zxAnAdslLineConfUseCustomBins

ZTE-AN-ADSL-LINE-MIB · .1.3.6.1.4.1.3902.1015.1000.1.2.1.5

Object

column r/w Enumeration

Enable or disable custom bin selection for upstream/downstream 
transmission. This parameter is used in conjunction with the
adslAtucDMTConfFreqBins and 
adslAturDMTConfFreqBins[ADSL-DMT-LINE-MIB] parameter.

Context

MIB: ZTE-AN-ADSL-LINE-MIB
OID: .1.3.6.1.4.1.3902.1015.1000.1.2.1.5
Type: column
Access: readwrite
Status: current
Parent: zxAnAdslLineConfProfileExtEntry
Table: zxAnAdslLineConfProfileExtTable
Siblings: 18

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	enable
`2`	disable

Related Objects

Sibling Objects

Object	Type	Syntax	OID
zxAnAdslLineConfTxStartBin Specifies lowest bin number allowed for Tx signal. Different line coding type has different default value. 0x20 (default for Annex A only) 0x20 (default for ADSL2/ADSL2plus)…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.1`
zxAnAdslLineConfMinProtectionUs Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols.	column	symbols Enumeration	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.10`
zxAnAdslConfDMTConfTrellis Parameter that enable or disable trellis coding. Trellis coding should always be enabled for its clear performance advantage. Trellis coding is mandatory for ADSL/ADSL2plus. The …	column	Enumeration	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.11`
zxAnAdslAtucConfMaxBitsPerBin Specifies maximum Rx number of bits per bin.	column	Integer32	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.12`
zxAnAdslAtucConfBitSwapDs enables/disables downstream bit swapping. Different line coding type has different default value. disable(2) (default for ADSL2/ADLS2plus, Annex B, Annex C C.…	column	Enumeration	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.13`
zxAnAdslAtucConfBitSwapUs enables/disables upstream bit swapping. Different line coding type has different default value. disable(2) (default for ADSL2/ADLS2plus, Annex B, Annex C C.x,…	column	Enumeration	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.14`
zxAnAdslAtucConfReAdsl2Enable Defines whether downstream READSL2 operation should be forced by the ATU-C.	column	Enumeration	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.15`
zxAnAdslAtucConfPmL0Time PM configuration parameter,related to the L2 low power state. This parameter represents the minimum time between an exit from the L2 state and the next entry into the L2 state.	column	seconds Integer32	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.16`
zxAnAdslAtucConfPmL2Time PM configuration parameter,related to the L2 low power state. This parameter represents the minimum time between an entry into the L2 state and the first Power Trim in the L2 stat…	column	seconds Integer32	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.17`
zxAnAdslAtucConfPmL2Atpr PM configuration parameter,related to the L2 low power state. This parameter represents the Maximum Aggregate Transmit Power Reduction (in dB) that can be performed through a sin…	column	dB Integer32	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.18`
zxAdsl2ConfPsdMaskSelectUs The selected upstream PSD mask. This parameter is used only for annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled bits in adslLineTr…	column	Enumeration	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.19`
zxAnAdslLineConfTxEndBin Specifies highest bin number allowed for Tx signal. Default = 0x3ff (default for all Annexes and ADSL2/ADSL2plus)	column	Integer32	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.2`
zxAnAdslLineConfRxStartBin Specifies lowest bin number allowed for Rx signal. Different line coding type has different default value. 0x06 (default for Annex A) 0x01 (default for Annex B) 0x06 (def…	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.3`
zxAnAdslLineConfRxEndBin Specifies highest bin number allowed for Rx signal. Default = 0x3f (default for all Annexes and ADSL2/ADLS2plus)	column	Integer32	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.4`
zxAnAdslAtucConfPsdMaskType It is supported by G.Span. Dsl card team will provide files about it in details.	column	SNMPv2-SMIInteger32	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.6`
zxAnAdslLineConfPMMode This configuration parameter defines the line states the ATU-C may autonomously transition to on this line. It is coded in a bit map representation (0 if not allowed, 1 if allowe…	column	Bits	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.7`
zxAnAdslLineConfPML2Rate PM configuration parameter,related to the L2 low power state. This parameter specifies the minimum net data rate during the low power state (L2).	column	kbps Integer32	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.8`
zxAnAdsl2ConfMinProtectionDs Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following…	column	symbols Enumeration	`.1.3.6.1.4.1.3902.1015.1000.1.2.1.9`