HP-ICF-RATE-LIMIT-MIB Table View

A table that contains configuration objects on ICMP 
rate limit on a per interface basis.

hpICMPRateLimitPortConfigEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1

Entry that contains configuration objects on ICMP
rate limit on a per interface basis

Indexes

hpICMPRateLimitPortConfigIndex

Column	Syntax	OID
hpICMPRateLimitPortConfigIndex The interface index associated with this entry.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.1
hpICMPRateLimitPortStatedeprecated This object indicates whether ICMP rate limiting is enabled on the corresponding port. Because this is a State object it cannot distinguish between percent-based ICMP Rate-Limiting and the newer Kbps-base…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.2
hpICMPRateLimitPortPrct This indicates the percent of ICMP rate limit on the port. The value of this object must be interpreted under the context of hpICMPRateLimitPortState. A value of 0 is not the same as disabling, but rather all ICMP …	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.3
hpICMPRateLimitPortAlarmFlag This object indicates whether ICMP rate limiting alarm has been sent. When an alarm is sent, this object is set to set(2). Once a management station changes this object to clear(1), an alarm can be sent again for thi…	Enumerationr/w Enumerated Values: 1 clear 2 set	.1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.4
hpICMPRateLimitPortKbps The maximum Kilobits-per-second of ICMP traffic that may be received inbound on the port. The value of this object must be interpreted under the context of hpICMPRateLimitControlMode. A value of 0 is not the same a…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.5
hpICMPRateLimitPortControlMode The mode by which inbound ICMP traffic on this port will Rate-Limited. If icmpRateLimitPerPortOnly is configured, there will be a single maximum percentage-based rate for the entire port. If icmpRateLimitPerPortOnly…	Enumerationr/w Enumerated Values: 1 disabled 2 portPrct 3 portKbps	.1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.6
hpICMPRateLimitPortIpPacketType This object represents the type(s) of IP packet to which the specified ICMP rate-limit will be applied. The default is IPv4.	Enumerationr/w Enumerated Values: 1 ipv4PacketsOnly 2 ipv6PacketsOnly 3 ipv4AndIpv6Packets	.1.3.6.1.4.1.11.2.14.10.2.14.1.1.1.1.1.7

A table that contains information about the port's egress
Guaranteed Minimum Bandwidth percent configurations on
this switch.  The number of entries in this table is 
determined by hpBWMinEgressPortNumQueues.  The priority of 
the queues is in ascending order, starting with queue one 
being the lowest and queue hpBWMinEgressPortNumQueues 
being the highest.

hpBWMinEgressPortPrctEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2.1

The information associated with each port's egress
Guaranteed Minimum Bandwidth percent configuration.

Indexes

IF-MIBifIndex hpBWMinEgressPortPrctQueue

Column	Syntax	OID
hpBWMinEgressPortPrctQueue The queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpBWMinEgressPortNumQueues being the highest.	Integer32 Constraints: range: 1-9000	.1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2.1.1
hpBWMinEgressPortPrct The percentage of Guaranteed Minimum bandwidth to be assigned to this egress queue for this port. Total values for all queues must not exceed 100 percent.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.11.2.14.10.2.14.1.2.1.2.1.2

A table that contains information about the port's
ingress Guaranteed Minimum Bandwidth percent 
configurations on this switch.  The number of entries in 
this table is determined by hpBWMinIngressPortNumQueues.  
The priority of the queues is in ascending order, starting 
with queue one being the lowest and queue 
hpBWMinIngressPortNumQueues being the highest.

hpBWMinIngressPortPrctEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2.1

The information associated with each port's ingress
Guaranteed Minimum Bandwidth percent configuration.

Indexes

IF-MIBifIndex hpBWMinIngressPortPrctQueue

Column	Syntax	OID
hpBWMinIngressPortPrctQueue The queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpBWMinIngressPortNumQueues being the highest.	Integer32 Constraints: range: 1-9000	.1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2.1.1
hpBWMinIngressPortPrct The percentage of Guaranteed Minimum bandwidth to be assigned to this ingress queue for this port. Total values for all queues must not exceed 100 percent.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.11.2.14.10.2.14.1.3.1.2.1.2

A table that contains information about the port egress 
Rate-Limiting configurations on this switch.

hpEgressRateLimitPortConfigEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1

The information associated with each port's egress
Rate-Limiting configuration.

