BINTEC-POTS-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
4
Rows
4
Columns
91

potsIfTable

table
.0.14.1.1 · 1 row entry · 13 columns
Open in standard view
Uses the bintec variant from /opt/observium/mibs/bintec.
Command help
Walk potsIfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'BINTEC-POTS-MIB' -M '/opt/observium/mibs/bintec:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'BINTEC-POTS-MIB::potsIfTable' 
The potsIfTable contains configuration information
for the POTS outlets.
potsIfEntry row .0.14.1.1.1
Indexes
Column Syntax OID
potsSlot
Identification number of the used slot.
Integer32
Constraints:
range: 0-31
 .0.14.1.1.1.1
potsUnit
Identification number of the used unit.
Integer32
Constraints:
range: 0-31
 .0.14.1.1.1.2
potsType
The type of the connected device on socket a.

Possible values are:
- any(1), (multifunctional)
- fax(2),
- telephony(3),
- modem(4),
- disable(5),
…
Enumerationr/w
Enumerated Values:
1any
2fax
3telephony
4modem
5disable
6doorintercom
7answering
8emergency
9alarmInput
 .0.14.1.1.1.3
potsIfMode
Type of outlet.
Enumeration
Enumerated Values:
1fxo
2fxs
 .0.14.1.1.1.4
potsIfAdminState
This variable allows for taking an POTS interface out of/in
service w/o having to touch the configuration.

Besides, it is possible to initiate a reconfiguration for that
interface in case a mismatch in co…
Enumerationr/w
Enumerated Values:
1down
2up
3reconfig
 .0.14.1.1.1.5
potsIfOperState
The operational state of an interface is indicated via this
variable.
Possible values are:
- down(1),
- running(2),
- fail(3),
- not-connected(4),
- stopped(5),
- stopping(6),
…
Enumeration
Enumerated Values:
1down
2running
3fail
4not-connected
5stopped
6stopping
7starting
 .0.14.1.1.1.6
potsIfIndex
Reference to the FXS or FXO table.
PotsIfIndex .0.14.1.1.1.7
potsIfTtxLevel
Teletax (metering pulse) level:
for FXS lines: output level
for FXO lines: minimum level
Integer32r/w
Constraints:
range: -50-0
 .0.14.1.1.1.8
potsIfTtxFreq
Teletax (metering pulse) frequency:
1: no teletax output/reception
3: 12 kHz
4: 16 kHz
Enumerationr/w
Enumerated Values:
1off
3freq12khz
4freq16khz
 .0.14.1.1.1.9
potsIfCoeffIndex
Selection of the coefficient set provided
by the FXS or FXO line driver. This allows
to use specific settings with e.g. resistive or
complex line impedances. Supported values are:
600: 600 ohms (resistive)
11…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .0.14.1.1.1.10
potsIfTxGain
Amplification or attenuation (negative gain)
of outgoing audio in dB.
dBInteger32r/w
Constraints:
range: -30-10
 .0.14.1.1.1.11
potsIfRxGain
Amplification or attenuation (negative gain)
of incoming audio in dB.
dBInteger32r/w
Constraints:
range: -30-10
 .0.14.1.1.1.12
potsIfDialInTimeout
Limit for time interval between two consecutive
dialling digits.
sInteger32r/w
Constraints:
range: 1-99
 .0.14.1.1.1.13

potsIfFxoTable

table
.0.14.1.2 · 1 row entry · 42 columns
Open in standard view
Uses the bintec variant from /opt/observium/mibs/bintec.
Command help
Walk potsIfFxoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'BINTEC-POTS-MIB' -M '/opt/observium/mibs/bintec:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'BINTEC-POTS-MIB::potsIfFxoTable' 
The potsIfFxoTable contains configuration information
for the FXO outlets.
potsIfFxoEntry row .0.14.1.2.1
Indexes
Column Syntax OID
potsIfFxoIfIndex
Index of the FXO interface.
PotsIfIndexr/w .0.14.1.2.1.1
potsIfFxoFlashTime
Dial out flash time (ms).
msSNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .0.14.1.2.1.2
potsIfFxoDialToneDetectionobsolete
Type of tone:
off(1) no dial tone detection
single(2) detect just one tone rhythm
dual(3) detect also an alternative tone rhythm

