CISCO-DOCS-EXT-MIB Table View

For each upstream interface, this table maintains a number 
of objects related to Quality of Service scheduler which uses
these attributes to control cable modem registration.

cdxQosCtrlUpEntry row .1.3.6.1.4.1.9.9.116.1.1.1.1

A list of attributes for each upstream MAC scheduler
that supports Quality of Service. Entries in this table
exist for each ifEntry with ifType of docsCableUpstream(129).

Indexes

IF-MIBifIndex

Column	Syntax	OID
cdxQosCtrlUpAdmissionCtrl The admission control status for minimum guaranteed upstream bandwidth scheduling service requests for this upstream. When this object is set to 'true', if there is a new modem with minimum guaranteed u…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.116.1.1.1.1.1
cdxQosCtrlUpMaxRsvdBWPercent The percentage of upstream maximum reserved bandwidth to the raw bandwidth if the admission control is enabled on this upstream. For example, if the upstream interface has raw bandwidth 1,600,000 bits…	percentInteger32r/w Constraints: range: 10-1000	.1.3.6.1.4.1.9.9.116.1.1.1.1.2
cdxQosCtrlUpAdmissionRejects The count of cable modem registration requests rejected on this upstream interface due to insufficient reserved bandwidth for serving the cable modems with Unsolicited Grant Service (UGS) scheduling service when UGS …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.1.1.1.3
cdxQosCtrlUpReservedBW The current total reserved bandwidth in bits per second of this upstream interface. It is the sum of all cable modems' minimum guaranteed bandwidth in bits per second currently supported on this upstream.	bits/secondInteger32 Constraints: range: 0-102400000	.1.3.6.1.4.1.9.9.116.1.1.1.1.4
cdxQosCtrlUpMaxVirtualBW The maximum virtual bandwidth capacity of this upstream interface if the admission control is enabled. It is the raw bandwidth in bits per second times the percentage. If the admission control is disabled, then this o…	bits/secondInteger32 Constraints: range: 0-102400000	.1.3.6.1.4.1.9.9.116.1.1.1.1.5

This table describes the attributes of rate limiting for 
schedulers in cable upstream and downstream interfaces that 
support Quality of Service.  The rate limiting process is 
to ensure the Quality of Service and fairness.

cdxQosIfRateLimitEntry row .1.3.6.1.4.1.9.9.116.1.1.2.1

List of the rate limiting attributes for cable upstream and
downstream interfaces schedulers that support Quality of
Service. Entries in this table exist for each ifEntry with
ifType of docsCableUpstream(129) and doc…

Indexes

IF-MIBifIndex

Column	Syntax	OID
cdxQosIfRateLimitAlgm To ensure fairness, the CMTS will throttle the rate for bandwidth request (upstream)/packet sent (downstream) at which CMTS issues grants(upstream) or allow packet to be send(downstream) such that the flow never gets…	Enumerationr/w Enumerated Values: 1 noRateLimit 2 oneSecBurst 3 carLike 4 wtExPacketDiscard 5 shaping	.1.3.6.1.4.1.9.9.116.1.1.2.1.1
cdxQosIfRateLimitExpWt Weight for exponential moving average of loss rate for weighted excess packet discard algorithm to maintain. The higher value of the weight makes the algorithm more sensitive to the recent bandwidth usage by the Sid. …	Integer32r/w Constraints: range: 1-4	.1.3.6.1.4.1.9.9.116.1.1.2.1.2
cdxQosIfRateLimitShpMaxDelay The maximum shaping delay in milliseconds. That is, the maximum amount time of buffering the CMTS will allow for any rate exceeded flow. If the max buffering delay is large, the grants/packets of the flow will be bu…	Enumerationr/w Enumerated Values: 1 na 2 msec128 3 msec256 4 msec512 5 msec1024	.1.3.6.1.4.1.9.9.116.1.1.2.1.3
cdxQosIfRateLimitShpGranularity The width in milliseconds of each element in shaping delay queue, that is, the shaping granularity. The shaping granularity is only applied to rate limit algorithm: Token bucket algorithm with shaping. I…	Enumerationr/w Enumerated Values: 1 na 2 msec1 3 msec2 4 msec4 5 msec8 6 msec16	.1.3.6.1.4.1.9.9.116.1.1.2.1.4

The list contains the additional attributes of a single Service
ID that provided by docsIfCmtsServiceEntry.

cdxCmtsServiceExtEntry row .1.3.6.1.4.1.9.9.116.1.1.3.1

Additional objects for docsIfCmtsServiceTable entry including
downstream traffic statistics and excess counts against the
Quality of Service limits for each Service ID.
From DOCSIS 1.1 onwards statistics are maintaine…

Indexes

No indexes recorded

Column	Syntax	OID
cdxIfCmtsServiceOutOctets The cumulative number of Packet Data octets sent for this Service ID.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.1.3.1.1
cdxIfCmtsServiceOutPackets The cumulative number of Packet data packets sent for this Service ID.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.1.3.1.2
cdxQosMaxUpBWExcessRequests The number of upstream bandwidth requests which exceeds the maximum upstream bandwidth allowed for a service defined in the Quality of Service profile associated with this Sid. The request which exceeds the maximum up…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.1.3.1.3
cdxQosMaxDownBWExcessPackets The number of downstream bandwidth packets which exceeds the maximum downstream bandwidth allowed for a service defined in the Quality of Service profile associated with this Sid. The packet which exceeds the maximum d…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.1.3.1.4
cdxIfCmtsServiceHCInOctets The cumulative number of Packet Data octets received on this Service ID. The count does not include the size of the Cable MAC header. This object is a 64-bit version of docsIfCmtsServiceInOctets.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.116.1.1.3.1.5
cdxIfCmtsServiceHCInPackets The cumulative number of Packet Data packets received on this Service ID. This object is a 64-bit version of docsIfCmtsServiceInPackets.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.116.1.1.3.1.6
cdxIfCmtsServiceHCOutOctets The cumulative number of Packet Data octets sent for this Service ID. This object is a 64-bit version of cdxIfCmtsServiceOutOctets.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.116.1.1.3.1.7
cdxIfCmtsServiceHCOutPackets The cumulative number of Packet Data packets sent for this Service ID. This object is a 64-bit version of cdxIfCmtsServiceOutPackets.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.116.1.1.3.1.8

