A3Com-PortPath-r6-MIB Table View

A table of physical interfaces.

a3ComPathEntry row .1.3.6.1.4.1.43.2.16.2.1

Indexes

a3ComPathIndex

Column	Syntax	OID
a3ComPathIndexmandatory A unique identifier for each path. The value for each path must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.16.2.1.1
a3ComPathNamemandatory A descriptive name for the path	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.43.2.16.2.1.2
a3ComPathPortmandatory The index of the entry in the Port table to which this path entry has been assigned. Unassigned entries have a value of zero. This object allows adding and deleting paths from ports.In order for any modifications to ta…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.16.2.1.3
a3ComPathItcmOptionmandatory This object should be set to compatible if the bridge/router is attached via a serial link to a 3Com Series/1 based bridge or bridge/router (IB/3, BR/3) that contains an ITCM board.	Enumerationr/w Enumerated Values: 1 compatible 2 incompatible	.1.3.6.1.4.1.43.2.16.2.1.4
a3ComPathT1Modemandatory Enabling this object allows for better line speed than if this were disabled. However, do not enable this object when a3ComPathItcmOpt is set to compatible.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.43.2.16.2.1.5
a3ComPathCryptoResyncmandatory Enabling this parameter causes the router to resynch with any attached KG84/91 devices. This only applies to the 449 interface of a wide area bridge/router.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.43.2.16.2.1.6
a3ComPathCRCmandatory This controls the type of Cyclic Redundancy Check that is performed on a serial line. In order for any modifications to take effect, the path must be enabled(re-enabled if it is already enable).	Enumerationr/w Enumerated Values: 16 crc16 32 crc32	.1.3.6.1.4.1.43.2.16.2.1.7
a3ComPathAdminStatusmandatory This object enables or disables a path.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.43.2.16.2.1.8
a3ComPathOperStatusmandatory The actual state of the path.	Enumeration Enumerated Values: 1 up 2 down 3 disabled 4 notAvailable 5 other	.1.3.6.1.4.1.43.2.16.2.1.9
a3ComPathBaudobsolete The baud rate for serial paths. For ethernet, token ring, or FDDI connections this has a value notApplicable(1). In order for any modifications to take effect, the path must be enabled(re-enabled if it is already enabl…	Enumerationr/w Enumerated Values: 1 notApplicable 2 baud1200 3 baud2400 4 baud4800 5 baud9600 6 baud19200 7 baud38400 8 baud56k 9 baud64k 10 baud128k 11 baud256k 12 baud448k 13 baud1536k 14 baud2048k 15 baud3072k 16 baud4000k 17 baud4608k 18 baud6144k 19 baud7680k 20 baud9216k 21 baud16000k 22 other	.1.3.6.1.4.1.43.2.16.2.1.10
a3ComPathConnmandatory The connector for the path. For ethernet, token ring, or FDDI connections this has a value notApplicable(1). In order for any modifications to take effect, the path must be enabled(re-enabled if it is already enable). …	Enumerationr/w Enumerated Values: 1 notApplicable 2 v35 3 rs232 4 rs449 5 g703 6 t3 7 isdnBri 8 isdnPri 9 auto 10 other 11 x21	.1.3.6.1.4.1.43.2.16.2.1.11
a3ComPathClockmandatory How the transmit clock is derived. For ethernet, token ring, or FDDI connections this has a value notApplicable(1). In order for any modifications to take effect, the path must be enabled(re-enabled if it is already en…	Enumerationr/w Enumerated Values: 1 notApplicable 2 internal 3 external	.1.3.6.1.4.1.43.2.16.2.1.12
a3ComPathLastChangemandatory The value of sysUpTime at the time the path entered its current operational state.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.13
a3ComPathSlotIndexmandatory The index number of the chassis slot into which the module (or board) that supports this Path is inserted.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.16.2.1.14
a3ComPathConnPosmandatory The relative position on the module (or board) of the physical connector that supports this path. The position is identified by an index, which starts at one with the upper left connector and continues left to right an…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.16.2.1.15
a3ComPathInOctetsmandatory The total number of octets received on the path, including framing characters.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.16
a3ComPathInUcastPktsmandatory The number of subnetwork-unicast packets delivered to a higher-layer protocol.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.17
a3ComPathInNUcastPktsmandatory The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.18
a3ComPathInDiscardsmandatory The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.19
a3ComPathInErrorsmandatory The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.20
a3ComPathInUnknownProtosmandatory The number of packets received via the path which were discarded because of an unknown or unsupported protocol.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.21
a3ComPathOutOctetsmandatory The total number of octets transmitted out of the path, including framing characters.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.22
a3ComPathOutUcastPktsmandatory The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.23
a3ComPathOutNUcastPktsmandatory The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.24
a3ComPathOutDiscardsmandatory The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer s…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.25
a3ComPathOutErrorsmandatory The number of outbound packets that could not be transmitted because of errors.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.16.2.1.26
a3ComPathBaudRatemandatory The baud rate for serial paths. For ethernet, token ring, or FDDI connections this reports the actual value, but SETs are not allowed for those Paths. In order for any modifications to take effect, the …	Integer32r/w Constraints: range: 0-100000000	.1.3.6.1.4.1.43.2.16.2.1.27
a3ComPathDuplexmandatory The duplex mode is for SDLC and V3. It describes the physical characteristics of the communication method used to control the request-to-send signal. It has three values which are full, half and auto. Th…	Enumerationr/w Enumerated Values: 1 full 2 half 3 auto	.1.3.6.1.4.1.43.2.16.2.1.28

