CISCO-ATM-IF-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
1
Rows
1
Columns
43

ciscoAtmIfTable

table
.1.3.6.1.4.1.9.10.14.1.1 · 1 row entry · 43 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk ciscoAtmIfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ATM-IF-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ATM-IF-MIB::ciscoAtmIfTable' 
This table contains ATM local interface configuration 
parameters, one entry per ATM interface port.
ciscoAtmIfEntry row .1.3.6.1.4.1.9.10.14.1.1.1
This list conatins additonal ATM interface configuration
parameters and state variables.
Indexes
No indexes recorded
Column Syntax OID
ciscoAtmIfType
The type of ATM interface which is either a UNI
(User to Network), PNNI, IISP or NNI PVC only.
To modify the ciscoAtmIftype, ifAdminStatus has
to be down and atmIfIlmiAutoConfiguration disabled.
Enumerationr/w
Enumerated Values:
1other
2uni
3pnni
4iisp
5nniPvcOnly
6aini
 .1.3.6.1.4.1.9.10.14.1.1.1.1
ciscoAtmIfSide
The side of ATM interface which is either a user or
network side.NotApplicable value implies that
ciscoAtmIftype is other than uni or iisp.
Enumerationr/w
Enumerated Values:
1user
2network
3notApplicable
 .1.3.6.1.4.1.9.10.14.1.1.1.2
ciscoAtmIfUniType
The type of User to Network interface is either
private or public. If ciscoAtmIfType is not uni
then ciscoAtmIfUniType value should be ignored.
Enumerationr/w
Enumerated Values:
1public
2private
 .1.3.6.1.4.1.9.10.14.1.1.1.3
ciscoAtmIfPVPs
The number of permanent virtual paths at this
interface.
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.10.14.1.1.1.4
ciscoAtmIfPVCs
The number of permanent virtual channels at this
interface.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.10.14.1.1.1.5
ciscoAtmIfActiveSVPs
The number of active switched virtual paths at
this interface.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.14.1.1.1.6
ciscoAtmIfActiveSVCs
The number of active switched virtual channels at
this interface.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.14.1.1.1.7
ciscoAtmIfTotalConnections
The total number of existing connections at
this interface.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.14.1.1.1.8
ciscoAtmIfConfVplIf
The number of configured VP interfaces at this physical
interface.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.10.14.1.1.1.9
ciscoAtmIfPortType
The type of physical layer medium on the port.
Enumeration
Enumerated Values:
1other
2cpu
3ethernet
4oc3Utp
5oc3SingleModeFiber
6oc3MultiModeFiber
7oc12SingleModeFiber
8ds3
9e3
10ds1
11e1
12oc3Utp3
13oc3Utp5
14oc3SmIr
15oc3SmIrPlus
16oc3SmLr
17oc3Pof
18oc12MultiModeFiber
19oc12SmIr
20oc12SmIrPlus
21oc12SmLr
22oc12Pof
23oc12SmLr2
24oc12SmLr3
25atm25
 .1.3.6.1.4.1.9.10.14.1.1.1.10
ciscoAtmIfXmitLed
The transmit LED color of this port.
Enumeration
Enumerated Values:
1off
2steadyGreen
3steadyYellow
4steadyRed
5flashGreen
6flashYellow
7flashRed
 .1.3.6.1.4.1.9.10.14.1.1.1.11
ciscoAtmIfRecvLed
The receive LED color of this port.
Enumeration
Enumerated Values:
1off
2steadyGreen
3steadyYellow
4steadyRed
5flashGreen
6flashYellow
7flashRed
 .1.3.6.1.4.1.9.10.14.1.1.1.12
ciscoAtmIfXmitCells
The number of cells transmitted of this interface,
including p2p and p2mp cells.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.14.1.1.1.13
ciscoAtmIfRecvCells
The number of cells received of this interface,
including p2p and p2mp cells.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.14.1.1.1.14
ciscoAtmIfSvcMinVcideprecated
The minimum of the range of values from which VCI's
are assigned to new SVC connections. By this value
being larger, more VCI's are reserved for setting up
PVCs. This applies to every VPI of the physical
interface and…
Integer32
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.10.14.1.1.1.15
ciscoAtmIfIlmiConfiguration
Enable/Disable ILMI configuration on this interface.
