BIANCA-BRICK-SERIAL-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
1
Rows
1
Columns
28

serialIfTable

table mandatory
.1.3.6.1.4.1.272.4.25.1 · 1 row entry · 28 columns
Open in standard view
Uses the bintec variant from /opt/observium/mibs/bintec.
Command help
Walk serialIfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'BIANCA-BRICK-SERIAL-MIB' -M '/opt/observium/mibs/bintec:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'BIANCA-BRICK-SERIAL-MIB::serialIfTable' 
The serialIfTable contains information relating to the 
interfaces available on the system. Each entry corresponds to
an available serial interface. Entries cannot be added or 
	deleted by the user. 
          
Creating entries: Entries are created by the system
automatically when a new serial module is installed.
          
Deleting entries: Entries are removed by the system
after the appropriate serial module is removed.
serialIfEntry row .1.3.6.1.4.1.272.4.25.1.1
Indexes
Column Syntax OID
serialIfIndexmandatory
Unique interface index of the serial interface.
Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.272.4.25.1.1.1
serialIfTypemandatory
The serial physical interface type
none(1) interface disabled
x21(2) X21(V11) terminated (sync)
v35(3) V35(V11 & V28) (sync)
v36(4) V36(V10 & V11) (sync)
x21bis(5) RS232(V28) …
Enumerationr/w
Enumerated Values:
1none
2x21
3v35
4v36
5x21bis
6rs422
7rs449
8rs530
9rs530a
 .1.3.6.1.4.1.272.4.25.1.1.2
serialIfConnectormandatory
The physical connector type.
When configured as DCE the pins on the output connector
act as a DCE interface. If configured as DTE on the output
connector act as a DTE interface.
dte(1) DTE output pins
dce(2) DC…
Enumerationr/w
Enumerated Values:
1dte
2dce
 .1.3.6.1.4.1.272.4.25.1.1.3
serialIfLeadsmandatory
The value of IfLeads has influence on the state of the
physical layer (L1State). When configured as
IfLeads=enabled, the state of the physical layer
depends on the signals of the control interface pins
Indication/Contro…
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.272.4.25.1.1.4
serialIfClockmandatory
The physical layer (layer 1) clocking mode.
When configured as AUTO the clock provided depends what is
configured on connector. If connector is configured as
DTE clock must provided from external, if the connector is
co…
Enumerationr/w
Enumerated Values:
1auto
2extern
3intern
 .1.3.6.1.4.1.272.4.25.1.1.5
serialIfClockEdgemandatory
The value of IfClockEdge influences the (internal) active
clock edge(s) for generating/sampling data on the serial line.
This value should be left on DEFAULT under normal
circumstances. Nevertheless, in some rare cas…
Enumerationr/w
Enumerated Values:
1default
2rxc-inverted
3txc-inverted
4rxc-txc-inverted
 .1.3.6.1.4.1.272.4.25.1.1.6
serialIfSpeedmandatory
The serial interface speed in bits per second. The range
is dependant on the type of the line (balanced/unbalanced)
and the quality and length of the cable.
Over a short distance (about 5 m) and with a shielded cable
s…
Integer32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.272.4.25.1.1.8
serialIfL2Modemandatory
The layer 2 mode. This value has influence on the
HDLC address field (first byte of a HDCL frame). When
configured as DTE the address in a command frame is
0x01, when configured as DCE it is 0x03. For
response frames it…
Enumerationr/w
Enumerated Values:
1dte
2dce
3auto
 .1.3.6.1.4.1.272.4.25.1.1.10
serialIfCableDetectionmandatory
Cable autodetection for:
manual(1) disabled
auto(2) serialIfType and serialIfConnector
iftype(3) serialIfType
connector(4) serialIfConnector
Enumerationr/w
Enumerated Values:
1manual
2auto
3iftype
4connector
 .1.3.6.1.4.1.272.4.25.1.1.11
serialIfCableTypemandatory
Show the detected cable type:
unknown(1) cable type unknown.
x21(2) DB15, X27/V11 (sync)
v35(3) M34, V35/V10 (sync)
v36(4) DB37, V10/V11 (sync)
x21bis(5) DB…
Enumeration
Enumerated Values:
1unknown
2x21
3v35
4v36
5x21bis
255not-supported
 .1.3.6.1.4.1.272.4.25.1.1.12
serialIfCableConnectormandatory
Show the detected cable connector type:
dte(1) DTE cable
dce(2) DCE cable
unknown(3) cable type unknown.
not-supported(4) cable detection not supported.
Enumeration
Enumerated Values:
1dte
2dce
3unknown
4not-supported
 .1.3.6.1.4.1.272.4.25.1.1.13
serialIfBundlemandatory
Index of the bundle to aggregate multiple Channels
to one interface.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.272.4.25.1.1.14
serialIfL1Statemandatory
The serial physical layer state
dn(1) physical layer is inactive
up(2) physical layer is active
Enumeration
Enumerated Values:
1dn
2up
 .1.3.6.1.4.1.272.4.25.1.1.15
serialIfSpeedRealmandatory
In DCE/internal clock mode this is the rounded speed in bits per
second, because not every baudrate can exactly be generated.
In DTE/external clock mode this is the measured speed, where
measurement is possible, or the …
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.16
serialIfLicensemandatory
Shows wether a serial license associated with this serial port
port is required, missing or in use.
Enumeration
Enumerated Values:
1not-required
2missing
3used
 .1.3.6.1.4.1.272.4.25.1.1.17
serialIfRxPacketsmandatory
Count of received valid Frames.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.20
serialIfRxOctetsmandatory
Count of received bytes.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.21
serialIfTxPacketsmandatory
Count of transmitted valid Frames.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.22
serialIfTxOctetsmandatory
Count of transmitted bytes.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.23
serialIfRxResetsmandatory
Count of receiver resets. Under rare circumstances it
might be necessary to reset the receiver to work
properly.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.24
serialIfRxAbortsmandatory
Count of receiver aborts. The sender of a frame can
indicate a frame as aborted with a special Abort
sequence.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.25
serialIfRxOverrunsmandatory
Count of receiver overruns. If the serial port is unable
to grant sufficiently soon/often the bus, the
RxFIFO may fill up. This leads to loss of data.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.26
serialIfRxCRCErrorsmandatory
Count of corrupted frames. Errors due to interference
on the serial cable.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.27
serialIfRxGiantFramesmandatory
Count of received frames with illegal framesize. This
can occur if a frame delimiter is destroyed.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.28
serialIfTxResetsmandatory
Count of transmitter resets. Under rare circumstances
it might be necessary to reset the transmitter to work
properly.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.29
serialIfTxAbortsmandatory
Count of transmitter aborts. While sending a frame it
might be necessary to indicate this frame as aborted. In
this case the receiver regards this frame as illegal.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.30
serialIfTxUnderrunsmandatory
Count of transmitter underruns. The serial data for the
serial port is supplied too slowly.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.31
serialIfTxGiantFramesmandatory
Count of transmitted frames with illegal
framesize. This can occur if an upper module creates
packets with more than the maximum allowed packet size.
RFC1155-SMICounter
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.272.4.25.1.1.32