Indexes

hpEgressRateLimitPortIndex

Column	Syntax	OID
hpEgressRateLimitPortIndex The ifIndex value which uniquely identifies a row in the Interfaces Table.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.1
hpEgressRateLimitPortControlMode The mode by which this port will be Rate-Limited on egress. If egressRateLimitPerPortOnly is configured, there will be a single maximum percentage-based rate for the entire port. If egressRateLimitPerQueue is configur…	Enumerationr/w Enumerated Values: 1 disabled 2 egressRateLimitPerPortOnly 3 egressRateLimitPerQueue 4 egressRateLimitPerPortOnlyBpsMode 5 egressRateLimitPerQueueBpsMode 6 egressRateLimitPerPortOnlyKbpsMode	.1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.2
hpEgressRateLimitPortSingleControlPrct When hpEgressRateLimitPortControlMode is configured for egressRateLimitPerPortOnly, this value is the maximum percentage of traffic that may be transmitted by this port on egress.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.3
hpEgressRateLimitPortSingleControlBpsdeprecated When hpEgressRateLimitPortControlMode is configured for egressRateLimitPerPortOnlyBpsMode, this value is the maximum bits-per-second of traffic that may be transmitted by this port on egress.	Unsigned32r/w Constraints: range: 0-4200000000	.1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.4
hpEgressRateLimitPortSingleControlKbps When hpEgressRateLimitPortControlMode is configured for egressRateLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of traffic that may be transmitted by this port on egress.	Integer32r/w Constraints: range: 0-100000000	.1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.5
hpEgressRateLimitPortQueueControlMode The mode by which queues on this port will be rate-limited on egress. If egressRateLimitQueuePrctMode is configured, the values for each of the queues indicate the maximum percentage of port traffic that may be transmit…	Enumerationr/w Enumerated Values: 1 disabled 2 egressRateLimitQueuePrctMode 3 egressRateLimitQueueKbpsMode	.1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.2.1.6

A table that contains information about the port egress 
Rate-Limiting percent configurations on this switch. The 
number of entries in this table is determined by 
hpEgressRateLimitPortNumQueues.  The priority of the 
queues is in ascending order, starting with queue one 
being the lowest priority and queue 
hpEgressRateLimitPortNumQueues being the highest 
priority.

hpEgressRateLimitPortPrctEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3.1

The information associated with each port's egress
Rate-Limiting percent configuration.

Indexes

hpEgressRateLimitPortIndex hpEgressRateLimitPortPrctQueue

Column	Syntax	OID
hpEgressRateLimitPortPrctQueue The queue associated with this entry. The priority o of the queues is in ascending order, starting with queue one being the lowest and queue hpEgressRateLimitgressPortNumQueues being the highest.	Integer32 Constraints: range: 1-9000	.1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3.1.1
hpEgressRateLimitPortPrct The maximum percentage of traffic that may be transmitted by this port's queue on egress. hpEgressRateLimitPortControlMode must be configured to use egressRateLimitPerQueue for this to take effect. A value of 0-perce…	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.3.1.2

A table that contains information about the port egress-
queue rate-limiting configurations on this switch.

hpEgressRateLimitPortQueueConfigEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.5.1

The information associated with the egress
rate-limiting configuration for the queues on each port.

Indexes

hpEgressRateLimitPortIndex hpEgressRateLimitPortQueueIndex

Column	Syntax	OID
hpEgressRateLimitPortQueueIndex The queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpEgressRateLimitEgressPortNumQueues being the highest.	Integer32 Constraints: range: 1-9000	.1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.5.1.1
hpEgressRateLimitPortQueueMax The maximum amount of traffic that may be transmitted by this port's corresponding queue on egress. When the value of hpEgressRateLimitPortQueueControlMode is egressRateLimitQueuePrctMode, this maximum value is a percen…	Integer32r/w Constraints: range: 0-100000000	.1.3.6.1.4.1.11.2.14.10.2.14.1.4.1.5.1.2

A table that contains information about the port ingress 
Rate-Limiting configurations on this switch.

hpIngressRateLimitPortConfigEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1

The information associated with each port's ingress
Rate-Limiting configuration.

