CADANT-CMTS-DOWNCHANNEL-MIB Table View

This table describes the attributes of downstream
channels (frequency bands).

cadIfDownstreamChannelEntry row .1.3.6.1.4.1.4998.1.1.15.2.1.1

An entry provides a list of attributes for a single
Downstream channel.
An entry in this table exists for each ifEntry with an
ifType of docsCableDownstream(128).

Indexes

cadIfDownChannelIfIndex

Column	Syntax	OID
cadIfDownChannelId The Cable Modem Termination System (CMTS) identification of the downstream channel within this particular MAC interface. If the interface is down, the object returns the most current value. If the downstream channel ID …	Integer32 Constraints: range: -1-255	.1.3.6.1.4.1.4998.1.1.15.2.1.1.1
cadIfDownChannelFrequency The center of the downstream frequency associated with this channel. This object will return the current tuner frequency. If this CMTS interface provides IF output only, this object will return 0 and will be treated as…	hertzInteger32r/w Constraints: range: 0-1000000000	.1.3.6.1.4.1.4998.1.1.15.2.1.1.2
cadIfDownChannelWidth The bandwidth of this downstream channel. Most implementations are expected to support a channel width of 6 MHz (North America) and/or 8 MHz (Europe). See the associated compliance object for a description of the valid…	hertzInteger32r/w Constraints: range: 0-16000000	.1.3.6.1.4.1.4998.1.1.15.2.1.1.3
cadIfDownChannelModulation The modulation type associated with this downstream channel. If the interface is down, this object either returns the configured value (CMTS), the most current value (CM), or the value of unknown(1). See the associated…	Enumerationr/w Enumerated Values: 1 unknown 2 other 3 qam64 4 qam256	.1.3.6.1.4.1.4998.1.1.15.2.1.1.4
cadIfDownChannelInterleave The Forward Error Correction (FEC) interleaving used for this downstream channel. Values are defined as follows: taps8Increment16(3): protection 5.9/4.1 usec, latency .22/.15 msec taps16Incremen…	Enumerationr/w Enumerated Values: 1 unknown 2 other 3 taps8Increment16 4 taps16Increment8 5 taps32Increment4 6 taps64Increment2 7 taps128Increment1 8 taps12increment17 9 taps128increment2 10 taps128increment3 11 taps128increment4 12 taps128increment5 13 taps128increment6 14 taps128increment7 15 taps128increment8	.1.3.6.1.4.1.4998.1.1.15.2.1.1.5
cadIfDownChannelPower The CMTS operational transmit power. If this CMTS interface does not support output power control then this object will return 0 and be treated as read-only. If the interface is down, this object either returns the con…	dBmVInteger32r/w Constraints: range: 0-0 range: 250-600	.1.3.6.1.4.1.4998.1.1.15.2.1.1.6
cadIfDownChannelPowerFineAdj At the CMTS, the fine power adjustments steps to increase or decrease the output power in incremental steps.	StepsInteger32r/w Constraints: range: -80-0	.1.3.6.1.4.1.4998.1.1.15.2.1.1.7
cadIfCmtsCardNumber Card Number associated with this Channel.	CADANT-TCCardId Type Constraints: range: 0..99	.1.3.6.1.4.1.4998.1.1.15.2.1.1.19
cadIfDownChannelCACL1Threshold Percentage of available bandwidth on the channel that can be reserved for admitted/active service flows before the channel goes into Level 1 Overload. When a channel goes into Level 1 Overload, a warning message will …	Integer32r/w Constraints: range: 0-1000	.1.3.6.1.4.1.4998.1.1.15.2.1.1.21
cadIfDownChannelCACL2Threshold Percentage of available bandwidth on the channel that can be reserved for admitted/active service flows before the channel goes into Level 2 Overload. When a channel goes into Level 2 Overload, a warning message will …	Integer32r/w Constraints: range: 0-1000	.1.3.6.1.4.1.4998.1.1.15.2.1.1.22
cadIfDownChannelCACL3Threshold Percentage of available bandwidth on the channel that can be reserved for admitted/active service flows. A Registration Request, DSA Request or DSC Request will be denied due to temporary resource limitations if it wo…	Integer32r/w Constraints: range: 0-1000	.1.3.6.1.4.1.4998.1.1.15.2.1.1.23
cadIfDownChannelMaxRoundTripDelay Maximum round-trip propagation delay for cable plant in Microseconds. Should be configured for the furthest CM in all cable groups containing this DownChannel. Default of 1600 Microseconds is approxiamately 100 miles …	MicrosecondsInteger32r/w Constraints: range: 200-1600	.1.3.6.1.4.1.4998.1.1.15.2.1.1.24
cadIfDownChannelAnnex The value of this object indicates the conformance of the implementation to important regional cable standards. annexA : Annex A from ITU-J83 is used. annexB : Annex B from ITU-J83 is used. annexC : Annex C from ITU-J83…	Enumerationr/w Enumerated Values: 1 unknown 2 other 3 annexA 4 annexB 5 annexC	.1.3.6.1.4.1.4998.1.1.15.2.1.1.26
cadIfDownChannelPCNormAllowedUsage Maximum percentage of downstream resources that may be used by non-emergency telephony services. This is also the maximum amount of resources non-exclusively allocated to sessions of this type. The default is set f…	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.1.1.27
cadIfDownChannelPCNormResUsage Minimum percentage of downstream resources that may be used by non-emergency telephony services. This is also the maximum amount of resources exclusively allocated to sessions of this type. If the value of this obje…	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.1.1.28
cadIfDownChannelPCEmerAllowedUsage Maximum percentage of downstream resources that may be used by emergency telephony services. The default is set from the globals in CadPCMibBase.	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.1.1.29
cadIfDownChannelPCEmerResUsage Minimum percentage of downstream resources that may be used by emergency telephony services. If the value of this object is non-zero, then a portion of the downstream bandwidth will be set aside for normal telephon…	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.1.1.30
cadIfDownChannelPCTotalAllowedUsage Maximum percentage of downstream resources that may be used by both normal and emergency telephony services. The default is set from the globals in CadPCMibBase.	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.1.1.31
cadIfDownChannelPCPreemptionAllowed Indicates whether the system will preempt another session for an emergency call. The default is set from the globals in CadPCMibBase.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.15.2.1.1.32
cadIfDownChannelIfIndex the ifIndex of this downstream channel.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.15.2.1.1.37
cadIfDownChannelPrimaryCapable When a row's cadIfDownChannelPrimaryCapable column is set to true(1) then DOCSIS SYNC message generation is enabled on the downstream channel. Otherwise, DOCSIS SYNC message generation is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.15.2.1.1.38
cadIfDownSpectralInversion When a row's cadIfDownSpectralInversion column is set to true(1), then spectral inversion is enabled. Otherwise, spectral inversion is disabled. Note that spectral inversion is a video PHY parameter not used with DOCS…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.15.2.1.1.39

