zxAnLdpMplsGrRecoveryTime

ZTE-AN-LDP-MIB · .1.3.6.1.4.1.3902.1015.55.1.13
MIB view Table view

Object

scalar r/w seconds Integer32 
The maximum time which is the proposed GR recovery timer
for this LDP entity. After LDP session rebuilt, GR Helper
assists GR Restarter to update label forwarding table.

Context

MIB
ZTE-AN-LDP-MIB
OID
.1.3.6.1.4.1.3902.1015.55.1.13
Type
scalar
Access
readwrite
Status
current
Units
seconds
Parent
zxAnLdpGlobalObjects
Siblings
23

Syntax

seconds Integer32

Values & Constraints

Object Constraints
range: 15-600

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
zxAnLdpMplsEnable
Enable MPLS service.
scalarEnumeration.1.3.6.1.4.1.3902.1015.55.1.1
zxAnLdpMplsSessMaxBackoffTime
The maximum time which LDP entity could use to rebuild session after LDP failed to establish a session. The waiting time starts from the initial back off time, then increases expo…
scalarseconds Integer32.1.3.6.1.4.1.3902.1015.55.1.10
zxAnLdpMplsSessKeepAliveTime
The timer which is the proposed keep alive hold timer for LDP session.
scalarseconds Integer32.1.3.6.1.4.1.3902.1015.55.1.11
zxAnLdpMplsGrEnable
LDP GR(Graceful Restart) function enable switch. It indicates whether LDP GR function should be enabled.
scalarEnumeration.1.3.6.1.4.1.3902.1015.55.1.12
zxAnLdpMplsGrNeighKeepAliveTime
The maximum time which is the proposed keep alive neighbor when a LDP entity found the peer is down.
scalarseconds Integer32.1.3.6.1.4.1.3902.1015.55.1.14
zxAnLdpMplsVpnGrEnable
MPLS Layer 2 VPN GR function enable switch.
scalarEnumeration.1.3.6.1.4.1.3902.1015.55.1.15
zxAnLdpMplsHelloHoldTime
The timer which is the proposed Hello hold timer for this LDP entity. A value of 65535 means infinite.
scalarseconds Integer32.1.3.6.1.4.1.3902.1015.55.1.16
zxAnLdpMplsHelloSendInterval
The time interval to send Hello message for this LDP entity. The time must be smaller than the hello hold time.
scalarseconds Integer32.1.3.6.1.4.1.3902.1015.55.1.17
zxAnLdpMplsTgtHelloHoldTime
The timer which is the proposed targeted Hello hold timer for this LDP entity. A value of 65535 means infinite.
scalarseconds Integer32.1.3.6.1.4.1.3902.1015.55.1.18
zxAnLdpMplsTgtHelloSendInterval
The time interval to send targeted Hello message for this LDP entity. The time must be smaller than the targeted hello hold time.
scalarseconds Integer32.1.3.6.1.4.1.3902.1015.55.1.19
zxAnLdpMplsMinLabel
Minimum value in dynamic label range of MPLS. For OLT C300, the label value range from 16 to 1044478.
scalarInteger32.1.3.6.1.4.1.3902.1015.55.1.2
zxAnLdpMplsKeepSessWithHelloMsg
LDP session keeping alive with hello messages enable switch. If the switch is enabling, the LDP session reset keep alive timer when receiving a hello message.
scalarEnumeration.1.3.6.1.4.1.3902.1015.55.1.20
zxAnLdpMplsGrHelperEnable
Graceful restart helper enable switch.
scalarEnumeration.1.3.6.1.4.1.3902.1015.55.1.21
zxAnLdpMplsLabelControlMode
To specify control mode of LSP.
scalarEnumeration.1.3.6.1.4.1.3902.1015.55.1.22
zxAnLdpMplsLabelRetentionMode
To specify retention mode of LSP.
scalarEnumeration.1.3.6.1.4.1.3902.1015.55.1.23
zxAnLdpMplsPktWithLabelEnable
To specify label encapsulation mode when LSR sending protocol packets.
scalarEnumeration.1.3.6.1.4.1.3902.1015.55.1.24
zxAnLdpMplsMaxLabel
Maximum value in dynamic label range of MPLS. For OLT C300, the label value range from 16 to 1044478, and the default maximum value is 1044478.
scalarInteger32.1.3.6.1.4.1.3902.1015.55.1.3
zxAnLdpMplsLdpRouterId
A zxAnL3IfIndex is used as the LDP router ID. It is recommended to use loopback interface as LDP router ID. L3 VLAN interface also can be configed. IP address of zxAnL3IfIndex sho…
scalarSNMPv2-SMIInteger32.1.3.6.1.4.1.3902.1015.55.1.4
zxAnLdpMplsLdpRouterIdForce
zxAnLdpMplsLdpRouterId is valid immediately. When force is set whether the router ID designated takes effect depends on the current status of the designated interface. When cur…
scalarEnumeration.1.3.6.1.4.1.3902.1015.55.1.5
zxAnLdpMplsExplicitNullEnable
MPLS explicit null label enable switch.
scalarEnumeration.1.3.6.1.4.1.3902.1015.55.1.6
zxAnLdpMplsMinInUseLabel
Minimum value in dynamic label range of MPLS in use. For OLT C300, the label value ranges from 16 to 1044478.
scalarInteger32.1.3.6.1.4.1.3902.1015.55.1.7
zxAnLdpMplsMaxInUseLabel
Maximum value in dynamic label range of MPLS in use. For OLT C300, the label value ranges from 16 to 1044478.
scalarInteger32.1.3.6.1.4.1.3902.1015.55.1.8
zxAnLdpMplsSessInitBackoffTime
The initial time which LDP entity should wait and try again after LDP failed to establish a session.
scalarseconds Integer32.1.3.6.1.4.1.3902.1015.55.1.9