zxAnLdpMplsLabelRetentionMode
ZTE-AN-LDP-MIB ·
.1.3.6.1.4.1.3902.1015.55.1.23
Object
scalar
r/w
Enumeration
To specify retention mode of LSP.
Context
- MIB
- ZTE-AN-LDP-MIB
- OID
.1.3.6.1.4.1.3902.1015.55.1.23- Type
- scalar
- Access
- readwrite
- Status
- current
- Parent
- zxAnLdpGlobalObjects
- Siblings
- 23
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | conservative |
2 | liberal |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| zxAnLdpMplsEnable Enable MPLS service. | scalar | Enumeration | .1.3.6.1.4.1.3902.1015.55.1.1 |
| zxAnLdpMplsSessMaxBackoffTime The maximum time which LDP entity could use to rebuild session
after LDP failed to establish a session. The waiting time starts
from the initial back off time, then increases expo… | scalar | seconds Integer32 | .1.3.6.1.4.1.3902.1015.55.1.10 |
| zxAnLdpMplsSessKeepAliveTime The timer which is the proposed keep alive hold timer
for LDP session. | scalar | seconds Integer32 | .1.3.6.1.4.1.3902.1015.55.1.11 |
| zxAnLdpMplsGrEnable LDP GR(Graceful Restart) function enable switch.
It indicates whether LDP GR function should be enabled. | scalar | Enumeration | .1.3.6.1.4.1.3902.1015.55.1.12 |
| zxAnLdpMplsGrRecoveryTime The maximum time which is the proposed GR recovery timer
for this LDP entity. After LDP session rebuilt, GR Helper
assists GR Restarter to update label forwarding table. | scalar | seconds Integer32 | .1.3.6.1.4.1.3902.1015.55.1.13 |
| zxAnLdpMplsGrNeighKeepAliveTime The maximum time which is the proposed keep alive neighbor
when a LDP entity found the peer is down. | scalar | seconds Integer32 | .1.3.6.1.4.1.3902.1015.55.1.14 |
| zxAnLdpMplsVpnGrEnable MPLS Layer 2 VPN GR function enable switch. | scalar | Enumeration | .1.3.6.1.4.1.3902.1015.55.1.15 |
| zxAnLdpMplsHelloHoldTime The timer which is the proposed Hello hold timer for this
LDP entity. A value of 65535 means infinite. | scalar | seconds Integer32 | .1.3.6.1.4.1.3902.1015.55.1.16 |
| zxAnLdpMplsHelloSendInterval The time interval to send Hello message for this LDP entity.
The time must be smaller than the hello hold time. | scalar | seconds Integer32 | .1.3.6.1.4.1.3902.1015.55.1.17 |
| zxAnLdpMplsTgtHelloHoldTime The timer which is the proposed targeted Hello hold timer for
this LDP entity. A value of 65535 means infinite. | scalar | seconds Integer32 | .1.3.6.1.4.1.3902.1015.55.1.18 |
| zxAnLdpMplsTgtHelloSendInterval The time interval to send targeted Hello message for this
LDP entity. The time must be smaller than the targeted hello
hold time. | scalar | seconds Integer32 | .1.3.6.1.4.1.3902.1015.55.1.19 |
| zxAnLdpMplsMinLabel Minimum value in dynamic label range of MPLS.
For OLT C300, the label value range from 16 to 1044478. | scalar | Integer32 | .1.3.6.1.4.1.3902.1015.55.1.2 |
| zxAnLdpMplsKeepSessWithHelloMsg LDP session keeping alive with hello messages enable switch.
If the switch is enabling, the LDP session reset keep alive timer
when receiving a hello message. | scalar | Enumeration | .1.3.6.1.4.1.3902.1015.55.1.20 |
| zxAnLdpMplsGrHelperEnable Graceful restart helper enable switch. | scalar | Enumeration | .1.3.6.1.4.1.3902.1015.55.1.21 |
| zxAnLdpMplsLabelControlMode To specify control mode of LSP. | scalar | Enumeration | .1.3.6.1.4.1.3902.1015.55.1.22 |
| zxAnLdpMplsPktWithLabelEnable To specify label encapsulation mode when LSR
sending protocol packets. | scalar | Enumeration | .1.3.6.1.4.1.3902.1015.55.1.24 |
| zxAnLdpMplsMaxLabel Maximum value in dynamic label range of MPLS.
For OLT C300, the label value range from 16 to 1044478,
and the default maximum value is 1044478. | scalar | Integer32 | .1.3.6.1.4.1.3902.1015.55.1.3 |
| zxAnLdpMplsLdpRouterId A zxAnL3IfIndex is used as the LDP router ID. It is recommended
to use loopback interface as LDP router ID. L3 VLAN interface
also can be configed. IP address of zxAnL3IfIndex sho… | scalar | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.55.1.4 |
| zxAnLdpMplsLdpRouterIdForce zxAnLdpMplsLdpRouterId is valid immediately. When force is set
whether the router ID designated takes effect depends on the
current status of the designated interface.
When cur… | scalar | Enumeration | .1.3.6.1.4.1.3902.1015.55.1.5 |
| zxAnLdpMplsExplicitNullEnable MPLS explicit null label enable switch. | scalar | Enumeration | .1.3.6.1.4.1.3902.1015.55.1.6 |
| zxAnLdpMplsMinInUseLabel Minimum value in dynamic label range of MPLS in use.
For OLT C300, the label value ranges from 16 to 1044478. | scalar | Integer32 | .1.3.6.1.4.1.3902.1015.55.1.7 |
| zxAnLdpMplsMaxInUseLabel Maximum value in dynamic label range of MPLS in use.
For OLT C300, the label value ranges from 16 to 1044478. | scalar | Integer32 | .1.3.6.1.4.1.3902.1015.55.1.8 |
| zxAnLdpMplsSessInitBackoffTime The initial time which LDP entity should wait and try again
after LDP failed to establish a session. | scalar | seconds Integer32 | .1.3.6.1.4.1.3902.1015.55.1.9 |