CISCO-IETF-PIM-MIB Table View

The (conceptual) table listing the router's PIM interfaces.
Along with PIM IGMP or MLD is enabled on all interfaces 
listed in this table.

cPimIfEntry row .1.3.6.1.4.1.9.10.119.1.1.2.1

An entry (conceptual row) in the pimIfTable.

Indexes

cPimIfIndex cPimIfInetVersion

Column	Syntax	OID
cPimIfIndex The ifIndex value of this PIM interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.10.119.1.1.2.1.1
cPimIfInetVersion The Inet version of this row.	INET-ADDRESS-MIBInetVersion Type Values: 0 unknown 1 ipv4 2 ipv6	.1.3.6.1.4.1.9.10.119.1.1.2.1.2
cPimIfAddressType This objects identifies type of InetAddress presented in cPimIfAddress and cPimIfDR	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.10.119.1.1.2.1.3
cPimIfAddress The Inet address of the PIM interface.	OctetStringr/w Constraints: range: 4-4 range: 16-16 range: 20-20	.1.3.6.1.4.1.9.10.119.1.1.2.1.4
cPimIfNetMask The network mask for the IP address of the PIM interface.	INET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.9.10.119.1.1.2.1.5
cPimIfMode The configured mode of this PIM interface. A value of sparseDense is only valid for PIMv1. dense (1): indicates interface is running PIM dense mode sparse (2): indicates interf…	Enumerationr/w Enumerated Values: 1 dense 2 sparse 3 sparseDense	.1.3.6.1.4.1.9.10.119.1.1.2.1.6
cPimIfDR The Designated Router on this PIM interface. For point-to- point interfaces, this object has the value 0.0.0.0 or 0::0	OctetString Constraints: range: 4-4 range: 16-16 range: 20-20	.1.3.6.1.4.1.9.10.119.1.1.2.1.7
cPimIfHelloInterval The frequency at which PIM Hello messages are transmitted on this interface.	secondsUnsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.9.10.119.1.1.2.1.8
cPimIfJoinPruneInterval The frequency at which PIM Join/Prune messages are transmitted on this PIM interface. The default value of this object is the pimJoinPruneInterval.	secondsUnsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.9.10.119.1.1.2.1.9
cPimIfCBSRPreference The preference value for the local interface as a candidate bootstrap router. The value of -1 is used to indicate that the local interface is not a candidate BSR interface.	Integer32r/w Constraints: range: -1-255	.1.3.6.1.4.1.9.10.119.1.1.2.1.10
cPimIfStatus The status of this entry. Creating the entry enables PIM on the interface; destroying the entry disables PIM on the interface.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.10.119.1.1.2.1.11

The (conceptual) table listing the router's PIM neighbors.

cPimNbrEntry row .1.3.6.1.4.1.9.10.119.1.1.3.1

An entry (conceptual row) in the pimNbrTable.

Indexes

cPimNbrIfIndex cPimNbrAddressType cPimNbrAddress

Column	Syntax	OID
cPimNbrIfIndex The value of ifIndex for the interface used to reach this PIM neighbor.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.10.119.1.1.3.1.1
cPimNbrAddressType This objects identifies type of InetAddress presented in cPimNbrAddress.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.10.119.1.1.3.1.2
cPimNbrAddress The IP address of the PIM neighbor for which this entry contains information.	OctetString Constraints: range: 4-4 range: 16-16 range: 20-20	.1.3.6.1.4.1.9.10.119.1.1.3.1.3
cPimNbrUpTime The time since this PIM neighbor (last) became a neighbor of the local router.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.10.119.1.1.3.1.4
cPimNbrExpiryTime The minimum time remaining before this PIM neighbor will be aged out.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.10.119.1.1.3.1.5

The (conceptual) table listing PIM-specific information on
a subset of the rows of the cIpMRouteTable defined in the IP
Multicast MIB.

cPimInetMRouteEntry row .1.3.6.1.4.1.9.10.119.1.1.4.1

An entry (conceptual row) in the cPimInetMRouteTable. There
is one entry per entry in the cIpMRouteTable whose incoming
interface is running PIM.

