zxPwCTDMCfgConfErr
ZXPW-TDM-MIB ·
.1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.3
Object
column
Bits
Various configuration errors. Illegal settings within the zxPwCTDMCfg table.
Context
- MIB
- ZXPW-TDM-MIB
- OID
.1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.3- Type
- column
- Access
- readonly
- Status
- current
- Parent
- zxPwCTDMCfgEntry
- Table
- zxPwCTDMCfgTable
- Siblings
- 21
Syntax
Bits
Values & Constraints
Enumerated Values
0 | other |
1 | payloadSize |
2 | jtrBfrDepth |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| zxPwCTDMCfgIndex Index to an entry in this table. The value is a copy of the
assigned zxPwCTDMCfgIndexNext | column | PwTDMCfgIndex | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.1 |
| zxPwCTDMCfgConsecMissPktsOutSynch The number of consecutive missing packets that are
required to enter the LOPS state. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.10 |
| zxPwCTDMCfgSetUp2SynchTimeOut The amount of time the host should wait before declaring the
pseudo wire in down state, if the number of consecutive
TDM packets that have been received after changing the
admins… | column | millisecond SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.11 |
| zxPwCTDMCfgPktReplacePolicy This parameter determines the value to be played when CE bound
packets have over/underflow the jitter buffer, or are missing
for any reason. This byte pattern is sent (played) on
… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.12 |
| zxPwCTDMCfgAvePktLossTimeWindow The length of time over which the average packet
loss rate should be computed to detect Excessive packet
loss rate | column | millisecond SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.13 |
| zxPwCTDMCfgExcessivePktLossThreshold Excessive packet loss rate is detected by computing the
average packetloss rate over a zxPwCTDMCfgAvePktLossTimeWindow
amount of time and comparing it with this threshold value. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.14 |
| zxPwCTDMCfgAlarmThreshold Alarms are only reported when the defect state persists
for the length of time specified by this object.
The object's unit is millisec | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.15 |
| zxPwCTDMCfgClearAlarmThreshold Alarm MUST be cleared after the corresponding defect is
undetected for the amount of time specified by this object.
The object's unit is millisec | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.16 |
| zxPwCTDMCfgMissingPktsToSes Number of missing packets detected (consecutive or not)
within a 1 second window to cause a Severely Error
Second (SES) to be counted. | column | seconds SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.17 |
| zxPwCTDMCfgTimestampMode Timestamp generation MAY be used in one of the following
modes:
1. Absolute mode: the PSN-bound IWF sets timestamps
using the clock recovered from the incoming TDM attachment
ci… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.18 |
| zxPwCTDMCfgQueueSize The actual queue size is the 'zxPwCTDMCfgQueueSize' power of 2.
The range of this object is from 1 to 10. But when resequencing,
the maximum value is 7. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.19 |
| zxPwCTDMCfgRowStatus Object used for creating, modifying, and deleting
a row from this table. The following objects should not be
modified if the entry is in used and the status is active:
zxPwCTDMCfg… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.2 |
| zxPwCTDMCfgName | column | OctetString | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.20 |
| zxPwCTDMCfgSSRC This object must be set when zxPwCTDMCfgRtpHdrUsed is 'TRUE'. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.21 |
| zxPwCTDMCfgStorageType This variable indicates the storage type for this
row. | column | SNMPv2-TCStorageType | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.22 |
| zxPwCTDMCfgPayloadSize The value of this object indicates the PayLoad Size (in bytes)
to be defined during the PW setUp. Upon TX, implementation
must be capable of carrying that amount of bytes.
Upon RX… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.4 |
| zxPwCTDMCfgPktReorder If set True: as CE bound packets are queued in the
jitter buffer, out of order packets are re-ordered. The
maximum sequence number differential (i.e., the range in
which re-sequen… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.5 |
| zxPwCTDMCfgRtpHdrUsed If set to False: an RTP header is not pre-pended to the
TDM packet. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.6 |
| zxPwCTDMCfgJtrBfrDepth The size of this buffer SHOULD be locally
configured to allow accommodation to the PSN-specific packet
delay variation.
If configured to a value not supported by th… | column | microsecond SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.7 |
| zxPwCTDMCfgPayloadSuppression Selecting 'enable' means: Payload suppression is allowed.
Payload MAY be omitted in order to conserve bandwidth.
Selecting 'disable' means: no suppresion under any
condition. | column | Enumeration | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.8 |
| zxPwCTDMCfgConsecPktsInSynch The number of consecutive packets with sequential
sequence numbers that are required to exit the
LOPS state. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.1013.2.1.2.1.3.1.9 |