The table contains the attributes of a particular 
Information Element type for each instance of the MAC 
scheduler. It is indexed by upstream ifIndex. An Entry
exists for each ifEntry with ifType of docsCableUpstream(129)
Since each upstream has an instance of a MAC Scheduler so 
this table has the per MAC scheduler slot information on a
per Information Element basis.

cdxUpInfoElemStatsEntry row .1.3.6.1.4.1.9.9.116.1.1.4.1

The list of statistics for a type of Information Element(IE)
which defines the allowed usage for a range of upstream mini
slots. One entry exists for each Information Element (IE) in
a upstream which ifType is docsCable…

Indexes

IF-MIBifIndex cdxUpInfoElemStatsNameCode

Column	Syntax	OID
cdxUpInfoElemStatsNameCode This entry describes the Information Element (IE) type. Enumerations are : reqIE(1) : Request Information Element, The request Information Element provides an upstream in…	Enumeration Enumerated Values: 1 reqIE 2 reqOrDataIE 3 initMtnIE 4 stnMtnIE 5 shortGrantIE 6 longGrantIE	.1.3.6.1.4.1.9.9.116.1.1.4.1.1
cdxUpInfoElemStatsIEType The current number of mini-slots used for the Information Element type. The value is only a snapshot since the current number of mini-slots of this IE type could be changing rapidly.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.9.116.1.1.4.1.2

This table describes the attributes of queues  
in cable interfaces schedulers that support 
Quality of Service.

cdxBWQueueEntry row .1.3.6.1.4.1.9.9.116.1.2.1.1

The list of queue attributes in cable upstream and downstream
interfaces schedulers that supports Quality of Service.
Entries in this table exist for each ifEntry with ifType of
docsCableUpstream(129) and docsCableDow…

Indexes

IF-MIBifIndex cdxBWQueueNameCode

Column	Syntax	OID
cdxBWQueueNameCode The name code for the queue. cirQ :CIR queue. The queue is for Committed Information Rate (CIR) type of service which serves Service IDs which have minimum guaranteed rate in its QoS profile.…	Enumeration Enumerated Values: 1 cirQ 2 tbeQ 3 p0BEGrantQ 4 p1BEGrantQ 5 p2BEGrantQ 6 p3BEGrantQ 7 p4BEGrantQ 8 p5BEGrantQ 9 p6BEGrantQ 10 p7BEGrantQ 11 rngPollQ	.1.3.6.1.4.1.9.9.116.1.2.1.1.1
cdxBWQueueOrder The relative order of this queue to the other queues within the cable interface. The smaller number has higher order. That is, 0 is the highest order and 10 is the lowest order. The scheduler will serve the requests …	Integer32 Constraints: range: 0-10	.1.3.6.1.4.1.9.9.116.1.2.1.1.2
cdxBWQueueNumServedBeforeYield The maximum number of requests/packets the scheduler can serve before yielding to another queue. The value 0 means all requests must be served before yielding to another queue. The range is 0-50 for DOCSIS 1.0 and fo…	Integer32 Constraints: range: 0-64	.1.3.6.1.4.1.9.9.116.1.2.1.1.3
cdxBWQueueType The queuing type which decides the position of a request/packet within the queue. unknown : queue type unknown. other : not fifo, and not priority. fifo : first in first out. priority: each bandwidth reque…	Enumeration Enumerated Values: 1 unknown 2 other 3 fifo 4 priority	.1.3.6.1.4.1.9.9.116.1.2.1.1.4
cdxBWQueueMaxDepth The maximum number of requests/packets which the queue can support.The range is 0-50 for DOCSIS1.0 and for DOCSIS1.1 it is 0-64.	Integer32 Constraints: range: 0-64	.1.3.6.1.4.1.9.9.116.1.2.1.1.5
cdxBWQueueDepth The current number of requests/packets in the queue. The range is 0-50 for DOCSIS1.0 and for DOCSIS1.1 it is 0-64.	Integer32 Constraints: range: 0-64	.1.3.6.1.4.1.9.9.116.1.2.1.1.6
cdxBWQueueDiscards The number of requests/packets discarded because of queue overflow (queue depth > queue maximum depth).	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.2.1.1.7

This table contains information about cable modems (CM) or 
Customer Premises Equipments (CPE).

cdxCmCpeEntry row .1.3.6.1.4.1.9.9.116.1.3.1.1

The list contains information for a cable modem (CM) or a
Customer Premises Equipment (CPE). An entry exist for
each cable modem supported by CMTS and each Customer Premises
Equipment connected to a cable modem suppor…

