atmVccAal2AppId

ZhoneAAL2-MIB · .1.3.6.1.4.1.5504.4.2.1.1.1.1

Object

column r/w Enumeration

STR-VMOA-LES-01-00 4.1.1 Application Identifier (AppId)
              
The Application Identifier (AppId) specifies protocol 
combinations used between IWFs.  
              
The following AppId values can be found at the 
ATM Forum public web site in section 5 of 'ATM 
Forum Well-known Addresses and Assigned Codes'.
              
0000000A      Loop Emulation Service using CAS (POTS only)
              without ELCP
0000000B      Loop Emulation Service using PSTN signalling (POTS only)
              without ELCP. Note: This application is not currently 
              supported.
0000000C      Loop Emulation Service using PSTN signalling (POTS only)
              with ELCP. Note: This application is not currently supported.
0000000D      Loop Emulation Service using DSS1 in support of BRI
              (BRI only) without ELCP
0000000E      Loop Emulation Service using DSS1 in support of BRI
              (BRI only) with ELCP. Note: This application is not currently
              supported.   
0000000F      Loop Emulation Service using CAS in support of POTS,
              and DSS1 in support of BRI (without ELCP). Note: This 
              application is not currently supported.   
00000010      Loop Emulation Service using PSTN signalling in support
              of POTS, and DSS1 in support of BRI (without ELCP).Note:
              This application is not currently supported 
00000011      Loop Emulation Service using PSTN signalling in support
              of POTS,and DSS1 in support of BRI (with ELCP). Note: This
              application is not currently supported.
00000012      Loop Emulation Service using other variety of CCS. Note: 
              This application is not currently supported. 
00000013      Unspecified mode of Loop Emulation Service. Note: This 
              application is not currently supported. 
000000FF      This is a Zhone proprietary application id and indicates
              that the protocol is Jetstream Aal2.
By default this value is set to casPotsOnlyNoElcp.

Context

MIB: ZhoneAAL2-MIB
OID: .1.3.6.1.4.1.5504.4.2.1.1.1.1
Type: column
Access: readwrite
Status: current
Parent: aal2VclEntry
Table: aal2VclTable
Siblings: 26

Syntax

Enumeration

Values & Constraints

Enumerated Values

`10`	casPotsOnlyNoElcp
`11`	pstnPotsOnlyNoElcp
`12`	pstnPotsOnlyElcp
`13`	dss1BriOnlyNoElcp
`14`	dss1BriOnlyElcp
`15`	casPotsDss1BriNoElcp
`16`	pstnPotsDss1BriNoElcp
`17`	pstnPotsDss1BriElcp
`18`	otherCcs
`255`	jetstream

