CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB Table View

This table provides REP configuration for interfaces in the
device.  This table contains one entry for each interface
running REP.

crepInterfaceConfigEntry row .1.3.6.1.4.1.9.9.601.1.2.1.1

An entry exists for each interface, if REP is configured on it.
On a system that supports REP, all ports with ifType =
'ethernetCsmacd' and those ethernet based virtual ports with
ifType = 'propVirtual' also support R…

Indexes

crepIfIndex

Column	Syntax	OID
crepIfIndex This object identifies the ifIndex-value assigned to the interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.601.1.2.1.1.1
crepIfSegmentId This object specifies the segment that the interface is part. This object can be modified when crepIfConfigRowStatus is 'active'. The valid range is from crepMinSegmentId to crepMaxSegmentId.	RepSegmentIdr/w	.1.3.6.1.4.1.9.9.601.1.2.1.1.2
crepIfOperStatus This object indicates the current operational link state of the REP port. If a REP configured interface is down, it will be in 'initDown' state. 'none' - REP is not operational on the interface.…	Enumeration Enumerated Values: 1 none 2 initDown 3 noNeighbour 4 oneWay 5 twoWay 6 flapping 7 wait 8 unknown	.1.3.6.1.4.1.9.9.601.1.2.1.1.3
crepIfPortRole This object indicates the role or state of a REP port depending on its link status and whether it is forwarding or blocking traffic. 'failedPort' - a port with a non-operational link status, …	Enumeration Enumerated Values: 1 failedPort 2 alternatePort 3 openPort 4 failedPortNoNeighbor 5 failedPortLogicalOpen	.1.3.6.1.4.1.9.9.601.1.2.1.1.4
crepIfPortID This object indicates the REP port identifier automatically assigned by REP when enabled.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.9.9.601.1.2.1.1.5
crepIfAdminEdgePortType This object specifies the configured edge port type for the interface.	RepPortTyper/w Type Values: 1 notEdge 2 edge 3 edgePrimary 4 edgeNoNeighbor 5 edgeNoNeighborPrimary	.1.3.6.1.4.1.9.9.601.1.2.1.1.6
crepIfOperEdgePortType This object indicates the actual edge port type for the interface. Value 'edge' indicates that the port is secondary edge port.	RepPortType Type Values: 1 notEdge 2 edge 3 edgePrimary 4 edgeNoNeighbor 5 edgeNoNeighborPrimary	.1.3.6.1.4.1.9.9.601.1.2.1.1.7
crepIfPreferredConfig This object specifies if port should get preference to become the alternate port among other equal ports in the segment. Setting this value to true does not guaranty that the port will become the alternat…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.601.1.2.1.1.8
crepifBlockedVlans1k This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 0 through 1023. If the bit is set to '1', then the VLAN is marked for blocking. This value …	CISCO-TCCiscoVlanListr/w Type Constraints: range: 0..128	.1.3.6.1.4.1.9.9.601.1.2.1.1.9
crepifBlockedVlans2k This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 1024 through 2047. If the bit is set to '1', then the VLAN is marked for blocking. This val…	CISCO-TCCiscoVlanListr/w Type Constraints: range: 0..128	.1.3.6.1.4.1.9.9.601.1.2.1.1.10
crepifBlockedVlans3k This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 2048 through 3071. If the bit is set to '1', then the VLAN is marked for blocking. This val…	CISCO-TCCiscoVlanListr/w Type Constraints: range: 0..128	.1.3.6.1.4.1.9.9.601.1.2.1.1.11
crepifBlockedVlans4k This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 3072 through 4095. If the bit is set to '1', then the VLAN is marked for blocking. This val…	CISCO-TCCiscoVlanListr/w Type Constraints: range: 0..128	.1.3.6.1.4.1.9.9.601.1.2.1.1.12
crepLoadBalanceBlockPortType This object specifies the method defined to identify the alternate port in the segment that takes part in VLAN load balancing by blocking a subset of VLANs after preemption. 'none' - no method i…	Enumerationr/w Enumerated Values: 1 none 2 offset 3 portId 4 prefFlag	.1.3.6.1.4.1.9.9.601.1.2.1.1.13
crepBlockPortNumInfo This object specifies the offset of the port in the segment to be blocked for VLAN load balancing. Positive numbers indicate the offset from the primary edge port and negative numbers indicates the downstream neighbor…	Integer32r/w Constraints: range: -256-256	.1.3.6.1.4.1.9.9.601.1.2.1.1.14
crepBlockPortIdInfo This object specifies the port identifier of the port in the segment to be blocked for VLAN load balancing. 'crepIfPortID' object of the corresponding port provides the port identifier. This value is onl…	OctetStringr/w Constraints: range: 8-8	.1.3.6.1.4.1.9.9.601.1.2.1.1.15
crepIfPreemptDelayTimer This object specifies the interval of time that REP waits before triggering preemption after the segment is complete. The value -1 is used to indicate that no time delay is configured and the preemption w…	delay in secondsInteger32r/w Constraints: range: -1-300	.1.3.6.1.4.1.9.9.601.1.2.1.1.16
crepIfStcnPropagateToSTP This object specifies if the REP edge propagates the segment topology change notifications to the spanning tree network. This value is only effective on the device acting as the REP primary edge.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.601.1.2.1.1.17
crepIfStcnPropagateToOtherSegs This object specifies the list of segments to which the REP edge propagates the segment topology change notifications. This value is only effective on the device acting as the REP primary edge.	RepSegmentListr/w	.1.3.6.1.4.1.9.9.601.1.2.1.1.18
crepIfStcnPropagateToIf This object specifies the interface to which the REP edge should propagate the segment topology change notifications. The interface should be of type ifType = 'ethernetCsmacd' or an ethernet based virtual port with ifT…	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.9.9.601.1.2.1.1.19
crepIfConfigRowStatus This object is used to manage the creation, deletion, and modification of rows in this table. A row may be created using the 'CreateAndGo' option. When the row is successfully created, the agent would se…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.601.1.2.1.1.20

