CISCO-WIRELESS-P2MP-PHY-MIB Table View

This table provides facilities to configure the physical
layer characteristics of the radio link.
The objects in this table are supported on the head end and 
at the subscriber unit.

p2mpRadioPhyEntry row .1.3.6.1.4.1.9.9.170.1.1.1.1.1

The entry of this table is created when the managed system
detects a propDocsWirelessMaclayer interface. The entry
is removed when the associated propDocsWirelessMaclayer
interface is deleted from the ifTable.

Indexes

IF-MIBifIndex

Column	Syntax	OID
p2mpSelfTest This object is used to enable/disable self test. When set to true(1), the software tests the memory and hardware integrity shortly after the router powers up.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.170.1.1.1.1.1.1
p2mpDiversityAntennaPresent When true(1), this object indicates that a diversity antenna is being used to receive the wireless transmissions. When false(2), the radio system is using a single antenna to transmit and receive.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.170.1.1.1.1.1.2
p2mpCableLoss This object indicates the measured signal power loss in dB due to the cable connecting the radio to the main antenna. The hardware compensates for this cable loss by adjusting the receive and transmit gain appropriately…	dBUnsigned32r/w Constraints: range: 0-15	.1.3.6.1.4.1.9.9.170.1.1.1.1.1.3
p2mpCableLossDiversity This object indicates the measured signal power loss in dB due to the cable connecting the radio to the diversity antenna. The hardware compensates for this loss by adjusting the receive and transmit gain appropriat…	dBUnsigned32r/w Constraints: range: 0-15	.1.3.6.1.4.1.9.9.170.1.1.1.1.1.4
p2mpDenyService Indicates if the service is disabled in the unit. For Head-end unit, if this object has the value of 'true', the link is in loopback mode; otherwise the link is enabled for transmitting / receiving data. For Subscribe…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.170.1.1.1.1.1.5
p2mpClockRefExt This object controls the use of external reference clock for IF module as follows: 'true(1)' - an external reference clock is used 'false(2)' - an internal reference clock is used.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.170.1.1.1.1.1.6
p2mpCommonTrapEnable When set to true(1), the notifications common to the head end and subscriber unit are enabled. When set to false(2), these notifications are disabled. The notification controlled by this object are: - p2mpRadioPhy…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.170.1.1.1.1.1.7
p2mpLastPhyFailureType This object indicates the last physical link failure that resulted in a p2mpRadioPhyFailNotification trap. none(1) - no failure p2mpHwConfigUnsupported(2) - The radio subsystem has…	Enumeration Enumerated Values: 1 none 2 p2mpHwConfigUnsupported 3 p2mpHwConfigMismatch 4 p2mpHwInitFailure 5 p2mpHostIfCommLinkError 6 p2mpAutoCableCompFailure	.1.3.6.1.4.1.9.9.170.1.1.1.1.1.8
p2mpLastPhyFailureReason This is a text string that describes the last physical link failure identified by p2mpLastPhyFailureType.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.9.9.170.1.1.1.1.1.9

This table contains information about the state of the radio 
frequency resources used by the radio system.
          
Physically each RF resource may be realized by one antenna and 
its associated control hardware. A single antenna and its 
associated electronics may act as more than 1 RF resource. When
an RF resource acts as both a transmit and receive resource,
the transmit and receive frequency ranges may overlap.

p2mpRfEntry row .1.3.6.1.4.1.9.9.170.1.1.2.1.1

This represents one entry in the p2mpRfTable.

An entry is created in this table when the managed system
detects a RF resource. The entry is removed when the RF
resource is removed from the wireless syst…