Indexes

CISCO-IETF-IPMROUTE-MIBcIpMRouteAddrType CISCO-IETF-IPMROUTE-MIBcIpMRouteGroup CISCO-IETF-IPMROUTE-MIBcIpMRouteSource CISCO-IETF-IPMROUTE-MIBcIpMRouteSourceMask

Column	Syntax	OID
cPimInetMRouteUpstreamAssertTime The time remaining before the router changes its upstream neighbor back to its RPF neighbor. This timer is called the Assert timer in the PIM Sparse and Dense mode specification. A value of 0 indicates t…	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.10.119.1.1.4.1.1
cPimInetMRouteAssertMetric The metric advertised by the assert winner on the upstream interface, or 0 if no such assert is in received.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.9.10.119.1.1.4.1.2
cPimInetMRouteAssertMetricPref The preference advertised by the assert winner on the upstream interface, or 0 if no such assert is in effect.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.9.10.119.1.1.4.1.3
cPimInetMRouteAssertRPTBit The value of the RPT-bit advertised by the assert winner on the upstream interface, or false if no such assert is in effect.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.10.119.1.1.4.1.4
cPimInetMRouteFlags This object describes PIM-specific flags related to a multicast state entry. rpt (0): indicates the route is a shared-tree or RP-tree route. spt (1): indicates the route is a shor…	Bits Enumerated Values: 0 rpt 1 spt	.1.3.6.1.4.1.9.10.119.1.1.4.1.5

The (conceptual) table listing PIM-specific information on
a subset of the rows of the cIpMRouteNextHopTable defined in
the IP Multicast MIB.

cPimInetMRouteNextHopEntry row .1.3.6.1.4.1.9.10.119.1.1.5.1

An entry (conceptual row) in the cPimInetMRouteNextHopTable.
There is one entry per entry in the cIpMRouteNextHopTable
whose interface is running PIM and whose
cIpMRouteNextHopState is pruned(1).

Indexes

CISCO-IETF-IPMROUTE-MIBcIpMRouteNextHopAddrType CISCO-IETF-IPMROUTE-MIBcIpMRouteNextHopGroup CISCO-IETF-IPMROUTE-MIBcIpMRouteNextHopSource CISCO-IETF-IPMROUTE-MIBcIpMRouteNextHopSourceMask CISCO-IETF-IPMROUTE-MIBcIpMRouteNextHopIfIndex CISCO-IETF-IPMROUTE-MIBcIpMRouteNextHopAddress

Column	Syntax	OID
cPimInetMRouteNextHopPruneReason This object indicates the reason why downstream interface was pruned, prune (1): indicates downstream interface was pruned in response to a PIM prune message. assert (3): indic…	Enumeration Enumerated Values: 1 other 2 prune 3 assert	.1.3.6.1.4.1.9.10.119.1.1.5.1.2

The (conceptual) table listing PIM information for
candidate Rendezvous Points (RPs) for IP multicast groups.
When the local router is the BSR, this information is
obtained from received Candidate-RP-Advertisements.  When
the local router is not the BSR, this information is
obtained from received RP-Set messages.

cPimRPMapEntry row .1.3.6.1.4.1.9.10.119.1.1.6.1

An entry (conceptual row) in the pimRPsTable.

Indexes

cPimRPMapComponent cPimRPMapAddrType cPimRPMapGroupAddress cPimRPMapGroupMask cPimRPMapAddress

Column	Syntax	OID
cPimRPMapComponent A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.	Unsigned32 Constraints: range: 1-255	.1.3.6.1.4.1.9.10.119.1.1.6.1.1
cPimRPMapAddrType Type of Inet address presented in this row. This includes cPimRPMapGroupAddress and cPimRPMapAddress	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.10.119.1.1.6.1.2
cPimRPMapGroupAddress The IP multicast group address which, when combined with pimRPsGroupMask, gives the group prefix for which this entry contains information about the Candidate-RP.	OctetString Constraints: range: 20-20 range: 16-16 range: 4-4	.1.3.6.1.4.1.9.10.119.1.1.6.1.3
cPimRPMapGroupMask The multicast group address mask which, when combined with pimRPsGroupAddress, gives the group prefix for which this entry contains information about the Candidate-RP.	INET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.9.10.119.1.1.6.1.4
cPimRPMapAddress The IP address of the Candidate-RP.	OctetString Constraints: range: 4-4 range: 16-16 range: 20-20	.1.3.6.1.4.1.9.10.119.1.1.6.1.5
cPimRPMapHoldTime The holdtime of a Candidate-RP. If the local router is not the BSR, this value is 0.	secondsUnsigned32 Constraints: range: 0-255	.1.3.6.1.4.1.9.10.119.1.1.6.1.6
cPimRPMapExpiryTime The minimum time remaining before the Candidate-RP will be declared down. If the local router is not the BSR, this value is 0.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.10.119.1.1.6.1.7

