zxAnCfmMepTestPattern
ZTE-AN-CFM-MIB ·
.1.3.6.1.4.1.3902.1015.62.1.3.1.1.65
Object
column
r/w
Enumeration
Indicates the test pattern. This pattern will be used if the value of the column zxAnCfmMepTestTlvEnable is 'enable'.
Context
- MIB
- ZTE-AN-CFM-MIB
- OID
.1.3.6.1.4.1.3902.1015.62.1.3.1.1.65- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- zxAnCfmMepEntry
- Table
- zxAnCfmMepTable
- Siblings
- 65
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | allZeroesWithoutCrc32 |
2 | allZeroesWithCrc32 |
3 | prbsWithoutCrc32 |
4 | prbsWithCrc32 |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| zxAnCfmMepCcCheckEnable Enabled or disabled the CCM frame defect checking. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.1 |
| zxAnCfmMepLmEndType Indicates the end type of ETH-LM, which should be one-ended
or two-ended. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.10 |
| zxAnCfmMepLmInterval The interval at which LMMs are sent by a MEP, the default
value is 5 seconds. | column | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.11 |
| zxAnCfmMepLmDuration The time of duration of ETH-LM test, the default value is
60 seconds. | column | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.12 |
| zxAnCfmMepLmPriority The priority value for LMMs transmitted by the MEP.
Default Value is the highest priority value allowed to pass
through the bridge port for any of this MEPs VIDs.
The management e… | column | Unsigned32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.13 |
| zxAnCfmMepLmFarendLoss The number of far-end frame loss. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.14 |
| zxAnCfmMepLmNearendLoss The number of near-end frame loss. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.15 |
| zxAnCfmMepLmLossRatio The near-end frame loss ratio in percent. | column | Integer32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.16 |
| zxAnCfmMepLmStatus A Boolean flag set to true by the MEP LM Initiator State
Machine or an MIB manager to indicate
that another LM is being transmitted.
Reset to false by the MEP LM Initiator State M… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.17 |
| zxAnCfmMepLmResultOk Indicates the result of the operation:
- true The Loss Measurement Message(s) will be
(or has been) sent.
- false The Loss Measurement Messa… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.18 |
| zxAnCfmMepLmFarendLossRatio The far-end frame loss ratio in percent. | column | Integer32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.19 |
| zxAnCfmMepLmEnable Enabled or disabled the ETH-LM functions. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.2 |
| zxAnCfmMepDmEnable Enabled or disabled the ETH-DM functions. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.3 |
| zxAnCfmMepDmTargetMacAddress The Target MAC Address Field to be transmitted: A unicast
destination MAC address.
This address will be used if the value of the column
dot1agCfmMepDmTargetIsMepId is 'false'. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.30 |
| zxAnCfmMepDmTargetMepId An indication of the Target MAC Address Field to be
transmitted:
The Maintenance association End Point Identifier of
another MEP in the same Maintenance Association
This address w… | column | IEEE8021-CFM-MIBDot1agCfmMepIdOrZero | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.31 |
| zxAnCfmMepDmTargetIsMepId True indicates that MEPID of the target MEP is used for Linktrace
transmission.
False indicates that unicast destination MAC address of the
target MEP is used for DM transmission. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.32 |
| zxAnCfmMep1dmDaType The da type of 1DM. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.33 |
| zxAnCfmMepDdmDaType The da type of DDM. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.34 |
| zxAnCfmMepDmWayType The DM way type. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.35 |
| zxAnCfmMepDmInterval The interval at which DMMs are sent by a MEP, the default value
is 5 seconds. | column | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.36 |
| zxAnCfmMepDmDuration The time of duration of ETH-DM test, the default value is
60 seconds. | column | seconds SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.37 |
| zxAnCfmMepDmPriority The priority value for DMMs transmitted by the MEP.
Default Value is the highest priority value allowed to pass
through the bridge port for any of this MEPs VIDs.
The management e… | column | Unsigned32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.38 |
| zxAnCfmMepDmOneWayAvgDelay The number of One-way Frame Delay. | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.39 |
| zxAnCfmMepLbmTestType Indicates the type of ETH-LBM is unicast or multicast. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.4 |
| zxAnCfmMepDmOneWayAvgDv The number of One-way Frame Delay variation. | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.40 |
| zxAnCfmMepDmTwoWayAvgDelay The number of Two-way Frame Delay. | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.41 |
| zxAnCfmMepDmTwoWayAvgDv The number of Two-way Frame Delay variation. | column | SNMPv2-SMICounter64 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.42 |
| zxAnCfmMepDmStatus A Boolean flag set to true by the MEP DM Initiator State
Machine or an MIB manager to indicate that another LBM is
being transmitted.
Reset to false by the MEP DM Initiator State… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.43 |
| zxAnCfmMepDmResultOk Indicates the result of the operation:
- true The Delay Measurement Message(s) will be
(or has been) sent.
- false The Delay Measurement Mes… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.44 |
| zxAnCfmMepLbmAppType Indicates the app type of ETH-LBM, which means to verify
bidirectional connectivity of a MEP with a MIP or a peer MEP,
or to perform a bidirectional in-service or out-of-service… | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.5 |
| zxAnCfmMepTestTlvLength The length of test TLV.
This object can be used if the value of the column
zxAnCfmMepTestTlvEnable is 'enable'. | column | Unsigned32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.54 |
| zxAnCfmMepTestEnable Enabled or disabled the ETH-Test functions. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.55 |
| zxAnCfmMepTestAppType Indicates the app type of ETH-Test, which means to
perform a bidirectional in-service or out-of-service
diagnostics test between a pair of peer MEPs.