A table of attached or remotely connect
network segments.

a3ComPortEntry row .1.3.6.1.4.1.43.2.17.2.1

Indexes

a3ComPortIndex

Column	Syntax	OID
a3ComPortIndexmandatory A unique value for each port. This corresponds to ifIndex for MIB II. The interface table from MIB II will contain additional information for this port, including its type, its name and its description.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.17.2.1.1
a3ComPortOwnermandatory This object indicates the owner for this port. User can set the owner using this object, however, if the owner does not match the actual physical interface card associated with this port, it is ignored. …	Enumerationr/w Enumerated Values: 1 ethernet 2 tokenRing 3 fddi 4 ppp 5 plg 6 x25 7 frameRelay 8 smds 9 auto 10 autoPpp 11 autoFr	.1.3.6.1.4.1.43.2.17.2.1.2
a3ComPortBoundaryRoutemandatory This object controls whether the Boundary Routing feature is enabled for this port. Note: this feature only applies to serial ports on a NB2 and will be disabled for non-serial ports. Note, when this pa…	Enumerationr/w Enumerated Values: 1 notApplicable 2 enabled 3 disabled	.1.3.6.1.4.1.43.2.17.2.1.3
a3ComPortBoundaryEncapmandatory This object decides the packet encapsulation rules to be applied to outgoing packets. If this is set to none (5), the boundary router on the other end of the serial link is capable of supporting translation. In this ca…	Enumerationr/w Enumerated Values: 1 notApplicable 2 ethernet 3 tokenring 4 fddi 5 none	.1.3.6.1.4.1.43.2.17.2.1.4
a3ComPortCosInterleaveobsolete (For bridging.) The number of high-priority packets that will be transmitted for each low-priority packet. If the value is 0, then low-priority packets will only be transmitted when there are no packets in the high-prio…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.17.2.1.5
a3ComPortMacAddrFmtARPmandatory This object indicates the MAC address format used in ARP packets sent by this port. Note, nonCanonical(2) is allowed only on Token Ring ports.	Enumerationr/w Enumerated Values: 1 canonical 2 nonCanonical	.1.3.6.1.4.1.43.2.17.2.1.6
a3ComPortMacAddrFmtIPXmandatory This determine the MAC address format used in IPX packets sent by this port. Note, nonCanonical(2) is allowed only on Token Ring ports.	Enumerationr/w Enumerated Values: 1 canonical 2 nonCanonical	.1.3.6.1.4.1.43.2.17.2.1.7
a3ComPortMacAddrFmtXNSmandatory This determines the MAC address format used in XNS packets sent by this port. Note, nonCanonical(2) is allowed only on Token Ring ports.	Enumerationr/w Enumerated Values: 1 canonical 2 nonCanonical	.1.3.6.1.4.1.43.2.17.2.1.8
a3ComPortPathmandatory The Path which is assigned to this port. In some cases, one or more Paths will be assigned to a single Port. This object will return the lowest number Path in that case. For those situations where more than one Port i…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.17.2.1.9
a3ComQueueInterleave1mandatory This object specifies the interleave factor between the high and medium priority port queues. Note, this applies only to HSS ports. For non-HSS ports, this object will have the value 0.	Integer32r/w Constraints: range: 0-10	.1.3.6.1.4.1.43.2.17.2.1.10
a3ComQueueInterleave2mandatory This object specifies the interleave factor between the medium and low priority port queues. Note, this applies only to HSS ports. For non-HSS ports, this object will have the value 0.	Integer32r/w Constraints: range: 0-10	.1.3.6.1.4.1.43.2.17.2.1.11
a3ComQueuePatternmandatory This identifies the relative ratios of high priority packets versus medium priority packets versus low priority packets (in that order) that will be transmitted by this port. These ratios are based on the current valu…	Enumeration Enumerated Values: 1 ratio3to3to2 2 ratio4to2to2 3 ratio4to3to1 4 ratio5to2to1 5 ratio6to1to1 6 other	.1.3.6.1.4.1.43.2.17.2.1.13
