FRAME-RELAY-DTE-MIB Table View

The Parameters for the Data Link Connection Management
Interface for the frame relay service on this
interface.

frDlcmiEntry row .1.3.6.1.2.1.10.32.1.1

The Parameters for a particular Data Link Connection
Management Interface.

Indexes

frDlcmiIfIndex

Column	Syntax	OID
frDlcmiIfIndex The ifIndex value of the corresponding ifEntry.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.2.1.10.32.1.1.1
frDlcmiState This variable states which Data Link Connection Management scheme is active (and by implication, what DLCI it uses) on the Frame Relay interface.	Enumerationr/w Enumerated Values: 1 noLmiConfigured 2 lmiRev1 3 ansiT1617D 4 ansiT1617B 5 itut933A 6 ansiT1617D1994	.1.3.6.1.2.1.10.32.1.1.2
frDlcmiAddress This variable states which address format is in use on the Frame Relay interface.	Enumerationr/w Enumerated Values: 1 q921 2 q922March90 3 q922November90 4 q922	.1.3.6.1.2.1.10.32.1.1.3
frDlcmiAddressLen This variable states the address length in octets. In the case of Q922 format, the length indicates the entire length of the address including the control portion.	Enumerationr/w Enumerated Values: 2 twoOctets 3 threeOctets 4 fourOctets	.1.3.6.1.2.1.10.32.1.1.4
frDlcmiPollingInterval This is the number of seconds between successive status enquiry messages.	secondsInteger32r/w Constraints: range: 5-30	.1.3.6.1.2.1.10.32.1.1.5
frDlcmiFullEnquiryInterval Number of status enquiry intervals that pass before issuance of a full status enquiry message.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.2.1.10.32.1.1.6
frDlcmiErrorThreshold This is the maximum number of unanswered Status Enquiries the equipment shall accept before declaring the interface down.	Integer32r/w Constraints: range: 1-10	.1.3.6.1.2.1.10.32.1.1.7
frDlcmiMonitoredEvents This is the number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvents' number of events the station receives 'ErrorThreshold' number of errors, the interface …	Integer32r/w Constraints: range: 1-10	.1.3.6.1.2.1.10.32.1.1.8
frDlcmiMaxSupportedVCs The maximum number of Virtual Circuits allowed for this interface. Usually dictated by the Frame Relay network. In response to a SET, if a value less than zero or higher than the agent's maximal capabili…	DLCIr/w Type Constraints: range: 0..8388607	.1.3.6.1.2.1.10.32.1.1.9
frDlcmiMulticast This indicates whether the Frame Relay interface is using a multicast service.	Enumerationr/w Enumerated Values: 1 nonBroadcast 2 broadcast	.1.3.6.1.2.1.10.32.1.1.10
frDlcmiStatus This indicates the status of the Frame Relay interface as determined by the performance of the dlcmi. If no dlcmi is running, the Frame Relay interface will stay in the running state indefinitely.	Enumeration Enumerated Values: 1 running 2 fault 3 initializing	.1.3.6.1.2.1.10.32.1.1.11
frDlcmiRowStatus SNMP Version 2 Row Status Variable. Writable objects in the table may be written in any RowStatus state.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.32.1.1.12

A table containing information about specific Data
Link Connections (DLC) or virtual circuits.

frCircuitEntry row .1.3.6.1.2.1.10.32.2.1

The information regarding a single Data Link
Connection. Discontinuities in the counters contained
in this table are indicated by the value in
frCircuitCreationTime.