This includes verifying band… | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.56 |
| zxAnCfmMepTestDestMacAddress The destination MAC address field to be transmitted: A unicast
destination MAC address.
This address will be used if the value of the column
zxAnCfmMepTestDestIsMepId is 'false'. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.57 |
| zxAnCfmMepTestDestMepId The maintenance association end point identifier of another
MEP in the same maintenance association to which the ETH-Test
message is to be sent.
This address will be used if the … | column | IEEE8021-CFM-MIBDot1agCfmMepIdOrZero | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.58 |
| zxAnCfmMepTestDestIsMepId True indicates that MEPID of the destination MEP is used for
ETH-Test transmission.
False indicates that unicast destination MAC address of the
target MEP is used for ETH-Test tra… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.59 |
| zxAnCfmMepLmTargetMacAddress The Target MAC Address Field to be transmitted: A unicast
destination MAC address.
This address will be used if the value of the column
dot1agCfmMepLmTargetIsMepId is 'false'. | column | SNMPv2-TCMacAddress | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.6 |
| zxAnCfmMepTestInterval The interval value for ETH-Test messages transmitted by the MEP.
the default value is 1000 milliseconds. | column | milliseconds Integer32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.60 |
| zxAnCfmMepTestDuration The time of duration of ETH-Test, the default value is
60 seconds. | column | seconds Integer32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.61 |
| zxAnCfmMepTestPriority The priority value for ETH-Test Messages transmitted by the MEP.
Default value is the highest priority value allowed to pass
through the bridge port for any of this MEPs VIDs.
The… | column | Unsigned32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.62 |
| zxAnCfmMepTestDaType The destination address type of ETH-Test Message. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.63 |
| zxAnCfmMepTestTlvEnable Enabled or disabled ETH-Test TLV. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.64 |
| zxAnCfmMepTestStatus A Boolean flag set to true by the MEP TEST initiator state
machine or an MIB manager to indicate that another ETH-Test is
being done.
Reset to false by the MEP TEST initiator sta… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.66 |
| zxAnCfmMepTestResultOk Indicates the result of the operation:
- true The ETH-Test message(s) will be (or has been) sent.
- false The ETH-Test message(s) will not be sent. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.67 |
| zxAnCfmMepTestMsgSeqNumber The ETH-Test transaction identifier
(zxAnCfmMepTestNextMsgSeqNumber) of the first ETH-Test
message(to be) sent. The value returned is undefined if
zxAnCfmMepTestResultOk is fal… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.68 |
| zxAnCfmMepTestNextMsgSeqNumber Next sequence number/transaction identifier to be sent in a
ETH-Test message. This sequence number can be zero because
it wraps around. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.69 |
| zxAnCfmMepLmTargetMepId An indication of the Target MAC Address Field to be
transmitted:
The Maintenance association End Point Identifier of
another MEP in the same Maintenance Association
This address w… | column | IEEE8021-CFM-MIBDot1agCfmMepIdOrZero | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.7 |
| zxAnCfmMepTestTransmitRate Indicates the maximum transmission rate at which frames with
ETH-Test information can be sent. | column | kbps Unsigned32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.70 |
| zxAnCfmMepTestFarendLossRatio The far-end frame loss ratio in percent. | column | Integer32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.71 |
| zxAnCfmMepTestFarendBitErrRatio The far-end received bit error ratio in percent. | column | Integer32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.72 |
| zxAnCfmMepLmTargetIsMepId True indicates that MEPID of the target MEP is used for
Linktrace transmission.
False indicates that unicast destination MAC address of the
target MEP is used for LM transmission. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.8 |
| zxAnCfmMepAisEnable Enabled or disabled the ETH-AIS functions. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.87 |
| zxAnCfmMepLckEnable Enabled or disabled the ETH-LCK functions. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.88 |
| zxAnCfmMepAisClientMegLevel MEG level at which the most immediate client layer MIPs and MEPs
exist. | column | Integer32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.89 |
| zxAnCfmMepLmmDaType Indicates the da type of LMM. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.9 |
| zxAnCfmMepLckClientMegLevel MEG level at which the most immediate client layer MIPs and MEPs
exist. | column | Integer32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.90 |
| zxAnCfmMepAisLckInterval The interval value for AISMs and LCKMs transmitted by the MEP.
the default value is 1 second. | column | seconds Integer32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.91 |
| zxAnCfmMepAisPriority The priority value for AISMs transmitted by the MEP.
Default value is the highest priority value allowed to pass
through the bridge port for any of this MEPs VIDs.
The management … | column | Unsigned32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.92 |
| zxAnCfmMepLckPriority The priority value for LCKMs transmitted by the MEP.
Default value is the highest priority value allowed to pass
through the bridge port for any of this MEPs VIDs.
The management … | column | Unsigned32 | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.93 |
| zxAnCfmMepAisDaType The destination address type of AISM. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.94 |
| zxAnCfmMepLckDaType The destination address type of LCKM. | column | Enumeration | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.95 |
| zxAnCfmMepAisStatus This object represents if MEP is in AIS status or not. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.96 |
| zxAnCfmMepLckStatus This object represents if MEP is in LCK status or not. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.97 |
| zxAnCfmMepLckSendEnable This object represents if LCK message can be sent by the MEP. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.98 |
| zxAnCfmMepRdiStatus This object represents if MEP is in RDI status or not. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.3902.1015.62.1.3.1.1.99 |