This status table contains the power parameters for a DS 
OFDM channel.

cadIfDsOfdmPowerEntry row .1.3.6.1.4.1.4998.1.1.15.2.3.1

An entry shows the power setting and measured power
for one of the frequencies within an OFDM channel.

Indexes

cadIfDsOfdmPowerIfIndex cadIfDsOfdmPowerFrequency

Column	Syntax	OID
cadIfDsOfdmPowerIfIndex The ifIndex of this downstream OFDM channel.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.15.2.3.1.1
cadIfDsOfdmPowerFrequency A relative frequency within the OFDM channel for power control/status, in 6 MHz increments(i.e., legal values are 3, 9, 15, etc).	MHzInteger32 Constraints: range: 0-192	.1.3.6.1.4.1.4998.1.1.15.2.3.1.2
cadIfDsOfdmPowerFineAdjustment The configured power for this OFDM channel frequency. This consists of the base RF port power per channel plus any configured tilt adjustment.	dBmVtenthsInteger32r/w Constraints: range: -80-0	.1.3.6.1.4.1.4998.1.1.15.2.3.1.3
cadIfDsOfdmPowerCurrLevel The latest downstream power level reported by the port for this frequency.	DOCS-IF-MIBTenthdBmV	.1.3.6.1.4.1.4998.1.1.15.2.3.1.4
cadIfDsOfdmPowerMinLevel The minimum downstream power level read on the port for this frequency.	DOCS-IF-MIBTenthdBmV	.1.3.6.1.4.1.4998.1.1.15.2.3.1.5
cadIfDsOfdmPowerMaxLevel The minimum downstream power level reported by the port for this frequency.	DOCS-IF-MIBTenthdBmV	.1.3.6.1.4.1.4998.1.1.15.2.3.1.6

This table describes the attributes of downstream
OFDM channels.

cadIfDsOfdmChlEntry row .1.3.6.1.4.1.4998.1.1.15.2.5.1

An entry provides a list of attributes for a single
OFDM Downstream channel.
An entry in this table exists for each ifEntry with an
ifType of docsOfdmDownstream (277).

