The PTP radio has changed wireless channel.
This has been caused by either
i) mandatory radar avoidance,
a DFS impulsive interference event will also be
detected,
or
ii) Dynamic Spectrum Optimization, (DSO)
DSO improves link performance by selecting the
most appropriate transmit and receive channels
with the lowest level of interference.
installArmStateTrap
.1.3.6.1.4.1.17713.5.99.0.10
Indicates if the unit is being installed. NB: a value
other than 'disarmed' on startup, or a change of state
during operation may generate an SNMP trap and/or SMTP
email alert
unitOutOfCalibrationTrap
.1.3.6.1.4.1.17713.5.99.0.11
The unit is out of calibration
incompatibleRegionCodesTrap
.1.3.6.1.4.1.17713.5.99.0.14
The master and slave units have incompatible region
codes. NB: Both units must have compatible licence keys
noWirelessChannelAvailableTrap
.1.3.6.1.4.1.17713.5.99.0.15
Spectrum Management was unable to locate a suitable
wireless channel to operate on
wirelessLinkDisabledWarningTrap
.1.3.6.1.4.1.17713.5.99.0.16
The SNMP ifAdminStatus of the wireless interface has
disabled wireless traffic
dataPortDisabledWarningTrap
.1.3.6.1.4.1.17713.5.99.0.17
The SNMP ifAdminStatus of the Ethernet interface has
disabled Ethernet traffic
dataPortConfigurationMismatchTrap
.1.3.6.1.4.1.17713.5.99.0.19
The detection of Ethernet fragments (runt packets) when
the link is in full duplex is an indication of an
auto-negotiation or forced configuration mismatch
dfsImpulsiveInterferenceTrap
.1.3.6.1.4.1.17713.5.99.0.2
DFS impulsive interference detected event
incompatibleMasterAndSlaveTrap
.1.3.6.1.4.1.17713.5.99.0.20
A non-zero value indicates that the master and slave
ends of a link are different hardware products, or have
different software versions. NB: It is very unusual to
detect this, because incompatible units will normally
fail to establish a wireless link. However, some
combinations may establish a partial wireless link and
detect this situation. NB: A non-zero value may generate
an SNMP trap and/or SMTP email alert
sNTPSyncTrap
.1.3.6.1.4.1.17713.5.99.0.21
If SNTP Sync fails then check the server settings in the
Remote Management page, or disable SNTP. NB: a change of
state may generate an SNMP trap and/or SMTP email alert
tDDSynchronizationAlarmTrap
.1.3.6.1.4.1.17713.5.99.0.22
Not Synchronized indicates failure of the external
timing system for a period greater than the holdover
timer. TDD frame timing will have drifted, and this link
may cause interference with other links in a synchronized
network. Timing System Failure is an early warning,
indicating that 80% of the holdover period has expired.
linkModeOptimizationMismatchTrap
.1.3.6.1.4.1.17713.5.99.0.25
The remote node of this link has been configured with a
different link mode optimization
capacityLicenseMismatchTrap
.1.3.6.1.4.1.17713.5.99.0.27
The local and remote units have different licensed
capacity and/or the full capacity trial has been
activated at only one unit. The wireless link is
operating at the capacity of the lowest capacity unit
dataPortStatusTrap
.1.3.6.1.4.1.17713.5.99.0.3
Current status of the Ethernet link. NB: a change of
state may generate an SNMP trap and/or SMTP email alert
syslogStateTrap
.1.3.6.1.4.1.17713.5.99.0.30
The syslog service has been enabled or disabled
syslogLocalNearlyFullTrap
.1.3.6.1.4.1.17713.5.99.0.31
The syslog local log is nearly full (90%)
syslogLocalWrappedTrap
.1.3.6.1.4.1.17713.5.99.0.32
The syslog local log has wrapped
syslogClientTrap
.1.3.6.1.4.1.17713.5.99.0.33
Enable or disable the syslog client
telecomsChannelStatusTrap
.1.3.6.1.4.1.17713.5.99.0.4
Current status of telecoms channel. NB: a change of
state may generate an SNMP trap and/or SMTP email alert
telecomsLoopbackTrap
.1.3.6.1.4.1.17713.5.99.0.6
The loopback status of telecoms channel. This is
intended for installation testing and should be set to
'None' for normal operation. The wire connections to a
unit can be tested by applying a 'Copper' loopback to the
local unit. The wireless connection to the remote unit
can be tested by applying a 'Wireless' loopback to the
remote unit with no loopback on the local unit. When
applying a wireless loopback, please ensure that the
other end of the link has a loopback setting of 'None'.
NB: a change of state may generate an SNMP trap and/or
SMTP email alert
regionCodeTrap
.1.3.6.1.4.1.17713.5.99.0.8
The region code prohibits the wireless unit from
operating outside the regulated limits. An invalid region
code indicates a corrupted licence key. NB: a change of
state may generate an SNMP trap and/or SMTP email alert
installStatusTrap
.1.3.6.1.4.1.17713.5.99.0.9
A non-zero value indicates that signalling was received
with the wrong MAC address or a mismatched link name. NB:
It is very unusual to detect this, because units with
mis-configured Target MAC Address will normally fail to
establish a wireless link. However, rare circumstances
may establish a partial wireless link and detect this
situation. NB: A non-zero value on start-up, or a change
of value during operation, may generate an SNMP trap
and/or SMTP email alert