Enable dial tone detection. The following entries describes the
…
Enumerationr/w
Enumerated Values:
1off
2single
3dual
 .0.14.1.2.1.3
potsIfFxoDialToneDetectionTimeobsolete
Activation time for dial tone detection in seconds. When this
time is reached dial tone detection will be switched off.
A zero value keeps dial tone detection endlessly active.
sSNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .0.14.1.2.1.4
potsIfFxoDialToneMinLevelobsolete
minimum dial tone level.
dBReceiveLevelr/w
Type Constraints:
range: -50..0
 .0.14.1.2.1.5
potsIfFxoDialToneOrgFreqobsolete
Frequency of the expected dial tone (Hz).
HzToneFrequencyr/w
Type Constraints:
range: 300..3400
 .0.14.1.2.1.6
potsIfFxoDialToneOrgCadenceobsolete
Cadence of the expected dial tone.

The cadence definition consists of times of activity, times
of no activity and some control information. All information
is concatenated to one string and all times are…
CadenceStringr/w
Type Constraints:
range: 0..127
 .0.14.1.2.1.7
potsIfFxoDialToneOrgToleranceobsolete
Dial tone timing tolerance (%).
%CadenceTimingTolerancer/w
Type Constraints:
range: 0..100
 .0.14.1.2.1.8
potsIfFxoDialToneAltFreqobsolete
Alternative dial tone frequncy (Hz).
HzToneFrequencyr/w
Type Constraints:
range: 300..3400
 .0.14.1.2.1.9
potsIfFxoDialToneAltCadenceobsolete
Alternative dial tone cadence. For a description of
allowed format refer to potsIfFxoDialToneOrgCadence.
CadenceStringr/w
Type Constraints:
range: 0..127
 .0.14.1.2.1.10
potsIfFxoDialToneAltToleranceobsolete
Alternative dial tone timing tolerance (%).
%CadenceTimingTolerancer/w
Type Constraints:
range: 0..100
 .0.14.1.2.1.11
potsIfFxoBusyToneDetectionobsolete
Type of tone:
off(1) no busy tone detection
single(2) detect just one tone rhythm
dual(3) detect also an alternative tone rhythm