Indexes

IF-MIBifIndex p2mpRfIndex

Column	Syntax	OID
p2mpRfIndex This object, along with the ifIndex of the MAC layer, represents the index of this entry in the p2mpRfTable. Each entry in the table provides details on the state of the RF resources available in the system.	Integer32 Constraints: range: 1-100	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.1
p2mpRfType This object identifies the RF resource.	CISCO-WIRELESS-TC-MIBCwrRfType Type Values: 0 main 1 diversity	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.2
p2mpRfOpMode This object specifies whether this RF resource can either transmit, receive, or do both.	Enumeration Enumerated Values: 1 receiveOnly 2 transmitOnly 3 transmitAndReceive	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.3
p2mpTxFreqRangeMin This object represents the minimum frequency at which this RF resource can transmit.	KHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange Type Constraints: range: 0..60000000	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.4
p2mpTxFreqRangeMax This object represents the maximum frequency at which this RF resource can transmit.	KHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange Type Constraints: range: 0..60000000	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.5
p2mpRxFreqRangeMin This object represents the lowest transmission frequency this RF resource can receive.	KHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange Type Constraints: range: 0..60000000	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.6
p2mpRxFreqRangeMax This object represents the highest transmission frequency that this RF resource can receive.	KHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange Type Constraints: range: 0..60000000	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.7
p2mpMinTxPower This object represents the minimum power that the RF subsystem can supply the antenna.	dBmInteger32 Constraints: range: -80-50	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.8
p2mpMaxTxPower This object represents the maximum power that the RF subsystem can supply the antenna.	dBmInteger32 Constraints: range: -80-50	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.9
p2mpRfTemperature This object represents the current temperature of the RF unit	Degrees CentigradeInteger32 Constraints: range: -40-100	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.10
p2mpRfTxOscState This object represents the state of the transmit oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.	CISCO-WIRELESS-TC-MIBCwrOscState Type Values: 1 oscillatorOk 2 osccillatorBad	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.11
p2mpRfRxOscState This object represents the state of the receive oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.	CISCO-WIRELESS-TC-MIBCwrOscState Type Values: 1 oscillatorOk 2 osccillatorBad	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.12
p2mpRfSupplyVoltageState This object specifies whether the voltage supply to the RF unit is within specifications or not. Voltage specifications are hardware dependent.	Enumeration Enumerated Values: 1 withinSpecification 2 outsideSpecification	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.13
p2mpRfStatus This object specifies whether the RF resource is functioning properly. If it is functioning properly then it will be online(1), else offline(2). At the Subscriber Unit, this object will reflect offline(2) if p2mpTxMu…	Enumeration Enumerated Values: 1 online 2 offline	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.14
p2mpRfLoopbackSupported This object indicates if the RF unit supports loopback. When true(1), the user can configure loopback using the objects in p2mpLoopbackTable. When false(2), any attempt to configure RF loopback will fail.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.170.1.1.2.1.1.15

This table contains information about the Duplexers
available for use on the system.
          
A Duplexer is a mechanical device, that acts as a band 
pass filter when installed in an RF resource.
          
Normally a RF resource is capable of operating over a wide
frequency range. To operate at restricted frequencies, the user
has to own that part of the frequency spectrum.  Since the user
may not own parts of the frequency spectrum over which the RF
resource may operate, a duplexer is installed at the RF.
This restricts the RF resource to operate in the passband
defined by the duplexer.

p2mpDuplexerEntry row .1.3.6.1.4.1.9.9.170.1.1.2.2.1

This represents one entry in the p2mpDuplexerTable.
Each entry contains information about the duplexers
capabilities and the associated RF resource.

An entry is created in this table when the managed syst…

Indexes

IF-MIBifIndex p2mpDuplexerIndex

Column	Syntax	OID
p2mpDuplexerIndex This object, along with ifIndex, uniquely identifies an entry in this table. Each entry contains information about the duplexer's capabilities and also identifies the associated RF resource.	Integer32 Constraints: range: 1-100	.1.3.6.1.4.1.9.9.170.1.1.2.2.1.1
p2mpDuplexerRF This object identifies the RF resource associated with this duplexer.	CISCO-WIRELESS-TC-MIBCwrRfType Type Values: 0 main 1 diversity	.1.3.6.1.4.1.9.9.170.1.1.2.2.1.2
p2mpDuplexerLoPassbandMinFreq This object identifies the minimum frequency in the low passband that this duplexer will pass through without attenuation.	MHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange Type Constraints: range: 0..60000000	.1.3.6.1.4.1.9.9.170.1.1.2.2.1.3
p2mpDuplexerLoPassbandMaxFreq This object identifies the maximum frequency in the low passband that this duplexer will pass through without attenuation.	MHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange Type Constraints: range: 0..60000000	.1.3.6.1.4.1.9.9.170.1.1.2.2.1.4
p2mpDuplexerHiPassbandMinFreq This object identifies the minimum frequency in the high passband that this duplexer will pass through without attenuation.	MHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange Type Constraints: range: 0..60000000	.1.3.6.1.4.1.9.9.170.1.1.2.2.1.5
p2mpDuplexerHiPassbandMaxFreq This object identifies the maximum frequency in the high passband that this duplexer will pass through without attenuation.	MHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange Type Constraints: range: 0..60000000	.1.3.6.1.4.1.9.9.170.1.1.2.2.1.6
p2mpDuplexerReceivePassband This object indicates which of the two passbands are being used to receive transmissions. The RF Resource can receive on either of the duplexer passbands. loPassband(1) - The RF Resource is receiving on …	Enumeration Enumerated Values: 1 loPassband 2 hiPassband	.1.3.6.1.4.1.9.9.170.1.1.2.2.1.7
p2mpDuplexerTxInsertionLoss This object represents the loss in 'dB' that would result in the transmission path due to the duplexer.	dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.9.170.1.1.2.2.1.8
p2mpDuplexerBurnDate This object indicates the date when the revision information was programmed into non-volatile memory.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.9.9.170.1.1.2.2.1.9

This table contains information about the antennas available 
in the system.

p2mpAntennaEntry row .1.3.6.1.4.1.9.9.170.1.1.2.3.1

An entry is created in this table when the managed system
detects a RF resource. The entry is removed when the RF
resource is removed from the wireless system.