Indexes

cdxCmCpeMacAddress

Column	Syntax	OID
cdxCmCpeMacAddress The Mac address to identify a cable modem or a Customer Premises Equipment.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.116.1.3.1.1.1
cdxCmCpeType Indicate this entry is for cable modem or Customer Premises Equipment. The enumerations are: cm(1): cable modem cpe(2): Customer Premises Equipment	Enumeration Enumerated Values: 1 cm 2 cpe	.1.3.6.1.4.1.9.9.116.1.3.1.1.2
cdxCmCpeIpAddress Ip address of the cable modem or Customer Premises Equipment.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.9.9.116.1.3.1.1.3
cdxCmCpeIfIndex The CMTS cable MAC interface index (ifType of docsCableMaclayer(127)) that cable modem or Customer Premises Equipment connects to. Use cdxCmCpeIfIndex and cdxCmCpeCmtsServiceId to identify an entry i…	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.116.1.3.1.1.4
cdxCmCpeCmtsServiceId The cable modem's primary Service ID if the type is cm. The primary Service ID for the CM which the CPE connects if the type is cpe. Use cdxCmCpeIfIndex and cdxCmCpeCmtsServiceId to identify an entry i…	Integer32 Constraints: range: 1-16383	.1.3.6.1.4.1.9.9.116.1.3.1.1.5
cdxCmCpeCmStatusIndex Pointer to an entry in docsIfCmtsCmStatusTable identifying status of the CM (which the CPE connects to.)	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.116.1.3.1.1.6
cdxCmCpeAccessGroup ASCII text to identify the Access Group for a CM or CPE. Access Group is to filter the upstream traffic for that CM or CPE.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.9.9.116.1.3.1.1.7
cdxCmCpeResetNow Setting this object to true(1) causes the device to reset. Reading this object always returns false(2). For cdxCmCpeType value cm(1), CMTS removes the CM from the Station Maintenance List and would ca…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.116.1.3.1.1.8
cdxCmCpeDeleteNow Setting this object to true(1) causes the CM/CPE to be deleted. Reading this object always returns false(2). For cdxCmCpeType value cm(1), CMTS delete CM from its interface. For cdxCmCpe…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.116.1.3.1.1.9

The list contains the additional CM status information.

cdxCmtsCmStatusExtEntry row .1.3.6.1.4.1.9.9.116.1.3.2.1

Additional objects for docsIfCmtsCmStatusTable entry.

Indexes

No indexes recorded

Column	Syntax	OID
cdxCmtsCmStatusValue Current Cable Modem connectivity state. The object extends states in docsIfCmtsCmStatusValue in more details. The enumerations are: offline(1) : modem considered offline. others(2) …	Enumeration Enumerated Values: 1 offline 2 others 3 initRangingRcvd 4 initDhcpReqRcvd 5 onlineNetAccessDisabled 6 onlineKekAssigned 7 onlineTekAssigned 8 rejectBadMic 9 rejectBadCos 10 kekRejected 11 tekRejected 12 online 13 initTftpPacketRcvd 14 initTodRequestRcvd 15 reset 16 rangingInProgress 17 rangingCompleted 18 dhcpGotIpAddr 19 rejStaleConfig 20 rejIpSpoof 21 rejClassFail 22 rejRegNack 23 bpiKekExpired 24 bpiTekExpired 25 shutdown 26 channelChgInitRangingRcvd 27 channelChgRangingInProgress	.1.3.6.1.4.1.9.9.116.1.3.2.1.1
cdxIfCmtsCmStatusOnlineTimes The number of times that the modem changes the connectivity state from 'offline' to 'online' over the time period from the modem's first ranging message received by CMTS until now. The modem is conside…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.3.2.1.2
cdxIfCmtsCmStatusPercentOnline The percentage of time that the modem stays 'online' over the time period from the modem's first ranging message received by CMTS until now. The value for this object is 100 times bigger than the real …	Integer32 Constraints: range: 0-10000	.1.3.6.1.4.1.9.9.116.1.3.2.1.3
cdxIfCmtsCmStatusMinOnlineTime The minimum period of time the modem stayed 'online' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmt…	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.9.9.116.1.3.2.1.4
cdxIfCmtsCmStatusAvgOnlineTime The average period of time the modem stayed 'online' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmt…	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.9.9.116.1.3.2.1.5
cdxIfCmtsCmStatusMaxOnlineTime The maximum period of time the modem stayed 'online' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmt…	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.9.9.116.1.3.2.1.6
cdxIfCmtsCmStatusMinOfflineTime The minimum period of time modem stayed 'offline' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCmtsCm…	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.9.9.116.1.3.2.1.7
cdxIfCmtsCmStatusAvgOfflineTime The average period of time the modem stayed 'offline' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCm…	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.9.9.116.1.3.2.1.8
cdxIfCmtsCmStatusMaxOfflineTime The maximum period of time the modem stayed 'offline' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered as 'online' when the value for cdxCm…	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.9.9.116.1.3.2.1.9
cdxIfCmtsCmStatusDynSidCount The number of active dynamic SIDs on this modem. Prior to getting the assigned the Service Flow IDs(SFID) the CM must must complete a number of protocol transactions. The CMTS assigns a temporary Service ID (SID) to co…	Integer32 Constraints: range: 0-16383	.1.3.6.1.4.1.9.9.116.1.3.2.1.10
cdxIfCmtsCmStatusAddlInfo This object indicates additional attributes regarding the CM. 1. noisyPlant indicates that the CM connection is noisy. 2. modemPowerMaxOut indicates that the modem has reached its maximum power level. A b…	Bits Enumerated Values: 0 noisyPlant 1 modemPowerMaxOut	.1.3.6.1.4.1.9.9.116.1.3.2.1.11
cdxIfCmtsCmStatusOnlineTimesNum The number of times that the modem changes the connectivity state from 'offline' to 'online' over the time period from the modem's first ranging message received by CMTS until now. The modem is considered…	CdxResettableCounter32	.1.3.6.1.4.1.9.9.116.1.3.2.1.12
cdxIfCmtsCmStatusLastResetTime The last cable modem connectivity statistics reset time. If the value of this object is '0', then the cable modem connectivity statistics had not been reset.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.116.1.3.2.1.13

This table contains the additions attributes of a CMTS MAC
interface that provided by docsIfCmtsMacTable.

cdxCmtsMacExtEntry row .1.3.6.1.4.1.9.9.116.1.3.3.1

Additional objects for docsIfCmtsMacTable entry including
the cable modem notification enable/disable and the interval
of cable modem notification sent by the CMTS for a cable modem
that the Mac interface supports. An …