The configuration takes effect only on the next
interface restart. Disabling this object will also
disable atmIfIlmiAddressRegistration and
atmIfIlmiAutoConfigura…
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.9.10.14.1.1.1.16
ciscoAtmIfIlmiAddressRegistration
Enable/Disable ILMI Address Registration on on
this interface. The configuration takes effect only
on the next interface restart.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.9.10.14.1.1.1.17
ciscoAtmIfIlmiAutoConfiguration
Enable/Disable ILMI link and interface type
determination. The configuration takes effect only on
the next interface restart.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.9.10.14.1.1.1.18
ciscoAtmIfIlmiKeepAlive
The amount of time that should elapse between
successive ILMI keepalive messages sent on this
interface. A value of 0 disables ILMI keepalive messages
on this interface.
secondsInteger32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.10.14.1.1.1.19
ciscoAtmIfSoftVcDestAddress
The 20 byte ATM address of the destination ATM
interface for soft ATM PVC/PVP
NsapAtmAddr
Type Constraints:
range: 20
 .1.3.6.1.4.1.9.10.14.1.1.1.20
ciscoAtmIfUniSignallingVersion
The version of UNI signalling that is currently
being used on the interface. The appropriate
value, either atmfUni3Dot0, atmfUni3Dot1 or
atmfUni4Dot0, is used when the interface is
an UNI or IISP interface. The valu…
Enumerationr/w
Enumerated Values:
1notApplicable
2atmfUni3Dot0
3atmfUni3Dot1
4atmfUni4Dot0
 .1.3.6.1.4.1.9.10.14.1.1.1.21
ciscoAtmIfSvcUpcIntentdeprecated
Determines the policing (Usage Parameter Control or UPC)
action to take for SVCs established through this
interface. Values other than passing are allowed only if
policing is supported on the interface. Also serves t…
Enumerationr/w
Enumerated Values:
1passing
2tagging
3dropping
 .1.3.6.1.4.1.9.10.14.1.1.1.22
ciscoAtmIfAddressTypeobsolete
An indication of the type of the ATM
addresses on this interface. To configure a new
atm address, set ciscoAtmIfAddress to the
address, then set this object to ether nsap(1),
or esi(2), or e164(3), depending on the typ…
Enumerationr/w
Enumerated Values:
1nsap
2esi
3e164
4null
 .1.3.6.1.4.1.9.10.14.1.1.1.23
ciscoAtmIfAddressobsolete
The ATM address of this interface, which
can be either nsap, esi or e164.
For the switch, the nsap/esi address can only
exist on the cpu port.
OctetStringr/w
Constraints:
range: 0-0
range: 6-6
range: 8-8
range: 20-20
 .1.3.6.1.4.1.9.10.14.1.1.1.24
ciscoAtmIfWellKnownVcMode
Indicates whether well-known VCs should be
automatically or manually created for the
interface.

In automatic(1) mode, well-known VCs will be
created with default VPI/VCI values upon startup or
upon en…
Enumerationr/w
Enumerated Values:
1automatic
2manual
3manualDeleteUponEntry
 .1.3.6.1.4.1.9.10.14.1.1.1.31
ciscoAtmIfSignallingAdminStatus
Enable/Disable signalling/sscop on this interface.The
disabled(2) action causes all the active SVCs on
this interface to be cleared.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.9.10.14.1.1.1.32
ciscoAtmIfCdLed
The Cd LED color of this port.
Enumeration
Enumerated Values:
1off
2steadyGreen
 .1.3.6.1.4.1.9.10.14.1.1.1.33
ciscoAtmIfIlmiAccessFilter
The access filter which allows or denies certain
ILMI registered addresses on this interface when
ciscoAtmIfIlmiAddressRegistration is set to enable(1).
permitAll - This permits all ILMI registered addresses.
permitPr…
Enumerationr/w
Enumerated Values:
1permitAll
2permitPrefix
3permitPrefixAndWellknownGroups
4permitPrefixAndAllGroups
5useGlobalDefaultFilter
 .1.3.6.1.4.1.9.10.14.1.1.1.34
ciscoAtmIfConfigAESA
The ATM End System Address (AESA) of this interface
can be configured by entering the full 20 octet AESA,
or the 6 octet ESI and 1 octet Selector Byte.
If the ESI and Selector Byte are entered, the full AESA
will be …
OctetStringr/w
Constraints:
range: 0-0
range: 7-7
range: 20-20
 .1.3.6.1.4.1.9.10.14.1.1.1.35
ciscoAtmIfDerivedAESA
The ATM End System Address (AESA) of this interface.
The AESA is configured using ciscoAtmIfConfigAESA
or can be automatically generated.
A length of zero indicates that no AESA is specified.