a3ComPortAsOwnerTimermandatory This object only applies to High Speed Serial ports. When the Owner of this port has been set to Auto, the system will also automatically determine the proper Owner to assign to the port. This object is used to ind…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.17.2.1.15
a3ComSmartFilteringCtlmandatory This object is used to enable or disable the Smart Filtering mechanism on a port. Note, this only applies to the Central Node in a boundary routing environment. Note, when this parameter is enabled/disab…	Enumerationr/w Enumerated Values: 1 smartFilter 2 noSmartFilter	.1.3.6.1.4.1.43.2.17.2.1.16
a3ComBrCentralMacCtlmandatory This object is used to enable or disable the Boundary Routing Central MAC feature. If this feature is enabled, (ie, if this object has the value centralMac(1)), the Central Node (in a Boundary Routing environment) wil…	Enumerationr/w Enumerated Values: 1 centralMac 2 noCentralMac	.1.3.6.1.4.1.43.2.17.2.1.17
a3ComPortLabelmandatory This object specifies the descriptive label assigned to this port by the router. These labels are used by the User Interface and are useful when comparing information retrieved via SNMP with information retrieved via t…	RFC1213-MIBDisplayString	.1.3.6.1.4.1.43.2.17.2.1.18
a3ComPortCircuitIDmandatory This object applies only to virtual ports and specifies the unique data link circuit or channel identifier assigned to this virtual port. For example, if this virtual port is attached to a Frame Relay network, this ob…	OctetStringr/w	.1.3.6.1.4.1.43.2.17.2.1.19
a3ComPortStatusmandatory This object is used to add or delete virtual ports. When adding a new virtual port, only the createAndGo method of adding rows is supported. Specifically, all essential elements of the row must be specified in the same…	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.17.2.1.20
a3ComPortNamemandatory The user-assigned name given to this port. Note, this name may not have any blanks.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.43.2.17.2.1.21
a3ComPortVirtualmandatory This object indicates whether this port is a virtual port or a normal port.	Enumeration Enumerated Values: 1 normal 2 virtual	.1.3.6.1.4.1.43.2.17.2.1.22
a3ComQueueThrottlemandatory This object specifies the maximum number of medium and low priority packets that can be sent to the line driver each time some packets are sent to the driver. A value of 0 means that there is no limit.	Integer32r/w Constraints: range: 0-40	.1.3.6.1.4.1.43.2.17.2.1.23
a3ComPortInCallerIdmandatory A text string to specify the effective Incoming CallerID for the port. This object must be successfully set for a port to use the dynamic dial pool. It is used by the port to decide if an incoming call should be accept…	OctetStringr/w Constraints: range: 0-31	.1.3.6.1.4.1.43.2.17.2.1.24
a3ComPortCompTypemandatory This object specifies the type of compression performed on this Port. NONE indicates that the compression is disabled. HIStory indicates that the compression is enabled and preserves the History across the frames and P…	Enumerationr/w Enumerated Values: 1 none 2 history 3 perPacket	.1.3.6.1.4.1.43.2.17.2.1.25
a3ComPortX25ProtIDmandatory This object specifies the X25 ProtolID used when running in Boundary Routed Mode for establishing the Virtual Circuits over X25 Link.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.43.2.17.2.1.26
a3ComPortIbmTrafficmandatory This object is used to enable or disable the SmartFiltering of IBM Traffic mechanism on a port. Note, this only applies to the Central Node in a boundary routing environment. Note, when this parameter i…	Enumerationr/w Enumerated Values: 1 ibmTraffic 2 noibmTraffic	.1.3.6.1.4.1.43.2.17.2.1.27

A table of physical interfaces.