Enable busy tone detection.
Enumerationr/w
Enumerated Values:
1off
2single
3dual
 .0.14.1.2.1.12
potsIfFxoBusyToneDetectionTimeobsolete
Activation time for busy tone detection in seconds. When this
time is reached busy tone detection will be switched off.
A zero value keeps busy tone detection endlessly active.
sSNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .0.14.1.2.1.13
potsIfFxoBusyToneMinLevelobsolete
Minimum busy tone level (dB).
dBReceiveLevelr/w
Type Constraints:
range: -50..0
 .0.14.1.2.1.14
potsIfFxoBusyToneOrgFreqobsolete
Busy tone frequncy (Hz).
HzToneFrequencyr/w
Type Constraints:
range: 300..3400
 .0.14.1.2.1.15
potsIfFxoBusyToneOrgCadenceobsolete
Busy tone cadence. For a description of allowed
format refer to potsIfFxoDialToneOrgCadence.
CadenceStringr/w
Type Constraints:
range: 0..127
 .0.14.1.2.1.16
potsIfFxoBusyToneOrgToleranceobsolete
Busy tone timing tolerance (%).
%CadenceTimingTolerancer/w
Type Constraints:
range: 0..100
 .0.14.1.2.1.17
potsIfFxoBusyToneAltFreqobsolete
Alternative busy tone frequncy.
ToneFrequencyr/w
Type Constraints:
range: 300..3400
 .0.14.1.2.1.18
potsIfFxoBusyToneAltCadenceobsolete
Alternative busy tone cadence. For a description of
allowed format refer to potsIfFxoDialToneOrgCadence.
CadenceStringr/w
Type Constraints:
range: 0..127
 .0.14.1.2.1.19
potsIfFxoBusyToneAltToleranceobsolete
Alternative busy tone timing tolerance (%).
%CadenceTimingTolerancer/w
Type Constraints:
range: 0..100
 .0.14.1.2.1.20
potsIfFxoDialOutMode
Dial-out mode (1: pulse, 2: DTMF).
Enumerationr/w
Enumerated Values:
1pulse
2dtmf
 .0.14.1.2.1.21
potsIfFxoDialOutDelay
Waiting time before dialout starts (ms).
msSNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .0.14.1.2.1.22
potsIfFxoDialInMode
Dial-in mode (1: off, 2: DTMF, 3: UEFS).
Enumerationr/w
Enumerated Values:
1off
2dtmf
3uefs
 .0.14.1.2.1.23
potsIfFxoDialInProgressTone
The progress tone is used for dial in mode 'DTMF' only.
Other dial in modes will ignore this entry. The progress tone
will signal the caller when to start to dial the subscriber
number. After reception of the first di…
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .0.14.1.2.1.24
potsIfFxoDialInProgressToneDef
Index of the progress tone definition in phoneIfToneTable.
ToneTabIndexr/w .0.14.1.2.1.25
potsIfFxoDialPulsePulseTime
Pulse dialling break time (ms).
msInteger32r/w
Constraints:
range: 30-200
 .0.14.1.2.1.26
potsIfFxoDialPulsePauseTime
Pulse dialling make time (ms).
msInteger32r/w
Constraints:
range: 30-200
 .0.14.1.2.1.27
potsIfFxoDialPulseInterDigitTime
DTMF dialling interdigit time (ms).
msInteger32r/w
Constraints:
range: 100-500
 .0.14.1.2.1.28
potsIfFxoDialDtmfLevel
DTMF tone level (dB).
dBTransmitLevelr/w
Type Constraints:
range: -30..0
 .0.14.1.2.1.29
potsIfFxoDialDtmfToneTime
DTMF tone duration (ms).
msInteger32r/w
Constraints:
range: 50-250
 .0.14.1.2.1.30
potsIfFxoDialDtmfInterDigitTime
DTMF dialling interdigit time (ms).
msInteger32r/w
Constraints:
range: 50-250
 .0.14.1.2.1.31
potsIfFxoDataLinkMinLevel
Minimum data transmission level (dB).
dBTransmitLevelr/w
Type Constraints:
range: -30..0
 .0.14.1.2.1.32
potsIfFxoDataLinkModeOnHook
Allowed on-hook data transmission modes:
dt-as: data transmission prior to ringing with DT-AS
dt-as-pol-rev: data transmission prior to ringing with DT-AS
and polarity reversal
rp-as: …
Bitsr/w
Enumerated Values:
0dt-as
1dt-as-pol-rev
2rp-as
3during-ringing
4dtmf
 .0.14.1.2.1.33
potsIfFxoDataLinkModeOffHook
Selection of off-hook data transmission mode:
1: no off-hook data transmission
2: data transmission prior using DT-AS
Enumerationr/w
Enumerated Values:
1off
2dt-as
 .0.14.1.2.1.34
potsIfFxoFaxToneDetection
Fax tone detection. Tones to detect according to ITU T.30:
cng: fax announce tone 1100 Hz
ced: fax answer tone 2100 Hz
dis: digital identification signal V.21
Bitsr/w
Enumerated Values:
0cng
1ced
2dis
 .0.14.1.2.1.35
potsIfFxoKeyBreakDetection
Detection of key break as a release condition.
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .0.14.1.2.1.36
potsIfFxoDialOutToneDetection
Detection of dial tones as a trigger for outgoing dial.
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .0.14.1.2.1.37
potsIfFxoNormalDialTone
Index of the normal dial tone definition in
phoneIfToneTable used by dial out tone detection.
ToneDefTabIndexr/w .0.14.1.2.1.38
potsIfFxoSpecialDialTone
Index of the special dial tone definition in
phoneIfToneTable used by dial out tone detection.
ToneDefTabIndexr/w .0.14.1.2.1.39
potsIfFxoConcurrentToneDetection
Detection of tones after dialling and during a connection
to catch a release condition.
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .0.14.1.2.1.40
potsIfFxoBusyTone
Index of the busy tone definition in phoneIfToneTable
used by concurrent tone detection.
ToneDefTabIndexr/w .0.14.1.2.1.41
potsIfFxoCongestionTone
Index of the congestion tone definition in phoneIfToneTable
used by concurrent tone detection.
ToneDefTabIndexr/w .0.14.1.2.1.42