Indexes

IF-MIBifIndex p2mpAntennaIndex

Column	Syntax	OID
p2mpAntennaIndex This object, along with ifIndex, represents the index of this entry in the p2mpAntennaTable.	CISCO-TCUnsigned32	.1.3.6.1.4.1.9.9.170.1.1.2.3.1.1
p2mpRfResource This object identifies if the antenna is connected to the main or the diversity RF resource.	CISCO-WIRELESS-TC-MIBCwrRfType Type Values: 0 main 1 diversity	.1.3.6.1.4.1.9.9.170.1.1.2.3.1.2
p2mpAntennaXDim This object represents the dimension of the antenna in the X direction.	InchesUnsigned32r/w Constraints: range: 1-96	.1.3.6.1.4.1.9.9.170.1.1.2.3.1.3
p2mpAntennaYDim This object represents the dimension of the antenna in the Y direction.	InchesUnsigned32r/w Constraints: range: 1-96	.1.3.6.1.4.1.9.9.170.1.1.2.3.1.4
p2mpAntennaType This object represents the antenna type. For example, 'dish-antenna'.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.9.9.170.1.1.2.3.1.5
p2mpAntennaDescr This object is used to describe the antenna. For example, it could be used to identify the manufacturer like in 'Manufactured by Watkins Johnson'.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.9.9.170.1.1.2.3.1.6
p2mpAntennaGain This object represents the receive and transmit gain of this antenna.	dBi : decibel IsotropicUnsigned32r/w Constraints: range: 0-60	.1.3.6.1.4.1.9.9.170.1.1.2.3.1.7
p2mpAntennaPolarization This object represents the polarization of the antanna.	Enumeration Enumerated Values: 1 vertical 2 horizontal	.1.3.6.1.4.1.9.9.170.1.1.2.3.1.8

This table provides facilities to establish loopback points to
exercise various sections of the hardware.

p2mpLoopbackEntry row .1.3.6.1.4.1.9.9.170.1.1.3.1.1

This represents one entry in the p2mpLoopbackTable. It
is created when the managed system detects a
propDocsWirelessMaclayer interface. The entry is removed
when the associated propDocsWirelessMaclayer interface
is d…

Indexes

IF-MIBifIndex

Column	Syntax	OID
p2mpLocalLoopbackMode This object is used to configure the system in loopback mode prior to executing some system diagnostic tests. The user selects the point in the system where the data signal should be looped back. The diagnostic test…	Enumerationr/w Enumerated Values: 1 noLoopback 2 fir 3 if 4 rf	.1.3.6.1.4.1.9.9.170.1.1.3.1.1.1
p2mpLocalLoopbackAntenna This object identifies the RF resource used for loopback testing. This object is not applicable for loopback testing when p2mpLocalLoopbackMode has a value of 'noLoopback(1)'.	CISCO-WIRELESS-TC-MIBCwrRfTyper/w Type Values: 0 main 1 diversity	.1.3.6.1.4.1.9.9.170.1.1.3.1.1.2
p2mpLocalLoopbackChannel This object identifies the channel being used to loopback the data. This object is not applicable for loopback testing when p2mpLocalLoopbackMode has a value of 'noLoopback(1)'.	Unsigned32r/w Constraints: range: 1-7	.1.3.6.1.4.1.9.9.170.1.1.3.1.1.3

Entity (Light emitting diode) LED information.  For each LED on
the entity, an entry will exist in this table, describing the
location and current status of that LED.

p2mpLedEntry row .1.3.6.1.4.1.9.9.170.1.1.4.1.1

An entry in the table, containing the LED information.
The entPhysicalIndex identifies the entity on which the LED's
are present.

Indexes

ENTITY-MIBentPhysicalIndex p2mpLedIndex

Column	Syntax	OID
p2mpLedIndex For a given entPhysicalIndex, this index value uniquely identifies an entry in the p2mpLedTable.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.9.9.170.1.1.4.1.1.1
p2mpLedType Indicates the type or label of the LED.	Enumeration Enumerated Values: 0 interfaceEnable 1 majorAlarm 2 minorAlarm 3 outOfService 4 carrier 5 transmitData 6 receiveData	.1.3.6.1.4.1.9.9.170.1.1.4.1.1.2
p2mpLedState Indicates the state of the LED.	Enumeration Enumerated Values: 0 off 1 green 2 yellow	.1.3.6.1.4.1.9.9.170.1.1.4.1.1.3

This table contains information about the currently configured
physical layer interfaces in the subscriber unit.

p2mpSuRadioPhyEntry row .1.3.6.1.4.1.9.9.170.1.2.1.1

An entry containing the radio configuration information
of the propDocsWirelessMaclayer interface in the
subscriber unit.

