCfgEntry
Table: jnxpwTDMCfgTable
Siblings: 19

Syntax

Percent SNMPv2-SMIUnsigned32

Source: SNMPv2-SMIUnsigned32
Base type: Unsigned32

Values & Constraints

Type Constraints

range: 0..4294967295

Related Objects

Sibling Objects

Object	Type	Syntax	OID
jnxpwTDMCfgIndex Index to an entry in this table. The value is a copy of the assigned pwTDMCfgIndexNext	column	JnxPwTDMCfgIndex	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.1`
jnxpwTDMCfgConsecMissPktsOutSynch The number of consecutive missing packets that are required to enter the LOPS state. Object MAY be changed when the related PW is defined as not active.	column	SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.10`
jnxpwTDMCfgSetUp2SynchTimeOut The amount of time the host should wait before declaring the pseudo wire in down state, if the number of consecutive TDM packets that have been received after changing the admins…	column	millisecond SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.11`
jnxpwTDMCfgPktReplacePolicy This parameter determines the value to be played when CE bound packets have over/underflow the jitter buffer, or are missing for any reason. This byte pattern is sent(played)on th…	column	Enumeration	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.12`
jnxpwTDMCfgAvePktLossTimeWindow The length of time over which the average packet loss rate should be computed to detect Excessive packet loss rate. Object MAY be changed when the related PW is defined as not ac…	column	millisecond SNMPv2-SMIInteger32	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.13`
jnxpwTDMCfgAlarmThreshold Alarms are only reported when the defect state persists for the length of time specified by this object. The object's unit is millisec. Object MAY be changed when the related PW …	column	SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.15`
jnxpwTDMCfgClearAlarmThreshold Alarm MUST be cleared after the corresponding defect is undetected for the amount of time specified by this object. The object's unit is millisec. Object MAY be changed when the …	column	SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.16`
jnxpwTDMCfgMissingPktsToSes Percent of missing packets detected (consecutive or not) within a 1 second window to cause a Severely Error Second (SES) to be counted. Object MAY be changed when the related PW …	column	Percent SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.17`
jnxpwTDMCfgTimestampMode Timestamp generation MAY be used in one of the following modes: 1. Absolute mode: the PSN-bound IWF sets timestamps using the clock recovered from the incoming TDM attachment ci…	column	Enumeration	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.18`
jnxpwTDMCfgStorageType This variable indicates the storage type for this row.	column	SNMPv2-TCStorageType	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.19`
jnxpwTDMCfgRowStatus Object used for creating, modifying, and deleting a row from this table. The following objects should not be modified if the entry is in used and the status is active: pwTDMCfgPay…	column	SNMPv2-TCRowStatus	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.2`
jnxpwTDMCfgPktFiller Filler byte pattern played out on the TDM interface if pwTDMCfgPktReplacePolicy was set to filler(3). Object MAY be changed when the related PW is defined as not active.	column	Unsigned32	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.20`
jnxpwTDMCfgName A descriptive string, prefereably unique name, to an entry in this table. Object MAY be changed at any time.	column	SNMP-FRAMEWORK-MIBSnmpAdminString	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.21`
jnxpwTDMCfgPayloadSize The value of this object indicates the PayLoad Size (in bytes) to be defined during the PW setUp. Upon TX, implementation must be capable of carrying that amount of bytes. Upon RX…	column	SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.4`
jnxpwTDMCfgPktReorder If set True: as CE bound packets are queued in the jitter buffer, out of order packets are re-ordered. The maximum sequence number differential (i.e., the range in which re-sequen…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.5`
jnxpwTDMCfgRtpHdrUsed If set to False: an RTP header is not pre-pended to the TDM packet.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.6`
jnxpwTDMCfgJtrBfrDepth The size of this buffer SHOULD be locally configured to allow accommodation to the PSN-specific packet delay variation. If configured to a value not supported by th…	column	microsecond SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.7`
jnxpwTDMCfgPayloadSuppression Selecting 'enable' means: Payload suppression is allowed. Payload MAY be omitted in order to conserve bandwidth. Selecting 'disable' means: no suppresion under any condition. Obje…	column	Enumeration	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.8`
jnxpwTDMCfgConsecPktsInSynch The number of consecutive packets with sequential sequence numbers that are required to exit the LOPS state. Object MAY be changed when the related PW is defined as not active.	column	SNMPv2-SMIUnsigned32	`.1.3.6.1.4.1.2636.3.54.1.1.3.1.9`