potsIfFxsTable

table
.0.14.1.3 · 1 row entry · 17 columns
Open in standard view
Uses the bintec variant from /opt/observium/mibs/bintec.
Command help
Walk potsIfFxsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'BINTEC-POTS-MIB' -M '/opt/observium/mibs/bintec:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'BINTEC-POTS-MIB::potsIfFxsTable' 
The potsIfFxsTable contains configuration information
for the FXS outlets.
potsIfFxsEntry row .0.14.1.3.1
Indexes
Column Syntax OID
potsIfFxsIfIndex
Index of the FXS interface.
PotsIfIndexr/w .0.14.1.3.1.1
potsIfFxsFlashMinTime
Minimum flash duration (ms). Flash pulses below this
value will be ignored.
msSNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .0.14.1.3.1.2
potsIfFxsFlashMaxTime
Maximum flash duration (ms). Flash pulses above this
value will be interpreted as hook-on.
msSNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .0.14.1.3.1.3
potsIfFxsRingLevel
Peak value of sinusoidal ringing voltage.
VpeakInteger32r/w
Constraints:
range: 0-150
 .0.14.1.3.1.4
potsIfFxsRingFreq
Frequency of sinusoidal ringing voltage.
Enumerationr/w
Enumerated Values:
1freq25hz
2freq50hz
 .0.14.1.3.1.5
potsIfFxsRingTableIndex
The ringing table index is the reference to
all ringing cadences used for this extension.
Definitions are in phoneIfRingTable.
RingTabIndexr/w .0.14.1.3.1.6
potsIfFxsToneTableIndex
The tone table index refers to the tones
used for this extension. Definitions are
in phoneIfToneTable
ToneTabIndexr/w .0.14.1.3.1.7
potsIfFxsDataLinkType
Allowed data transmission message types:
setup - call setup message
mwi - message waiting indicator message
aoc - advice of charge message
sms - short message service message
Bitsr/w
Enumerated Values:
0setup
1mwi
2aoc
3sms
 .0.14.1.3.1.8
potsIfFxsDataLinkElem
Allowed data transmission parameters (see ETSI EN 300 659-3).
Not selected elements will be filtered out and not sent to
the subscriber.
Bitsr/w
Enumerated Values:
0date-time
1calling-line-id
2called-line-id
3reason-for-absence-of-cli
4calling-party-name
5reason-for-absence-of-cpn
6visual-indicator
7message-identification
8last-message-cli
9complementary-date-time
10complementary-cli
11call-type
12first-cli
13no-of-messages
14charge
15additional-charge
16duration-of-call
17network-provider-id
18carrier-id
19select-terminal-function
20display-information
21service-information
 .0.14.1.3.1.9
potsIfFxsDataLinkLevel
Level of the data transmission signal (dB).
dBTransmitLevelr/w
Type Constraints:
range: -30..0
 .0.14.1.3.1.10
potsIfFxsDataLinkTiming
Index of the timer set to be used for on-hook and off-hook
data transmission.
DataLinkTimerTabIndexr/w .0.14.1.3.1.11
potsIfFxsDataLinkModeOnHook
Selection of on-hook data transmission mode:
1: no on-hook data transmission
2: data transmission prior to ringing with DT-AS
3: data transmission prior to ringing with DT-AS
and polarity reversal
4: data trans…
Enumerationr/w
Enumerated Values:
1off
2dt-as
3dt-as-pol-rev
4rp-as
5during-ringing
6dtmf
 .0.14.1.3.1.12
potsIfFxsDataLinkModeOffHook
Selection of off-hook data transmission mode:
1: no off-hook data transmission
2: data transmission prior using DT-AS
Enumerationr/w
Enumerated Values:
1off
2dt-as
 .0.14.1.3.1.13
potsIfFxsDialPulseMinTimePulse
Pulse dialling break time minimum (ms). Break pulses below
this limit will be ignored.
msInteger32r/w
Constraints:
range: 10-100
 .0.14.1.3.1.14
potsIfFxsDialPulseMaxTimePulse
Pulse dialling break time maximum (ms). A pause time above
this limit is regarded as on-hook signal.
msInteger32r/w
Constraints:
range: 50-200
 .0.14.1.3.1.15
potsIfFxsDialPulseMinTimePause
Pulse dialling make time minimum (ms). Make pulses below
this limit will be ignored.
msInteger32r/w
Constraints:
range: 10-100
 .0.14.1.3.1.16
potsIfFxsDialPulseMaxTimePause
Pulse dialling make time maximum (ms). A pause time above
this limit finishes the pulse counting and this digit is
regarded as complete.
msInteger32r/w
Constraints:
range: 10-300
 .0.14.1.3.1.17