Indexes

No indexes recorded

Column	Syntax	OID
cdxCmtsCmOnOffTrapEnable An indication of whether the cdxCmtsCmOnOffNotification is enabled. The default value is false(2).	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.116.1.3.3.1.1
cdxCmtsCmOnOffTrapInterval The interval for cdxCmtsCmOnOffNotification sent by CMTS for one online/offline state change if cdxCmtsCmOnOffTrapEnable is true. If there are more than one state changes to online/offline for a cable …	secondsInteger32r/w Constraints: range: 0-86400	.1.3.6.1.4.1.9.9.116.1.3.3.1.2
cdxCmtsCmDefaultMaxCpes The default maximum number of permitted CPEs per modem in this cable interface. A modem can override this value by setting the object cdxCmtsCmMaxCpeNumber in the cdxCmtsCmTable. The value -1 means th…	Integer32r/w Constraints: range: -1-255	.1.3.6.1.4.1.9.9.116.1.3.3.1.3
cdxCmtsCmTotal The total count of cable modems on this cable mac interface since boot.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.116.1.3.3.1.4
cdxCmtsCmActive The count of cable modems that are active. Active cable modems are recognized by the cdxCmtsCmStatusValue other than offline(1).	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.116.1.3.3.1.5
cdxCmtsCmRegistered The count of cable modems that are registered and online on this cable mac interface. Registered cable modems are those with one of the following values. registrationComplete(6) of docsIfCmtsCmStatusValue OR either …	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.116.1.3.3.1.6
cdxCmtsCmDMICMode The Dynamic Shared Secret feature can operate in three different modes, depending on what action should be taken for cable modems that fail the CMTS MIC verification check: notConfigured(1): It indicates that the DMIC…	Enumerationr/w Enumerated Values: 1 notConfigured 2 mark 3 lock 4 reject	.1.3.6.1.4.1.9.9.116.1.3.3.1.7
cdxCmtsCmDMICLockQos If cdxCmtsCmDMICMode is set to lockingMode(3), this object would contain the restrictive QoS profile number as indicated by docsIfQosProfIndex if set and it will have 0 if not applicable or not defined. In case, cdxCm…	Integer32r/w Constraints: range: 1-16383	.1.3.6.1.4.1.9.9.116.1.3.3.1.8

A table of CMTS operation entries to instruct cable modems
to move to a new downstream and/or upstream channel. 
          
An entry in this table is an operation that has been 
initiated from CMTS to generates downstream frequency and/or 
upstream channel override fields in the RNG-RSP message sent 
to a cable modem.  A RNG-RSP message is sent to a cable 
modem during initial maintenance opportunity. 
          
This operation causes the uBR to place an entry for the cable 
modem specified into the override request queue.  The link is 
then broken by deleting the modem from its polling list.  When 
the modem attempts initial ranging, the override request 
causes downstream frequency and upstream channel override 
fields to be inserted into the RNG-RSP message.

cdxCmtsCmChOverEntry row .1.3.6.1.4.1.9.9.116.1.3.5.1

A CMTS operation entry to instruct a cable modem to move to
a new downstream and/or upstream channel.

A CMTS operator can use this to initiate an operation
in CMTS to instruct a cable modem to move to a new…

Indexes

cdxCmtsCmChOverSerialNumber

Column	Syntax	OID
cdxCmtsCmChOverSerialNumber Object which specifies a unique entry in the table. A management station wishing to initiate a channel override operation should use a pseudo-random value for this object when creating or modifying an instance of a cd…	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.116.1.3.5.1.1
cdxCmtsCmChOverMacAddress The mac address of the cable modem that the CMTS instructs to move to a new downstream and/or upstream channel. This column must be set to a valid Mac address currently in the CMTS in order for this ent…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.116.1.3.5.1.2
cdxCmtsCmChOverDownFrequency The new downstream frequency which the cable modem is instructed to move to. The value 0 is to ask the CMTS not to override the downstream frequency.	hertzInteger32r/w Constraints: range: 0-1000000000	.1.3.6.1.4.1.9.9.116.1.3.5.1.3
cdxCmtsCmChOverUpChannelId The new channel Id which the cable modem is instructed to move to. The value -1 is to ask the CMTS not to override the upstream channel Id.	Integer32r/w Constraints: range: -1-255	.1.3.6.1.4.1.9.9.116.1.3.5.1.4
cdxCmtsCmChOverTrapOnCompletion Specifies whether or not a cdxCmtsCmChOverNotification should be issued on completion of the operation. If such a notification is desired, it is the responsibility of the management entity to ensure that the SNMP ad…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.116.1.3.5.1.5
cdxCmtsCmChOverOpInitiatedTime The value of sysUpTime at which the operation was initiated. Since it is possible to have more than one entry in this table for a cable modem, this object can help to distinguish the entries for the same cable modem.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.116.1.3.5.1.6
cdxCmtsCmChOverState The status of the specified channel override operation. The enumerations are: messageSent(1): the CMTS has sent a RNG-RSP message with channel override to the cable modem. commandNotActive(2): the co…	Enumeration Enumerated Values: 1 messageSent 2 commandNotActive 3 noOpNeeded 4 modemNotFound 5 waitToSendMessage 6 timeOut	.1.3.6.1.4.1.9.9.116.1.3.5.1.7
cdxCmtsCmChOverRowStatus The status of this table entry. This value for cdxCmtsCmChOverMacAddress must be valid Mac address currently in the CMTS in order for the row status to be set to active successfully. …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.116.1.3.5.1.8

This table contains attributes or configurable parameters 
for cable modems from a CMTS.

cdxCmtsCmEntry row .1.3.6.1.4.1.9.9.116.1.3.6.1

The list contains a cable modem's attributes or
configurable parameters from a CMTS.

