CAPWAP-DOT11-MIB Table View

A table that allows the operator to display and configure
WLAN profiles, such as specifying the MAC type and tunnel mode
for a WLAN.  Also, it helps the AC to configure a WLAN through
the IEEE 802.11 MIB module.
Values of all objects in this table are persistent at
restart/reboot.

capwapDot11WlanEntry row .1.3.6.1.2.1.195.1.1.1

A set of objects that stores the settings of a WLAN profile.

Indexes

capwapDot11WlanProfileId

Column	Syntax	OID
capwapDot11WlanProfileId Represents the identifier of a WLAN profile that has a corresponding capwapDot11WlanProfileIfIndex.	CapwapDot11WlanIdProfileTC Type Constraints: range: 1..512	.1.3.6.1.2.1.195.1.1.1.1
capwapDot11WlanProfileIfIndex Represents the index value that uniquely identifies a WLAN Profile Interface. The interface identified by a particular value of this index is the same interface as identified by the same value of the ifIndex. The creat…	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.2.1.195.1.1.1.2
capwapDot11WlanMacType Represents whether the WTP SHOULD support the WLAN in Local or Split MAC modes.	CAPWAP-BASE-MIBCapwapBaseMacTypeTCr/w Type Values: 0 localMAC 1 splitMAC 2 both	.1.3.6.1.2.1.195.1.1.1.3
capwapDot11WlanTunnelMode Represents the frame tunneling mode to be used for IEEE 802.11 data frames from all stations associated with the WLAN. Bits are exclusive with each other for a specific WLAN profile, and only one tunnel mode could be co…	CAPWAP-BASE-MIBCapwapBaseTunnelModeTCr/w Type Values: 0 localBridging 1 dot3Tunnel 2 nativeTunnel	.1.3.6.1.2.1.195.1.1.1.4
capwapDot11WlanRowStatus This variable is used to create, modify, and/or delete a row in this table. All the objects in a row can be modified only when the value of this object in the corresponding conceptual row is not 'active'. Thus, to modi…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.195.1.1.1.5

A table that stores bindings between WLAN profiles
(identified by capwapDot11WlanProfileId) and WTP Virtual Radio
Interfaces.  The WTP Virtual Radio Interfaces on the AC
correspond to physical layer (PHY) radios on the WTPs.
It also stores the mappings between WLAN IDs and WLAN
Basic Service Set (BSS) Interfaces.
Values of all objects in this table are persistent at
restart/reboot.

capwapDot11WlanBindEntry row .1.3.6.1.2.1.195.1.2.1

A set of objects that stores the binding of a WLAN profile
to a WTP Virtual Radio Interface. It also stores the mapping
between WLAN ID and WLAN BSS Interface.
The INDEX object ifIndex is the ifIndex of a WTP Virtual
R…

Indexes

IF-MIBifIndex capwapDot11WlanProfileId

Column	Syntax	OID
capwapDot11WlanBindWlanId Represents the WLAN ID of a WLAN. During a binding operation, the AC MUST select an unused WLAN ID from between 1 and 16 [RFC5416]. For example, to bind another WLAN profile to a radio that has been bound with a WLAN p…	CapwapDot11WlanIdTC Type Constraints: range: 1..16	.1.3.6.1.2.1.195.1.2.1.1
capwapDot11WlanBindBssIfIndex Represents the index value that uniquely identifies a WLAN BSS Interface. The interface identified by a particular value of this index is the same interface as identified by the same value of the ifIndex. …	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.2.1.195.1.2.1.2
capwapDot11WlanBindRowStatus This variable is used to create, modify, and/or delete a row in this table. All the objects in a row can be modified only when the value of this object in the corresponding conceptual row is not 'active'. Thus, to modi…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.195.1.2.1.3