Related Objects

Sibling Objects

Object	Type	Syntax	OID
aal2VclNextCid The Channel Identifier is one of the indicies for the CID table, aal2CidTable. The Application Identifier, atmVccAal2AppId, determines the valid range of values for the aal2Cid…	column	Integer32	`.1.3.6.1.4.1.5504.4.2.1.1.1.10`
aal2VclTimerCU Value of the 'combined use' Timer_CU. The combined use Timer_CU assures that CPS-Packets with one or more octets already packed, wait at most the duration of Timer_CU before b…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.5504.4.2.1.1.1.11`
aal2VclAudioService The service provided is the transfer of audio signals (voice, voiceband data, and facsimile). The data unit traversing the SAP (SSCS SDU) contains either a voice …	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.12`
aal2VclCircuitModeData The service provided is the transfer of circuit mode data. The circuit mode data service is an emulation of the N*64 kbit/s (N = 1, 2, ..., 30) unrestricted, 8 kHz structured ci…	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.13`
aal2VclFrameModeData Frame mode data is an intermittent data stream containing delimited units of information, possibly of varying size, with idle intervals between them. The service…	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.14`
aal2VclFaxDemoRemo Facsimile Demodulation/Remodulation is the process of detecting facsimile traffic, extracting digital information from the incoming analogue modulated signal, transporting thi…	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.15`
aal2VclCAS Channel Associated Signalling Bits are bits dedicated for connection control across a 1544 kbit/s or 2048 kbit/s interface that carries 64 kbit/s channels. Procedures are based …	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.16`
aal2VclTrunkType Trunk type specifies the signaling method currently used. Valid types are loop start,ground start and loop reverse battery. The default value is loop start. An instance of this ob…	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.17`
aal2VclDTMFDialedDigits DTMF Dialed Digits Dialed Digits are multifrequency audio tones typically used for inter-register signalling of addresses during call set-up or for end-to-end de…	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.18`
aal2VclMfR1DialedDigits MF-R1 Dialed Digits. See description for atmVccAal2DTMFDialedDigits. Valid values are enabled and disabled.	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.19`
atmVccAal2VccI STR-VMOA-LES-01-00 4.1.2 VCC Identifier (VCCI) To distinguish multiple VCCs, each shall be assigned a VCCI. The creator of an SVC shall assign its VCCI. The VCCI…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.5504.4.2.1.1.1.2`
aal2VclMfR2DialedDigits MF-R2 Dialed Digits. See description for atmVccAal2DTMFDialedDigits. Valid values are enabled and disabled.	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.20`
aal2VclPCMEncoding Encoding Data Unit is an octet-aligned concatenation of one or more frames of an audio algorithm, entailing a specific format of the bits. Every audio packet and SDU contains…	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.21`
aal2VclMaxLengthFrame Maximum length for frame mode data. Valid values are 1..65535.	column	octets Integer32	`.1.3.6.1.4.1.5504.4.2.1.1.1.22`
aal2VclMaxSDULength Max_SDU_Length indicates the maximum size SSSAR-SDU, in octets, that is allowed to be reassembled. Significance to peer-to-peer. The maximum size of an SSSAR-SDU…	column	octets Integer32	`.1.3.6.1.4.1.5504.4.2.1.1.1.23`
aal2VclRasTimer The reassembly timer RAS_Timer assures that the reassembly of an SSSAR-SDU does not exceed a certain time; if such timer supervision is not required, the timer is disabled by s…	column	milliseconds SNMPv2-SMIInteger32	`.1.3.6.1.4.1.5504.4.2.1.1.1.24`
aal2VclCellsReceived Total cells received	column	cells SNMPv2-SMIGauge32	`.1.3.6.1.4.1.5504.4.2.1.1.1.25`
aal2VclCellsSent Total cells sent	column	cells SNMPv2-SMIGauge32	`.1.3.6.1.4.1.5504.4.2.1.1.1.26`
aal2VclStatsTimeElapsed The number of seconds that have elapsed since the beginning of the current collection period. If, for some reason, such as an adjustment in the system's time-of-day clock, the …	column	seconds SNMPv2-SMIInteger32	`.1.3.6.1.4.1.5504.4.2.1.1.1.27`
atmVccAal2SigVccI STR-VMOA-LES-01-00 4.1.3 Signaling VCC Identifier (SigVCCI) If an AAL2 VCC is controlled by CCS, then SigVCCI = VCCI is indicated. Conversely if SigVCCI = VCCI t…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.5504.4.2.1.1.1.3`
aal2VclAudioProfileIdentifier The Audio Profile for this VCL entry is specified by the Audio Profile identifier. The range of valid Audio Profile identifiers is well-defined. The Audio Profile identifier in…	column	Integer32	`.1.3.6.1.4.1.5504.4.2.1.1.1.4`
aal2VclSscsDefaultType STR-VMOA-LES-01-00 4.1.4 SSCS Type The SSCS type that applies to each channel of an AAL2 VCC will vary according to the usage of that channel. Channels that are …	column	Enumeration	`.1.3.6.1.4.1.5504.4.2.1.1.1.5`
aal2VclMaxCpsSduSize Maximum length of a CPS-SDU (Max_CPS-SDU_Length). Permitted values: 45 or 64 octets.	column	octets Integer32	`.1.3.6.1.4.1.5504.4.2.1.1.1.6`
aal2VclMaxNumberMultiplexChannels Maximum number of multiplexed channels. Peer-to-peer significance. Valid range of values is 1..255.	column	channels Integer32	`.1.3.6.1.4.1.5504.4.2.1.1.1.7`
aal2VclMinCidForAal2UserChannels Minimum CID value for AAL2 user channels. Valid range is 1..255. If the field atmVccAal2AppId is set to casPotsOnlyNoElcp then the valid range for aal2VclMinCidForA…	column	Integer32	`.1.3.6.1.4.1.5504.4.2.1.1.1.8`
aal2VclMaxCidForAal2UserChannels Maximum CID value for AAL2 user channels. Valid range is 1..255. Maximum CID is 255. If the field atmVccAal2AppId is set to casPotsOnlyNoElcp then the valid range…	column	Integer32	`.1.3.6.1.4.1.5504.4.2.1.1.1.9`