Indexes

DOCS-IF-MIBdocsIfCmtsCmStatusIndex

Column	Syntax	OID
cdxCmtsCmMaxCpeNumber The maximum number of permitted CPEs connecting to the modem. The value -1 means to use the default value of maximum hosts per modem in the CMTS cable interface which the modem connects to and the valu…	Integer32r/w Constraints: range: -1-255	.1.3.6.1.4.1.9.9.116.1.3.6.1.1
cdxCmtsCmCurrCpeNumber The current number of CPEs connecting to the modem. The value 0 means no hosts connecting to the modem.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.9.9.116.1.3.6.1.2
cdxCmtsCmQosProfile The index in docsIfQosProfileTable describing the quality of service attributes associated with this particular modem's primary SID. When trying to change the value, if the new value is not a valid inde…	Integer32r/w Constraints: range: 0-16383	.1.3.6.1.4.1.9.9.116.1.3.6.1.3

This table contains the list of modems which failed the CMTS
Dynamic Message Integrity Check (DMIC). The modems are 
either
Marked: The modems failed the DMIC check but were still 
        allowed to come online.
Locked: The modems failed the DMIC check and hence were 
        allowed to come online with a restrictive QoS 
        profile as defined in  cdxCmtsCmDMICLockQos.
Rejected: The modems failed the DMIC check and hence
          were not allowed to come online.
Another objective of the objects in this table is to clear
the lock on the modems.

cdxCmtsCmStatusDMICEntry row .1.3.6.1.4.1.9.9.116.1.3.7.1

Additional DMIC objects for docsIfCmtsCmStatusTable
entry.

Indexes

DOCS-IF-MIBdocsIfCmtsCmStatusIndex

Column	Syntax	OID
cdxCmtsCmStatusDMICMode This shows all the cable modems that are online or offline and that had failed the Dynamic CMTS MIC verification check. The state is mentioned as follows: mark(1): The modem was allowed to come online. lock(2): The mode…	Enumeration Enumerated Values: 1 mark 2 lock 3 reject	.1.3.6.1.4.1.9.9.116.1.3.7.1.1
cdxCmtsCmStatusDMICUnLock When set to TRUE, it forces the cable modems to reinitialize, and the cable modems must re-register with a valid DOCSIS configuration file before being allowed online. Otherwise, the cable modem is locked in its curre…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.116.1.3.7.1.2

This table contains information about CPE connects behind
cable modem. It will return IP address and IP address type
of each CPE connect to a CM.
          
It is not intended to walk the whole table. An application
would need to query this table based on the specific indices.
Otherwise, it will impact the CMTS performance due to the 
huge size of this table.
          
The agent creates/destroys/modifies an entry whenever there
is a CPE connect to a cable modem or disconnect from a cable
modem.

cdxCmToCpeEntry row .1.3.6.1.4.1.9.9.116.1.3.8.1

Represents an entry in the table. Each entry is created if
there is CPE connects to a cable modem.

The indices uniquely identify a CPE. It is never the intent
for an application to perform a SNMP Get operat…

Indexes

cdxCmToCpeCmMacAddress cdxCmToCpeInetAddressType cdxCmToCpeInetAddress

Column	Syntax	OID
cdxCmToCpeCmMacAddress The MAC address that uniquely identifies a cable modem that CPEs connects to.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.116.1.3.8.1.1
cdxCmToCpeInetAddressType The type of Internet address of the cdxCmToCpeInetAddress.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.116.1.3.8.1.2
cdxCmToCpeInetAddress This object identifies the address assigned to this CPE.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.116.1.3.8.1.3

This table contains information about cable modems with CPE
connects to.
          
It is not intended to walk the whole table. An application
would need to query this table base on the specific index.
Otherwise, it will impact the CMTS performance due to the
huge size of this table.
          
The agent creates/destroys/modifies an entry whenever there
is update for the cable modem that CPE connects to.

cdxCpeToCmEntry row .1.3.6.1.4.1.9.9.116.1.3.9.1

An entry in cdxCpeToCmTable. Each entry contains information
on the MAC address, IP Address, and status index for the
cable modem with a specific CPE connects to. Each entry is
created if there is any cable modem with …

Indexes

cdxCpeToCmCpeMacAddress

Column	Syntax	OID
cdxCpeToCmCpeMacAddress This object identifies the MAC address of the CPE.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.116.1.3.9.1.1
cdxCpeToCmMacAddress This object identifies the MAC address of the cable modem.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.116.1.3.9.1.2
cdxCpeToCmInetAddressType The type of Internet address of the cdxCpeToCmInetAddress object.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.116.1.3.9.1.3
cdxCpeToCmInetAddress This object identifies the address assigned to this cable modem.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.116.1.3.9.1.4
cdxCpeToCmStatusIndex An entry in docsIfCmtsCmStatusTable identifying status index of the cable modem which the CPE connects to.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.116.1.3.9.1.5

The table contains a list CPE's IP Prefix management
information.

cdxCpeIpPrefixEntry row .1.3.6.1.4.1.9.9.116.1.3.10.1

An entry contains information of CM's MAC,
CPE's IP prefix type, CPE's IP prefix address,
CPE's IP prefix length and CPE's MAC address.
An entry is created if CPE is associated with a prefix.

Indexes

cdxCpeIpPrefixCmMacAddress cdxCpeIpPrefixType cdxCpeIpPrefixAddress cdxCpeIpPrefixLen

Column	Syntax	OID
cdxCpeIpPrefixCmMacAddress This object indicates the MAC address of the cable modem.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.116.1.3.10.1.1
cdxCpeIpPrefixType This object indicates the IP prefix type of the CPE. This is the type of cdxCpeIpPrefixAddress object.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.116.1.3.10.1.2
cdxCpeIpPrefixAddress This object indicates the IP prefix address. The type of this address is determined by the value of cdxCpeIpPrefixType object.	OctetString Constraints: range: 1-96	.1.3.6.1.4.1.9.9.116.1.3.10.1.3
cdxCpeIpPrefixLen This object indicates the IP prefix length of the CPE. This is the length of cdxCpeIpPrefixAddress object.	INET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.9.9.116.1.3.10.1.4
cdxCpeIpPrefixCpeMacAddress This object indicates the MAC address of CPE.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.116.1.3.10.1.5
cdxCpeIpPrefixCpeType This object indicates the type of CPE. Device Type: B - CM Bridge, R - CM Router IP Assignment Method: D - DHCP the format looks like 'R/D'.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.116.1.3.10.1.6

