zxAnAdslAtucConfPmL0Time
ZTE-AN-ADSL-LINE-MIB ·
.1.3.6.1.4.1.3902.1015.1000.1.2.1.16
Object
column
r/w
seconds Integer32
PM configuration parameter,related to the L2 low power state. This parameter represents the minimum time between an exit from the L2 state and the next entry into the L2 state.
Context
- MIB
- ZTE-AN-ADSL-LINE-MIB
- OID
.1.3.6.1.4.1.3902.1015.1000.1.2.1.16- Type
- column
- Access
- readwrite
- Status
- current
- Units
- seconds
- Parent
- zxAnAdslLineConfProfileExtEntry
- Table
- zxAnAdslLineConfProfileExtTable
- Siblings
- 18
Syntax
seconds Integer32
Values & Constraints
Object Constraints
range: 0-255
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| zxAnAdslLineConfTxStartBin Specifies lowest bin number allowed for Tx signal.
Different line coding type has different default value.
0x20 (default for Annex A only)
0x20 (default for ADSL2/ADSL2plus)… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.1000.1.2.1.1 |
| zxAnAdslLineConfMinProtectionUs Minimum Impulse Noise Protection on Upstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. | column | symbols Enumeration | .1.3.6.1.4.1.3902.1015.1000.1.2.1.10 |
| zxAnAdslConfDMTConfTrellis Parameter that enable or disable trellis coding. Trellis coding
should always be enabled for its clear performance advantage.
Trellis coding is mandatory for ADSL/ADSL2plus.
The … | column | Enumeration | .1.3.6.1.4.1.3902.1015.1000.1.2.1.11 |
| zxAnAdslAtucConfMaxBitsPerBin Specifies maximum Rx number of bits per bin. | column | Integer32 | .1.3.6.1.4.1.3902.1015.1000.1.2.1.12 |
| zxAnAdslAtucConfBitSwapDs enables/disables downstream bit swapping.
Different line coding type has different default value.
disable(2) (default for ADSL2/ADLS2plus, Annex B, Annex C
C.… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1000.1.2.1.13 |
| zxAnAdslAtucConfBitSwapUs enables/disables upstream bit swapping.
Different line coding type has different default value.
disable(2) (default for ADSL2/ADLS2plus, Annex B, Annex C
C.x,… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1000.1.2.1.14 |
| zxAnAdslAtucConfReAdsl2Enable Defines whether downstream READSL2 operation should be forced
by the ATU-C. | column | Enumeration | .1.3.6.1.4.1.3902.1015.1000.1.2.1.15 |
| zxAnAdslAtucConfPmL2Time PM configuration parameter,related to the L2 low power state.
This parameter represents the minimum time between an entry into
the L2 state and the first Power Trim in the L2 stat… | column | seconds Integer32 | .1.3.6.1.4.1.3902.1015.1000.1.2.1.17 |
| zxAnAdslAtucConfPmL2Atpr PM configuration parameter,related to the L2 low power state.
This parameter represents the Maximum Aggregate Transmit Power
Reduction (in dB) that can be performed through a sin… | column | dB Integer32 | .1.3.6.1.4.1.3902.1015.1000.1.2.1.18 |
| zxAdsl2ConfPsdMaskSelectUs The selected upstream PSD mask. This parameter is used only
for annexes J and M of G.992.3 and G.992.5, and the same
selection is used for all relevant enabled bits in
adslLineTr… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1000.1.2.1.19 |
| zxAnAdslLineConfTxEndBin Specifies highest bin number allowed for Tx signal.
Default = 0x3ff (default for all Annexes and ADSL2/ADSL2plus) | column | Integer32 | .1.3.6.1.4.1.3902.1015.1000.1.2.1.2 |
| zxAnAdslLineConfRxStartBin Specifies lowest bin number allowed for Rx signal.
Different line coding type has different default value.
0x06 (default for Annex A)
0x01 (default for Annex B)
0x06 (def… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.1000.1.2.1.3 |
| zxAnAdslLineConfRxEndBin Specifies highest bin number allowed for Rx signal.
Default = 0x3f (default for all Annexes and ADSL2/ADLS2plus) | column | Integer32 | .1.3.6.1.4.1.3902.1015.1000.1.2.1.4 |
| zxAnAdslLineConfUseCustomBins Enable or disable custom bin selection for upstream/downstream
transmission. This parameter is used in conjunction with the
adslAtucDMTConfFreqBins and
adslAturDMTConfFreqBins[A… | column | Enumeration | .1.3.6.1.4.1.3902.1015.1000.1.2.1.5 |
| zxAnAdslAtucConfPsdMaskType It is supported by G.Span. Dsl card team will provide files
about it in details. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.3902.1015.1000.1.2.1.6 |
| zxAnAdslLineConfPMMode This configuration parameter defines the line states the ATU-C
may autonomously transition to on this line. It is coded in a
bit map representation (0 if not allowed, 1 if allowe… | column | Bits | .1.3.6.1.4.1.3902.1015.1000.1.2.1.7 |
| zxAnAdslLineConfPML2Rate PM configuration parameter,related to the L2 low power state.
This parameter specifies the minimum net data rate during the
low power state (L2). | column | kbps Integer32 | .1.3.6.1.4.1.3902.1015.1000.1.2.1.8 |
| zxAnAdsl2ConfMinProtectionDs Minimum Impulse Noise Protection on Downstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following… | column | symbols Enumeration | .1.3.6.1.4.1.3902.1015.1000.1.2.1.9 |