A table for REP interfaces statistics.
This table augments the crepInterfaceConfigTable.

crepInterfaceStatsEntry row .1.3.6.1.4.1.9.9.601.1.2.2.1

The counter entries are not persistent. This is because
once REP is un-configured on the interface the row would be
deleted and hence they will restart if REP is configured
once again on the interface. NMS need to ch…

Indexes

No indexes recorded

Column	Syntax	OID
crepCounterDiscontinuityTime The value of sysUpTime on the most recent occasion at which REP counters suffered a discontinuity on this interface. If no such discontinuities have occurred since the first initialization of REP, then this object cont…	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.601.1.2.2.1.1
crepLslRxPdus This object indicates the number of link status layer PDUs received on the port.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.2
crepLslTxPdus This object indicates the number of link status layer PDUs transmitted on the port.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.3
crepHflRxPdus This object indicates the number of hardware flood layer PDUs received on the port.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.4
crepHflTxPdus This object indicates the number of hardware flood layer PDUs transmitted on the port.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.5
crepBpaTlvRxPackets This object indicates the number of blocked port advertisement TLVs received on the port.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.6
crepBpaTlvTxPackets This object indicates the number of blocked port advertisement TLVs transmitted on the port.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.7
crepBpaStcnLslRxPackets This object indicates the number of segment topology change notifications received as blocked port advertisement through link status layer.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.8
crepBpaStcnLslTxPackets This object indicates the number of segment topology change notifications transmitted as blocked port advertisement through link status layer.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.9
crepBpaStcnHflRxPackets This object indicates the number of segment topology change notifications received as blocked port advertisement through hardware flood layer.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.10
crepBpaStcnHflTxPackets This object indicates the number of segment topology change notifications transmitted as blocked port advertisement through hardware flood layer.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.11
crepEpaElectionTlvRxPackets This object indicates the number of end port advertisement election TLVs received that are used for determining the role, namely primary edge or secondary edge.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.12
crepEpaElectionTlvTxPackets This object indicates the number of end port advertisement election TLVs transmitted that are used for determining the role, namely primary edge or secondary edge.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.13
crepEpaCommandTlvRxPackets This object indicates the number of end port advertisement command TLVs received that are used to authorize a port to takeover the segment for the purpose of VLAN load balancing.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.14
crepEpaCommandTlvTxPackets This object indicates the number of end port advertisement command TLVs transmitted that are used to authorize a port to takeover the segment for the purpose of VLAN load balancing.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.15
crepEpaInfoTlvRxPackets This object indicates the number of end port advertisement information TLVs received on the port. These messages are sent by the end ports (configured edge port, or port which is down or port which does not have intern…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.16
crepEpaInfoTlvTxPackets This object indicates the number of end port advertisement information TLVs transmitted on the port. These messages are sent by the end ports (configured edge port, or port which is down or port which does not have int…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.601.1.2.2.1.17

This table specifies REP segments configured on the
device.

crepSegmentEntry row .1.3.6.1.4.1.9.9.601.1.3.1.1

A list of REP segment entries.

The number of segments configured on the device determines
the number of entries. An entry is created when a segment
identifier value is configured on an interface and no
ma…

Indexes

crepSegmentId

Column	Syntax	OID
crepSegmentId This object identifies the segment identifier.	RepSegmentId	.1.3.6.1.4.1.9.9.601.1.3.1.1.1
crepSegmentInterface1 This object indicates the ifIndex-value assigned to the first interface that is part of the segment.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.601.1.3.1.1.2
crepSegmentInterface2 This object indicates the ifIndex-value assigned to the second interface that is part of the segment. The value of zero means that the InterfaceIndex is not known. The reasons for value being zero might…	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.9.9.601.1.3.1.1.3
crepSegmentComplete This object indicates if the segment is complete such that no port in the segment is in failed state.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.601.1.3.1.1.4
crepSegmentPreempt This object should be set to true by NMS for triggering manual preemption. This may cause a momentary traffic disruption. Though this can be done for any node in the segment, it is only effective on the …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.601.1.3.1.1.5
crepSegmentPreemptStatus This object indicates the status of the last preemption trigger. 'none' - preemption trigger is not executed. 'preemptSuccessful' - preemption action for the previous …	Enumeration Enumerated Values: 1 none 2 preemptSuccessful 3 preemptFailure 4 preemptTrigger 5 preemptTriggerFailure	.1.3.6.1.4.1.9.9.601.1.3.1.1.6