crepBlockPortNumInfo

CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB · .1.3.6.1.4.1.9.9.601.1.2.1.1.14

Object

column r/w Integer32

This object specifies the offset of the port in the segment
to be blocked for VLAN load balancing.  Positive numbers 
indicate the offset from the primary edge port and negative
numbers indicates the downstream neighbor from the secondary
edge port.     
              
[Sw E1]E1---NE1[Sw 1]NE2---NE1[Sw 2]NE2.........
                                               .
                                               .
[Sw E2]E2---NE2[Sw N]NE1---NE2[Sw N-1]NE1.......
              
 Sw : Switch.
 E  : Edge port.
 NE : Non-Edge port.  
 E1/E2: Edge switches.  E1 and E2 can either be same or 
 different switches.
              
In the segment depicted above, consider port E1 on 'Sw E1' is 
the primary edge and E2 on 'Sw E2' is the secondary edge.  
Value 1 for this object indicates primary edge port, 2 indicates
NE1 on 'Sw 1', 3 indicates NE2 on 'Sw 1' and so on.  Value -1 
indicates secondary edge port, -2 indicates NE2 on 'Sw N', -3 
indicates NE1 on 'Sw N' and so on.  Usage of value 0 is invalid.
              
This value is only effective on the device acting as the REP
primary edge and has relevance only if 
crepLoadBalanceBlockPortType = 'offset'.

Context

MIB: CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB
OID: .1.3.6.1.4.1.9.9.601.1.2.1.1.14
Type: column
Access: readwrite
Status: current
Parent: crepInterfaceConfigEntry
Table: crepInterfaceConfigTable
Siblings: 19

Syntax

Integer32

Values & Constraints

Object Constraints

range: -256-256

Related Objects

Sibling Objects

Object	Type	Syntax	OID
crepIfIndex This object identifies the ifIndex-value assigned to the interface.	column	IF-MIBInterfaceIndex	`.1.3.6.1.4.1.9.9.601.1.2.1.1.1`
crepifBlockedVlans2k This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 1024 through 2047. If the bit is set to '1', then the VLAN is mark…	column	CISCO-TCCiscoVlanList	`.1.3.6.1.4.1.9.9.601.1.2.1.1.10`
crepifBlockedVlans3k This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 2048 through 3071. If the bit is set to '1', then the VLAN is mark…	column	CISCO-TCCiscoVlanList	`.1.3.6.1.4.1.9.9.601.1.2.1.1.11`
crepifBlockedVlans4k This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 3072 through 4095. If the bit is set to '1', then the VLAN is mark…	column	CISCO-TCCiscoVlanList	`.1.3.6.1.4.1.9.9.601.1.2.1.1.12`
crepLoadBalanceBlockPortType This object specifies the method defined to identify the alternate port in the segment that takes part in VLAN load balancing by blocking a subset of VLANs after preemption. …	column	Enumeration	`.1.3.6.1.4.1.9.9.601.1.2.1.1.13`
crepBlockPortIdInfo This object specifies the port identifier of the port in the segment to be blocked for VLAN load balancing. 'crepIfPortID' object of the corresponding port provides the port iden…	column	OctetString	`.1.3.6.1.4.1.9.9.601.1.2.1.1.15`
crepIfPreemptDelayTimer This object specifies the interval of time that REP waits before triggering preemption after the segment is complete. The value -1 is used to indicate that no time …	column	delay in seconds Integer32	`.1.3.6.1.4.1.9.9.601.1.2.1.1.16`
crepIfStcnPropagateToSTP This object specifies if the REP edge propagates the segment topology change notifications to the spanning tree network. This value is only effective on the device…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.601.1.2.1.1.17`
crepIfStcnPropagateToOtherSegs This object specifies the list of segments to which the REP edge propagates the segment topology change notifications. This value is only effective on the device ac…	column	RepSegmentList	`.1.3.6.1.4.1.9.9.601.1.2.1.1.18`
crepIfStcnPropagateToIf This object specifies the interface to which the REP edge should propagate the segment topology change notifications. The interface should be of type ifType = 'ethernetCsmacd' or…	column	IF-MIBInterfaceIndexOrZero	`.1.3.6.1.4.1.9.9.601.1.2.1.1.19`
crepIfSegmentId This object specifies the segment that the interface is part. This object can be modified when crepIfConfigRowStatus is 'active'. The valid range is from crepMinSeg…	column	RepSegmentId	`.1.3.6.1.4.1.9.9.601.1.2.1.1.2`
crepIfConfigRowStatus This object is used to manage the creation, deletion, and modification of rows in this table. A row may be created using the 'CreateAndGo' option. When the row is …	column	SNMPv2-TCRowStatus	`.1.3.6.1.4.1.9.9.601.1.2.1.1.20`
crepIfOperStatus This object indicates the current operational link state of the REP port. If a REP configured interface is down, it will be in 'initDown' state. 'none' - …	column	Enumeration	`.1.3.6.1.4.1.9.9.601.1.2.1.1.3`
crepIfPortRole This object indicates the role or state of a REP port depending on its link status and whether it is forwarding or blocking traffic. 'failedPort' - a port with …	column	Enumeration	`.1.3.6.1.4.1.9.9.601.1.2.1.1.4`
crepIfPortID This object indicates the REP port identifier automatically assigned by REP when enabled.	column	OctetString	`.1.3.6.1.4.1.9.9.601.1.2.1.1.5`
crepIfAdminEdgePortType This object specifies the configured edge port type for the interface.	column	RepPortType	`.1.3.6.1.4.1.9.9.601.1.2.1.1.6`
crepIfOperEdgePortType This object indicates the actual edge port type for the interface. Value 'edge' indicates that the port is secondary edge port.	column	RepPortType	`.1.3.6.1.4.1.9.9.601.1.2.1.1.7`
crepIfPreferredConfig This object specifies if port should get preference to become the alternate port among other equal ports in the segment. Setting this value to true does not guarant…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.601.1.2.1.1.8`
crepifBlockedVlans1k This object specifies the list of VLANs configured to be blocked at the alternate port for VLANs with values of 0 through 1023. If the bit is set to '1', then the VLAN is marked …	column	CISCO-TCCiscoVlanList	`.1.3.6.1.4.1.9.9.601.1.2.1.1.9`