Indexes

hpIngressRateLimitPortIndex

Column	Syntax	OID
hpIngressRateLimitPortIndex The ifIndex value which uniquely identifies a row in the Interfaces Table.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.1
hpIngressRateLimitPortControlMode The mode by which this port will be Rate-Limited on ingress. If ingressRateLimitPerPortOnly is configured, there will be a single maximum percentage-based rate for the entire port. If ingressRateLimitPerQueue is conf…	Enumerationr/w Enumerated Values: 1 disabled 2 ingressRateLimitPerPortOnly 3 ingressRateLimitPerQueue 4 ingressRateLimitPerPortOnlyBpsMode 5 ingressRateLimitPerQueueBpsMode 6 ingressRateLimitPerPortOnlyKbpsMode	.1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.2
hpIngressRateLimitPortSingleControlPrct When hpIngressRateLimitPortControlMode is configured for ingressRateLimitPerPortOnly, this value is the maximum percentage of traffic that may be transmitted by this port on egress.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.3
hpIngressRateLimitPortSingleControlBpsdeprecated When hpIngressRateLimitPortControlMode is configured for ingressRateLimitPerPortOnlyBpsMode, this value is the maximum bits-per-second of traffic that may be transmitted by this port on ingress.	Unsigned32r/w Constraints: range: 0-4200000000	.1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.4
hpIngressRateLimitPortSingleControlKbps When hpIngressRateLimitPortControlMode is configured for ingressRateLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of traffic that may be transmitted by this port on ingress.	Integer32r/w Constraints: range: 0-100000000	.1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.2.1.5

A table that contains information about the port ingress 
Rate-Limiting percent configurations on this switch.  The 
number of entries in this table is determined by 
hpIngressRateLimitPortNumQueues.  The priority of the 
queues is in ascending order, starting with queue one 
being the lowest priority and queue 
hpIngressRateLimitPortNumQueues being the highest 
priority.

hpIngressRateLimitPortPrctEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3.1

The information associated with each port's ingress
Rate-Limiting percent configuration.

Indexes

hpIngressRateLimitPortIndex hpIngressRateLimitPortPrctQueue

Column	Syntax	OID
hpIngressRateLimitPortPrctQueue The queue associated with this entry. The priority of the queues is in ascending order, starting with queue one being the lowest and queue hpIngressRateLimitgressPortNumQueues being the highest.	Integer32 Constraints: range: 1-9000	.1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3.1.1
hpIngressRateLimitPortPrct The maximum percentage of traffic that may be transmitted by this port's queue on ingress. hpIngressRateLimitPortControlMode must be configured to use ingressRateLimitPerQueue for this to take effect. A value of 0-pe…	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.11.2.14.10.2.14.1.5.1.3.1.2

A table that contains information about the port ingress 
Broadcast-Limiting configurations on this switch.

hpIngressBcastLimitPortConfigEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1

The information associated with each port's ingress
Broadcast-Limiting configuration.

Indexes

hpIngressBcastLimitPortIndex

Column	Syntax	OID
hpIngressBcastLimitPortIndex The ifIndex value which uniquely identifies a row in the Interfaces Table.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.1
hpIngressBcastLimitPortControlMode The mode by which this port will be Broadcast-Limited on ingress. If ingressBcastLimitPerPortOnly is configured, there will be a single maximum percentage-based broadcast traffic limit for the entire port. If ingressB…	Enumerationr/w Enumerated Values: 1 disabled 2 ingressBcastLimitPerPortOnly 3 ingressBcastLimitPerPortOnlyKbpsMode	.1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.2
hpIngressBcastLimitPortSingleControlPrct When hpIngressBcastLimitPortControlMode is configured for ingressBcastLimitPerPortOnly, this value is the maximum percentage of traffic that may be transmitted by this port on ingress.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.3
hpIngressBcastLimitPortSingleControlKbps When hpIngressBcastLimitPortControlMode is configured for ingressBcastLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of broadcast traffic that may be transmitted by this port on ingress.	Integer32r/w Constraints: range: 0-100000000	.1.3.6.1.4.1.11.2.14.10.2.14.1.6.1.1.1.4

A table that contains information about the port ingress 
Multicast-Limiting configurations on this switch.

hpIngressMcastLimitPortConfigEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1

The information associated with each port's ingress
Multicast-Limiting configuration.