potsIfDataLinkTimerTable

table
.0.14.1.4 · 1 row entry · 19 columns
Open in standard view
Uses the bintec variant from /opt/observium/mibs/bintec.
Command help
Walk potsIfDataLinkTimerTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'BINTEC-POTS-MIB' -M '/opt/observium/mibs/bintec:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'BINTEC-POTS-MIB::potsIfDataLinkTimerTable' 
The potsIfDataLinkTimerTable the contains timer values (in ms)
controlling on-hook and off-hook data transmission service 
according to ETSI EN 300 659. The reception of data is 
controlled with timers according to the minimum and maximum
values given in the ETSI standard.
potsIfDataLinkTimerEntry row .0.14.1.4.1
Indexes
Column Syntax OID
potsIfDataLinkTimerIndex
Index of the set of timers which is following up.
DataLinkTimerTabIndexr/w .0.14.1.4.1.1
potsIfDataLinkTimer0
Timer T0 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 100-550
 .0.14.1.4.1.2
potsIfDataLinkTimer1
Timer T1 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 45-500
 .0.14.1.4.1.3
potsIfDataLinkTimer2
Timer T2 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 200-500
 .0.14.1.4.1.4
potsIfDataLinkTimer3
Timer T3 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 500-800
 .0.14.1.4.1.5
potsIfDataLinkTimer4
Timer T4 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 45-500
 .0.14.1.4.1.6
potsIfDataLinkTimer5
Timer T5 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 500-2000
 .0.14.1.4.1.7
potsIfDataLinkTimer6
Timer T6 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 200-3000
 .0.14.1.4.1.8
potsIfDataLinkTimer7
Timer T7 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 250-700
 .0.14.1.4.1.9
potsIfDataLinkTimer8
Timer T8 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 200-500
 .0.14.1.4.1.10
potsIfDataLinkTimer9
Timer T9 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 0-150
 .0.14.1.4.1.11
potsIfDataLinkTimer10
Timer T10 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 0-150
 .0.14.1.4.1.12
potsIfDataLinkTimer11
Timer T11 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 40-55
 .0.14.1.4.1.13
potsIfDataLinkTimer12
Timer T12 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 55-200
 .0.14.1.4.1.14
potsIfDataLinkTimer13
Timer T13 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 40-120
 .0.14.1.4.1.15
potsIfDataLinkTimer14
Timer T14 according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 155-165
 .0.14.1.4.1.16
potsIfDataLinkTimerRpAs
Timer RP-AS according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 200-300
 .0.14.1.4.1.17
potsIfDataLinkTimerDtAsOnH
Timer DT-AS on-hook according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 90-110
 .0.14.1.4.1.18
potsIfDataLinkTimerDtAsOffH
Timer DT-AS off-hook according to ETSI EN 300 659.
Integer32r/w
Constraints:
range: 75-85
 .0.14.1.4.1.19