For the switch, the AESA ad…
AtmAddr
Type Constraints:
range: 0
range: 8
range: 13
range: 20
 .1.3.6.1.4.1.9.10.14.1.1.1.36
ciscoAtmIfE164Address
The ATM E164 address of this interface.
When a native E.164 number is configured for this
inteface, only native E.164 numbers are
transmitted/received as the called/calling party
numbers. The presence of an ATM E164 …
AtmAddrr/w
Type Constraints:
range: 0
range: 8
range: 13
range: 20
 .1.3.6.1.4.1.9.10.14.1.1.1.37
ciscoAtmIfE164AutoConversionOnly
Enable/Disable E164 auto conversion only on this
interface.
The E164 auto-conversion allows for algorithmic
translation between the native E164 number and E164
AESA address formats.
This object is used when there is n…
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.9.10.14.1.1.1.38
ciscoAtmIfRxCellUpcViolations
The total number of nonconforming cells detected by
Usage Parameter Control (UPC) for cells received on
this interface. This object is not instantiated on
systems that do not have support for collecting such
statistic…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.14.1.1.1.39
ciscoAtmIfRxCellDiscards
The total number of cells that were discarded
within the switch. The cells can be discarded
due to non conformance detected by Usage Parameter
Control (UPC) or queue overflows within the switch.
This object is not inst…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.14.1.1.1.40
ciscoAtmIfIlmiFSMState
The ILMI states meaningful when the value of
ciscoAtmIfIlmiConfiguration indicates that the ILMI
is enabled for an ATM interface:
down -- Stopped or just booted or
interface down
r…
Enumeration
Enumerated Values:
1down
2restarting
3waitDevType
4deviceAndPortTypeComplete
5awaitPnniConfig
6pnniConfigComplete
7awaitRestartAck
8upAndNormal
 .1.3.6.1.4.1.9.10.14.1.1.1.41
ciscoAtmIfIlmiUpDownChanges
The number of times ILMI enters and leaves
the state of upAndNormal.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.14.1.1.1.42
ciscoAtmIfSscopFSMState
The SSCOP state for an ATM interface as
defined by the ITU-T. The state is idle
when the interface is down or SSCOP is
not enabled on the ATM interface
Enumeration
Enumerated Values:
1idle
2outgoingConnectionPending
3incomingConnectionPending
4dataTransferReady
5outgoingDisconnectionPending
6outgoingResyncPending
7incomingResyncPending
8outgoingRecoveryPending
9incomingRecoveryPending
10concurrentResyncPending
 .1.3.6.1.4.1.9.10.14.1.1.1.43
ciscoAtmIfSscopUpDownChanges
The number of times SSCOP enters and leaves
the state of DataTransferReady.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.14.1.1.1.44
ciscoAtmIfSvcUpcIntentCbr
Determines the policing (Usage Parameter Control or UPC)
action to take for Constant Bit Rate SVCs established
through this interface. Values other than passing are
allowed only if policing is supported on the interfa…
UpcMethodr/w
Type Values:
1passing
2tagging
3dropping
 .1.3.6.1.4.1.9.10.14.1.1.1.45
ciscoAtmIfSvcUpcIntentVbrRt
Determines the policing (Usage Parameter Control or UPC)
action to take for Variable Bit Rate - Real Time SVCs
established through this interface. Values other than
passing are allowed only if policing is supported on…
UpcMethodr/w
Type Values:
1passing
2tagging
3dropping
 .1.3.6.1.4.1.9.10.14.1.1.1.46
ciscoAtmIfSvcUpcIntentVbrNrt
Determines the policing (Usage Parameter Control or UPC)
action to take for Variable Bit Rate - Non Real Time SVCs
established through this interface. Values other than
passing are allowed only if policing is supporte…
UpcMethodr/w
Type Values:
1passing
2tagging
3dropping
 .1.3.6.1.4.1.9.10.14.1.1.1.47
ciscoAtmIfSvcUpcIntentAbr
Determines the policing (Usage Parameter Control or UPC)
action to take for Available Bit Rate SVCs established
through this interface. Values other than passing are
allowed only if policing is supported on the interf…
UpcMethodr/w
Type Values:
1passing
2tagging
3dropping
 .1.3.6.1.4.1.9.10.14.1.1.1.48
ciscoAtmIfSvcUpcIntentUbr
Determines the policing (Usage Parameter Control or UPC)
action to take for Unspecified Bit Rate SVCs established
through this interface. Values other than passing are
allowed only if policing is supported on the inte…
UpcMethodr/w
Type Values:
1passing
2tagging
3dropping
 .1.3.6.1.4.1.9.10.14.1.1.1.49