Indexes

cadIfDsOfdmChlIfIndex

Column	Syntax	OID
cadIfDsOfdmChlIfIndex The ifIndex of this OFDM downstream channel.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.15.2.5.1.1
cadIfDsOfdmChlLowFreq The lowest subcarrier center frequency of the low guard band just below the encompassed spectrum. While this is the center frequency of a subcarrier, it is the low edge frequency of the OFDM channel. The center freque…	hertzInteger32r/w Constraints: range: 0-0 range: 108000000-1770000000	.1.3.6.1.4.1.4998.1.1.15.2.5.1.2
cadIfDsOfdmChlHighFreq The highest subcarrier center frequency of the high guard band just above the encompassed spectrum. While this is the center frequency of a subcarrier, it is the high edge frequency of the OFDM channel. Zero means not…	hertzInteger32r/w Constraints: range: 0-0 range: 132000000-1794000000	.1.3.6.1.4.1.4998.1.1.15.2.5.1.3
cadIfDsOfdmChlPlcBlkLowSubcCentFreq The center frequency of the lowest frequency subcarrier of the 6 MHz encompassed spectrum containing the PLC. Must be an integral number of Megahertz. Zero means not configured. Must be configured to go in-service.	hertzInteger32r/w Constraints: range: 0-0 range: 108000000-1788000000	.1.3.6.1.4.1.4998.1.1.15.2.5.1.4
cadIfDsOfdmChlCyclicPrefix The cyclic-prefix, converted into samples using the sample rate of 204.8 Million samples/second.	samplesInteger32r/w Constraints: range: 192-192 range: 256-256 range: 512-512 range: 768-768 range: 1024-1024	.1.3.6.1.4.1.4998.1.1.15.2.5.1.5
cadIfDsOfdmChlRolloffPeriod The roll-off period used in windowing, converted into samples using the sample rate of 204.8 Million samples/second.	samplesInteger32r/w Constraints: range: 256-256 range: 0-0 range: 64-64 range: 128-128 range: 192-192	.1.3.6.1.4.1.4998.1.1.15.2.5.1.6
cadIfDsOfdmChlTimeIntlvrDepth The number of symbols in the time domain for interleaving. The range is 1..32 for 50 KHz subcarrier spacing, and 1..16 for 25 KHz spacing. A value of one means no time interleaving.	symbolsInteger32r/w Constraints: range: 1-32	.1.3.6.1.4.1.4998.1.1.15.2.5.1.7
cadIfDsOfdmChlSubcSpacing The subcarrier frequency width for this OFDM channel.	hertzInteger32r/w Constraints: range: 50000-50000 range: 25000-25000	.1.3.6.1.4.1.4998.1.1.15.2.5.1.8
cadIfDsOfdmChlContPilotScaleFactor The scale factor M used to calculate the total number of continuous pilots defined using the PLC. The number of continuous pilots also depends on the encompassed bandwidth.	Integer32r/w Constraints: range: 48-120	.1.3.6.1.4.1.4998.1.1.15.2.5.1.9
cadIfDsOfdmChlMaxRoundTripDelay Maximum round-trip propagation delay for cable plant in Microseconds. Should be configured for the furthest CM in all cable groups containing this DownChannel. Default of 800 Microseconds is approxiamately 50 miles be…	MicrosecondsInteger32r/w Constraints: range: 200-1600	.1.3.6.1.4.1.4998.1.1.15.2.5.1.10
cadIfDsOfdmChlPCNormAllowedUsage Maximum percentage of downstream resources that may be used by non-emergency telephony services. This is also the maximum amount of resources non-exclusively allocated to sessions of this type. The default is set f…	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.5.1.11
cadIfDsOfdmChlPCNormResUsage Minimum percentage of downstream resources that may be used by non-emergency telephony services. This is also the maximum amount of resources exclusively allocated to sessions of this type. If the value of this obje…	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.5.1.12
cadIfDsOfdmChlPCEmerAllowedUsage Maximum percentage of downstream resources that may be used by emergency telephony services. The default is set from the globals in CadPCMibBase.	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.5.1.13
cadIfDsOfdmChlPCEmerResUsage Minimum percentage of downstream resources that may be used by emergency telephony services. If the value of this object is non-zero, then a portion of the downstream bandwidth will be set aside for normal telephon…	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.5.1.14
cadIfDsOfdmChlPCTotalAllowedUsage Maximum percentage of downstream resources that may be used by both normal and emergency telephony services. The default is set from the globals in CadPCMibBase.	percentInteger32r/w Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.5.1.15
cadIfDsOfdmChlPCPreemptionAllowed Indicates whether the system will preempt another session for an emergency call. The default is set from the globals in CadPCMibBase.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.15.2.5.1.16
cadIfDsOfdmChlRfPortBasePower The CCAP operational transmit power. See the reference for recommended and required power levels for the equivalent total number of 6 MHz channels on the RF port. The default is the DRFI maximum for 48 6 MHz SC channe…	dBmVInteger32r/w Constraints: range: 250-600	.1.3.6.1.4.1.4998.1.1.15.2.5.1.17
cadIfDsOfdmChlSubcZeroCentFreq The center frequency of subcarrier 0. This is 102.4 MHz less than (cadIfDsOfdmChlLowFreq + cadIfDsOfdmChlHighFreq)/2 if cadIfDsOfdmChlLowFreq is divisible by 250 KHz. Otherwise, it is 102.525 MHz less than (cadIfDsOfd…	hertzSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.15.2.5.1.18
cadIfDsOfdmChlLowActSubcCentFreq The low center frequency of the lowest active subcarrier in the OFDM channel. The low edge of the encompassed spectrum is half a subcarrier less than this value.	hertzSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.15.2.5.1.19
cadIfDsOfdmChlHighActSubcCentFreq The high center frequency of the highest active subcarrier in the the OFDM channel. The high edge of the encompassed spectrum is half a subcarrier more than this value.	hertzSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.15.2.5.1.20
cadIfDsOfdmChlPlcLowSubcCentFreq The center frequency of the lowest frequency subcarrier of the PLC itself. By definition, this is 2.8 MHz higher than cadIfDsOfdmChlPlcBlkLowSubcCentFreq (i.e., the PLC block is 6 MHz, and the 400 KHz PLC is centered i…	hertzSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.15.2.5.1.21
cadIfDsOfdmChlNumActSubc The configured number of subcarriers based on the high and low center frequencies of the active subcarriers in the the OFDM channel.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4998.1.1.15.2.5.1.22