a3ComPathDialEntry row .1.3.6.1.4.1.43.2.18.2.1

Indexes

a3ComPathDialIndex

Column	Syntax	OID
a3ComPathDialIndexmandatory A unique identifier for each path. The value for each path must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.18.2.1.1
a3ComPathDialTypemandatory When assigning multiple paths for a single port, and one or more of those paths is a dial-up Path, this object must identify which Path is the primary Path and whether it is a leased or dial-up Path. Similarly, the oth…	Enumerationr/w Enumerated Values: 1 primaryLeased 2 primaryDial 3 secondaryDial 4 other 5 primaryAuto 6 secondaryAuto 7 secondaryLeased 8 primaryAutoLeased 9 primaryAutoDial 10 secondaryAutoLeased 11 secondaryAutoDial	.1.3.6.1.4.1.43.2.18.2.1.2
a3ComPathDialCtlmandatory For those Paths for which the value of a3ComPathDialType is primaryDial(2) or secondaryDial(3), this object is used to control whether that Path may originate and/or answer calls. If this object has the v…	Enumerationr/w Enumerated Values: 1 answerOriginate 2 answerNoOriginate 3 noAnswerOriginate 4 noAnswerNoOriginate	.1.3.6.1.4.1.43.2.18.2.1.3
a3ComPathDialActionmandatory This object is used to initiate an action to be taken by the primary dial-up Path. If this is set to dial(1), then the Path is brought up using the number stored by a3ComPathDialNum. This is only allowed for primary …	Enumerationr/w Enumerated Values: 1 dial 2 hangUp 3 other	.1.3.6.1.4.1.43.2.18.2.1.4
a3ComPathDialNummandatory This object contains the telephone number of the remote sit to be dialed. This is used whenever a dial-up Path is brought up. Spaces and hyphens (-) are allowed and ignored, and semi-colons (;) indicate a delay (as su…	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.43.2.18.2.1.5
a3ComPathDialDodIdleTimeobsolete This object applies only to a path that is setup as a PrimaryDial path in DialOnDemand mode. It defines the amount of time, in seconds, to wait after detecting the lack of user traffic on the dial path, before bringing …	Integer32r/w Constraints: range: 1-3600	.1.3.6.1.4.1.43.2.18.2.1.6
a3ComPathDialModemandatory This object is used for setting/reading the Dial Mode of a dialup path. Only values (1) and (2) can be set to the object: If the object is (1), the dialup path is configured for V25 mode dialing. If the …	Enumerationr/w Enumerated Values: 1 v25Dial 2 dtrDial 3 autoV25 4 autoDTR	.1.3.6.1.4.1.43.2.18.2.1.7
a3ComPathDialDynContmandatory This object is used to specify whether the dialup path is of type static(1) or dynamic(3). If a path is made dynamic, it will automatically be assigned(added) into the pool of dynamic paths. Making a path static will …	Enumerationr/w Enumerated Values: 1 static 2 dynamic 3 other	.1.3.6.1.4.1.43.2.18.2.1.8
a3ComPathDialLocalDialNumbermandatory The telephone number assigned to the local ISDN unit. This number and the local subaddress number, if present, are used primarily to determine if the unit should answer an incoming call. Valid only for ISDN. Any ASCII…	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.43.2.18.2.1.9
a3ComPathDialLocalSubAddressmandatory The subaddress number assigned to the local ISDN unit. If the local dial number criterion passes, then the local subaddress number, if present, is the next criterion used to determine if an incoming call should be answ…	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.43.2.18.2.1.10
a3ComPathDialSPIDDN1mandatory The Service Profile Identification number assigned by a North American ISDN switch provider to identify the service profile of a ISDN unit. Valid characters are numeric IA5 characters ( 0 to 9 ). Maximum number of ch…	OctetStringr/w Constraints: range: 0-37	.1.3.6.1.4.1.43.2.18.2.1.11
a3ComPathDialSPIDDN2mandatory The second Service Profile Identification number assigned by a North American ISDN switch provider to identify the service profile of a ISDN unit. Valid characters are numeric IA5 characters ( 0 to 9 ). Maximum number…	OctetStringr/w Constraints: range: 0-37	.1.3.6.1.4.1.43.2.18.2.1.12
a3ComPathDialRateAdaptionmandatory Specifies the data rate to be used on the ISDN B channel. Rate64 and Rate56 specify that the channel be connected at 64K or 56K, respectively. The connection attempt would fail if the ISDN network does not support this.…	Enumerationr/w Enumerated Values: 1 auto 2 rate64 3 rate56	.1.3.6.1.4.1.43.2.18.2.1.13
a3ComPathDialSwitchTypemandatory Specifies the ISDN switch type the unit is connected to. The path has to be enabled for the new setting to take effect.	Enumerationr/w Enumerated Values: 1 etsi 2 ntt 3 ni1 4 att5ess 5 dms100	.1.3.6.1.4.1.43.2.18.2.1.14
a3ComPathDialExDevTypemandatory This object describes the external device type that is connected to the serial-line type (eg, HSS, HDWAN) path. It is applicable only for a dialup path. Use bri(1) setting if the path is connected to a d…	Enumerationr/w Enumerated Values: 1 bri 2 modem 3 sw56 4 other	.1.3.6.1.4.1.43.2.18.2.1.15

