crepIfSegmentId
CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB ·
.1.3.6.1.4.1.9.9.601.1.2.1.1.2
Object
column
r/w
RepSegmentId
This object specifies the segment that the interface is part.
This object can be modified when crepIfConfigRowStatus is 'active'.
The valid range is from crepMinSegmentId to crepMaxSegmentId.
Context
- MIB
- CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
- OID
.1.3.6.1.4.1.9.9.601.1.2.1.1.2- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- crepInterfaceConfigEntry
- Table
- crepInterfaceConfigTable
- Siblings
- 19
Syntax
RepSegmentId
- Source
- RepSegmentId
- Base type
Unsigned32
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| crepIfIndex This object identifies the ifIndex-value assigned to the
interface. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.9.9.601.1.2.1.1.1 |
| crepifBlockedVlans2k This object specifies the list of VLANs configured to be
blocked at the alternate port for VLANs with values of 1024
through 2047. If the bit is set to '1', then the VLAN is mark… | column | CISCO-TCCiscoVlanList | .1.3.6.1.4.1.9.9.601.1.2.1.1.10 |
| crepifBlockedVlans3k This object specifies the list of VLANs configured to be
blocked at the alternate port for VLANs with values of 2048
through 3071. If the bit is set to '1', then the VLAN is mark… | column | CISCO-TCCiscoVlanList | .1.3.6.1.4.1.9.9.601.1.2.1.1.11 |
| crepifBlockedVlans4k This object specifies the list of VLANs configured to be
blocked at the alternate port for VLANs with values of 3072
through 4095. If the bit is set to '1', then the VLAN is mark… | column | CISCO-TCCiscoVlanList | .1.3.6.1.4.1.9.9.601.1.2.1.1.12 |
| crepLoadBalanceBlockPortType This object specifies the method defined to identify the
alternate port in the segment that takes part in VLAN load
balancing by blocking a subset of VLANs after preemption. … | column | Enumeration | .1.3.6.1.4.1.9.9.601.1.2.1.1.13 |
| crepBlockPortNumInfo This object specifies the offset of the port in the segment
to be blocked for VLAN load balancing. Positive numbers
indicate the offset from the primary edge port and negative
n… | column | Integer32 | .1.3.6.1.4.1.9.9.601.1.2.1.1.14 |
| crepBlockPortIdInfo This object specifies the port identifier of the port in the
segment to be blocked for VLAN load balancing. 'crepIfPortID'
object of the corresponding port provides the port iden… | column | OctetString | .1.3.6.1.4.1.9.9.601.1.2.1.1.15 |
| crepIfPreemptDelayTimer This object specifies the interval of time that REP waits
before triggering preemption after the segment is complete.
The value -1 is used to indicate that no time … | column | delay in seconds Integer32 | .1.3.6.1.4.1.9.9.601.1.2.1.1.16 |
| crepIfStcnPropagateToSTP This object specifies if the REP edge propagates the
segment topology change notifications to the spanning
tree network.
This value is only effective on the device… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.601.1.2.1.1.17 |
| crepIfStcnPropagateToOtherSegs This object specifies the list of segments to which the
REP edge propagates the segment topology change notifications.
This value is only effective on the device ac… | column | RepSegmentList | .1.3.6.1.4.1.9.9.601.1.2.1.1.18 |
| crepIfStcnPropagateToIf This object specifies the interface to which the REP edge
should propagate the segment topology change notifications.
The interface should be of type ifType = 'ethernetCsmacd'
or… | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.9.9.601.1.2.1.1.19 |
| crepIfConfigRowStatus This object is used to manage the creation, deletion, and
modification of rows in this table.
A row may be created using the 'CreateAndGo' option. When the
row is … | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.9.9.601.1.2.1.1.20 |
| crepIfOperStatus This object indicates the current operational link state
of the REP port. If a REP configured interface is down,
it will be in 'initDown' state.
'none' - … | column | Enumeration | .1.3.6.1.4.1.9.9.601.1.2.1.1.3 |
| crepIfPortRole This object indicates the role or state of a REP port depending
on its link status and whether it is forwarding or blocking
traffic.
'failedPort' - a port with … | column | Enumeration | .1.3.6.1.4.1.9.9.601.1.2.1.1.4 |
| crepIfPortID This object indicates the REP port identifier automatically
assigned by REP when enabled. | column | OctetString | .1.3.6.1.4.1.9.9.601.1.2.1.1.5 |
| crepIfAdminEdgePortType This object specifies the configured edge port type for the
interface. | column | RepPortType | .1.3.6.1.4.1.9.9.601.1.2.1.1.6 |
| crepIfOperEdgePortType This object indicates the actual edge port type for the
interface. Value 'edge' indicates that the port is secondary
edge port. | column | RepPortType | .1.3.6.1.4.1.9.9.601.1.2.1.1.7 |
| crepIfPreferredConfig This object specifies if port should get preference to become
the alternate port among other equal ports in the segment.
Setting this value to true does not guarant… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.9.601.1.2.1.1.8 |
| crepifBlockedVlans1k This object specifies the list of VLANs configured to be
blocked at the alternate port for VLANs with values of 0 through
1023. If the bit is set to '1', then the VLAN is marked … | column | CISCO-TCCiscoVlanList | .1.3.6.1.4.1.9.9.601.1.2.1.1.9 |