This table contains upstream channel attributes for  
automated Spectrum management, in addition to the ones
provided by docsIfUpstreamChannelEntry.
It also contains upstream channel attributes to count 
the number of active,registered and total number of cable 
modems on this upstream.

cdxIfUpstreamChannelExtEntry row .1.3.6.1.4.1.9.9.116.1.4.1.1

Additional objects for docsIfUpstreamChannelEntry,including
the secondary upstream channel modulation profile,the
lower bound for the channel width and the number of active,
registered and total number of cable modems…

Indexes

No indexes recorded

Column	Syntax	OID
cdxIfUpChannelWidth The lower bound for the bandwidth of this upstream channel. The bandwidth specified by docsIfUpChannelWidth is used as the upper bound of the upstream channel. The two objects, docsIfUpChannelWidth and cdxIfUpChannelWi…	hertzInteger32r/w Constraints: range: 0-16000000	.1.3.6.1.4.1.9.9.116.1.4.1.1.1
cdxIfUpChannelModulationProfile The secondary modulation profile for the upstream channel. This should be a QPSK modulation profile if the primary profile is QAM-16. The CMTS will switch from primary profile (QAM16) to secondary profile (QPSK) depen…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.4.1.1.2
cdxIfUpChannelCmTotal The total count of cable modems on this upstream channel since boot.	Integer32 Constraints: range: 0-8191	.1.3.6.1.4.1.9.9.116.1.4.1.1.3
cdxIfUpChannelCmActive The count of cable modems that are active.Active cable modems are recognized by the cdxCmtsCmStatusValue other than offline(1).	Integer32 Constraints: range: 0-8191	.1.3.6.1.4.1.9.9.116.1.4.1.1.4
cdxIfUpChannelCmRegistered The count of cable modems that are registered and online on this upstream. Registered cable modems are those with one of the following values: registrationComplete(6) of docsIfCmtsCmStatusValue OR online(12), kekRejecte…	Integer32 Constraints: range: 0-8191	.1.3.6.1.4.1.9.9.116.1.4.1.1.5
cdxIfUpChannelInputPowerLevel The Upstream Input power level at the CMTS interface. This is the expected power level and is different from the actual power received. If not configured the default value is 0 dBmV and is also the optimum setting power…	Integer32r/w Constraints: range: -100-250	.1.3.6.1.4.1.9.9.116.1.4.1.1.6
cdxIfUpChannelAvgUtil The average percentage of upstream channel utilization. This item indicates the running average of percent channel utilization in CMTS upstream Mac scheduler.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.9.9.116.1.4.1.1.7
cdxIfUpChannelAvgContSlots The average percentage of contention mini-slots. This item indicates the running average of percent contention mini-slots in CMTS upstream Mac scheduler.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.9.9.116.1.4.1.1.8
cdxIfUpChannelRangeSlots The average percentage of initial ranging mini-slots. This item indicates the running average of percent initial ranging mini-slots in CMTS upstream Mac scheduler.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.9.9.116.1.4.1.1.9
cdxIfUpChannelNumActiveUGS This object indicates the number of active Unsolicited Grant Service (UGS) on a given upstream. This would be used for the user to evaluate traffic load at any given time of the day. The Unsolicited Gra…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.4.1.1.10
cdxIfUpChannelMaxUGSLastOneHour This object indicates the maximum number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last one hour. This would be used for the user to evaluate traffic load at any given time of the day. …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.4.1.1.11
cdxIfUpChannelMinUGSLastOneHour This object indicates the minimum number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last one hour. This would be used for the user to evaluate traffic load at any given time of the day. …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.4.1.1.12
cdxIfUpChannelAvgUGSLastOneHour This object indicates the average number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last one hour. This would be used for the user to evaluate traffic load at any given time of the day. …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.4.1.1.13
cdxIfUpChannelMaxUGSLastFiveMins This object indicates the maximum number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last five minutes. This would be used for the user to evaluate traffic load at any given time of the day…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.4.1.1.14
cdxIfUpChannelMinUGSLastFiveMins This object indicates the minimum number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last five minutes. This would be used for the user to evaluate traffic load at any given time of the day…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.4.1.1.15
cdxIfUpChannelAvgUGSLastFiveMins This object indicates the average number of Unsolicited Grant Service (UGS) allocated on a given upstream in the last five minutes. This would be used for the user to evaluate traffic load at any given time of the day…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.4.1.1.16

This table contains information regarding the channel list in the CMTS
assigned bonding group a cable modem is assigned to use.
When a modem is operating in partial service this table will contain
additional information about that cable modem indicating which channels
are impaired and contributing to partial service.

cdxWBResilCmEntry row .1.3.6.1.4.1.9.9.116.1.5.13.1

The list contains information for a cable modem(CM).

Provided the following information for a cable modem:
How many downstream channels in total;
How many upstream channels in total;
How many active downstr…

Indexes

cdxWBResilCmIndex

Column	Syntax	OID
cdxWBResilCmIndex This attribute uniquely identifies a CM. The CMTS must assign a single id value for each CM MAC address seen by the CMTS. The CMTS should ensure that the association between an Id and MAC Address remains constant duri…	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.4.1.9.9.116.1.5.13.1.1
cdxWBResilCmMacAddr This attribute represents the MAC address of the CM. If the CM has multiple MAC addresses, this is the MAC address associated with the MAC Domain interface.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.116.1.5.13.1.2
cdxWBResilCmTotalDsNum Total downstream channel number of the CM.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.5.13.1.3
cdxWBResilCmTotalUsNum Total upstream channel number of the CM.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.5.13.1.4
cdxWBResilCmCurrentDsNum Current active downstream channel number, it's the total downstream channel minus downstream partial service channel number.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.5.13.1.5
cdxWBResilCmCurrentUsNum Current active upstream channel number, it's the total upstream channel minus upstream partial service channel number.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.5.13.1.6
cdxWBResilCmImpairedDsChIndex Impaired downstream channel index list. The index in list is rf channel ifIndex. If there's no downstream channel impaired, return empty. The output looks like: '137000 137001 137002'. This value appears only in a cable…	SNMP-TARGET-MIBSnmpTagList Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.116.1.5.13.1.7
cdxWBResilCmImpairedUsChIndex Impaired upstream channel index list. The index in list is upstream channel ifIndex. If there's no upstream channel impaired, return empty. The output looks like: '196408 196409 196410'. This value appears only in a cab…	SNMP-TARGET-MIBSnmpTagList Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.116.1.5.13.1.8