Indexes

frCircuitIfIndex frCircuitDlci

Column	Syntax	OID
frCircuitIfIndex The ifIndex Value of the ifEntry this virtual circuit is layered onto.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.2.1.10.32.2.1.1
frCircuitDlci The Data Link Connection Identifier for this virtual circuit.	DLCI Type Constraints: range: 0..8388607	.1.3.6.1.2.1.10.32.2.1.2
frCircuitState Indicates whether the particular virtual circuit is operational. In the absence of a Data Link Connection Management Interface, virtual circuit entries (rows) may be created by setting virtual circuit state to 'active'…	Enumerationr/w Enumerated Values: 1 invalid 2 active 3 inactive	.1.3.6.1.2.1.10.32.2.1.3
frCircuitReceivedFECNs Number of frames received from the network indicating forward congestion since the virtual circuit was created. This occurs when the remote DTE sets the FECN flag, or when a switch in the network enqueues the frame to …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.32.2.1.4
frCircuitReceivedBECNs Number of frames received from the network indicating backward congestion since the virtual circuit was created. This occurs when the remote DTE sets the BECN flag, or when a switch in the network receives the frame fr…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.32.2.1.5
frCircuitSentFrames The number of frames sent from this virtual circuit since it was created.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.32.2.1.6
frCircuitSentOctets The number of octets sent from this virtual circuit since it was created. Octets counted are the full frame relay header and the payload, but do not include the flag characters or CRC.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.32.2.1.7
frCircuitReceivedFrames Number of frames received over this virtual circuit since it was created.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.32.2.1.8
frCircuitReceivedOctets Number of octets received over this virtual circuit since it was created. Octets counted include the full frame relay header, but do not include the flag characters or the CRC.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.32.2.1.9
frCircuitCreationTime The value of sysUpTime when the virtual circuit was created, whether by the Data Link Connection Management Interface or by a SetRequest.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.2.1.10.32.2.1.10
frCircuitLastTimeChange The value of sysUpTime when last there was a change in the virtual circuit state	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.2.1.10.32.2.1.11
frCircuitCommittedBurst This variable indicates the maximum amount of data, in bits, that the network agrees to transfer under normal conditions, during the measurement interval.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.2.1.10.32.2.1.12
frCircuitExcessBurst This variable indicates the maximum amount of uncommitted data bits that the network will attempt to deliver over the measurement interval. By default, if not configured when creating the entry, the Exces…	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.2.1.10.32.2.1.13
frCircuitThroughput Throughput is the average number of 'Frame Relay Information Field' bits transferred per second across a user network interface in one direction, measured over the measurement interval. If the configured …	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.2.1.10.32.2.1.14
frCircuitMulticast This indicates whether this VC is used as a unicast VC (i.e. not multicast) or the type of multicast service subscribed to	Enumerationr/w Enumerated Values: 1 unicast 2 oneWay 3 twoWay 4 nWay	.1.3.6.1.2.1.10.32.2.1.15
frCircuitType Indication of whether the VC was manually created (static), or dynamically created (dynamic) via the data link control management interface.	Enumeration Enumerated Values: 1 static 2 dynamic	.1.3.6.1.2.1.10.32.2.1.16
frCircuitDiscards The number of inbound frames dropped because of format errors, or because the VC is inactive.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.32.2.1.17
frCircuitReceivedDEs Number of frames received from the network indicating that they were eligible for discard since the virtual circuit was created. This occurs when the remote DTE sets the DE flag, or when in remote DTE's switch detects …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.32.2.1.18
frCircuitSentDEs Number of frames sent to the network indicating that they were eligible for discard since the virtual circuit was created. This occurs when the local DTE sets the DE flag, indicating that during Network congestion sit…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.32.2.1.19
frCircuitLogicalIfIndex Normally the same value as frDlcmiIfIndex, but different when an implementation associates a virtual ifEntry with a DLC or set of DLCs in order to associate higher layer objects such as the ipAddrEntry with a subset of …	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.2.1.10.32.2.1.20
frCircuitRowStatus This object is used to create a new row or modify or destroy an existing row in the manner described in the definition of the RowStatus textual convention. Writable objects in the table may be written in any RowStatus s…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.32.2.1.21

A table containing information about Errors on the
Frame Relay interface.  Discontinuities in the counters
contained in this table are the same as apply to the
          
ifEntry associated with the Interface.

frErrEntry row .1.3.6.1.2.1.10.32.3.1

The error information for a single frame relay
interface.

Indexes

frErrIfIndex

Column	Syntax	OID
frErrIfIndex The ifIndex Value of the corresponding ifEntry.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.2.1.10.32.3.1.1
frErrType The type of error that was last seen on this interface: receiveShort: frame was not long enough to allow demultiplexing - the address field was incomplete, or for virtual circuits using Multiprotocol ov…	Enumeration Enumerated Values: 1 unknownError 2 receiveShort 3 receiveLong 4 illegalAddress 5 unknownAddress 6 dlcmiProtoErr 7 dlcmiUnknownIE 8 dlcmiSequenceErr 9 dlcmiUnknownRpt 10 noErrorSinceReset	.1.3.6.1.2.1.10.32.3.1.2
frErrData An octet string containing as much of the error packet as possible. As a minimum, it must contain the Q.922 Address or as much as was delivered. It is desirable to include all header and demultiplexing information.	OctetString Constraints: range: 1-1600	.1.3.6.1.2.1.10.32.3.1.3
frErrTime The value of sysUpTime at which the error was detected.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.2.1.10.32.3.1.4
frErrFaults The number of times the interface has gone down since it was initialized.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.32.3.1.5
frErrFaultTime The value of sysUpTime at the time when the interface was taken down due to excessive errors. Excessive errors is defined as the time when a DLCMI exceeds the frDlcmiErrorThreshold number of errors within frDlcmiMonito…	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.2.1.10.32.3.1.6