DCP-OPS-MIB Table View

This table contains entries representing individual
Optical Protection Switch instances within the DCP
platform.
          
Each entry corresponds to one protection switch,
providing configuration, operational status, optical
power measurements, switching mode, and alarm
information.
          
The number of entries depends on the installed
hardware configuration.

dcpOpsSwitchEntry row .1.3.6.1.4.1.30826.2.2.8.1.1.1

An entry representing a single Optical Protection
Switch instance within the DCP platform.

Each entry models one independent protection switch
with a client interface and two line interfaces
(Line A and Lin…

Indexes

dcpOpsSwitchIndex

Column	Syntax	OID
dcpOpsSwitchIndex A unique index identifying an Optical Protection Switch instance within the DCP system. The index is encoded using the following format: c s oo 00 where: …	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.30826.2.2.8.1.1.1.1
dcpOpsSwitchName A textual description of the Optical Protection Switch instance. This string is intended for identification and may reflect installation or operational information.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.30826.2.2.8.1.1.1.2
dcpOpsSwitchAdminStatus The administrative status of the protection switch. up(1) - The protection switch is administratively enabled and allowed to operate. down(2) - The protection switch is administra…	SO-TC-MIBAdminStatus Type Values: 1 up 2 down 3 testing 4 service Description: The adminStatus for a port, interface, or optical channel. up - The port, interface or optical channel is configured to be in-service. down - The port, interface or optical channel is NOT configured to be in-service. te…	.1.3.6.1.4.1.30826.2.2.8.1.1.1.3
dcpOpsSwitchClientRxPower The received optical power at the client interface, expressed in units of 0.1 dBm.	SO-TC-MIBOpticalPower1Decimal Description: Power level at an interface in units of 0.1 dBm.	.1.3.6.1.4.1.30826.2.2.8.1.1.1.4
dcpOpsSwitchClientTxPower The transmitted optical power at the client interface, expressed in units of 0.1 dBm.	SO-TC-MIBOpticalPower1Decimal Description: Power level at an interface in units of 0.1 dBm.	.1.3.6.1.4.1.30826.2.2.8.1.1.1.5
dcpOpsSwitchLineARxPower The received optical power at the Line A interface, expressed in units of 0.1 dBm.	SO-TC-MIBOpticalPower1Decimal Description: Power level at an interface in units of 0.1 dBm.	.1.3.6.1.4.1.30826.2.2.8.1.1.1.6
dcpOpsSwitchLineATxPower The transmitted optical power at the Line A interface, expressed in units of 0.1 dBm.	SO-TC-MIBOpticalPower1Decimal Description: Power level at an interface in units of 0.1 dBm.	.1.3.6.1.4.1.30826.2.2.8.1.1.1.7
dcpOpsSwitchLineBRxPower The received optical power at the Line B interface, expressed in units of 0.1 dBm.	SO-TC-MIBOpticalPower1Decimal Description: Power level at an interface in units of 0.1 dBm.	.1.3.6.1.4.1.30826.2.2.8.1.1.1.8
dcpOpsSwitchLineBTxPower The transmitted optical power at the Line B interface, expressed in units of 0.1 dBm.	SO-TC-MIBOpticalPower1Decimal Description: Power level at an interface in units of 0.1 dBm.	.1.3.6.1.4.1.30826.2.2.8.1.1.1.9
dcpOpsSwitchClientLosThreshold The configured Loss of Signal (LOS) threshold for the client interface, expressed in units of 0.1 dBm. An LOS condition is declared when the received optical power falls below this threshold.	SO-TC-MIBOpticalPower1Decimal Description: Power level at an interface in units of 0.1 dBm.	.1.3.6.1.4.1.30826.2.2.8.1.1.1.10
dcpOpsSwitchLineALosThreshold The configured Loss of Signal (LOS) threshold for the Line A interface, expressed in units of 0.1 dBm. An LOS condition is declared when the received optical power falls below this threshold.	SO-TC-MIBOpticalPower1Decimal Description: Power level at an interface in units of 0.1 dBm.	.1.3.6.1.4.1.30826.2.2.8.1.1.1.11
dcpOpsSwitchLineBLosThreshold The configured Loss of Signal (LOS) threshold for the Line B interface, expressed in units of 0.1 dBm. An LOS condition is declared when the received optical power falls below this threshold.	SO-TC-MIBOpticalPower1Decimal Description: Power level at an interface in units of 0.1 dBm.	.1.3.6.1.4.1.30826.2.2.8.1.1.1.12
dcpOpsSwitchActiveLine Indicates which line interface (Line A or Line B) is currently selected to carry traffic.	DcpOpsActiveLine Type Values: 1 lineA 2 lineB Description: Indicates which line interface is currently selected on the receive side to carry client traffic within the protection switch. Transmission towards both Line A and Line B may occur simultaneously, depending o…	.1.3.6.1.4.1.30826.2.2.8.1.1.1.13
dcpOpsSwitchMode The configured protection switching mode of this Optical Protection Switch instance.	DcpOpsMode Type Values: 1 auto 2 revertiveA 3 revertiveB 4 forcedA 5 forcedB Description: Indicates the configured protection switching mode of the Optical Protection Switch. auto(1) - Non-revertive mode. Traffic is carried on the line that becomes active first when the system starts. …	.1.3.6.1.4.1.30826.2.2.8.1.1.1.14
dcpOpsSwitchAlarmSeverity Indicates the highest perceived severity of all currently active alarms associated with this Optical Protection Switch instance. The value reflects the most severe active alarm, according to ITU-T perceiv…	SO-TC-MIBItuPerceivedSeverity Type Values: 1 cleared 2 indeterminate 3 critical 4 major 5 minor 6 warning Description: ITU perceived severity values	.1.3.6.1.4.1.30826.2.2.8.1.1.1.15
dcpOpsSwitchDescription User configurable description string for the optical switch.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.30826.2.2.8.1.1.1.16