This table contains information of the mapping of
the physical RF channels to the primary RF channels.

cdxRFtoPrimaryChannelMappingEntry row .1.3.6.1.4.1.9.9.116.1.6.1.1

An Entry provides the association between the physical
RF channels and the primary RF Channels.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cdxPrimaryChannelIfIndex The ifIndex of the primary channel interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.116.1.6.1.1.1

This table contains information of the mapping of
the primary RF channels to the physical RF channels.

cdxPrimaryChanneltoRFMappingEntry row .1.3.6.1.4.1.9.9.116.1.6.2.1

An Entry provides the association between the primary
RF channels and the physical RF Channels.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cdxPhysicalRFIfIndex The ifIndex of the physical RF channel interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.116.1.6.2.1.1

This table contains CM management information of Transmit
Channel Set(TCS) in the system.

cdxCmtsMtcCmEntry row .1.3.6.1.4.1.9.9.116.1.7.1.1

An entry provides the CM statistics and management
information of a specific TCS. The interface populated in this
table is of ifType = docsCableMaclayer(127).

Indexes

IF-MIBifIndex cdxCmtsMtcTcsId

Column	Syntax	OID
cdxCmtsMtcTcsId This object indicates the Id of the Transmit Channel Set.	DOCS-IF3-MIBChSetId	.1.3.6.1.4.1.9.9.116.1.7.1.1.1
cdxCmtsMtcCmTotal This object indicates the total number of cable modems which use this TCS in the MAC domain.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.1.1.2
cdxCMtsMtcCmOperational This object indicates the number of operational cable modems which uses this TCS in the MAC domain.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.1.1.3
cdxCmtsMtcCmRegistered This object indicates the number of registered cable modems which use this TCS in the MAC domain.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.1.1.4
cdxCmtsMtcCmUnregistered This object indicates the number of unregistered cable modem which use this TCS in the MAC domain.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.1.1.5
cdxCmtsMtcCmOffline This object indicates the number of offline cable modems which uses this TCS in the MAC domain.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.1.1.6
cdxCmtsMtcCmWideband This object indicates the number of operational cable modems which are in wideband state and use this TCS in the MAC domain.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.1.1.7
cdxCmtsMtcUpstreamBondGrp This object specifies the upstream channel bonding group.	CdxUpstreamBondGrpList Type Constraints: range: 0..320	.1.3.6.1.4.1.9.9.116.1.7.1.1.8

This table contains the Upstream Channel Bonding
Service Flow management information.

cdxCmtsUscbSflowEntry row .1.3.6.1.4.1.9.9.116.1.7.2.1

A entry contains the Service Flow statistics for a specific
Upstream Channel Bonding group. The interface populated in this
table is of ifType = docsCableMaclayer(127).

Indexes

IF-MIBifIndex cdxCmtsUsBondingGrpId

Column	Syntax	OID
cdxCmtsUsBondingGrpId This object indicates upstream bonding group identifier within the MAC Domain.	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.1
cdxCmtsUscbSfTotal This object indicates the total number of service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.2
cdxCmtsUscbSfPri This object indicates the total number of primary service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.3
cdxCmtsUscbStaticSfBe This object indicates the number of static BE service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.4
cdxCmtsUscbStaticSfUgs This object indicates the number of static UGS service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.5
cdxCmtsUscbStaticSfUgsad This object indicates the number of static UGS-AD service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.6
cdxCmtsUscbStaticSfRtps This object indicates the number of static RTPS service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.7
cdxCmtsUscbStaticSfNrtps This object indicates the number of static NRTPS service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.8
cdxCmtsUscbDynSfBe This object indicates the number of dynamic BE service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.9
cdxCmtsUscbDynSfUgs This object indicates the number of dynamic UGS service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.10
cdxCmtsUscbDynSfUgsad This object indicates the number of dynamic UGS-Ad service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.11
cdxCmtsUscbDynSfRtps This object indicates the number of dynamic RTPS service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.12
cdxCmtsUscbDynSfNrtps This object indicates the number of dynamic NRTPS service flows which use this upstream channel bonding group.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.116.1.7.2.1.13
cdxCmtsUscbDescr This object indicates the description of upstream channel bonding group.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.116.1.7.2.1.14

The cdxRPDGS7KTable contains the attributes of GS7K. 
An Entry exists for each instance. 
It is indexed by GS7K's MacAddress.

cdxRPDGS7KEntry row .1.3.6.1.4.1.9.9.116.1.9.1.1

The list of statistics for all the sensor,
such as volatage, the state of TriSwitch.