Indexes

hpIngressMcastLimitPortIndex

Column	Syntax	OID
hpIngressMcastLimitPortIndex The ifIndex value which uniquely identifies a row in the Interfaces Table.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.1
hpIngressMcastLimitPortControlMode The mode by which this port will be Multicast-Limited on ingress. If ingressMcastLimitPerPortOnly is configured, there will be a single maximum percentage-based multicast traffic limit for the entire port. If ingressM…	Enumerationr/w Enumerated Values: 1 disabled 2 ingressMcastLimitPerPortOnly 3 ingressMcastLimitPerPortOnlyKbpsMode	.1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.2
hpIngressMcastLimitPortSingleControlPrct When hpIngressMcastLimitPortControlMode is configured for ingressMcastLimitPerPortOnly, this value is the maximum percentage of multicast traffic that may be transmitted by this port on ingress.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.3
hpIngressMcastLimitPortSingleControlKbps When hpIngressMcastLimitPortControlMode is configured for ingressMcastLimitPerPortOnlyKbpsMode, this value is the maximum kilobits-per-second of multicast traffic that may be transmitted by this port on ingress.	Integer32r/w Constraints: range: 0-100000000	.1.3.6.1.4.1.11.2.14.10.2.14.1.7.1.1.1.4

A table that contains information about the 
unknown-unicast rate limiting configurations 
on this switch.

hpUnknownUnicastLimitConfigEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1.1

The information associated with each port's
unknown-unicast rate limiting configuration.

Indexes

hpUnknownUnicastLimitPortIndex

Column	Syntax	OID
hpUnknownUnicastLimitPortIndex The ifIndex value which uniquely identifies a row in the interfaces table.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1.1.1
hpUnknownUnicastLimitPortControlMode The mode by which unknown-unicast ingress traffic on this port will be rate limited. If unknownUnicastLimitPerPortOnly is configured, the limit will be a percentage of the current line rate of the port. The percentage…	Enumerationr/w Enumerated Values: 1 disabled 2 unknownUnicastLimitPerPortOnly 3 unknownUnicastLimitPerPortOnlyKbpsMode	.1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1.1.2
hpUnknownUnicastLimitPortSingleControlPrct When hpUnknownUnicastLimitPortControlMode is unknownUnicastLimitPerPortOnly, this value is the maximum allowed ingress rate for unknown-unicast traffic on this port as a percentage of the current line rate.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1.1.3
hpUnknownUnicastLimitPortSingleControlKbps When hpUnknownUnicastLimitPortControlMode is UnknownUnicastLimitPerPortOnlyKbpsMode, this value is the maximum allowed ingress rate for unknown-unicast traffic on this port in kilobits-per-second.	Integer32r/w Constraints: range: 0-100000000	.1.3.6.1.4.1.11.2.14.10.2.14.1.8.1.1.1.4

A table of VLAN rate limits.

hpicfIngressRateLimitVlanConfigEntry row .1.3.6.1.4.1.11.2.14.10.2.14.1.9.1.1

A set of objects used to configure rate
limits on a VLANs.

Indexes

hpicfIngressRateLimitVlanIndex

Column	Syntax	OID
hpicfIngressRateLimitVlanIndex The VLAN ifIndex value that uniquely identifies a row in the Interfaces Table and corresponds to the VLAN on which the rate limit is being set.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.11.2.14.10.2.14.1.9.1.1.1
hpicfIngressRateLimitVlanControlMode The rate limit mode. A value of 1 indicates that there is no rate limit set. A value of 2 indicates that the rate limit on the VLAN will be set in Kilobits per second.	Enumerationr/w Enumerated Values: 1 disabled 2 ingressVlanKbps	.1.3.6.1.4.1.11.2.14.10.2.14.1.9.1.1.2
hpicfIngressRateLimitVlanKbps The maximum rate of inbound traffic permitted on the VLAN in kilobits per second. This limit is the total aggregate inbound traffic allowed across all ports in the VLAN. The value of this object only takes effect when…	Unsigned32r/w Constraints: range: 0-260000000	.1.3.6.1.4.1.11.2.14.10.2.14.1.9.1.1.3