A table of attached or remotely connect
network segments.

a3ComPortDialEntry row .1.3.6.1.4.1.43.2.19.2.1

Indexes

a3ComPortDialIndex

Column	Syntax	OID
a3ComPortDialIndexmandatory A unique value for each port. This corresponds to ifIndex for MIB II. The interface table from MIB II will contain additional information for this port, including its type, its name and its description.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.19.2.1.1
a3ComPortDialDisasterCtlmandatory This object applies only to those Ports to which multiple Paths are assigned, at least one of which is a dial-up Path. If this is set to disasterRecovery(1), then this Port will switch all its traffic to …	Enumerationr/w Enumerated Values: 1 disasterRecovery 2 noDisasterRecovery	.1.3.6.1.4.1.43.2.19.2.1.2
a3ComPortDialBandOnDmndmandatory This object applies only to those Ports to which multiple Paths are assigned, at least one of which is a dial-up Path. If this is set to bandwidthOnDemand(1), then this Port will switch all its traffic to…	Enumerationr/w Enumerated Values: 1 bandwidthOnDemand 2 noBandwidthOnDemand	.1.3.6.1.4.1.43.2.19.2.1.3
a3ComPortDialDebounceTimeUpmandatory This object defines the amount of time, in seconds, to wait after the primary Path has gone down before bringing the secondary dial-up Path up. If the primary Path stays in the down state for this amount …	Integer32r/w Constraints: range: 0-3600	.1.3.6.1.4.1.43.2.19.2.1.4
a3ComPortDialDebounceTimeDownmandatory This object defines the amount of time, in seconds, to wait after the primary Path has come up before bringing the secondary, dial-up, Path down. If the primary Path remains in the up state for this amoun…	Integer32r/w Constraints: range: 0-3600	.1.3.6.1.4.1.43.2.19.2.1.5
a3ComPortDialInitStatemandatory This object applies only to Ports which have paths setup as PrimaryDial paths. It is used to configure the PrimaryDial path as a dial initiator operating in one of the following modes: noDialOut(1), whi…	Enumerationr/w Enumerated Values: 1 noDialOut 2 manualDial 3 dialOnDemand	.1.3.6.1.4.1.43.2.19.2.1.6
a3ComPortDialRcvrStatemandatory This object applies only to Ports which have paths setup as PrimaryDial paths. It is used to configure the PrimaryDial path as a dial receiver operating in one of the following modes: noAnswer(1), which d…	Enumerationr/w Enumerated Values: 1 noAnswer 2 answer	.1.3.6.1.4.1.43.2.19.2.1.7
a3ComPortDialActionmandatory This object is used to initiate manual dial or hangup action to be taken by the dialup port. If this is set to dial(1), the port will attempt to dial out on its Primary Dial path using the first destination phone number…	Enumerationr/w Enumerated Values: 1 dial 2 hangUp 3 other	.1.3.6.1.4.1.43.2.19.2.1.8
a3ComPortDialDodIdleTimemandatory This object applies only to a port that is setup as a dial initiator in DialOnDemand mode. It defines the amount of time, in seconds, to wait after detecting the lack of user traffic on its primary dial path before brin…	Integer32r/w Constraints: range: 1-3600	.1.3.6.1.4.1.43.2.19.2.1.9
a3ComPortDialIdleTimemandatory This object applies only to a port that is setup as a dial initiator in ManualDial mode. It defines the amount of time, in seconds, to wait after detecting the lack of user traffic on any of its active dial path befor…	Integer32r/w Constraints: range: 0-3600	.1.3.6.1.4.1.43.2.19.2.1.10
a3ComPortDialDodCallsMademandatory The cumulative total number of outgoing calls successfully initiated by the port operating in DialOnDemand mode.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.19.2.1.11
a3ComPortDialDodCallsFailmandatory The cumulative total number of outgoing calls unsuccessfully initiated by the port operating in DialOnDemand mode.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.19.2.1.12
a3ComPortDialDodUpTimemandatory The cumulative length of time in seconds that the Primary path of a port operating in DialOnDemand mode is Up.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.19.2.1.13
a3ComPortDialDodPktsOutmandatory The cumulative total number of user-data packets sent out by the port operating in DialOnDemand mode.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.43.2.19.2.1.14
a3ComPortDialBODTHresholdmandatory %BODTHreshold% This object specifies the level of sensitivity to bring up a BOD path for a port. The larger BODTHreshold value, the less sensitive to bring up BOD path. For DOD port, when the BODTHreshold is set to 0,…	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.43.2.19.2.1.15