Indexes

cdxRPDGS7KMacAddress

Column	Syntax	OID
cdxRPDGS7KMacAddress This is MacAddress of RPDGS7K which is used for index	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.116.1.9.1.1.1
cdxRPDGS7KPS1p24v This is the Object of RPDGS7KPS1p24v	0.01VDCInteger32 Constraints: range: 0-3000	.1.3.6.1.4.1.9.9.116.1.9.1.1.2
cdxRPDGS7KPS1p8v This is the Object of RPDGS7KPS1p8v	0.01VDCInteger32 Constraints: range: 0-1000	.1.3.6.1.4.1.9.9.116.1.9.1.1.3
cdxRPDGS7KPS1p5v This is the Object of RPDGS7KPS1p5v	0.01VDCInteger32 Constraints: range: 0-625	.1.3.6.1.4.1.9.9.116.1.9.1.1.4
cdxRPDGS7KPS1n6v This is the Object of RPDGS7KPS1n6v	0.01VDCInteger32 Constraints: range: 0-800	.1.3.6.1.4.1.9.9.116.1.9.1.1.5
cdxRPDGS7KPS1AC This is the Object of RPDGS7KPS1AC	0.1VACInteger32 Constraints: range: 300-2000	.1.3.6.1.4.1.9.9.116.1.9.1.1.6
cdxRPDGS7KPS2p24v RPDGS7KPS2p24v	0.01VDCInteger32 Constraints: range: 0-3000	.1.3.6.1.4.1.9.9.116.1.9.1.1.7
cdxRPDGS7KPS2p8v This is the Object of RPDGS7KPS2p8v	0.01VDCInteger32 Constraints: range: 0-1000	.1.3.6.1.4.1.9.9.116.1.9.1.1.8
cdxRPDGS7KPS2p5v This is the Object of RPDGS7KPS2p5v	0.01VDCInteger32 Constraints: range: 0-625	.1.3.6.1.4.1.9.9.116.1.9.1.1.9
cdxRPDGS7KPS2n6v This is the Object of RPDGS7KPS2n6v	0.01VDCInteger32 Constraints: range: 0-800	.1.3.6.1.4.1.9.9.116.1.9.1.1.10
cdxRPDGS7KPS2AC This is the Object of RPDGS7KPS2AC	0.1VACInteger32 Constraints: range: 300-2000	.1.3.6.1.4.1.9.9.116.1.9.1.1.11
cdxRPDGS7KTx1OptPower This is the Object of RPDGS7K Tx4 Opt Power	0.01mWInteger32 Constraints: range: 0-300	.1.3.6.1.4.1.9.9.116.1.9.1.1.12
cdxRPDGS7KRx1OptPower This is the Object of RPDGS7K Rx4 Opt Power	0.01mWInteger32 Constraints: range: 0-300	.1.3.6.1.4.1.9.9.116.1.9.1.1.13
cdxRPDGS7KTriSwitch This is the Object of RPDGS7K TriSwitch, The relationship which the number indicates is low(1) for -6dB high(2) for 0dB pad(3) for off	Enumerationr/w Enumerated Values: 1 low 2 high 3 pad	.1.3.6.1.4.1.9.9.116.1.9.1.1.14
cdxRPDGS7KTamp This is the Object of RPDGS7K Tamp	Enumeration Enumerated Values: 1 intact 2 compromised	.1.3.6.1.4.1.9.9.116.1.9.1.1.15

A list of cable helper entries on Bundle/Sub-Bundle interface.

cdxBundleIpHelperEntry row .1.3.6.1.4.1.9.9.116.1.10.1.1

The conceptual row of cdxBundleIpHelperEntry.
An instance exists for Cable Bundle/Sub-Bundle Interface.

Indexes

IF-MIBifIndex cdxBundleHelperAddr

Column	Syntax	OID
cdxBundleHelperAddr Cable helper IP address	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.116.1.10.1.1.1
cdxBundleHelperType This object describes which kind of device will be associated to a cable helper. The entity may support more than one device class. For example, the entity supports both host and mta. Therefore, bit 1 and bit 3 are set…	Bits Enumerated Values: 0 dva 2 ps 3 stb 4 mta 5 customized 6 host 7 cm	.1.3.6.1.4.1.9.9.116.1.10.1.1.2

Ipv6 dhcp relay configurations on Bundle/Sub-Bundle interface.

cdxBundleIPv6DHCPRelayEntry row .1.3.6.1.4.1.9.9.116.1.11.1.1

The conceptual row of cdxBundleIPv6DHCPRelayTable.
An instance exist for the Bundle/Sub-Bundle interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cdxBundleIPv6DHCPRelayInsertVSSOption Insert VSS option in Relay-Forward Messages	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.116.1.11.1.1.1
cdxBundleIPv6DHCPRelayTrustToRelayReply Interface is trusted to process relay-replies	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.116.1.11.1.1.2
cdxBundleIPv6DHDPRelaySourceIfname Source interface name for IPv6 DHCP relayed messages	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.116.1.11.1.1.3

A list of IPv6 DHCP relay destination entries
on Cable Bundle/Sub-Bundle interfaces.

cdxBundleIPv6DHCPRelayDestEntry row .1.3.6.1.4.1.9.9.116.1.11.2.1

The conceptual row of cdxBundleIPv6DHCPRelayDestTable.
An instance exists for the Cable Bundle/Sub-Bundle interface.

Indexes

IF-MIBifIndex cdxBundleIPv6DHCPRelayDestOutIfVrfIndex cdxBundleIPv6DHCPRelayDestAddr cdxBundleIPv6DHCPRelayDestOutIfIndex

Column	Syntax	OID
cdxBundleIPv6DHCPRelayDestOutIfVrfIndex The vrf identifier that the cdxBundleIPv6DHCPRelayDestOutIfIndex belongs to, it is assigned to each VRF and is used to uniquely identify it, if it is zero, means in global vrf.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.116.1.11.2.1.1
cdxBundleIPv6DHCPRelayDestAddr IPv6 DHCP relay destination address	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.116.1.11.2.1.2
cdxBundleIPv6DHCPRelayDestOutIfIndex The snmp ifIndex of the IPv6 DHCP relay destination output interface. If the ifIndex is 0, it means there is no output interface specified	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.9.9.116.1.11.2.1.3
cdxBundleIPv6DHCPRelayDestSourceAddress IPv6 DHCP relay destination source address	INET-ADDRESS-MIBInetAddressIPv6 Type Constraints: range: 16	.1.3.6.1.4.1.9.9.116.1.11.2.1.4
cdxBundleIPv6DHCPRelayDestLinkAddress IPv6 DHCP relay destination link address	INET-ADDRESS-MIBInetAddressIPv6 Type Constraints: range: 16	.1.3.6.1.4.1.9.9.116.1.11.2.1.5