The entry is created when a propDocsWirelessMaclayer
interface is detected in the s…

Indexes

IF-MIBifIndex

Column	Syntax	OID
p2mpSuTxMuteEnable When true(1), this object indicates the subscriber unit transmission has been turned off for a duration indicated by p2mpSuTxMuteDuration. When false(2), this object indicates that the subscriber unit is transmitting.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.170.1.2.1.1.1
p2mpSuTxMuteDuration This object indicates the duration of time (in minutes) for which the subscriber transmission will be turned off.	minutesUnsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.9.9.170.1.2.1.1.2

This table contains information about the receive power 
measured at the different possible center frequencies.

p2mpSuPowerScanEntry row .1.3.6.1.4.1.9.9.170.1.2.2.1

An entry containing the power related status
information of the propDocsWirelessMaclayer
interface in the subscriber unit.

The entry is created when a propDocsWirelessMaclayer
interface is detected in th…

Indexes

IF-MIBifIndex p2mpSuPowerScanIndex

Column	Syntax	OID
p2mpSuPowerScanIndex For a given ifIndex, this index value uniquely identifies an entry in the p2mpSuPowerScanTable.	Integer32 Constraints: range: 1-20	.1.3.6.1.4.1.9.9.170.1.2.2.1.1
p2mpSuCenterFrequency This object indicates the frequency at which the receive power at the subscriber unit was measured.	KHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange Type Constraints: range: 0..60000000	.1.3.6.1.4.1.9.9.170.1.2.2.1.2
p2mpSuMeasuredPower This object represents the power measured at the frequency indicated by p2mpSuCenterFrequency.	dBmInteger32 Constraints: range: -127-50	.1.3.6.1.4.1.9.9.170.1.2.2.1.3

This table contains Automatic Line Control (ALC) configuration 
information.  It is supported at the head end only.

p2mpHeAlcEntry row .1.3.6.1.4.1.9.9.170.1.3.1.1

An entry containing the ALC configuration information
the propDocsWirelessMaylayer interface at the head end.

The entry is created when a propDocsWirelessMaclayer
interface is detected in the head end uni…

Indexes

IF-MIBifIndex

Column	Syntax	OID
p2mpHeAlcEnable This object is used to enable/disable ALC at the Head End. A value of true(1), indicates that ALC is enabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.170.1.3.1.1.1
p2mpHeAlcInterval This object represents the scheduling interval. It is the regular interval at which the ALC grant in Map is transmitted to the SU's	millisecondsUnsigned32r/w Constraints: range: 32-1024	.1.3.6.1.4.1.9.9.170.1.3.1.1.2
p2mpHeAlcNumMiniSlots This indicates the number of minislots within each grant.	Unsigned32r/w Constraints: range: 1-4	.1.3.6.1.4.1.9.9.170.1.3.1.1.3

This table contains information about the state of the 
intermediate frequency subsystem in the radio system.  This
table is supported at the head end only.

p2mpHeIntFreqEntry row .1.3.6.1.4.1.9.9.170.1.3.2.1

The entry of this table is created when the managed system
detects a propDocsWirelessMaclayer interface in the head
end unit.
The entry is deleted when the associated
propDocsWirelessMaclayer interface is removed.

Indexes

IF-MIBifIndex

Column	Syntax	OID
p2mpHeIfTxOscState This object indicates the state of the IF transmit oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.	CISCO-WIRELESS-TC-MIBCwrOscState Type Values: 1 oscillatorOk 2 osccillatorBad	.1.3.6.1.4.1.9.9.170.1.3.2.1.1
p2mpHeIfRxOscState This object indicates the state of the IF receive oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.	CISCO-WIRELESS-TC-MIBCwrOscState Type Values: 1 oscillatorOk 2 osccillatorBad	.1.3.6.1.4.1.9.9.170.1.3.2.1.2
p2mpHeIfRefOscState This object indicates the state of the IF reference oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.	CISCO-WIRELESS-TC-MIBCwrOscState Type Values: 1 oscillatorOk 2 osccillatorBad	.1.3.6.1.4.1.9.9.170.1.3.2.1.3
p2mpHeIfInpFreq This object represents the IF input frequency.	KHzUnsigned32 Constraints: range: 1000-500000	.1.3.6.1.4.1.9.9.170.1.3.2.1.4
p2mpHeIfOutFreq This object represents the IF output frequency.	KHzUnsigned32 Constraints: range: 1000-500000	.1.3.6.1.4.1.9.9.170.1.3.2.1.5
p2mpHeTrapEnable When set to true(1), this enables the notifications that are specific to the head end. When set to false(2), these notifications are disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.170.1.3.2.1.6