A table representing the PoolPreference lists for dynamic
dialup ports. A PoolPreference list is a prioritized list of
dynamic dial paths that a port can use, and it is optional.
Each entry in the list is represented as a row in the table, 
and it contains a dynamic dial path number and its priority-
postion in the list. Priority is in descending position order
and it specifies the preference of the port for a particular path.
All objects in this table are applicable only for a dynamic
dial port, ie, a port with an effective InCallerID, before these
objects are specified.

a3ComPortDialPoolPrefEntry row .1.3.6.1.4.1.43.2.19.3.1

Indexes

a3ComPortDialPoolPrefPort a3ComPortDialPoolPrefPathPos

Column	Syntax	OID
a3ComPortDialPoolPrefPortmandatory Specifies the port number(portid), used as an index together with a3ComPortDialPoolPrefPathPos, to select a particular row entry.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.19.3.1.1
a3ComPortDialPoolPrefPathPosmandatory Specifies the position(priority) in the PoolPreference list of a path, for the port. Used as an index together with a3ComPortDialPoolPrefPort to select a particular row entry.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.19.3.1.2
a3ComPortDialPoolPrefPathNummandatory Specifies the path number(pathid) of a dynamic dial path that will be taken out from the dynamic dial pool and added into the PoolPreference list for the port.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.19.3.1.3
a3ComPortDialPoolPrefStatusmandatory This object is used to add or delete a dynamic dial path in the PoolPreference list of a port. Each path and its position in the list is represented as a row. When adding a new path, only the createAndGo method of addin…	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.19.3.1.4

A table representing the PhoneNo lists for dialup ports.
Setting up a PhoneNo list is optional for static dialup port,
but is required for dynamic dialup port. 
A PhoneNo list is a prioritized list of destination phone
numbers that a port can use to dial out to. Each entry in
the list is represented as a row in the table and it contains
a phone number, the phone type, its baudrate and its priority
(position) in the list. Priority is in descending postion
order; and it specifies the preference of the port for a
particular phone number.
All objects in this table are applicable only for a dialup
port.

a3ComPortDialPhoneListEntry row .1.3.6.1.4.1.43.2.19.4.1

Indexes

a3ComPortDialPhoneListPort a3ComPortDialPhoneListPos

Column	Syntax	OID
a3ComPortDialPhoneListPortmandatory Specifies the port number(portid), used as an index together with a3ComPortDialPhoneListPos, to select a particular row entry.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.19.4.1.1
a3ComPortDialPhoneListPosmandatory Specifies the position(priority) in the PhoneNo list of a phone number, for this port. Used as an index together with a3ComPortDialPhoneListPort, to select a particular row entry.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.43.2.19.4.1.2
a3ComPortDialPhoneListPhoneNomandatory A text string representing a phone number in the PhoneNo list of a port. The phone number is used as the destination phone number to call for an outgoing call. In the case of an ISDN dial line, this text string may als…	OctetStringr/w Constraints: range: 1-51	.1.3.6.1.4.1.43.2.19.4.1.3
a3ComPortDialPhoneListTypemandatory Used to specify the phone type attribute of a phone number in the PhoneNo list - either of type ISDN(1) or type Analog(2) or other(3).	Enumerationr/w Enumerated Values: 1 iSDN 2 analog 3 other	.1.3.6.1.4.1.43.2.19.4.1.4
a3ComPortDialPhoneListBaudmandatory Used to specify the Baud rate attribute of a phone number in the PhoneList.	Integer32r/w Constraints: range: 0-100000000	.1.3.6.1.4.1.43.2.19.4.1.5
a3ComPortDialPhoneListStatusmandatory This object is used to add or delete a phone number from the PhoneNo list of a port. Each phone number and its associated attributes (phone type, Baud rate, and priority-position) is containned in a row. When adding a …	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.43.2.19.4.1.6