zxAdslLinePMState
ZTE-DSL-LINE-EXT-MIB ·
.1.3.6.1.4.1.3902.1004.4.1.1.1.2
Object
column
Enumeration
The Line has four possible power management states, numbered 0 to 3
and corresponding to respectively:
L0 - Synchronized - This Line state (L0) is when the Line has
full transmission (i.e. showtime).
L1 - Power Down Data transmission - This line state (L1) is when
there is transmission on the line but the net data rate is
reduced (e.g. only for OAM and higher layer connection and
session control). This state applies to G.992.2 only.
L2 - Power Down Data transmission - This line state (L2) is when
there is transmission on the line but the net data rate is
reduced (e.g. only for OAM and higher layer connection and
session control). This state applies to G.992.3 and G.992.4 only.
L3 - No power - This Line state (L3) is when there is No Power
transmitted on the line at all.
NOTE - This parameter maps to the OperStatus of the line, which is
part of the GeneralInformationGroup object group specified
in RFC 2233, and may not need to be duplicated in the ADSL MIB.
See also RFC2662 and RFC3440. The Operational Status of the
line is UP in the L0, L1 or L2 state (i.e., during showtime)
and is DOWN in the L3 state (e.g., during (short)
initialization and loop diagnostics mode).
Context
- MIB
- ZTE-DSL-LINE-EXT-MIB
- OID
.1.3.6.1.4.1.3902.1004.4.1.1.1.2- Type
- column
- Access
- readonly
- Status
- current
- Parent
- zxAdslLineEntry
- Table
- zxAdslLineTable
- Siblings
- 7
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | l0_FullOn |
2 | l1_LowPower |
3 | l2_LowPower |
4 | l3_Idle |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| zxAdslLinePMConfPMSF This configuration parameter defines the line states to be forced by
the near-end ATU on this line. It is coded as an integer value with
following definition:
L0_FullOn Fo… | column | Enumeration | .1.3.6.1.4.1.3902.1004.4.1.1.1.1 |
| zxAdslLineDMTTrellis deprecated Parameter that indicates whether trellis coding has been enabled or
disabled.Trellis coding should always be enabled for its clear
performancen advantage.Trellis coding is mandat… | column | Enumeration | .1.3.6.1.4.1.3902.1004.4.1.1.1.3 |
| zxAdslLineTxAtmCells Transmitted ATM cell counter.This is a count of total data cells
only transmitted by ATU-C. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.3902.1004.4.1.1.1.4 |
| zxAdslLineRxAtmCells Received ATM cell counter.This is a count of total data cells
only received by ATU-C. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.3902.1004.4.1.1.1.5 |
| zxAdslLineIdleCells Number of idle cells transmitted/recieved by ATU-C. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.3902.1004.4.1.1.1.6 |
| zxAdslLineTxDataRate Transmitted net data rate on this line. | column | kbps SNMPv2-SMIGauge32 | .1.3.6.1.4.1.3902.1004.4.1.1.1.7 |
| zxAdslLineRxDataRate Recieved net data rate on this line. | column | kbps SNMPv2-SMIGauge32 | .1.3.6.1.4.1.3902.1004.4.1.1.1.8 |