This table describes the read-only attributes of 
downstream OFDM channels (frequency bands).

cadIfDsOfdmChlDataEntry row .1.3.6.1.4.1.4998.1.1.15.2.6.1

An entry provides a list of read-only attributes for a single
OFDM downstream channel.
An entry in this table exists for each ifEntry with an
ifType of docsOfdmDownstream (277).

Indexes

No indexes recorded

Column	Syntax	OID
cadIfDsOfdmChlDataNumActSubcarriers The number of non-excluded subcarriers in the OFDM channel. 7600 is the maximum allowed for a 190 MHz of active Spectrum. 350 would be the worst case for 22 MHz of Active spectrum with 50 KHz subcarriers, with 20 percen…	Integer32 Constraints: range: 200-7600 range: 0-0	.1.3.6.1.4.1.4998.1.1.15.2.6.1.1
cadIfDsOfdmChlDataNumContPilots The total number of continuous pilots. The total number of of continuous pilots is the number defined by the PLC plus the 8 pre-defined ones positioned around the PLC.	Integer32 Constraints: range: 16-128 range: 0-0	.1.3.6.1.4.1.4998.1.1.15.2.6.1.2

This table defines the profiles assigned to an OFDM channel.

cadDsOfdmProfileEntry row .1.3.6.1.4.1.4998.1.1.15.2.8.1

An entry defines one profile on one channel.

Indexes

cadDsOfdmProfileIfIndex cadDsOfdmProfileId

Column	Syntax	OID
cadDsOfdmProfileIfIndex The ifIndex of the channel using this profile.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.15.2.8.1.1
cadDsOfdmProfileId The ID of a profile plus one.	OfdmProfileId Type Constraints: range: 1..3 range: 256	.1.3.6.1.4.1.4998.1.1.15.2.8.1.2
cadDsOfdmProfileDefBitload The default bit-loading (modulation) for this profile. If cadDsOfdmProfileId is 256, only qpsk, qam16, and qam64 are legal. Otherwise, all but qpsk and qam0 are legal.	CerOfdmModTyper/w Type Values: 0 qam0 2 qpsk 4 qam16 6 qam64 7 qam128 8 qam256 9 qam512 10 qam1024 11 qam2048 12 qam4096 13 qam8192 14 qam16384	.1.3.6.1.4.1.4998.1.1.15.2.8.1.3
cadDsOfdmProfileRowStatus The RowStatus for controlling entries in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.15.2.8.1.4

This table provides counts and the average bits per Hertz
per OFDM channel per profile.

cadDsOfdmProfStatEntry row .1.3.6.1.4.1.4998.1.1.15.2.9.1

An entry provides the values for one profile on one channel.