The (conceptual) table listing the IP multicast groups for
which the local router is to advertise itself as a
Candidate-RP when the value of cPimComponentCRPHoldTime is
non-zero.  If this table is empty, then the local router
will advertise itself as a Candidate-RP for all groups
(providing the value of cPimComponentCRPHoldTime is non-
zero).

cPimCRPEntry row .1.3.6.1.4.1.9.10.119.1.1.7.1

An entry (conceptual row) in the cPimCRPTable.

Indexes

cPimCRPAddrType cPimCRPGroupAddress cPimCRPGroupMask

Column	Syntax	OID
cPimCRPAddrType Type of Inet address presented in this row. This includes cPimCRPGroupAddress and cPimCRPAddress	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.10.119.1.1.7.1.1
cPimCRPGroupAddress The IP multicast group address which, when combined with cPimCRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP.	OctetString Constraints: range: 4-4 range: 16-16 range: 20-20	.1.3.6.1.4.1.9.10.119.1.1.7.1.2
cPimCRPGroupMask The multicast group address mask which, when combined with cPimCRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP.	INET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.9.10.119.1.1.7.1.3
cPimCRPAddress The (unicast) address of the interface which will be advertised as a Candidate-RP.	OctetStringr/w Constraints: range: 4-4 range: 16-16 range: 20-20	.1.3.6.1.4.1.9.10.119.1.1.7.1.4
cPimCRPRowStatus The status of this row, by which new entries may be created, or old entries deleted from this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.10.119.1.1.7.1.5

The (conceptual) table containing objects specific to a PIM
domain.  One row exists for each domain to which the router
is connected.  A PIM-SM domain is defined as an area of the
network over which Bootstrap messages are forwarded.
Typically, a PIM-SM router will be a member of exactly one
domain.  This table also supports, however, routers which
may form a border between two PIM-SM domains and do not
forward Bootstrap messages between them.

cPimComponentEntry row .1.3.6.1.4.1.9.10.119.1.1.8.1

An entry (conceptual row) in the cPimComponentTable.

Indexes

cPimComponentIndex

Column	Syntax	OID
cPimComponentIndex A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value. Routers that only support membership in a single PIM-SM domain should use a cPimC…	Unsigned32 Constraints: range: 1-255	.1.3.6.1.4.1.9.10.119.1.1.8.1.1
cPimComponentBSRAddrType Type of Inet address presented in cPimComponentBSRAddress.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.10.119.1.1.8.1.2
cPimComponentBSRAddress The IP address of the bootstrap router (BSR) for the local PIM region.	OctetStringr/w Constraints: range: 4-4 range: 16-16 range: 20-20	.1.3.6.1.4.1.9.10.119.1.1.8.1.3
cPimComponentBSRExpiryTime The minimum time remaining before the bootstrap router in the local domain will be declared down. For candidate BSRs, this is the time until the component sends an RP-Set message. For other routers, this is the time u…	SNMPv2-SMITimeTicksr/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.10.119.1.1.8.1.4
cPimComponentCRPHoldTime The holdtime of the component when it is a candidate RP in the local domain. The value of 0 is used to indicate that the local system is not a Candidate-RP.	secondsUnsigned32r/w Constraints: range: 0-255	.1.3.6.1.4.1.9.10.119.1.1.8.1.5
cPimComponentStatus The status of this entry. Creating the entry creates another protocol instance; destroying the entry disables a protocol instance.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.10.119.1.1.8.1.6