Indexes

cadDsOfdmProfStatIfIndex cadDsOfdmProfStatProfId

Column	Syntax	OID
cadDsOfdmProfStatIfIndex The ifIndex of this OFDM downstream channel.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.15.2.9.1.1
cadDsOfdmProfStatProfId The profile number plus one of this profile on this channel.	OfdmProfileId Type Constraints: range: 1..3 range: 256	.1.3.6.1.4.1.4998.1.1.15.2.9.1.2
cadDsOfdmProfStatAvgBitsPerSubc The average number of bits per subcarrier times 100 across all active subcarriers on the channel, rounded to nearest hundredth. Continuous pilots and subcarriers in the PLC are not included in this calculation, even th…	HundredthBitSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4998.1.1.15.2.9.1.3
cadDsOfdmProfStatReqMods The modulations used by this profile and any exceptions to this profile.	CerOfdmModBitsType Type Values: 0 qam32768 1 qam16384 2 qam8192 3 qam4096 4 qam2048 5 qam1024 6 qam512 7 qam256 8 qam128 9 qam64 10 qam32 11 qam16 12 qam8 13 qpsk 14 bpsk 15 zeroBitload	.1.3.6.1.4.1.4998.1.1.15.2.9.1.4
cadDsOfdmProfStatEtherFrameBytes The count of Layer 2 Ethernet frame bytes that have been sent on this channel using this specific profile.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.15.2.9.1.5
cadDsOfdmProfStatTotalCodewords The number of codewords sent on this channel using this specific profile.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4998.1.1.15.2.9.1.6
cadDsOfdmProfStat30SecCwUtil The codeword utilization percentage of this profile on this channel. The utilization is measured over the last 30 seconds.	Unsigned32 Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.9.1.7
cadDsOfdmProfStat30SecCwEff The Efficiency percentage of this profile on this channel over the last 30 seconds (i.e,. the average number of data bits per codeword used by this profile, divided by the size of a codeword).	Unsigned32 Constraints: range: 0-100	.1.3.6.1.4.1.4998.1.1.15.2.9.1.8

This table defines exceptions to profiles on an OFDM channel.

cadDsOfdmProfExceptionEntry row .1.3.6.1.4.1.4998.1.1.15.2.11.1

An entry defines one profile exception.

Indexes

cadDsOfdmProfExceptionIfIndex cadDsOfdmProfExceptionProfId cadDsOfdmProfExceptionLowFreq

Column	Syntax	OID
cadDsOfdmProfExceptionIfIndex The ifIndex of the channel using this profile.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4998.1.1.15.2.11.1.1
cadDsOfdmProfExceptionProfId The Id of a profile plus one.	OfdmProfileId Type Constraints: range: 1..3 range: 256	.1.3.6.1.4.1.4998.1.1.15.2.11.1.2
cadDsOfdmProfExceptionLowFreq The low edge frequency of a frequency range being assigned a different bit-loading type from the default for the profile.	hertzInteger32 Constraints: range: 108000000-1770000000	.1.3.6.1.4.1.4998.1.1.15.2.11.1.3
cadDsOfdmProfExceptionHighFreq The high edge frequency of a frequency range being assigned a different bit-loading type from the default for the profile.	hertzInteger32r/w Constraints: range: 0-0 range: 108000000-1770000000	.1.3.6.1.4.1.4998.1.1.15.2.11.1.4
cadDsOfdmProfExceptionSkip True if using different bit-loading for odd and even numbered subcarriers in this frequency range. False if all subcarriers in the range use the single bit-loading type given by cadDsOfdmProfExceptionMainBitload.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4998.1.1.15.2.11.1.5
cadDsOfdmProfExceptionMainBitload The main bit-loading (modulation) for this frequency range. If skip is true, this is the bit-loading for only the even numbered subcarriers. If false, it is for all subcarriers.	CerOfdmModTyper/w Type Values: 0 qam0 2 qpsk 4 qam16 6 qam64 7 qam128 8 qam256 9 qam512 10 qam1024 11 qam2048 12 qam4096 13 qam8192 14 qam16384	.1.3.6.1.4.1.4998.1.1.15.2.11.1.6
cadDsOfdmProfExceptionOddBitload The bit-loading (modulation) for the odd numbered subcarriers when skip is true. Ignored if skip is false.	CerOfdmModTyper/w Type Values: 0 qam0 2 qpsk 4 qam16 6 qam64 7 qam128 8 qam256 9 qam512 10 qam1024 11 qam2048 12 qam4096 13 qam8192 14 qam16384	.1.3.6.1.4.1.4998.1.1.15.2.11.1.7
cadDsOfdmProfExceptionRowStatus The RowStatus for controlling entries in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4998.1.1.15.2.11.1.8